-@c accidentals...
-There are some interesting points to note in this example.
-Accidentals (sharps and flats) do not have to be marked explicitly:
-you just enter the note name, and an accidental is printed
-automatically, only when necessary. Bar lines and beams are drawn
-automatically. Line breaks are calculated automatically; it does not
-matter where the lines breaks are in the source file. Finally, the
-order of time, key and clef changes is not relevant: in the printout,
-these are ordered using standard notation conventions.
-
-The example also indicates that a piece of music written in a high
-register needs lots of quotes. This makes the input less readable,
-and is also a potential source of errors.
-
-The solution is to use ``relative octave'' mode. In practice, this is
-the most convenient way to copy existing music. To use relative mode,
-add @code{\relative} before the piece of music. You must also give a
-note from which relative starts, in this case @code{c''}. If you do
-not use octavation quotes (i.e. do not add ' or , after a note),
-relative mode chooses the note that is closest to the previous one.
-@c do not use commas or quotes in this sentence
-For example: @code{c f} goes up; @code{c g} goes down:
+There are some interesting points to note in this example. Bar lines
+and beams are drawn automatically. Line breaks are calculated
+automatically; it does not matter where the line breaks are in the
+source file. Finally, the order in which time, key and clef changes are entered is not
+relevant: in the printout, these are ordered according to standard
+notation conventions.
+
+
+@cindex beams, by hand
+Beams are drawn automatically, but if you do not like where they are
+put, they can be entered by hand. Mark the first note to be beamed
+with @code{[} and the last one with @code{]}:
+@quotation
+@lilypond[fragment,relative=1,verbatim]
+a8[ ais] d[ es r d]
+@end lilypond
+@end quotation
+@separate
+
+For more information on
+@table @asis
+@item Rests
+see @ref{Rests}.
+
+@item Ties
+see @ref{Ties}.
+
+@item Accidentals
+see @ref{Accidentals}
+
+@item Key signature
+see @ref{Key signature}
+
+@item Beams
+see @ref{Beaming}
+@end table
+
+
+@node Octave entry
+@section Octave entry
+
+
+@c Tim wants to move this quotes example just before the: quotes-do not-work
+@c score, but we'd need to remove quotes from the other two (key and
+@c tie) examples...
+
+@c better to have this just before the `octaves are bad' snipped
+@c but we'd need to remove the ', from \key and tie
+To raise a note by an octave, add a high quote @code{'} (apostrophe) to
+the note name, to lower a note one octave, add a ``low quote'' @code{,}
+(a comma). Middle C is @code{c'}:
+
+@quotation
+@example
+c'4 c'' c''' \clef bass c c,
+@end example
+
+@lilypond[fragment]
+\set Score.timing = ##f
+\set Staff.TimeSignature = \turnOff
+c'4 c'' c''' \clef bass c c,
+@end lilypond
+@end quotation
+@separate
+
+An example of the use of quotes is in the following Mozart fragment:
+@lilypond[raggedright,fragment,verbatim]
+ \key a \major
+ \time 6/8
+ cis''8. d''16 cis''8 e''4 e''8
+ b'8. cis''16 b'8 d''4 d''8
+@end lilypond
+
+This example shows that music in a high register needs lots of quotes.
+This makes the input less readable, and it is a source of errors. The
+solution is to use ``relative octave'' mode. In practice, this is the
+most convenient way to copy existing music. To use relative mode, add
+@code{\relative} before the piece of music. You must also give a note
+from which relative starts, in this case @code{c''}. If you do not
+use octavation quotes (i.e. do not add @code{'} or @code{,} after a
+note), relative mode chooses the note that is closest to the previous
+one. For example, @code{c f} goes up while @code{c g} goes down: