- \override Staff.StaffSymbol #'line-positions = #'(0)
-% Shows one horizontal line. The vertical line (simulating a bar-line) is simulated with a gridline
- \set Staff.midiInstrument = #"choir aahs"
- \key c \major
- \relative c''
- {
- % disable the following line to see the the noteheads while writing the song
- \NoNoteHead
- \override NoteHead #'no-ledgers = ##t
-
- % The beam between 8th-notes is used to draw the push-line
- %How to fast write the push-lines:
- % 1. write repeatedly 'c c c c c c c c |' for the whole length of the song
- % 2. uncomment the line \NoNoteHead
- % 3. compile
- % 4. Mark the positions on which push/pull changes.
- % In the score-picture click on the position the push- or pull-part starts
- % (on the noteHead, the cursor will change to a hand-icon).
- % The cursor in the source code will jump just at this position.
- % a) If a push-part starts there, replace the 'c' by an 'e['
- % b) If a pull-part starts there, replace the 'c' by an 's'
- % 5. Switch into 'overwrite-mode' by pressing the 'ins' key.
- % 6. For the pull-parts overwrite the 'c' with 's'
- % 7. For every push-part replace the last 'c' with 'e]'
- % 8. Switch into 'insert-mode' again
- % 9. At last it should look lik e.g. (s s e[ c | c c c c c c c c | c c c c c c e] s s)
- % 10. re-enable the line \NoNoteHead
- \autoBeamOff
- \ZeroBeam
- s8 s s e[ c c c c c c e] | s s s s s
- }
+ \override Staff.StaffSymbol.line-positions = #'(0)
+ % Shows one horizontal line. The vertical line (simulating a bar-line) is simulated with a gridline
+ \set Staff.midiInstrument = #"choir aahs"
+ \key c \major
+ \relative c''
+ {
+ % disable the following line to see the the noteheads while writing the song
+ \NoNoteHead
+ \override NoteHead.no-ledgers = ##t
+
+ % The beam between 8th-notes is used to draw the push-line
+ %How to fast write the push-lines:
+ % 1. write repeatedly 'c c c c c c c c |' for the whole length of the song
+ % 2. uncomment the line \NoNoteHead
+ % 3. compile
+ % 4. Mark the positions on which push/pull changes.
+ % In the score-picture click on the position the push- or pull-part starts
+ % (on the noteHead, the cursor will change to a hand-icon).
+ % The cursor in the source code will jump just at this position.
+ % a) If a push-part starts there, replace the 'c' by an 'e['
+ % b) If a pull-part starts there, replace the 'c' by an 's'
+ % 5. Switch into 'overwrite-mode' by pressing the 'ins' key.
+ % 6. For the pull-parts overwrite the 'c' with 's'
+ % 7. For every push-part replace the last 'c' with 'e]'
+ % 8. Switch into 'insert-mode' again
+ % 9. At last it should look lik e.g. (s s e[ c | c c c c c c c c | c c c c c c e] s s)
+ % 10. re-enable the line \NoNoteHead
+ \autoBeamOff
+ \ZeroBeam
+ s8 s s e[ c c c c c c e] | s s s s s
+ }