Refactoring wilba.tech PCBs, updating Rama Works U80-A (#6272)

[qmk_firmware.git] / keyboards / rama / m10_b / rules.mk

diff --git a/keyboards/rama/m10_b/rules.mk b/keyboards/rama/m10_b/rules.mk
deleted file mode 100644 (file)
index 70258b9..0000000
--- a/keyboards/rama/m10_b/rules.mk
+++ /dev/null
@@ -1,68 +0,0 @@
-# project specific files
-SRC =  keyboards/wilba_tech/wt_main.c
-
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no        # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-
-RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes