+++ /dev/null
-ps2avrGB keyboard firmware
-==========================
-
-This is a port of the QMK firmware for boards that are based on the
-ps2avrGB firmware, like the [ps2avrGB
-keyboard](https://www.keyclack.com/product/gb-ps2avrgb/) or the ones sold
-by [Winkeyless](http://winkeyless.kr/product/ps2avrgb-parts/).
-
-Note that this is a complete replacement for the firmware, so you won't be
-using Bootmapper Client to change any keyboard settings, since not all the
-USB report options are supported.
-
-This is an example based on the b.mini keyboard for making other keyboards
-compatible with QMK; fully supported boards have their own directory.
-
-## Supported Boards
-
-- [b.fake](https://github.com/qmk/qmk_firmware/tree/master/keyboards/bfake)
-- [b.mini](https://github.com/qmk/qmk_firmware/tree/master/keyboards/bmini)
-- [b.face](https://github.com/qmk/qmk_firmware/tree/master/keyboards/bface)
-- [pearl](https://github.com/qmk/qmk_firmware/tree/master/keyboards/pearl)
-
-## Installing
-
-First, install the requirements. These commands are for OSX, but all you
-need is the AVR toolchain and `bootloadHID` for flashing:
-
-```
-$ brew cask install crosspack-avr
-$ brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
-```
-
-In order to use the `./util/atmega32a_program.py` script, which can reboot the board into
-the bootloader, you'll need Python 2 with PyUSB installed:
-
-```
-$ pip install pyusb
-```
-
-Then, with the keyboard plugged in, simply run this command from the
-`qmk_firmware` directory:
-
-```
-$ make ps2avrGB:program
-```
-
-If you prefer, you can just build it and flash the firmware directly with
-`bootloadHID` if you boot the board while holding down `L_Ctrl` to keep it
-in the bootloader:
-
-```
-$ make ps2avrGB
-$ bootloadHID -r ps2avrGB_default.hex
-```
-
-## Setting the board to bootloader mode
-
-If you're lucky, the programming script does this automagically for you. If
-however this doesn't work for you, you need to enter the bootloader mode manually
-by plugging the keyboard in while holding the bootloader key. If you did this
-correctly the LEDs will blink and you'll be able to flash your firmware.
-
-The bootloader key is the top left key of your matrix. For a standard board
-from winkeyless.kr this is `L_Ctrl`, but for some custom boards running ps2avrGB
-this might be different. For the Pearl it's `Esc`, for a b.fake it is `q`. If
-you're unsure you should be able to see the key in the bootmapper client.
-
-
-## Troubleshooting
-
-From my experience, it's really hard to brick these boards. But these
-tricks have been useful when it got stuck in a weird scenario.
-
-1. Try plugging the board in while holding the bootloader key. This will force
- it to boot only the bootloader without loading the firmware. Once this is
- done, just reflash the board with the original firmware.
-2. Sometimes USB hubs can act weird, so try connecting the board directly
- to your computer or plugging/unplugging the USB hub.
+++ /dev/null
-/*
-Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef BMINI_H
-#define BMINI_H
-
-#include "quantum.h"
-
-#define KEYMAP( \
- K05, K25, K35, K45, K55, K06, KA6, KA7, K07, KB5, KC5, KD5, KE5, KD1, KE1, KE2, \
- K04, K14, K24, K34, K44, K54, K16, KB6, KB7, K17, KA4, KB4, KC4, KE4, KD0, \
- K03, K13, K23, K33, K43, K53, K26, KC6, KC7, K27, KA3, KB3, KC3, KD3, K67, \
- K02, K12, K22, K32, K42, K52, K36, KD6, KD7, K37, KA2, KB2, KD2, KE0, \
- K01, K11, K21, K31, K41, K51, K46, KE6, KE7, K47, KA1, KB1, K86, K77, \
- K00, K10, K20, K56, K57, KB0, KC0, K66, K76, K96 \
-){ \
- { K00, K10, K20, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KB0, KC0, KD0, KE0 }, \
- { K01, K11, K21, K31, K41, K51, KC_NO, KC_NO, KC_NO, KC_NO, KA1, KB1, KC_NO, KD1, KE1 }, \
- { K02, K12, K22, K32, K42, K52, KC_NO, KC_NO, KC_NO, KC_NO, KA2, KB2, KC_NO, KD2, KE2 }, \
- { K03, K13, K23, K33, K43, K53, KC_NO, KC_NO, KC_NO, KC_NO, KA3, KB3, KC3, KD3, KC_NO }, \
- { K04, K14, K24, K34, K44, K54, KC_NO, KC_NO, KC_NO, KC_NO, KA4, KB4, KC4, KC_NO, KE4 }, \
- { K05, KC_NO, K25, K35, K45, K55, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KB5, KC5, KD5, KE5 }, \
- { K06, K16, K26, K36, K46, K56, K66, K76, K86, K96, KA6, KB6, KC6, KD6, KE6 }, \
- { K07, K17, K27, K37, K47, K57, K67, K77, KC_NO, KC_NO, KA7, KB7, KC7, KD7, KE7 } \
-}
-
-#define KC_KEYMAP( \
- K05, K25, K35, K45, K55, K06, KA6, KA7, K07, KB5, KC5, KD5, KE5, KD1, KE1, KE2, \
- K04, K14, K24, K34, K44, K54, K16, KB6, KB7, K17, KA4, KB4, KC4, KE4, KD0, \
- K03, K13, K23, K33, K43, K53, K26, KC6, KC7, K27, KA3, KB3, KC3, KD3, K67, \
- K02, K12, K22, K32, K42, K52, K36, KD6, KD7, K37, KA2, KB2, KD2, KE0, \
- K01, K11, K21, K31, K41, K51, K46, KE6, KE7, K47, KA1, KB1, K86, K77, \
- K00, K10, K20, K56, K57, KB0, KC0, K66, K76, K96 \
-) \
-{ \
- { KC_##K00, KC_##K10, KC_##K20, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_##KB0, KC_##KC0, KC_##KD0, KC_##KE0 }, \
- { KC_##K01, KC_##K11, KC_##K21, KC_##K31, KC_##K41, KC_##K51, KC_NO, KC_NO, KC_NO, KC_NO, KC_##KA1, KC_##KB1, KC_NO, KC_##KD1, KC_##KE1 }, \
- { KC_##K02, KC_##K12, KC_##K22, KC_##K32, KC_##K42, KC_##K52, KC_NO, KC_NO, KC_NO, KC_NO, KC_##KA2, KC_##KB2, KC_NO, KC_##KD2, KC_##KE2 }, \
- { KC_##K03, KC_##K13, KC_##K23, KC_##K33, KC_##K43, KC_##K53, KC_NO, KC_NO, KC_NO, KC_NO, KC_##KA3, KC_##KB3, KC_##KC3, KC_##KD3, KC_NO }, \
- { KC_##K04, KC_##K14, KC_##K24, KC_##K34, KC_##K44, KC_##K54, KC_NO, KC_NO, KC_NO, KC_NO, KC_##KA4, KC_##KB4, KC_##KC4, KC_NO, KC_##KE4 }, \
- { KC_##K05, KC_NO, KC_##K25, KC_##K35, KC_##K45, KC_##K55, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_##KB5, KC_##KC5, KC_##KD5, KC_##KE5 }, \
- { KC_##K06, KC_##K16, KC_##K26, KC_##K36, KC_##K46, KC_##K56, KC_##K66, KC_##K76, KC_##K86, KC_##K96, KC_##KA6, KC_##KB6, KC_##KC6, KC_##KD6, KC_##KE6 }, \
- { KC_##K07, KC_##K17, KC_##K27, KC_##K37, KC_##K47, KC_##K57, KC_##K67, KC_##K77, KC_NO, KC_NO, KC_##KA7, KC_##KB7, KC_##KC7, KC_##KD7, KC_##KE7 } \
-}
-
-#endif
+++ /dev/null
-/*
-Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#define VENDOR_ID 0x20A0
-#define PRODUCT_ID 0x422D
-// TODO: share these strings with usbconfig.h
-// Edit usbconfig.h to change these.
-#define MANUFACTURER winkeyless.kr
-#define PRODUCT ps2avrGB
-
-/* matrix size */
-#define MATRIX_ROWS 8
-#define MATRIX_COLS 15
-
-#define RGBLED_NUM 16
-#define RGBLIGHT_ANIMATIONS
-
-#define NO_UART 1
-#define BOOTLOADHID_BOOTLOADER 1
-
-#endif
+++ /dev/null
-/*
-Copyright 2016 Luiz Ribeiro <luizribeiro@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-// Please do not modify this file
-
-#include <avr/io.h>
-#include <util/twi.h>
-
-#include "i2c.h"
-
-void i2c_set_bitrate(uint16_t bitrate_khz) {
- uint8_t bitrate_div = ((F_CPU / 1000l) / bitrate_khz);
- if (bitrate_div >= 16) {
- bitrate_div = (bitrate_div - 16) / 2;
- }
- TWBR = bitrate_div;
-}
-
-void i2c_init(void) {
- // set pull-up resistors on I2C bus pins
- PORTC |= 0b11;
-
- i2c_set_bitrate(400);
-
- // enable TWI (two-wire interface)
- TWCR |= (1 << TWEN);
-
- // enable TWI interrupt and slave address ACK
- TWCR |= (1 << TWIE);
- TWCR |= (1 << TWEA);
-}
-
-uint8_t i2c_start(uint8_t address) {
- // reset TWI control register
- TWCR = 0;
-
- // begin transmission and wait for it to end
- TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
- while (!(TWCR & (1<<TWINT)));
-
- // check if the start condition was successfully transmitted
- if ((TWSR & 0xF8) != TW_START) {
- return 1;
- }
-
- // transmit address and wait
- TWDR = address;
- TWCR = (1<<TWINT) | (1<<TWEN);
- while (!(TWCR & (1<<TWINT)));
-
- // check if the device has acknowledged the READ / WRITE mode
- uint8_t twst = TW_STATUS & 0xF8;
- if ((twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK)) {
- return 1;
- }
-
- return 0;
-}
-
-void i2c_stop(void) {
- TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
-}
-
-uint8_t i2c_write(uint8_t data) {
- TWDR = data;
-
- // transmit data and wait
- TWCR = (1<<TWINT) | (1<<TWEN);
- while (!(TWCR & (1<<TWINT)));
-
- if ((TWSR & 0xF8) != TW_MT_DATA_ACK) {
- return 1;
- }
-
- return 0;
-}
-
-uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length) {
- if (i2c_start(address)) {
- return 1;
- }
-
- for (uint16_t i = 0; i < length; i++) {
- if (i2c_write(data[i])) {
- return 1;
- }
- }
-
- i2c_stop();
-
- return 0;
-}
+++ /dev/null
-/*
-Copyright 2016 Luiz Ribeiro <luizribeiro@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-// Please do not modify this file
-
-#ifndef __I2C_H__
-#define __I2C_H__
-
-void i2c_init(void);
-void i2c_set_bitrate(uint16_t bitrate_khz);
-uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length);
-
-#endif
+++ /dev/null
-/*
-Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#include QMK_KEYBOARD_H
-
-const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
- [0] = KEYMAP(
- KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR,KC_HOME,KC_END,
- KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS,KC_EQL, KC_BSPC, KC_DEL,
- KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC,KC_RBRC,KC_BSLS, KC_INS,
- MO(0), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN,KC_QUOT,KC_ENT, KC_PGUP,
- KC_LSFT,KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH,KC_RSFT, KC_UP, KC_PGDN,
- KC_LCTL,KC_LALT,KC_LGUI, KC_SPC, KC_RGUI,KC_RALT,KC_RCTL,KC_LEFT,KC_DOWN,KC_RGHT
- ),
- [1] = KEYMAP(
- KC_TRNS,RGB_TOG,RGB_MOD,RGB_HUI,RGB_SAI,RGB_VAI,RGB_HUD,RGB_SAD,RGB_VAD,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_END,
- KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_DEL,
- KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_INS,
- KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,
- KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,KC_TRNS,
- KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_RGHT
- ),
-};
+++ /dev/null
-/*
-Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#include <avr/io.h>
-#include <util/delay.h>
-
-#include "matrix.h"
-
-#ifndef DEBOUNCE
-# define DEBOUNCE 5
-#endif
-
-static uint8_t debouncing = DEBOUNCE;
-
-static matrix_row_t matrix[MATRIX_ROWS];
-static matrix_row_t matrix_debouncing[MATRIX_ROWS];
-
-void matrix_set_row_status(uint8_t row);
-uint8_t bit_reverse(uint8_t x);
-
-void matrix_init(void) {
- // all outputs for rows high
- DDRB = 0xFF;
- PORTB = 0xFF;
- // all inputs for columns
- DDRA = 0x00;
- DDRC &= ~(0x111111<<2);
- DDRD &= ~(1<<PIND7);
- // all columns are pulled-up
- PORTA = 0xFF;
- PORTC |= (0b111111<<2);
- PORTD |= (1<<PIND7);
-
- // initialize matrix state: all keys off
- for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
- matrix[row] = 0x00;
- matrix_debouncing[row] = 0x00;
- }
-
- matrix_init_quantum();
-}
-
-uint8_t matrix_scan(void) {
- for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
- matrix_set_row_status(row);
- _delay_us(5);
-
- matrix_row_t cols = (
- // cols 0..7, PORTA 0 -> 7
- (~PINA) & 0xFF
- ) | (
- // cols 8..13, PORTC 7 -> 0
- bit_reverse((~PINC) & 0xFF) << 8
- ) | (
- // col 14, PORTD 7
- ((~PIND) & (1 << PIND7)) << 7
- );
-
- if (matrix_debouncing[row] != cols) {
- matrix_debouncing[row] = cols;
- debouncing = DEBOUNCE;
- }
- }
-
- if (debouncing) {
- if (--debouncing) {
- _delay_ms(1);
- } else {
- for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
- matrix[i] = matrix_debouncing[i];
- }
- }
- }
-
- matrix_scan_quantum();
-
- return 1;
-}
-
-// declarations
-void matrix_set_row_status(uint8_t row) {
- DDRB = (1 << row);
- PORTB = ~(1 << row);
-}
-
-uint8_t bit_reverse(uint8_t x) {
- x = ((x >> 1) & 0x55) | ((x << 1) & 0xaa);
- x = ((x >> 2) & 0x33) | ((x << 2) & 0xcc);
- x = ((x >> 4) & 0x0f) | ((x << 4) & 0xf0);
- return x;
-}
-
-inline matrix_row_t matrix_get_row(uint8_t row) {
- return matrix[row];
-}
-
-void matrix_print(void) {
-}
+++ /dev/null
-/*
-Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#include "ps2avrGB.h"
-#include "rgblight.h"
-
-#include <avr/pgmspace.h>
-
-#include "action_layer.h"
-#include "i2c.h"
-#include "quantum.h"
-
-// for keyboard subdirectory level init functions
-// @Override
-void matrix_init_kb(void) {
- // call user level keymaps, if any
- matrix_init_user();
-}
-
-#ifdef RGBLIGHT_ENABLE
-extern rgblight_config_t rgblight_config;
-
-// custom RGB driver
-void rgblight_set(void) {
- if (!rgblight_config.enable) {
- for (uint8_t i=0; i<RGBLED_NUM; i++) {
- led[i].r = 0;
- led[i].g = 0;
- led[i].b = 0;
- }
- }
-
- i2c_init();
- i2c_send(0xb0, (uint8_t*)led, 3 * RGBLED_NUM);
-}
-
-bool rgb_init = false;
-
-void matrix_scan_kb(void) {
- // if LEDs were previously on before poweroff, turn them back on
- if (rgb_init == false && rgblight_config.enable) {
- i2c_init();
- i2c_send(0xb0, (uint8_t*)led, 3 * RGBLED_NUM);
- rgb_init = true;
- }
-
- rgblight_task();
-#else
-void matrix_scan_kb(void) {
-#endif
- matrix_scan_user();
- /* Nothing else for now. */
-}
-
-__attribute__((weak)) // overridable
-void matrix_init_user(void) {
-
-}
-
-
-__attribute__((weak)) // overridable
-void matrix_scan_user(void) {
-
-}
+++ /dev/null
-/*
-Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef KEYMAP_COMMON_H
-#define KEYMAP_COMMON_H
-
-#include "quantum.h"
-#include "bmini.h"
-
-#endif
+++ /dev/null
-# Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
-#
-# This program is free software: you can redistribute it and/or modify
-# it under the terms of the GNU General Public License as published by
-# the Free Software Foundation, either version 2 of the License, or
-# (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program. If not, see <http://www.gnu.org/licenses/>.
-
-# MCU name
-MCU = atmega32a
-PROTOCOL = VUSB
-
-# unsupported features for now
-NO_UART = yes
-NO_SUSPEND_POWER_DOWN = yes
-
-# processor frequency
-F_CPU = 12000000
-
-# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
-BOOTLOADER = atmel-dfu
-
-# build options
-BOOTMAGIC_ENABLE = full
-MOUSEKEY_ENABLE = no
-EXTRAKEY_ENABLE = yes
-CONSOLE_ENABLE = yes
-COMMAND_ENABLE = yes
-BACKLIGHT_ENABLE = no
-RGBLIGHT_ENABLE = yes
-RGBLIGHT_CUSTOM_DRIVER = yes
-
-OPT_DEFS = -DDEBUG_LEVEL=0
-
-# custom matrix setup
-CUSTOM_MATRIX = yes
-SRC = matrix.c i2c.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
+++ /dev/null
-/* Name: usbconfig.h
- * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
- * Author: Christian Starkjohann
- * Creation Date: 2005-04-01
- * Tabsize: 4
- * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
- */
-
-#ifndef __usbconfig_h_included__
-#define __usbconfig_h_included__
-
-#include "config.h"
-
-/*
-General Description:
-This file is an example configuration (with inline documentation) for the USB
-driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
-also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
-wire the lines to any other port, as long as D+ is also wired to INT0 (or any
-other hardware interrupt, as long as it is the highest level interrupt, see
-section at the end of this file).
-*/
-
-/* ---------------------------- Hardware Config ---------------------------- */
-
-#define USB_CFG_IOPORTNAME D
-/* This is the port where the USB bus is connected. When you configure it to
- * "B", the registers PORTB, PINB and DDRB will be used.
- */
-#define USB_CFG_DMINUS_BIT 3
-/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
- * This may be any bit in the port.
- */
-#define USB_CFG_DPLUS_BIT 2
-/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
- * This may be any bit in the port. Please note that D+ must also be connected
- * to interrupt pin INT0! [You can also use other interrupts, see section
- * "Optional MCU Description" below, or you can connect D- to the interrupt, as
- * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
- * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
- * markers every millisecond.]
- */
-#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
-/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
- * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
- * require no crystal, they tolerate +/- 1% deviation from the nominal
- * frequency. All other rates require a precision of 2000 ppm and thus a
- * crystal!
- * Since F_CPU should be defined to your actual clock rate anyway, you should
- * not need to modify this setting.
- */
-#define USB_CFG_CHECK_CRC 0
-/* Define this to 1 if you want that the driver checks integrity of incoming
- * data packets (CRC checks). CRC checks cost quite a bit of code size and are
- * currently only available for 18 MHz crystal clock. You must choose
- * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
- */
-
-/* ----------------------- Optional Hardware Config ------------------------ */
-
-/* #define USB_CFG_PULLUP_IOPORTNAME D */
-/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
- * V+, you can connect and disconnect the device from firmware by calling
- * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
- * This constant defines the port on which the pullup resistor is connected.
- */
-/* #define USB_CFG_PULLUP_BIT 4 */
-/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
- * above) where the 1.5k pullup resistor is connected. See description
- * above for details.
- */
-
-/* --------------------------- Functional Range ---------------------------- */
-
-#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
-/* Define this to 1 if you want to compile a version with two endpoints: The
- * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
- * number).
- */
-#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
-/* Define this to 1 if you want to compile a version with three endpoints: The
- * default control endpoint 0, an interrupt-in endpoint 3 (or the number
- * configured below) and a catch-all default interrupt-in endpoint as above.
- * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
- */
-#define USB_CFG_EP3_NUMBER 3
-/* If the so-called endpoint 3 is used, it can now be configured to any other
- * endpoint number (except 0) with this macro. Default if undefined is 3.
- */
-/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
-/* The above macro defines the startup condition for data toggling on the
- * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
- * Since the token is toggled BEFORE sending any data, the first packet is
- * sent with the oposite value of this configuration!
- */
-#define USB_CFG_IMPLEMENT_HALT 0
-/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
- * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
- * it is required by the standard. We have made it a config option because it
- * bloats the code considerably.
- */
-#define USB_CFG_SUPPRESS_INTR_CODE 0
-/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
- * want to send any data over them. If this macro is defined to 1, functions
- * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
- * you need the interrupt-in endpoints in order to comply to an interface
- * (e.g. HID), but never want to send any data. This option saves a couple
- * of bytes in flash memory and the transmit buffers in RAM.
- */
-#define USB_CFG_INTR_POLL_INTERVAL 1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
-#define USB_CFG_IS_SELF_POWERED 0
-/* Define this to 1 if the device has its own power supply. Set it to 0 if the
- * device is powered from the USB bus.
- */
-#define USB_CFG_MAX_BUS_POWER 500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
-#define USB_CFG_IMPLEMENT_FN_WRITE 1
-/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
- * transfers. Set it to 0 if you don't need it and want to save a couple of
- * bytes.
- */
-#define USB_CFG_IMPLEMENT_FN_READ 0
-/* Set this to 1 if you need to send control replies which are generated
- * "on the fly" when usbFunctionRead() is called. If you only want to send
- * data from a static buffer, set it to 0 and return the data from
- * usbFunctionSetup(). This saves a couple of bytes.
- */
-#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
-/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
- * You must implement the function usbFunctionWriteOut() which receives all
- * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
- * can be found in 'usbRxToken'.
- */
-#define USB_CFG_HAVE_FLOWCONTROL 0
-/* Define this to 1 if you want flowcontrol over USB data. See the definition
- * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
- * usbdrv.h.
- */
-#define USB_CFG_DRIVER_FLASH_PAGE 0
-/* If the device has more than 64 kBytes of flash, define this to the 64 k page
- * where the driver's constants (descriptors) are located. Or in other words:
- * Define this to 1 for boot loaders on the ATMega128.
- */
-#define USB_CFG_LONG_TRANSFERS 0
-/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
- * in a single control-in or control-out transfer. Note that the capability
- * for long transfers increases the driver size.
- */
-/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
-/* This macro is a hook if you want to do unconventional things. If it is
- * defined, it's inserted at the beginning of received message processing.
- * If you eat the received message and don't want default processing to
- * proceed, do a return after doing your things. One possible application
- * (besides debugging) is to flash a status LED on each packet.
- */
-/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
-/* This macro is a hook if you need to know when an USB RESET occurs. It has
- * one parameter which distinguishes between the start of RESET state and its
- * end.
- */
-/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
-/* This macro (if defined) is executed when a USB SET_ADDRESS request was
- * received.
- */
-#define USB_COUNT_SOF 1
-/* define this macro to 1 if you need the global variable "usbSofCount" which
- * counts SOF packets. This feature requires that the hardware interrupt is
- * connected to D- instead of D+.
- */
-/* #ifdef __ASSEMBLER__
- * macro myAssemblerMacro
- * in YL, TCNT0
- * sts timer0Snapshot, YL
- * endm
- * #endif
- * #define USB_SOF_HOOK myAssemblerMacro
- * This macro (if defined) is executed in the assembler module when a
- * Start Of Frame condition is detected. It is recommended to define it to
- * the name of an assembler macro which is defined here as well so that more
- * than one assembler instruction can be used. The macro may use the register
- * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
- * immediately after an SOF pulse may be lost and must be retried by the host.
- * What can you do with this hook? Since the SOF signal occurs exactly every
- * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
- * designs running on the internal RC oscillator.
- * Please note that Start Of Frame detection works only if D- is wired to the
- * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
- */
-#define USB_CFG_CHECK_DATA_TOGGLING 0
-/* define this macro to 1 if you want to filter out duplicate data packets
- * sent by the host. Duplicates occur only as a consequence of communication
- * errors, when the host does not receive an ACK. Please note that you need to
- * implement the filtering yourself in usbFunctionWriteOut() and
- * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
- * for each control- and out-endpoint to check for duplicate packets.
- */
-#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
-/* define this macro to 1 if you want the function usbMeasureFrameLength()
- * compiled in. This function can be used to calibrate the AVR's RC oscillator.
- */
-#define USB_USE_FAST_CRC 0
-/* The assembler module has two implementations for the CRC algorithm. One is
- * faster, the other is smaller. This CRC routine is only used for transmitted
- * messages where timing is not critical. The faster routine needs 31 cycles
- * per byte while the smaller one needs 61 to 69 cycles. The faster routine
- * may be worth the 32 bytes bigger code size if you transmit lots of data and
- * run the AVR close to its limit.
- */
-
-/* -------------------------- Device Description --------------------------- */
-
-#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
-/* USB vendor ID for the device, low byte first. If you have registered your
- * own Vendor ID, define it here. Otherwise you may use one of obdev's free
- * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
- * *** IMPORTANT NOTE ***
- * This template uses obdev's shared VID/PID pair for Vendor Class devices
- * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
- * the implications!
- */
-#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
-/* This is the ID of the product, low byte first. It is interpreted in the
- * scope of the vendor ID. If you have registered your own VID with usb.org
- * or if you have licensed a PID from somebody else, define it here. Otherwise
- * you may use one of obdev's free shared VID/PID pairs. See the file
- * USB-IDs-for-free.txt for details!
- * *** IMPORTANT NOTE ***
- * This template uses obdev's shared VID/PID pair for Vendor Class devices
- * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
- * the implications!
- */
-#define USB_CFG_DEVICE_VERSION 0x00, 0x02
-/* Version number of the device: Minor number first, then major number.
- */
-#define USB_CFG_VENDOR_NAME 'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'
-#define USB_CFG_VENDOR_NAME_LEN 13
-/* These two values define the vendor name returned by the USB device. The name
- * must be given as a list of characters under single quotes. The characters
- * are interpreted as Unicode (UTF-16) entities.
- * If you don't want a vendor name string, undefine these macros.
- * ALWAYS define a vendor name containing your Internet domain name if you use
- * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
- * details.
- */
-#define USB_CFG_DEVICE_NAME 'p', 's', '2', 'a', 'v', 'r', 'G', 'B'
-#define USB_CFG_DEVICE_NAME_LEN 8
-/* Same as above for the device name. If you don't want a device name, undefine
- * the macros. See the file USB-IDs-for-free.txt before you assign a name if
- * you use a shared VID/PID.
- */
-/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */
-/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */
-/* Same as above for the serial number. If you don't want a serial number,
- * undefine the macros.
- * It may be useful to provide the serial number through other means than at
- * compile time. See the section about descriptor properties below for how
- * to fine tune control over USB descriptors such as the string descriptor
- * for the serial number.
- */
-#define USB_CFG_DEVICE_CLASS 0
-#define USB_CFG_DEVICE_SUBCLASS 0
-/* See USB specification if you want to conform to an existing device class.
- * Class 0xff is "vendor specific".
- */
-#define USB_CFG_INTERFACE_CLASS 3 /* HID */
-#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
-#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
-/* See USB specification if you want to conform to an existing device class or
- * protocol. The following classes must be set at interface level:
- * HID class is 3, no subclass and protocol required (but may be useful!)
- * CDC class is 2, use subclass 2 and protocol 1 for ACM
- */
-#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
-/* Define this to the length of the HID report descriptor, if you implement
- * an HID device. Otherwise don't define it or define it to 0.
- * If you use this define, you must add a PROGMEM character array named
- * "usbHidReportDescriptor" to your code which contains the report descriptor.
- * Don't forget to keep the array and this define in sync!
- */
-
-/* #define USB_PUBLIC static */
-/* Use the define above if you #include usbdrv.c instead of linking against it.
- * This technique saves a couple of bytes in flash memory.
- */
-
-/* ------------------- Fine Control over USB Descriptors ------------------- */
-/* If you don't want to use the driver's default USB descriptors, you can
- * provide our own. These can be provided as (1) fixed length static data in
- * flash memory, (2) fixed length static data in RAM or (3) dynamically at
- * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
- * information about this function.
- * Descriptor handling is configured through the descriptor's properties. If
- * no properties are defined or if they are 0, the default descriptor is used.
- * Possible properties are:
- * + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
- * at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
- * used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
- * you want RAM pointers.
- * + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
- * in static memory is in RAM, not in flash memory.
- * + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
- * the driver must know the descriptor's length. The descriptor itself is
- * found at the address of a well known identifier (see below).
- * List of static descriptor names (must be declared PROGMEM if in flash):
- * char usbDescriptorDevice[];
- * char usbDescriptorConfiguration[];
- * char usbDescriptorHidReport[];
- * char usbDescriptorString0[];
- * int usbDescriptorStringVendor[];
- * int usbDescriptorStringDevice[];
- * int usbDescriptorStringSerialNumber[];
- * Other descriptors can't be provided statically, they must be provided
- * dynamically at runtime.
- *
- * Descriptor properties are or-ed or added together, e.g.:
- * #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
- *
- * The following descriptors are defined:
- * USB_CFG_DESCR_PROPS_DEVICE
- * USB_CFG_DESCR_PROPS_CONFIGURATION
- * USB_CFG_DESCR_PROPS_STRINGS
- * USB_CFG_DESCR_PROPS_STRING_0
- * USB_CFG_DESCR_PROPS_STRING_VENDOR
- * USB_CFG_DESCR_PROPS_STRING_PRODUCT
- * USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
- * USB_CFG_DESCR_PROPS_HID
- * USB_CFG_DESCR_PROPS_HID_REPORT
- * USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
- *
- * Note about string descriptors: String descriptors are not just strings, they
- * are Unicode strings prefixed with a 2 byte header. Example:
- * int serialNumberDescriptor[] = {
- * USB_STRING_DESCRIPTOR_HEADER(6),
- * 'S', 'e', 'r', 'i', 'a', 'l'
- * };
- */
-
-#define USB_CFG_DESCR_PROPS_DEVICE 0
-#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
-//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0
-#define USB_CFG_DESCR_PROPS_STRINGS 0
-#define USB_CFG_DESCR_PROPS_STRING_0 0
-#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
-#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
-#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
-#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
-//#define USB_CFG_DESCR_PROPS_HID 0
-#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
-//#define USB_CFG_DESCR_PROPS_HID_REPORT 0
-#define USB_CFG_DESCR_PROPS_UNKNOWN 0
-
-#define usbMsgPtr_t unsigned short
-/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
- * a scalar type here because gcc generates slightly shorter code for scalar
- * arithmetics than for pointer arithmetics. Remove this define for backward
- * type compatibility or define it to an 8 bit type if you use data in RAM only
- * and all RAM is below 256 bytes (tiny memory model in IAR CC).
- */
-
-/* ----------------------- Optional MCU Description ------------------------ */
-
-/* The following configurations have working defaults in usbdrv.h. You
- * usually don't need to set them explicitly. Only if you want to run
- * the driver on a device which is not yet supported or with a compiler
- * which is not fully supported (such as IAR C) or if you use a differnt
- * interrupt than INT0, you may have to define some of these.
- */
-/* #define USB_INTR_CFG MCUCR */
-/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
-/* #define USB_INTR_CFG_CLR 0 */
-/* #define USB_INTR_ENABLE GIMSK */
-/* #define USB_INTR_ENABLE_BIT INT0 */
-/* #define USB_INTR_PENDING GIFR */
-/* #define USB_INTR_PENDING_BIT INTF0 */
-/* #define USB_INTR_VECTOR INT0_vect */
-
-/* Set INT1 for D- falling edge to count SOF */
-/* #define USB_INTR_CFG EICRA */
-#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
-/* #define USB_INTR_CFG_CLR 0 */
-/* #define USB_INTR_ENABLE EIMSK */
-#define USB_INTR_ENABLE_BIT INT1
-/* #define USB_INTR_PENDING EIFR */
-#define USB_INTR_PENDING_BIT INTF1
-#define USB_INTR_VECTOR INT1_vect
-
-#endif /* __usbconfig_h_included__ */
projects / qmk_firmware.git / commitdiff