--- /dev/null
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+# Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+# (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+# have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+# have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+# (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+# (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging,
+# with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+# bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = hhkb_tmk
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+
+# List C source files here. (C dependencies are automatically generated.)
+SRC += keymap.c \
+ matrix.c \
+ led.c
+
+CONFIG_H = config.h
+
+
+# MCU name
+#MCU = at90usb1286
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 8000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+# comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration
+MOUSEKEY_ENABLE = yes # Mouse keys
+EXTRAKEY_ENABLE = yes # Audio control and System control
+CONSOLE_ENABLE = yes # Console for debug
+COMMAND_ENABLE = yes # Commands for debug and configuration
+#NKRO_ENABLE = yes # USB Nkey Rollover
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+include $(TOP_DIR)/protocol/lufa.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk
+
+debug-on: EXTRAFLAGS += -DDEBUG
+debug-on: all
#define KEY_POWER_ON()
#define KEY_POWER_OFF()
+#elif defined(__AVR_ATmega32U4__)
+// Ports for my designed Alt Controller PCB
+// row: PB0-2
+// col: PB3-5,6
+// key: PD7(pull-uped)
+// prev: PB7
+#define KEY_INIT() do { \
+ DDRB = 0xFF; \
+ PORTB = 0x00; \
+ DDRD &= ~0x80; \
+ PORTD |= 0x80; \
+ KEY_UNABLE(); \
+ KEY_PREV_OFF(); \
+} while (0)
+#define KEY_SELECT(ROW, COL) (PORTB = (PORTB & 0xC0) | \
+ (((COL) & 0x07)<<3) | \
+ ((ROW) & 0x07))
+#define KEY_ENABLE() (PORTB &= ~(1<<6))
+#define KEY_UNABLE() (PORTB |= (1<<6))
+#define KEY_STATE() (PIND & (1<<7))
+#define KEY_PREV_ON() (PORTB |= (1<<7))
+#define KEY_PREV_OFF() (PORTB &= ~(1<<7))
+#define KEY_POWER_ON()
+#define KEY_POWER_OFF()
+
+
#elif defined(__AVR_ATmega328P__)
// Ports for V-USB
// key: PB0(pull-uped)
void matrix_init(void)
{
#ifdef DEBUG
- print_enable = true;
debug_enable = true;
debug_keyboard = true;
#endif
KEY_ENABLE();
// Wait for KEY_STATE outputs its value.
// 1us was ok on one HHKB, but not worked on another.
- _delay_us(10);
+ // no wait doesn't work on Teensy++ with pro(1us works)
+ // no wait does work on tmk PCB(8MHz) with pro2
+ // 1us wait does work on both of above
+ // 10us wait does work on Teensy++ with pro
+ // 10us wait does work on 328p+iwrap with pro
+ // 10us wait doesn't work on tmk PCB(8MHz) with pro2(very lagged scan)
+ _delay_us(1);
+// _delay_us(10);
if (KEY_STATE()) {
matrix[row] &= ~(1<<col);
} else {
projects / tmk_firmware.git / commitdiff