Adding NKRO virtual dip-switch, using existing bit in keymap byte.
[submodule "protocol/usb_hid/USB_Host_Shield_2.0"]
path = protocol/usb_hid/USB_Host_Shield_2.0
url = git@github.com:tmk/USB_Host_Shield_2.0.git
+[submodule "protocol/lufa/LUFA-git"]
+ path = protocol/lufa/LUFA-git
+ url = https://github.com/abcminiuser/lufa.git
case KC_S:
print("\n\n----- Status -----\n");
print_val_hex8(host_keyboard_leds());
+ print_val_hex8(keyboard_protocol);
+ print_val_hex8(keyboard_idle);
#ifdef PROTOCOL_PJRC
print_val_hex8(UDCON);
print_val_hex8(UDIEN);
print_val_hex8(UDINT);
print_val_hex8(usb_keyboard_leds);
- print_val_hex8(usb_keyboard_protocol);
- print_val_hex8(usb_keyboard_idle_config);
print_val_hex8(usb_keyboard_idle_count);
#endif
#ifdef NKRO_ENABLE
-bool keyboard_nkro = false;
+bool keyboard_nkro = true;
#endif
static host_driver_t *driver;
extern bool keyboard_nkro;
#endif
+uint8_t keyboard_idle;
+uint8_t keyboard_protocol;
+
/* host driver */
void host_set_driver(host_driver_t *driver);
TARGET_DIR = .
# project specific files
-SRC = keymap.c \
+SRC = keymap_common.c \
matrix.c \
led.c \
adb.c
+ifdef KEYMAP
+ SRC := keymap_$(KEYMAP).c $(SRC)
+else
+ SRC := keymap_ansi.c $(SRC)
+endif
+
CONFIG_H = config.h
TARGET_DIR = .
# keyboard dependent files
-SRC = keymap.c \
+SRC = keymap_common.c \
matrix.c \
led.c \
adb.c
+ifdef KEYMAP
+ SRC := keymap_$(KEYMAP).c $(SRC)
+else
+ SRC := keymap_ansi.c $(SRC)
+endif
+
CONFIG_H = config.h
Discuss: http://geekhack.org/showwiki.php?title=Island:14290
-Build
------
-0. Connect ADB keyboard to Teensy by 3 lines(Vcc, GND, Data). By default Data line uses port D0.
+Wiring
+------
+0. Connect ADB keyboard to Teensy by 3 lines(Vcc, GND, Data). By default Data line uses port PD0.
This converter uses AVR's internal pull-up, but it seems to be too weak, in particular when you want to use a long or coiled cable.
The external pull-up resistor(1K-10K Ohm) on Data is strongly recommended.
-1. Define following macros for ADB connection in config.h if you use other than port D0.
+1. Define following macros for ADB connection in config.h if you use other than port PD0.
ADB_PORT, ADB_PIN, ADB_DDR, ADB_DATA_BIT
2. make
3. program Teensy
+Build
+-----
+Just make
+
+ $ make clean
+ $ make
+
+If your keyboard is ISO layout
+
+ $ make KEYMAP=iso
+
+
LOCKING CAPSLOCK
----------------
Many of old ADB keyboards have mechanical push-lock switch for Capslock key and this converter supports the locking Capslock key by default. See README in top directory for more detail about this feature.
* |-----------------------------------------------------------| ,---. |---------------|
* |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | |Up | | 1| 2| 3| |
* |-----------------------------------------------------------| ,-----------. |-----------|Ent|
- * |Ctrl |Gui |Alt | Space | | | | |Lef|Dow|Rig| | 0| .| |
+ * |Ctrl |Alt |Gui | Space |Gui |Alt |Ctrl | |Lef|Dow|Rig| | 0| .| |
* `-----------------------------------------------------------' `-----------' `---------------'
*/
KEYMAP(
Notes
-----
-Many ADB keyboards has no discrimination between right modifier and left one,
+Not-extended ADB keyboards have no discrimination between right modifier and left one,
you will always see left control even if you press right control key.
-Apple Extended Keyboard and Apple Extended Keyboard II are the examples.
-Though ADB protocol itself has the ability of distinction between right and left.
-And most ADB keyboard has no NKRO functionality, though ADB protocol itself has that.
-See protocol/adb.c for more info.
+Apple Extended Keyboard and Apple Extended Keyboard II can discriminate both side
+modifiers except for GUI key(Windows/Command).
+
+And most ADB keyboard has no diodes in its matrix so they are not NKRO,
+though ADB protocol itself supports it. See protocol/adb.c for more info.
+
+If keyobard has ISO layout you need to use ISO keymap with `make KEYMAP=iso`. With ANSI
+keymap you will suffer from swapped keys problem.
+
+https://github.com/tmk/tmk_keyboard/issues/35
EOF
+++ /dev/null
-/*
-Copyright 2011 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-/*
- * Keymap for ADB keyboard
- */
-#include <stdint.h>
-#include <stdbool.h>
-#include <avr/pgmspace.h>
-#include "keycode.h"
-#include "print.h"
-#include "debug.h"
-#include "util.h"
-#include "keymap.h"
-
-
-#define KEYCODE(layer, row, col) (pgm_read_byte(&keymaps[(layer)][(row)][(col)]))
-
-#define KEYMAP_ALL( \
- K35, K7A,K78,K63,K76, K60,K61,K62,K64, K65,K6D,K67,K6F, K69,K6B,K71, K7F, \
- K32,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33, K72,K73,K74, K47,K51,K4B,K43, \
- K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E,K2A, K75,K77,K79, K59,K5B,K5C,K4E, \
- K39,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27, K24, K56,K57,K58,K45, \
- K38,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C, K7B, K3E, K53,K54,K55, \
- K36,K3A,K37, K31, K7C,K7D, K3B,K3D,K3C, K52, K41,K4C, \
- /* for ISO/JIS keyboard */ \
- K0A, /* NON-US \ and | 0x64 */ \
- K34, /* Keypad ENTER 0x58 */ \
- K40, /* F17 0x6C */ \
- K44, /* F18? 0x6d */ \
- K4F, /* F18 0x6d */ \
- K50, /* F19 0x6e */ \
- K5A, /* F20 0x6f */ \
- K5D, /* INTL3(Yen) 0x89 */ \
- K5E, /* INTL1(Ro) 0x87 */ \
- K5F, /* Keypad Comma 0x85 */ \
- K66, /* LANG2(Eisu) 0x91 */ \
- K68, /* LANG1(Kana) 0x90 */ \
- K6A, /* F16 0x6B */ \
- K6E /* Application 0x65 */ \
-) { \
- { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07 }, \
- { KC_##K08, KC_##K09, KC_##K0A, KC_##K0B, KC_##K0C, KC_##K0D, KC_##K0E, KC_##K0F }, \
- { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
- { KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D, KC_##K1E, KC_##K1F }, \
- { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27 }, \
- { KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D, KC_##K2E, KC_##K2F }, \
- { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37 }, \
- { KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D, KC_##K3E, KC_NO }, \
- { KC_##K40, KC_##K41, KC_NO, KC_##K43, KC_##K44, KC_##K45, KC_NO, KC_##K47 }, \
- { KC_NO, KC_NO, KC_NO, KC_##K4B, KC_##K4C, KC_NO, KC_##K4E, KC_##K4F }, \
- { KC_##K50, KC_##K51, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57 }, \
- { KC_##K58, KC_##K59, KC_##K5A, KC_##K5B, KC_##K5C, KC_##K5D, KC_##K5E, KC_##K5F }, \
- { KC_##K60, KC_##K61, KC_##K62, KC_##K63, KC_##K64, KC_##K65, KC_##K66, KC_##K67 }, \
- { KC_##K68, KC_##K69, KC_##K6A, KC_##K6B, KC_NO, KC_##K6D, KC_##K6E, KC_##K6F }, \
- { KC_NO, KC_##K71, KC_##K72, KC_##K73, KC_##K74, KC_##K75, KC_##K76, KC_##K77 }, \
- { KC_##K78, KC_##K79, KC_##K7A, KC_##K7B, KC_##K7C, KC_##K7D, KC_NO, KC_##K7F } \
-}
-
-/* Apple Extended Keyboard US
- * ,---. ,---------------. ,---------------. ,---------------. ,-----------. ,---.
- * |Esc| |F1 |F2 |F3 |F4 | |F5 |F6 |F7 |F8 | |F9 |F10|F11|F12| |PrS|ScL|Pau| |Pwr|
- * `---' `---------------' `---------------' `---------------' `-----------' `---'
- * ,-----------------------------------------------------------. ,-----------. ,---------------.
- * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backspa| |Ins|Hom|PgU| |NmL| =| /| *|
- * |-----------------------------------------------------------| |-----------| |---------------|
- * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| |Del|End|PgD| | 7| 8| 9| -|
- * |-----------------------------------------------------------| `-----------' |---------------|
- * |CapsLo| A| S| D| F| G| H| J| K| L| ;| '|Return | | 4| 5| 6| +|
- * |-----------------------------------------------------------| ,---. |---------------|
- * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | |Up | | 1| 2| 3| |
- * |-----------------------------------------------------------| ,-----------. |-----------|Ent|
- * |Ctrl |Opt |Cmd | Space | |Opt |Ctrl | |Lef|Dow|Rig| | 0| .| |
- * `-----------------------------------------------------------' `-----------' `---------------'
- */
-#define KEYMAP_EXTENDED_US( \
- K35, K7A,K78,K63,K76, K60,K61,K62,K64, K65,K6D,K67,K6F, K69,K6B,K71, K7F, \
- K32,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33, K72,K73,K74, K47,K51,K4B,K43, \
- K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E,K2A, K75,K77,K79, K59,K5B,K5C,K4E, \
- K39,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27, K24, K56,K57,K58,K45, \
- K38,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C, K7B, K3E, K53,K54,K55, \
- K36,K3A,K37, K31, K7C,K7D, K3B,K3D,K3C, K52, K41,K4C \
-) KEYMAP_ALL( \
- K35, K7A,K78,K63,K76, K60,K61,K62,K64, K65,K6D,K67,K6F, K69,K6B,K71, K7F, \
- K32,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33, K72,K73,K74, K47,K51,K4B,K43, \
- K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E,K2A, K75,K77,K79, K59,K5B,K5C,K4E, \
- K39,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27, K24, K56,K57,K58,K45, \
- K38,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C, K7B, K3E, K53,K54,K55, \
- K36,K3A,K37, K31, K7C,K7D, K3B,K3D,K3C, K52, K41,K4C, \
- /* for ISO/JIS keyboard */ \
- NONUS_BSLASH, /* NON-US \ and | 0x64 */ \
- KP_ENTER, /* Keypad ENTER 0x58 */ \
- F17, /* F17 0x6C */ \
- F18, /* F18? 0x6d */ \
- F18, /* F18 0x6d */ \
- F19, /* F19 0x6e */ \
- F20, /* F20 0x6f */ \
- INT3, /* INTL3(Yen) 0x89 */ \
- INT1, /* INTL1(Ro) 0x87 */ \
- KP_COMMA, /* Keypad Comma 0x85 */ \
- LANG2, /* LANG2(Eisu) 0x91 */ \
- LANG1, /* LANG1(Kana) 0x90 */ \
- F16, /* F16 0x6B */ \
- APPLICATION /* Application 0x65 */ \
-)
-
-/* M0116
-* +-------+
-* | power |
-* +-------+
-* +---+---+---+---+---+---+---+---+---+---+---+---+---+-----+ +---+---+---+---+
-* |esc| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | bks | |clr| = | / | * |
-* +---------------------------------------------------------+ +---+---+---+---+
-* | tab | q | w | e | r | t | y | u | i | o | p | [ | ] | | | 7 | 8 | 9 | + |
-* +-----------------------------------------------------+ | +---+---+---+---+
-* | ctrl | a | s | d | f | g | h | j | k | l | ; | ' |return| | 4 | 5 | 6 | - |
-* +---------------------------------------------------------+ +---+---+---+---+
-* | shift | z | x | c | v | b | n | m | , | . | / | shift | | 1 | 2 | 3 | |
-* +---------------------------------------------------------+ +-------+---|ent|
-* |cap|opt|comnd| ` | | \ |lef|rig|dwn|up | | 0 | . | |
-* +---------------------------------------------------------+ +-------+---+---+
-*/
-#define KEYMAP_M0116( \
- K7F, \
- K35,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33, K47,K51,K4B,K43, \
- K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E, K59,K5B,K5C,K45, \
- K36,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27, K24, K56,K57,K58,K4E, \
- K38,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C, K7B, K53,K54,K55, \
- K39,K3A,K37,K32, K31, K2A,K3B,K3C,K3D,K3E, K52, K41,K4C \
-) { \
- { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07 }, \
- { KC_##K08, KC_##K09, KC_NO, KC_##K0B, KC_##K0C, KC_##K0D, KC_##K0E, KC_##K0F }, \
- { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
- { KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D, KC_##K1E, KC_##K1F }, \
- { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27 }, \
- { KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D, KC_##K2E, KC_##K2F }, \
- { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_NO, KC_##K35, KC_##K36, KC_##K37 }, \
- { KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D, KC_##K3E, KC_NO }, \
- { KC_NO, KC_##K41, KC_NO, KC_##K43, KC_NO, KC_##K45, KC_NO, KC_##K47 }, \
- { KC_NO, KC_NO, KC_NO, KC_##K4B, KC_##K4C, KC_NO, KC_##K4E, KC_NO }, \
- { KC_NO, KC_##K51, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57 }, \
- { KC_##K58, KC_##K59, KC_NO, KC_##K5B, KC_##K5C, KC_NO, KC_NO, KC_NO }, \
- { KC_NO, KC_NO, KC_NO, KC_NO , KC_NO, KC_NO, KC_NO, KC_NO }, \
- { KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \
- { KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \
- { KC_NO , KC_NO, KC_NO , KC_##K7B, KC_NO, KC_NO, KC_NO, KC_##K7F } \
-}
-
-
-// Assign Fn key(0-7) to a layer to which switch with the Fn key pressed.
-static const uint8_t PROGMEM fn_layer[] = {
- 0, // Fn0
- 0, // Fn1
- 0, // Fn2
- 0, // Fn3
- 0, // Fn4
- 0, // Fn5
- 0, // Fn6
- 0 // Fn7
-};
-
-// Assign Fn key(0-7) to a keycode sent when release Fn key without use of the layer.
-// See layer.c for details.
-static const uint8_t PROGMEM fn_keycode[] = {
- KC_NO, // Fn0
- KC_NO, // Fn1
- KC_NO, // Fn2
- KC_NO, // Fn3
- KC_NO, // Fn4
- KC_NO, // Fn5
- KC_NO, // Fn6
- KC_NO // Fn7
-};
-
-static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
- KEYMAP_EXTENDED_US(
- ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, PSCR,SLCK,PAUS, PWR,
- GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, INS, HOME,PGUP, NLCK,PEQL,PSLS,PAST,
- TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,BSLS, DEL, END, PGDN, P7, P8, P9, PMNS,
- LCAP,A, S, D, F, G, H, J, K, L, SCLN,QUOT, ENT, P4, P5, P6, PPLS,
- LSFT,Z, X, C, V, B, N, M, COMM,DOT, SLSH, RSFT, UP, P1, P2, P3,
- LCTL,LGUI,LALT, SPC, RGUI,RCTL, LEFT,DOWN,RGHT, P0, PDOT,PENT
- ),
-};
-
-
-uint8_t keymap_get_keycode(uint8_t layer, uint8_t row, uint8_t col)
-{
- return KEYCODE(layer, row, col);
-}
-
-uint8_t keymap_fn_layer(uint8_t index)
-{
- return pgm_read_byte(&fn_layer[index]);
-}
-
-uint8_t keymap_fn_keycode(uint8_t index)
-{
- return pgm_read_byte(&fn_keycode[index]);
-}
--- /dev/null
+#include "keymap_common.h"
+
+
+const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ KEYMAP_EXT_ANSI(
+ ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, PSCR,SLCK,PAUS, PWR,
+ GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, INS, HOME,PGUP, NLCK,PEQL,PSLS,PAST,
+ TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,BSLS, DEL, END, PGDN, P7, P8, P9, PMNS,
+ LCAP,A, S, D, F, G, H, J, K, L, SCLN,QUOT, ENT, P4, P5, P6, PPLS,
+ LSFT,Z, X, C, V, B, N, M, COMM,DOT, SLSH, RSFT, UP, P1, P2, P3,
+ LCTL,LALT,LGUI, SPC, RALT,RCTL, LEFT,DOWN,RGHT, P0, PDOT,PENT
+ ),
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+};
--- /dev/null
+/*
+Copyright 2011,2012,2013 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+#include "keymap_common.h"
+
+
+/* translates key to keycode */
+uint8_t keymap_key_to_keycode(uint8_t layer, key_t key)
+{
+ return pgm_read_byte(&keymaps[(layer)][(key.row)][(key.col)]);
+}
+
+/* translates Fn keycode to action */
+action_t keymap_fn_to_action(uint8_t keycode)
+{
+ return (action_t){ .code = pgm_read_word(&fn_actions[FN_INDEX(keycode)]) };
+}
--- /dev/null
+/*
+Copyright 2011,2012,2013 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+#ifndef KEYMAP_COMMON_H
+#define KEYMAP_COMMON_H
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <avr/pgmspace.h>
+#include "keycode.h"
+#include "action.h"
+#include "action_macro.h"
+#include "report.h"
+#include "print.h"
+#include "debug.h"
+#include "keymap.h"
+
+
+extern const uint8_t keymaps[][MATRIX_ROWS][MATRIX_COLS];
+extern const uint16_t fn_actions[];
+
+
+/* M0115 Apple Extended Keyboard ANSI
+ * ,---. ,---------------. ,---------------. ,---------------. ,-----------. ,---.
+ * |Esc| |F1 |F2 |F3 |F4 | |F5 |F6 |F7 |F8 | |F9 |F10|F11|F12| |PrS|ScL|Pau| |Pwr|
+ * `---' `---------------' `---------------' `---------------' `-----------' `---'
+ * ,-----------------------------------------------------------. ,-----------. ,---------------.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backspa| |Ins|Hom|PgU| |NmL| =| /| *|
+ * |-----------------------------------------------------------| |-----------| |---------------|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| |Del|End|PgD| | 7| 8| 9| -|
+ * |-----------------------------------------------------------| `-----------' |---------------|
+ * |CapsLo| A| S| D| F| G| H| J| K| L| ;| '|Return | | 4| 5| 6| +|
+ * |-----------------------------------------------------------| ,---. |---------------|
+ * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | |Up | | 1| 2| 3| |
+ * |-----------------------------------------------------------| ,-----------. |-----------|Ent|
+ * |Ctrl |Opt |Cmd | Space | |Opt |Ctrl | |Lef|Dow|Rig| | 0| .| |
+ * `-----------------------------------------------------------' `-----------' `---------------'
+ */
+#define KEYMAP_EXT_ANSI( \
+ K35, K7A,K78,K63,K76, K60,K61,K62,K64, K65,K6D,K67,K6F, K69,K6B,K71, K7F, \
+ K32,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33, K72,K73,K74, K47,K51,K4B,K43, \
+ K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E,K2A, K75,K77,K79, K59,K5B,K5C,K4E, \
+ K39,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27, K24, K56,K57,K58,K45, \
+ K38,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C, K7B, K3E, K53,K54,K55, \
+ K36,K3A,K37, K31, K7C,K7D, K3B,K3D,K3C, K52, K41,K4C \
+) { \
+ { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07 }, \
+ { KC_##K08, KC_##K09, KC_NUBS, KC_##K0B, KC_##K0C, KC_##K0D, KC_##K0E, KC_##K0F }, \
+ { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
+ { KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D, KC_##K1E, KC_##K1F }, \
+ { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27 }, \
+ { KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D, KC_##K2E, KC_##K2F }, \
+ { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_PENT, KC_##K35, KC_##K36, KC_##K37 }, \
+ { KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D, KC_##K3E, KC_NO }, \
+ { KC_F17, KC_##K41, KC_NO, KC_##K43, KC_F18, KC_##K45, KC_NO, KC_##K47 }, \
+ { KC_NO, KC_NO, KC_NO, KC_##K4B, KC_##K4C, KC_NO, KC_##K4E, KC_F18 }, \
+ { KC_F19, KC_##K51, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57 }, \
+ { KC_##K58, KC_##K59, KC_F20, KC_##K5B, KC_##K5C, KC_INT3, KC_INT1, KC_PCMM }, \
+ { KC_##K60, KC_##K61, KC_##K62, KC_##K63, KC_##K64, KC_##K65, KC_LANG2, KC_##K67 }, \
+ { KC_LANG1, KC_##K69, KC_F16, KC_##K6B, KC_NO, KC_##K6D, KC_APP, KC_##K6F }, \
+ { KC_NO, KC_##K71, KC_##K72, KC_##K73, KC_##K74, KC_##K75, KC_##K76, KC_##K77 }, \
+ { KC_##K78, KC_##K79, KC_##K7A, KC_##K7B, KC_##K7C, KC_##K7D, KC_NO, KC_##K7F } \
+}
+
+/* M0115 Apple Extended Keyboard ISO
+ * ,---. ,---------------. ,---------------. ,---------------. ,-----------. ,---.
+ * |Esc| |F1 |F2 |F3 |F4 | |F5 |F6 |F7 |F8 | |F9 |F10|F11|F12| |PrS|ScL|Pau| |Pwr|
+ * `---' `---------------' `---------------' `---------------' `-----------' `---'
+ * ,-----------------------------------------------------------. ,-----------. ,---------------.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backspa| |Ins|Hom|PgU| |NmL| =| /| *|
+ * |-----------------------------------------------------------| |-----------| |---------------|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]|Retur| |Del|End|PgD| | 7| 8| 9| -|
+ * |------------------------------------------------------` | `-----------' |---------------|
+ * |CapsLo| A| S| D| F| G| H| J| K| L| ;| '| #| | | 4| 5| 6| +|
+ * |-----------------------------------------------------------| ,---. |---------------|
+ * |Shif| \| Z| X| C| V| B| N| M| ,| ,| /|Shift | |Up | | 1| 2| 3| |
+ * |-----------------------------------------------------------| ,-----------. |-----------|Ent|
+ * |Ctrl |Opt |Cmd | Space | |Opt |Ctrl | |Lef|Dow|Rig| | 0| .| |
+ * `-----------------------------------------------------------' `-----------' `---------------'
+ */
+#define KEYMAP_EXT_ISO( \
+ K35, K7A,K78,K63,K76, K60,K61,K62,K64, K65,K6D,K67,K6F, K69,K6B,K71, K7F, \
+ K32,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33, K72,K73,K74, K47,K51,K4B,K43, \
+ K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E,K24, K75,K77,K79, K59,K5B,K5C,K4E, \
+ K39,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27,K2A, K56,K57,K58,K45, \
+ K38,K0A,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C, K7B, K3E, K53,K54,K55, \
+ K36,K3A,K37, K31, K7C,K7D, K3B,K3D,K3C, K52, K41,K4C \
+) { \
+ { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07 }, \
+ { KC_##K08, KC_##K09, KC_##K0A, KC_##K0B, KC_##K0C, KC_##K0D, KC_##K0E, KC_##K0F }, \
+ { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
+ { KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D, KC_##K1E, KC_##K1F }, \
+ { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27 }, \
+ { KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D, KC_##K2E, KC_##K2F }, \
+ { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_PENT, KC_##K35, KC_##K36, KC_##K37 }, \
+ { KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D, KC_##K3E, KC_NO }, \
+ { KC_F17, KC_##K41, KC_NO, KC_##K43, KC_F18, KC_##K45, KC_NO, KC_##K47 }, \
+ { KC_NO, KC_NO, KC_NO, KC_##K4B, KC_##K4C, KC_NO, KC_##K4E, KC_F18 }, \
+ { KC_F19, KC_##K51, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57 }, \
+ { KC_##K58, KC_##K59, KC_F20, KC_##K5B, KC_##K5C, KC_INT3, KC_INT1, KC_PCMM }, \
+ { KC_##K60, KC_##K61, KC_##K62, KC_##K63, KC_##K64, KC_##K65, KC_LANG2, KC_##K67 }, \
+ { KC_LANG1, KC_##K69, KC_F16, KC_##K6B, KC_NO, KC_##K6D, KC_APP, KC_##K6F }, \
+ { KC_NO, KC_##K71, KC_##K72, KC_##K73, KC_##K74, KC_##K75, KC_##K76, KC_##K77 }, \
+ { KC_##K78, KC_##K79, KC_##K7A, KC_##K7B, KC_##K7C, KC_##K7D, KC_NO, KC_##K7F } \
+}
+
+
+
+
+/* M0116 Apple Standard Keyboard ANSI
+* +-------+
+* | power |
+* +-------+
+* +---+---+---+---+---+---+---+---+---+---+---+---+---+-----+ +---+---+---+---+
+* |esc| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | bks | |clr| = | / | * |
+* +---------------------------------------------------------+ +---+---+---+---+
+* | tab | q | w | e | r | t | y | u | i | o | p | [ | ] | | | 7 | 8 | 9 | + |
+* +-----------------------------------------------------+ | +---+---+---+---+
+* | ctrl | a | s | d | f | g | h | j | k | l | ; | ' |return| | 4 | 5 | 6 | - |
+* +---------------------------------------------------------+ +---+---+---+---+
+* | shift | z | x | c | v | b | n | m | , | . | / | shift | | 1 | 2 | 3 | |
+* +---------------------------------------------------------+ +-------+---|ent|
+* |cap|opt|comnd| ` | | \ |lef|rig|dwn|up | | 0 | . | |
+* +---------------------------------------------------------+ +-------+---+---+
+*/
+#define KEYMAP_M0116_ANSI( \
+ K7F, \
+ K35,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33, K47,K51,K4B,K43, \
+ K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E, K59,K5B,K5C,K45, \
+ K36,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27, K24, K56,K57,K58,K4E, \
+ K38,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C, K7B, K53,K54,K55, \
+ K39,K3A,K37,K32, K31, K2A,K3B,K3C,K3D,K3E, K52, K41,K4C \
+) { \
+ { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07 }, \
+ { KC_##K08, KC_##K09, KC_NO, KC_##K0B, KC_##K0C, KC_##K0D, KC_##K0E, KC_##K0F }, \
+ { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
+ { KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D, KC_##K1E, KC_##K1F }, \
+ { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27 }, \
+ { KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D, KC_##K2E, KC_##K2F }, \
+ { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_NO, KC_##K35, KC_##K36, KC_##K37 }, \
+ { KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D, KC_##K3E, KC_NO }, \
+ { KC_NO, KC_##K41, KC_NO, KC_##K43, KC_NO, KC_##K45, KC_NO, KC_##K47 }, \
+ { KC_NO, KC_NO, KC_NO, KC_##K4B, KC_##K4C, KC_NO, KC_##K4E, KC_NO }, \
+ { KC_NO, KC_##K51, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57 }, \
+ { KC_##K58, KC_##K59, KC_NO, KC_##K5B, KC_##K5C, KC_NO, KC_NO, KC_NO }, \
+ { KC_NO, KC_NO, KC_NO, KC_NO , KC_NO, KC_NO, KC_NO, KC_NO }, \
+ { KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \
+ { KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \
+ { KC_NO , KC_NO, KC_NO , KC_##K7B, KC_NO, KC_NO, KC_NO, KC_##K7F } \
+}
+
+#endif
+
+
+/*
+ADB ANSI/ISO Keymapping Note
+============================
+ANSI
+,----------- ----------.
+| *a| 1| 2 =|Backspa|
+|----------- ----------|
+|Tab | Q| | ]| *c|
+|----------- ----------|
+|CapsLo| A| '|Return |
+|----------- ----------|
+|Shift | Shift |
+`----------- ----------'
+
+ISO
+,----------- ----------.
+| *a| 1| 2 =|Backspa|
+|----------- ----------|
+|Tab | Q| | ]|Retur|
+|----------- -----` |
+|CapsLo| A| '| *c| |
+|----------- ----------|
+|Shif| *b| Shift |
+`----------- ----------'
+
+ADB Keyboard scan code:
+ ADB scan code USB usage
+ ------------- ---------
+Key ANSI ISO ANSI ISO
+---------------------------------------------
+*a 0x32 0x0A 0x35 0x35
+*b ---- 0x32 ---- 0x64
+*c 0x2A 0x2A 0x31 0x31(or 0x32)
+
+
+TMK ADB-USB mapping:
+ADB USB(ANSI) USB(ISO)
+---------------------------------
+0x32 0x35 0x64
+0x0A ---- 0x35
+0x2A 0x31 0x31(or 0x32)
+
+Note that mappings of ADB code 0x32 are diffrent between ANSI and ISO keyboard.
+https://github.com/tmk/tmk_keyboard/issues/35
+ */
--- /dev/null
+#include "keymap_common.h"
+
+
+const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ /* Default Layer: plain keymap
+ * ,---. ,---------------. ,---------------. ,---------------. ,-----------. ,---.
+ * |Esc| |F1 |F2 |F3 |F4 | |F5 |F6 |F7 |F8 | |F9 |F10|F11|F12| |PrS|ScL|Pau| | |
+ * `---' `---------------' `---------------' `---------------' `-----------' `---'
+ * ,-----------------------------------------------------------. ,-----------. ,---------------.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backspa| |Ins|Hom|PgU| |NmL| =| /| *|
+ * |-----------------------------------------------------------| |-----------| |---------------|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| Fn0| |Del|End|PgD| | 7| 8| 9| -|
+ * |-----------------------------------------------------------| `-----------' |---------------|
+ * |CapsLo| A| S| D| F| G| H| J| K| L| ;| '|Return | | 4| 5| 6| +|
+ * |-----------------------------------------------------------| ,---. |---------------|
+ * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | |Up | | 1| 2| 3| |
+ * |-----------------------------------------------------------| ,-----------. |-----------|Ent|
+ * |Ctrl |Gui |Alt | Space |Alt |Gui |Ctrl | |Lef|Dow|Rig| | 0| .| |
+ * `-----------------------------------------------------------' `-----------' `---------------'
+ */
+ KEYMAP_EXT_ANSI(
+ ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, PSCR,SLCK,BRK, NO,
+ GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, INS, HOME,PGUP, NLCK,EQL, PSLS,PAST,
+ TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,FN0, DEL, END, PGDN, P7, P8, P9, PMNS,
+ CAPS,A, S, D, F, G, H, J, K, L, SCLN,QUOT, ENT, P4, P5, P6, PPLS,
+ LSFT,Z, X, C, V, B, N, M, COMM,DOT, SLSH, RSFT, UP, P1, P2, P3,
+ LCTL,LGUI,LALT, SPC, RGUI,RCTL, LEFT,DOWN,RGHT, P0, PDOT,PENT
+ ),
+
+ /* Default Layer: plain keymap
+ * ,---. ,---------------. ,---------------. ,---------------. ,-----------. ,---.
+ * |` | |F1 |F2 |F3 |F4 | |F5 |F6 |F7 |F8 | |F9 |F10|F11|F12| |PrS|ScL|Pau| | |
+ * `---' `---------------' `---------------' `---------------' `-----------' `---'
+ * ,-----------------------------------------------------------. ,-----------. ,---------------.
+ * |Esc|F1 |F2 |F3 |F4 |F5 |F6 |F7 |F8 |F9 |F10|F11|F12|Delete | |Ins|Hom|PgU| |NmL|Mb1|Mb2|Mb3|
+ * |-----------------------------------------------------------| |-----------| |---------------|
+ * |Tab | Q| W| E| R| T| Y| U|PrS|ScL|Pau|Up |Ins| Fn0| |Del|End|PgD| |MwD|McU|MwU|MwD|
+ * |-----------------------------------------------------------| `-----------' |---------------|
+ * |CapsLo|VoD|VoU|Mut| F| G| H| J|Hom|PgU|Lef|Rig|Return | |McL|McD|McR|MwU|
+ * |-----------------------------------------------------------| ,---. |---------------|
+ * |Shift | Z| X| C| V| B| N| M|End|PgD|Dow|Shift | |PgU| |MwL|McD|MwR| |
+ * |-----------------------------------------------------------| ,-----------. |-----------|Mb3|
+ * |Ctrl |Gui |Alt | Space |Alt |Gui |Ctrl | |Hom|PgD|End| | Mb1|Mb2| |
+ * `-----------------------------------------------------------' `-----------' `---------------'
+ */
+ KEYMAP_EXT_ANSI(
+ GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, PSCR,SLCK,BRK, NO,
+ ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, INS, HOME,PGUP, NLCK,BTN1,BTN2,BTN3,
+ TAB, Q, W, E, R, T, Y, U, PSCR,SLCK,PAUS,UP, INS, FN0, DEL, END, PGDN, WH_D,MS_U,WH_U,WH_D,
+ CAPS,VOLD,VOLU,MUTE,F, G, H, J, HOME,PGUP,LEFT,RGHT, ENT, MS_L,MS_D,MS_R,WH_U,
+ LSFT,Z, X, C, V, B, N, M, END, PGDN,DOWN, RSFT, PGUP, WH_L,MS_D,WH_R,
+ LCTL,LGUI,LALT, SPC, RGUI,RCTL, HOME,PGDN,END, BTN1, BTN2,BTN3
+ ),
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+ [0] = ACTION_LAYER_TAP_KEY(1, KC_BSLS),
+};
--- /dev/null
+#include "keymap_common.h"
+
+
+const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ KEYMAP_EXT_ISO(
+ ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, PSCR,SLCK,PAUS, PWR,
+ GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, INS, HOME,PGUP, NLCK,PEQL,PSLS,PAST,
+ TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,ENT, DEL, END, PGDN, P7, P8, P9, PMNS,
+ LCAP,A, S, D, F, G, H, J, K, L, SCLN,QUOT,NUHS, P4, P5, P6, PPLS,
+ LSFT,NUBS,Z, X, C, V, B, N, M, COMM,DOT, SLSH, RSFT, UP, P1, P2, P3,
+ LCTL,LALT,LGUI, SPC, RALT,RCTL, LEFT,DOWN,RGHT, P0, PDOT,PENT
+ ),
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+};
# keyboard dependent files
SRC = matrix.c \
led.c \
+ keymap_common.c \
m0110.c
# To use own keymap file run make like: make keymap=hasu
-ifdef keymap
- SRC += keymap_$(keymap).c
+ifdef KEYMAP
+ SRC += keymap_$(KEYMAP).c
else
- SRC += keymap.c
+ SRC += keymap_plain.c
endif
CONFIG_H = config.h
# Build Options
# *Comment out* to disable the options.
#
-BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
-KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
+#KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
======================================
This firmware converts the protocol of Apple Macintosh keyboard **M0110**, **M0110A** and **M0120** into USB. Target of this project is USB AVR controller **ATmega32U4**. Using this converter you can revive these retro keyboards with modern computer.
+Read README of top directory too.
+
Pictures of **M0110 + M0120** and **M0110A**.
------
- 2013/08: Change port for signals `PF` to `PD`
- 2013/09: Change port again, it uses inversely `PD0` for data and `PD1` for clock line now.
+- 2014/06: Change keymaps
$ git clone git://github.com/tmk/tmk_keyboard.git (or download source)
$ cd m0110_usb
- $ make -f Makefile clean
- $ make -f Makefile
+ $ make clean
+ $ make
+
+To select keymap use `KEYMAP` option.
-and program your Teensy with [PJRC Teensy loader](http://www.pjrc.com/teensy/loader.html).
+ $ make clean
+ $ make KEYMAP={plain|spacefn|hasu}
Keymap
------
-You can change keymaps by editing *keymap.c*.
-
-### M0110 & M0120
-#### *Default Layer*
- ,---------------------------------------------------------. ,---------------.
- | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Clr| -|Lft|Rgt|
- |---------------------------------------------------------| |---------------|
- |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| | 7| 8| 9| Up|
- |---------------------------------------------------------| |---------------|
- |Caps | A| S| D| F| G| H| J| K| L| ;| '|Enter | | 4| 5| 6| Dn|
- |---------------------------------------------------------| |---------------|
- |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | | 1| 2| 3| |
- `---------------------------------------------------------' |-----------|Ent|
- |Ctl|Gui | Space |Alt |Ctl| | 0| .| |
- `-----------------------------------------------' `---------------'
-
-- `Space` and `Enter` also work as `Fn` layer switch key when holding down.
-
-#### *Function Layer(WASD/HHKB)*
- ,---------------------------------------------------------. ,---------------.
- |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delet| |Nlk| -|Lft|Rgt|
- |---------------------------------------------------------| |---------------|
- |Caps |Hom| Up|PgU| | | | |Psc|Slk|Pau|Up |Ins| \| | 7| 8| 9| Up|
- |---------------------------------------------------------| |---------------|
- |Caps |Lef|Dow|Rig| | | | |Hom|PgU|Lef|Rig|Enter | | 4| 5| 6| Dn|
- |---------------------------------------------------------| |---------------|
- |Shift |End| |PgD| | | | |End|PgD|Dow|Shift | | 1| 2| 3| |
- `---------------------------------------------------------' |-----------|Ent|
- |Ctl|Gui | Space |Alt |Ctl| | 0| .| |
- `-----------------------------------------------' `---------------'
-
-
-### M0110A
-#### *Default Layer*
- ,---------------------------------------------------------. ,---------------.
- | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Clr| =| /| *|
- |---------------------------------------------------------| |---------------|
- |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -|
- |-----------------------------------------------------' | |---------------|
- |Caps | A| S| D| F| G| H| J| K| L| ;| '|Enter | | 4| 5| 6| +|
- |---------------------------------------------------------| |---------------|
- |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft| Up| | 1| 2| 3| |
- |---------------------------------------------------------| |-----------|Ent|
- |Ctrl |Gui | Space | \|Lft|Rgt|Dwn| | 0| .| |
- `---------------------------------------------------------' `---------------'
-
-- `Space` and `Enter` also work as `Fn` layer switch key when holding down.
-- `Backslash(\)` also works as `Alt` when holding down.
-
-#### *Function Layer(WASD/HHKB)*
- ,---------------------------------------------------------. ,---------------.
- |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delet| |Nlk| =| /| *|
- |---------------------------------------------------------| |---------------|
- |Caps |Hom| Up|PgU| | | | |Psc|Slk|Pau|Up |Ins| | | 7| 8| 9| -|
- |-----------------------------------------------------' | |---------------|
- |Caps |Lef|Dow|Rig| | | | |Hom|PgU|Lef|Rig|Enter | | 4| 5| 6| +|
- |---------------------------------------------------------| |---------------|
- |Shift |End| |PgD| | | | |End|PgD|Dow|Shif|PgU| | 1| 2| 3| |
- |---------------------------------------------------------| |-----------|Ent|
- |Ctrl |Gui | Space | \|Hom|End|PgD| | 0| .| |
- `---------------------------------------------------------' `---------------'
+To create your own keymap copy existent keymap file to `keymap_name.c` and edit it. You can build it like this.
+
+ $ make clean
+ $ make KEYMAP=name
--- /dev/null
+/*
+Copyright 2011,2012,2014 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+#include <stdint.h>
+#include <avr/pgmspace.h>
+#include "action.h"
+#include "keycode.h"
+#include "keymap.h"
+#include "keymap_common.h"
+
+
+/* translates key to keycode */
+uint8_t keymap_key_to_keycode(uint8_t layer, key_t key)
+{
+ return pgm_read_byte(&keymaps[(layer)][(key.row)][(key.col)]);
+}
+
+/* translates Fn index to action */
+action_t keymap_fn_to_action(uint8_t keycode)
+{
+ action_t action;
+ action.code = pgm_read_word(&fn_actions[FN_INDEX(keycode)]);
+ return action;
+}
--- /dev/null
+/*
+Copyright 2011,2012,2014 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+#include <stdint.h>
+#include <avr/pgmspace.h>
+#include "keycode.h"
+#include "keymap.h"
+
+
+extern const uint8_t keymaps[][MATRIX_ROWS][MATRIX_COLS];
+extern const uint16_t fn_actions[];
+
+
+/*
+ * The keymap works with both M0110 and M0110A keyboards. As you can see, the M0110A is a superset
+ * of the M0110 keyboard, with only one exception: 'Enter' in M0110 does not exist
+ * on the M0110A, but since it generates a unique scan code which is not used for some other key in
+ * the M0110A, they are totally interchangeable. In fact, the M0110A is functionally (almost)
+ * identical to the combination of the M0110 along with the M0120 keypad. The only difference
+ * (which is causing some problems as you will read below) is that the M0110+M0120 don't have
+ * dedicated arrow keys, while the M0110A does. However, the M0120 did have arrow keys, which
+ * doubled as the [comma], [/], [*] and [+] keys, when used with the [Shift] key. The M0110A has
+ * substituted the [comma] key with the [=] key, however its scancode is the same.
+ *
+ * Physical layout:
+ * M0110A
+ * ,---------------------------------------------------------. ,---------------.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Bcksp| |Clr| =| /| *|
+ * |---------------------------------------------------------| |---------------|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -|
+ * |-----------------------------------------------------' | |---------------|
+ * |Caps | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| +|
+ * |---------------------------------------------------------| |---------------|
+ * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| |
+ * |---------------------------------------------------------' |-----------|Ent|
+ * |Opt |Mac | Space | \|Lft|Rgt|Dn | | 0| .| |
+ * `---------------------------------------------------------' `---------------'
+ *
+ * M0110 M0120
+ * ,---------------------------------------------------------. ,---------------.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Clr| -| +| *|
+ * |---------------------------------------------------------| |---------------|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| | 7| 8| 9| /|
+ * |---------------------------------------------------------| |---------------|
+ * |Caps | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| ,|
+ * |---------------------------------------------------------| |---------------|
+ * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | | 1| 2| 3| |
+ * `---------------------------------------------------------' |-----------|Ent|
+ * |Opt|Mac | Space |Ent |Opt| | 0| .| |
+ * `-----------------------------------------------' `---------------'
+ * With Shift keys on M0120 work as curosor.(-:Left *:Right /:Up ,:Down)
+ *
+ * NOTE: \ is located differently.
+ * NOTE: Enter on M0110 is different from Enter on keypad(M0120 and M0110A).
+ * NOTE: Left Shift and right Shift are logically same key.
+ * NOTE: Left Option and right Option are logically same key.
+ */
+
+/* Keymap definition Macro
+ * ,---------------------------------------------------------. ,---------------.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Clr| =| /| *|
+ * |---------------------------------------------------------| |---------------|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -|
+ * |-----------------------------------------------------' | |---------------|
+ * |Caps | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| +|
+ * |---------------------------------------------------------| |---------------|
+ * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| |
+ * |---------------------------------------------------------| |-----------|Ent|
+ * |Opt |Mac | Space |Ent| \|Lft|Rgt|Dn | | 0| .| |
+ * `---------------------------------------------------------' `---------------'
+ * NOTE: Ent between Space and \ means Enter on M0110.
+ */
+#define KEYMAP( \
+ K32,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33, K47,K68,K6D,K62, \
+ K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E, K59,K5B,K5C,K4E, \
+ K39,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27, K24, K56,K57,K58,K66, \
+ K38,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C, K4D, K53,K54,K55,K4C, \
+ K3A,K37, K31, K34,K2A,K46,K42,K48, K52, K41 \
+) { \
+ { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07 }, \
+ { KC_##K08, KC_##K09, KC_NO, KC_##K0B, KC_##K0C, KC_##K0D, KC_##K0E, KC_##K0F }, \
+ { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
+ { KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D, KC_##K1E, KC_##K1F }, \
+ { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27 }, \
+ { KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D, KC_##K2E, KC_##K2F }, \
+ { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_NO, KC_NO, KC_##K37 }, \
+ { KC_##K38, KC_##K39, KC_##K3A, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \
+ { KC_NO, KC_##K41, KC_##K42, KC_NO, KC_NO, KC_NO, KC_##K46, KC_##K47 }, \
+ { KC_##K48, KC_NO, KC_NO, KC_NO, KC_##K4C, KC_##K4D, KC_##K4E, KC_NO }, \
+ { KC_NO, KC_NO, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57 }, \
+ { KC_##K58, KC_##K59, KC_NO, KC_##K5B, KC_##K5C, KC_NO, KC_NO, KC_NO }, \
+ { KC_NO, KC_NO, KC_##K62, KC_NO, KC_NO, KC_NO, KC_##K66, KC_NO }, \
+ { KC_##K68, KC_NO, KC_NO, KC_NO, KC_NO, KC_##K6D, KC_NO, KC_NO }, \
+}
--- /dev/null
+/*
+Copyright 2014 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+#include <stdint.h>
+#include "keycode.h"
+#include "keymap_common.h"
+
+
+#ifdef KEYMAP_SECTION_ENABLE
+const uint8_t keymaps[][MATRIX_ROWS][MATRIX_COLS] __attribute__ ((section (".keymap.keymaps"))) = {
+#else
+const uint8_t keymaps[][MATRIX_ROWS][MATRIX_COLS] PROGMEM = {
+#endif
+ /* Default:
+ * ,---------------------------------------------------------. ,---------------.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Clr| =| /| *|
+ * |---------------------------------------------------------| |---------------|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -|
+ * |-----------------------------------------------------' | |---------------|
+ * |Caps | A| S| D| F| G| H| J| K| L| ;| '|Enter | | 4| 5| 6| +|
+ * |---------------------------------------------------------| |---------------|
+ * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| |
+ * |---------------------------------------------------------| |-----------|Ent|
+ * |Ctl |Gui | Space |Alt| \|Lft|Rgt|Dn | | 0| .| |
+ * `---------------------------------------------------------' `---------------'
+ */
+ [0] = KEYMAP(
+ GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, CLR, EQL, PSLS,PAST,
+ TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, P7, P8, P9, PMNS,
+ LCAP,A, S, D, F, G, H, J, K, L, SCLN,QUOT, FN15, P4, P5, P6, PPLS,
+ LSFT,Z, X, C, V, B, N, M, COMM,DOT, SLSH, UP, P1, P2, P3, PENT,
+ LCTL,LGUI, FN16, LALT,FN31,LEFT,RGHT,DOWN, P0, PDOT
+ ),
+ /* Cursor Layer(WASD, IJKL)
+ * ,---------------------------------------------------------. ,---------------.
+ * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delet| |Nlk| =| /| *|
+ * |---------------------------------------------------------| |---------------|
+ * |Caps |Hom| Up|PgU| | | | |Psc|Slk|Pau|Up |Ins| | | 7| 8| 9| -|
+ * |-----------------------------------------------------' | |---------------|
+ * |Caps |Lef|Dow|Rig| | | | |Hom|PgU|Lef|Rig|Enter | | 4| 5| 6| +|
+ * |---------------------------------------------------------| |---------------|
+ * |Shift |End| |PgD| | | | |End|PgD|Dow|Shif|PgU| | 1| 2| 3| |
+ * |---------------------------------------------------------| |-----------|Ent|
+ * |Ctl |Gui | Space |Alt | \|Hom|End|PgD| | 0| .| |
+ * `---------------------------------------------------------' `---------------'
+ */
+ [3] = KEYMAP(
+ ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST,
+ CAPS,HOME,UP, PGUP,NO, NO, NO, NO, PSCR,SLCK,PAUS,UP, INS, P7, P8, P9, PMNS,
+ LCAP,LEFT,DOWN,RGHT,NO, NO, NO, NO, HOME,PGUP,LEFT,RGHT, FN15, P4, P5, P6, PPLS,
+ LSFT,END, NO, PGDN,NO, NO, NO, NO, END, PGDN,DOWN, PGUP, P1, P2, P3, PENT,
+ LCTL,LGUI, FN16, LALT,FN31,HOME,END, PGDN, P0, PDOT
+ ),
+ [4] = KEYMAP(
+ ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST,
+ CAPS,HOME,UP, PGUP,NO, NO, NO, NO, PSCR,SLCK,PAUS,UP, INS, P7, P8, P9, PMNS,
+ LCAP,LEFT,DOWN,RGHT,NO, NO, NO, NO, HOME,PGUP,LEFT,RGHT, FN15, P4, P5, P6, PPLS,
+ LSFT,END, NO, PGDN,NO, NO, NO, NO, END, PGDN,DOWN, PGUP, P1, P2, P3, PENT,
+ LCTL,LGUI, FN16, LALT,FN31,HOME,END, PGDN, P0, PDOT
+ ),
+ [7] = {},
+};
+
+
+/*
+ * Fn action definition
+ */
+#ifdef KEYMAP_SECTION_ENABLE
+const uint16_t fn_actions[] __attribute__ ((section (".keymap.fn_actions"))) = {
+#else
+const uint16_t fn_actions[] PROGMEM = {
+#endif
+ [0] = ACTION_LAYER_MOMENTARY(1),
+ [1] = ACTION_LAYER_MOMENTARY(2),
+ [2] = ACTION_LAYER_MOMENTARY(3),
+ [3] = ACTION_LAYER_MOMENTARY(4),
+ [4] = ACTION_LAYER_MOMENTARY(5),
+ [5] = ACTION_LAYER_MOMENTARY(6),
+ [6] = ACTION_LAYER_MOMENTARY(7),
+ [7] = ACTION_LAYER_TOGGLE(1),
+ [8] = ACTION_LAYER_TOGGLE(2),
+ [9] = ACTION_LAYER_TOGGLE(3),
+ [10] = ACTION_LAYER_TAP_TOGGLE(1),
+ [11] = ACTION_LAYER_TAP_TOGGLE(2),
+ [12] = ACTION_LAYER_TAP_TOGGLE(3),
+ [13] = ACTION_LAYER_TAP_KEY(1, KC_F),
+ [14] = ACTION_LAYER_TAP_KEY(2, KC_J),
+ [15] = ACTION_LAYER_TAP_KEY(3, KC_ENTER),
+ [16] = ACTION_LAYER_TAP_KEY(4, KC_SPACE),
+ [17] = ACTION_LAYER_TAP_KEY(5, KC_SCOLON),
+ [18] = ACTION_LAYER_TAP_KEY(6, KC_QUOTE),
+ [19] = ACTION_LAYER_TAP_KEY(7, KC_SLASH),
+ [20] = ACTION_MODS_TAP_KEY(MOD_LSFT, KC_SPACE),
+ [21] = ACTION_MODS_TAP_KEY(MOD_LCTL, KC_SPACE),
+ [22] = ACTION_MODS_TAP_KEY(MOD_RCTL, KC_QUOTE),
+ [23] = ACTION_MODS_TAP_KEY(MOD_RCTL, KC_ENTER),
+ [24] = ACTION_MODS_TAP_KEY(MOD_LCTL, KC_ESC),
+ [25] = ACTION_MODS_TAP_KEY(MOD_LCTL, KC_BSPACE),
+ [26] = ACTION_MODS_ONESHOT(MOD_LCTL),
+ [27] = ACTION_MODS_TAP_KEY(MOD_LSFT, KC_ESC),
+ [28] = ACTION_MODS_TAP_KEY(MOD_LSFT, KC_BSPACE),
+ [29] = ACTION_MODS_ONESHOT(MOD_LSFT),
+ [30] = ACTION_MODS_TAP_KEY(MOD_RSFT, KC_GRAVE),
+ [31] = ACTION_MODS_TAP_KEY(MOD_RALT, KC_BSLASH),
+};
/*
-Copyright 2011,2012 Jun Wako <wakojun@gmail.com>
+Copyright 2014 Jun Wako <wakojun@gmail.com>
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
-/* M0110A Support was contributed by skagon@github */
-
#include <stdint.h>
-#include <stdbool.h>
-#include <avr/pgmspace.h>
#include "keycode.h"
-#include "print.h"
-#include "debug.h"
-#include "util.h"
-#include "keymap.h"
-
-
-/*
- * The keymap works with both M0110 and M0110A keyboards. As you can see, the M0110A is a superset
- * of the M0110 keyboard, with only one exception: 'Enter' in M0110 does not exist
- * on the M0110A, but since it generates a unique scan code which is not used for some other key in
- * the M0110A, they are totally interchangeable. In fact, the M0110A is functionally (almost)
- * identical to the combination of the M0110 along with the M0120 keypad. The only difference
- * (which is causing some problems as you will read below) is that the M0110+M0120 don't have
- * dedicated arrow keys, while the M0110A does. However, the M0120 did have arrow keys, which
- * doubled as the [comma], [/], [*] and [+] keys, when used with the [Shift] key. The M0110A has
- * substituted the [comma] key with the [=] key, however its scancode is the same.
- *
- * Physical layout:
- * M0110A
- * ,---------------------------------------------------------. ,---------------.
- * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Bcksp| |Clr| =| /| *|
- * |---------------------------------------------------------| |---------------|
- * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -|
- * |-----------------------------------------------------' | |---------------|
- * |Caps | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| +|
- * |---------------------------------------------------------| |---------------|
- * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| |
- * |---------------------------------------------------------' |-----------|Ent|
- * |Opt |Mac | Space | \|Lft|Rgt|Dn | | 0| .| |
- * `---------------------------------------------------------' `---------------'
- *
- * M0110 M0120
- * ,---------------------------------------------------------. ,---------------.
- * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Clr| -| +| *|
- * |---------------------------------------------------------| |---------------|
- * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| | 7| 8| 9| /|
- * |---------------------------------------------------------| |---------------|
- * |Caps | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| ,|
- * |---------------------------------------------------------| |---------------|
- * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | | 1| 2| 3| |
- * `---------------------------------------------------------' |-----------|Ent|
- * |Opt|Mac | Space |Ent |Opt| | 0| .| |
- * `-----------------------------------------------' `---------------'
- * With Shift keys on M0120 work as curosor.(-:Left *:Right /:Up ,:Down)
- *
- * NOTE: \ is located differently.
- * NOTE: Enter on M0110 is different from Enter on keypad(M0120 and M0110A).
- * NOTE: Left Shift and right Shift are logically same key.
- * NOTE: Left Option and right Option are logically same key.
- */
-
-/* Keymap definition Macro
- * ,---------------------------------------------------------. ,---------------.
- * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Clr| =| /| *|
- * |---------------------------------------------------------| |---------------|
- * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -|
- * |-----------------------------------------------------' | |---------------|
- * |Caps | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| +|
- * |---------------------------------------------------------| |---------------|
- * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| |
- * |---------------------------------------------------------| |-----------|Ent|
- * |Opt |Mac | Space |Ent| \|Lft|Rgt|Dn | | 0| .| |
- * `---------------------------------------------------------' `---------------'
- * NOTE: Ent between Space and \ means Enter on M0110.
- */
-#define KEYMAP( \
- K32,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33, K47,K68,K6D,K62, \
- K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E, K59,K5B,K5C,K4E, \
- K39,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27, K24, K56,K57,K58,K66, \
- K38,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C, K4D, K53,K54,K55,K4C, \
- K3A,K37, K31, K34,K2A,K46,K42,K48, K52, K41 \
-) { \
- { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07 }, \
- { KC_##K08, KC_##K09, KC_NO, KC_##K0B, KC_##K0C, KC_##K0D, KC_##K0E, KC_##K0F }, \
- { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
- { KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D, KC_##K1E, KC_##K1F }, \
- { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27 }, \
- { KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D, KC_##K2E, KC_##K2F }, \
- { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_NO, KC_NO, KC_##K37 }, \
- { KC_##K38, KC_##K39, KC_##K3A, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \
- { KC_NO, KC_##K41, KC_##K42, KC_NO, KC_NO, KC_NO, KC_##K46, KC_##K47 }, \
- { KC_##K48, KC_NO, KC_NO, KC_NO, KC_##K4C, KC_##K4D, KC_##K4E, KC_NO }, \
- { KC_NO, KC_NO, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57 }, \
- { KC_##K58, KC_##K59, KC_NO, KC_##K5B, KC_##K5C, KC_NO, KC_NO, KC_NO }, \
- { KC_NO, KC_NO, KC_##K62, KC_NO, KC_NO, KC_NO, KC_##K66, KC_NO }, \
- { KC_##K68, KC_NO, KC_NO, KC_NO, KC_NO, KC_##K6D, KC_NO, KC_NO }, \
-}
-
-#define KEYCODE(layer, row, col) (pgm_read_byte(&keymaps[(layer)][(row)][(col)]))
-
-
-// Assign Fn key(0-7) to a layer to which switch with the Fn key pressed.
-static const uint8_t PROGMEM fn_layer[] = {
- 1, // Fn0
- 2, // Fn1
- 3, // Fn2
- 1, // Fn3
- 2, // Fn4
- 0, // Fn5
- 0, // Fn6
- 0 // Fn7
-};
+#include "keymap_common.h"
-// Assign Fn key(0-7) to a keycode sent when release Fn key without use of the layer.
-// See layer.c for details.
-static const uint8_t PROGMEM fn_keycode[] = {
- KC_ENTER, // Fn0
- KC_SCOLON, // Fn1
- KC_SLASH, // Fn2
- KC_UP, // Fn3
- KC_NO, // Fn4
- KC_NO, // Fn5
- KC_NO, // Fn6
- KC_NO // Fn7
-};
-static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
/* Default:
- * M0110 M0120
- * ,---------------------------------------------------------. ,---------------.
- * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Gui| -| +| *|
- * |---------------------------------------------------------| |---------------|
- * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| | 7| 8| 9| /|
- * |---------------------------------------------------------| |---------------|
- * |Ctrl | A| S| D| F| G| H| J| K| L| Fn| '|Return| | 4| 5| 6| ,|
- * |---------------------------------------------------------| |---------------|
- * |Shift | Z| X| C| V| B| N| M| ,| ,| Fn|Shift | | 1| 2| 3| |
- * `---------------------------------------------------------' |-----------|Ent|
- * |Fn |alt | Space |Gui |Fn | | 0| .| |
- * `-----------------------------------------------' `---------------'
+ * M0110
+ * ,---------------------------------------------------------.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs|
+ * |---------------------------------------------------------|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \|
+ * |---------------------------------------------------------|
+ * |Ctrl | A| S| D| F| G| H| J| K| L| Fn| '|Return|
+ * |---------------------------------------------------------|
+ * |Shift | Z| X| C| V| B| N| M| ,| ,| Fn|Shift |
+ * `---------------------------------------------------------'
+ * |Fn |alt | Fn |Gui |Fn |
+ * `-----------------------------------------------'
*/
- KEYMAP(
+ [0] = KEYMAP(
ESC, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, NLCK,EQL, PSLS,PAST,
TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, P7, P8, P9, PMNS,
- LCTL,A, S, D, F, G, H, J, K, L, FN1, QUOT, FN0, P4, P5, P6, PPLS,
- LSFT,Z, X, C, V, B, N, M, COMM,DOT, FN2, FN3, P1, P2, P3, PENT,
- FN4, LALT, SPC, LGUI,BSLS,LGUI,RCTL,RCTL, LGUI, PDOT
+ LCTL,A, S, D, F, G, H, J, K, L, FN3, QUOT, ENT, P4, P5, P6, PPLS,
+ LSFT,Z, X, C, V, B, N, M, COMM,DOT, FN1, UP, P1, P2, P3, PENT,
+ FN0, LALT, FN2, LGUI,BSLS,LEFT,RGHT,DOWN, P0, PDOT
),
- // HHKB & WASD
- KEYMAP(
+ // IJKL cursor
+ [1] = KEYMAP(
GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST,
- CAPS,NO, NO, NO, NO, NO, NO, NO, PSCR,SLCK,PAUS,UP, NO, P7, P8, P9, PMNS,
- LCTL,VOLD,VOLU,MUTE,NO, NO, NO, NO, HOME,PGUP,LEFT,RGHT, FN0, P4, P5, P6, PPLS,
- LSFT,NO, NO, NO, NO, NO, NO, NO, END, PGDN,DOWN, FN3, P1, P2, P3, PENT,
- LCTL,LALT, SPC, LGUI,INS, LGUI,RCTL,RCTL, P0, PDOT
+ CAPS,NO, NO, NO, NO, NO, HOME,PGDN,UP, PGUP,END, NO, NO, P7, P8, P9, PMNS,
+ LCTL,VOLD,VOLU,MUTE,NO, NO, HOME,LEFT,DOWN,RGHT,END, NO, ENT, P4, P5, P6, PPLS,
+ LSFT,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, NO, PGUP, P1, P2, P3, PENT,
+ TRNS,LALT, SPC, LGUI,BSLS,HOME,END, PGDN, P0, PDOT
),
- // vi mousekeys
- KEYMAP(
+ // HJKL cursor
+ [2] = KEYMAP(
GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST,
- CAPS,NO, NO, NO, NO, NO, WH_L,WH_D,WH_U,WH_R,PSCR,SLCK,PAUS, P7, P8, P9, PMNS,
- LCTL,VOLD,VOLU,MUTE,NO, NO, MS_L,MS_D,MS_U,MS_R,FN1, NO, ENT, P4, P5, P6, PPLS,
- LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,NO, NO, NO, NO, P1, P2, P3, PENT,
- FN4, LALT, BTN1, LGUI,NO, LGUI,RCTL,RCTL, P0, PDOT
+ CAPS,NO, NO, NO, NO, NO, HOME,PGDN,UP, PGUP,END, NO, NO, P7, P8, P9, PMNS,
+ LCTL,VOLD,VOLU,MUTE,NO, NO, LEFT,DOWN,UP, RGHT,NO, NO, ENT, P4, P5, P6, PPLS,
+ LSFT,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, TRNS, PGUP, P1, P2, P3, PENT,
+ TRNS,LALT, SPC, LGUI,BSLS,HOME,END, PGDN, P0, PDOT
),
- // vi cusorkeys
- KEYMAP(
+ // Mousekey
+ [3] = KEYMAP(
GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST,
- CAPS,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, PSCR,SLCK,PAUS, P7, P8, P9, PMNS,
- LCTL,NO, NO, NO, NO, NO, LEFT,DOWN,UP, RGHT,NO, NO, ENT, P4, P5, P6, PPLS,
- LSFT,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, FN2, NO, P1, P2, P3, PENT,
- LCTL,LALT, SPC, LGUI,INS, LGUI,RCTL,RCTL, P0, PDOT
+ CAPS,Q, W, E, R, T, WH_L,WH_D,MS_U,WH_U,WH_R,WBAK,WFWD, P7, P8, P9, PMNS,
+ LCTL,VOLD,VOLU,MUTE,NO, NO, BTN2,MS_L,MS_D,MS_R,BTN1,NO, ENT, P4, P5, P6, PPLS,
+ LSFT,Z, X, C, V, B, BTN2,BTN1,BTN4,BTN5,NO, PGUP, P1, P2, P3, PENT,
+ NO, LALT, TRNS, LGUI,BSLS,HOME,END, PGDN, P0, PDOT
+ ),
+ // Mousekey
+ [4] = KEYMAP(
+ GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST,
+ CAPS,Q, W, E, R, T, WH_L,WH_D,MS_U,WH_U,WH_R,WBAK,WFWD, P7, P8, P9, PMNS,
+ LCTL,VOLD,VOLU,MUTE,NO, NO, BTN2,MS_L,MS_D,MS_R,TRNS,NO, ENT, P4, P5, P6, PPLS,
+ LSFT,Z, X, C, V, B, BTN2,BTN1,BTN4,BTN5,NO, PGUP, P1, P2, P3, PENT,
+ NO, LALT, BTN1, LGUI,BSLS,HOME,END, PGDN, P0, PDOT
),
};
-uint8_t keymap_get_keycode(uint8_t layer, uint8_t row, uint8_t col)
-{
- return KEYCODE(layer, row, col);
-}
-
-uint8_t keymap_fn_layer(uint8_t index)
-{
- return pgm_read_byte(&fn_layer[index]);
-}
-
-uint8_t keymap_fn_keycode(uint8_t index)
-{
- return pgm_read_byte(&fn_keycode[index]);
-}
+/*
+ * Fn action definition
+ */
+const uint16_t fn_actions[] PROGMEM = {
+ [0] = ACTION_LAYER_MOMENTARY(1),
+ [1] = ACTION_LAYER_TAP_KEY(2, KC_SLASH),
+ [2] = ACTION_LAYER_TAP_KEY(3, KC_SPACE),
+ [3] = ACTION_LAYER_TAP_KEY(4, KC_SCOLON),
+};
--- /dev/null
+/*
+Copyright 2014 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+#include <stdint.h>
+#include "keycode.h"
+#include "keymap_common.h"
+
+
+const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ /* Default:
+ * M0110 M0120
+ * ,---------------------------------------------------------. ,---------------.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Nlk| -| +| *|
+ * |---------------------------------------------------------| |---------------|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| | 7| 8| 9| /|
+ * |---------------------------------------------------------| |---------------|
+ * |Ctrl | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| ,|
+ * |---------------------------------------------------------| |---------------|
+ * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | | 1| 2| 3| |
+ * `---------------------------------------------------------' |-----------|Ent|
+ * |Opt|Mac | Space |Mac |Opt| | 0| .| |
+ * `-----------------------------------------------' `---------------'
+ * M0110A
+ * ,---------------------------------------------------------. ,---------------.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Bcksp| |Nlk| =| /| *|
+ * |---------------------------------------------------------| |---------------|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -|
+ * |-----------------------------------------------------' | |---------------|
+ * |Caps | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| +|
+ * |---------------------------------------------------------| |---------------|
+ * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| |
+ * |---------------------------------------------------------' |-----------|Ent|
+ * |Opt |Mac | Space | \|Lft|Rgt|Dn | | 0| .| |
+ * `---------------------------------------------------------' `---------------'
+ */
+ [0] = KEYMAP(
+ GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, NLCK,PEQL,PSLS,PAST,
+ TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, P7, P8, P9, PMNS,
+ LCAP,A, S, D, F, G, H, J, K, L, SCLN,QUOT, ENT, P4, P5, P6, PPLS,
+ LSFT,Z, X, C, V, B, N, M, COMM,DOT, SLSH, UP, P1, P2, P3, PENT,
+ LALT,LGUI, SPC, RGUI,BSLS,LEFT,RGHT,DOWN, P0, PDOT
+ ),
+};
+
+/*
+ * Fn action definition
+ */
+const uint16_t fn_actions[] PROGMEM = {
+};
+
+
--- /dev/null
+/*
+Copyright 2014 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+#include <stdint.h>
+#include "keycode.h"
+#include "keymap_common.h"
+
+
+const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ /* Default:
+ * M0110 M0120
+ * ,---------------------------------------------------------. ,---------------.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Nlk| -| +| *|
+ * |---------------------------------------------------------| |---------------|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| | 7| 8| 9| /|
+ * |---------------------------------------------------------| |---------------|
+ * |Ctrl | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| ,|
+ * |---------------------------------------------------------| |---------------|
+ * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | | 1| 2| 3| |
+ * `---------------------------------------------------------' |-----------|Ent|
+ * |Opt|Mac | Space |Mac |Opt| | 0| .| |
+ * `-----------------------------------------------' `---------------'
+ * M0110A
+ * ,---------------------------------------------------------. ,---------------.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Bcksp| |Nlk| =| /| *|
+ * |---------------------------------------------------------| |---------------|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -|
+ * |-----------------------------------------------------' | |---------------|
+ * |Caps | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| +|
+ * |---------------------------------------------------------| |---------------|
+ * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| |
+ * |---------------------------------------------------------' |-----------|Ent|
+ * |Opt |Mac | Space | \|Lft|Rgt|Dn | | 0| .| |
+ * `---------------------------------------------------------' `---------------'
+ */
+ [0] = KEYMAP(
+ GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, NLCK,PEQL,PSLS,PAST,
+ TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, P7, P8, P9, PMNS,
+ LCTL,A, S, D, F, G, H, J, K, L, SCLN,QUOT, ENT, P4, P5, P6, PPLS,
+ LSFT,Z, X, C, V, B, N, M, COMM,DOT, SLSH, UP, P1, P2, P3, PENT,
+ LALT,LGUI, FN0, RGUI,BSLS,LEFT,RGHT,DOWN, P0, PDOT
+ ),
+ [1] = KEYMAP(
+ ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST,
+ TRNS,TRNS,TRNS,ESC, TRNS,TRNS,TRNS,HOME,UP, END, PSCR,SLCK,PAUS, P7, P8, P9, PMNS,
+ LCTL,TRNS,TRNS,TRNS,TRNS,TRNS,PGUP,LEFT,DOWN,RGHT,TRNS,TRNS, TRNS, P4, P5, P6, PPLS,
+ TRNS,TRNS,TRNS,TRNS,TRNS,SPC, PGDN,GRV, FN1, TRNS,APP, PGUP, P1, P2, P3, PENT,
+ TRNS,TRNS, TRNS, TRNS,INS, HOME,END, PGDN, P0, PDOT
+ ),
+};
+
+/*
+ * Fn action definition
+ */
+const uint16_t fn_actions[] PROGMEM = {
+ [0] = ACTION_LAYER_TAP_KEY(1, KC_SPACE),
+ [1] = ACTION_MODS_KEY(MOD_LSFT, KC_GRV), // tilde
+};
Pin mini DIN MCU
----------------------------------
- 1 ~RST PD1
+ 1 ~RST(TXD) PD3
2 GND GND
3 ~RDY PD4
4 RXD PD2
Signal: Asynchronous, Positive logic, 19200baud, Least bit first
Frame format: 1-Start bit(Lo), 8-Data bits, Odd-Parity, 1-Stop bit
-This converter uses software method for testing purpose. AVR UART engine will work better.
-
-
Build Firmware
+#
+# Makefile for Teensy
+#
# Target file name (without extension).
TARGET = ps2_usb_lufa
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+OPT_DEFS += -DBOOTLOADER_SIZE=512
# Build Options
+++ /dev/null
-# Target file name (without extension).
-TARGET = ps2_usb_jis
-
-# Directory common source filess exist
-TOP_DIR = ../..
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162 # Teensy 1.0
-MCU = atmega32u4 # Teensy 2.0
-#MCU = at90usb646 # Teensy++ 1.0
-#MCU = at90usb1286 # Teensy++ 2.0
-
-
-# Processor frequency.
-# Normally the first thing your program should do is set the clock prescaler,
-# so your program will run at the correct speed. You should also set this
-# variable to same clock speed. The _delay_ms() macro uses this, and many
-# examples use this variable to calculate timings. Do not add a "UL" here.
-F_CPU = 16000000
-
-
-# Build Options
-# *Comment out* to disable the options.
-#
-MOUSEKEY_ENABLE = yes # Mouse keys
-EXTRAKEY_ENABLE = yes # Audio control and System control
-NKRO_ENABLE = yes # USB Nkey Rollover
-
-#PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
-#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
-PS2_USE_BUSYWAIT = yes # uses primitive reference code
-
-
-# keyboard dependent files
-SRC = keymap_jis.c \
- matrix.c \
- led.c
-
-
-ifdef PS2_USE_USART
- SRC += protocol/ps2_usart.c
- OPT_DEFS += -DPS2_USE_USART
-endif
-ifdef PS2_USE_INT
- SRC += protocol/ps2.c
- OPT_DEFS += -DPS2_USE_INT
-endif
-ifdef PS2_USE_BUSYWAIT
- SRC += protocol/ps2.c
- OPT_DEFS += -DPS2_USE_BUSYWAIT
-endif
-
-
-#CONFIG_H = config_pjrc_usart.h
-CONFIG_H = config.h
-
-
-#---------------- Programming Options --------------------------
-PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
-
-
-include $(TOP_DIR)/protocol/pjrc.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
--- /dev/null
+#
+# Makefile for TMK keyboard converter rev2
+# https://github.com/tmk/keyboard_converter#pcb-rev1
+#
+# Target file name (without extension).
+TARGET = ps2_usb_tmk_rev1
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# project specific files
+SRC = keymap_common.c \
+ matrix.c \
+ led.c
+
+ifdef KEYMAP
+ SRC := keymap_$(KEYMAP).c $(SRC)
+else
+ SRC := keymap_plain.c $(SRC)
+endif
+
+CONFIG_H = config_tmk_rev1.h
+
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+# comment out to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = yes # Console for debug(+400)
+COMMAND_ENABLE = yes # Commands for debug and configuration
+#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
+
+
+# PS/2 Options
+#
+PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
+#PS2_USE_BUSYWAIT = yes # uses primitive reference code
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+include $(TOP_DIR)/protocol.mk
+include $(TOP_DIR)/protocol/lufa.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk
--- /dev/null
+#
+# Makefile for TMK keyboard converter rev2
+# https://github.com/tmk/keyboard_converter#pcb-rev2
+#
+# Target file name (without extension).
+TARGET = ps2_usb_tmk_rev2
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# project specific files
+SRC = keymap_common.c \
+ matrix.c \
+ led.c
+
+ifdef KEYMAP
+ SRC := keymap_$(KEYMAP).c $(SRC)
+else
+ SRC := keymap_plain.c $(SRC)
+endif
+
+CONFIG_H = config_tmk_rev2.h
+
+
+# MCU name
+MCU = atmega32u2
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+# comment out to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = yes # Console for debug(+400)
+COMMAND_ENABLE = yes # Commands for debug and configuration
+#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
+
+
+# PS/2 Options
+#
+PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
+#PS2_USE_BUSYWAIT = yes # uses primitive reference code
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+include $(TOP_DIR)/protocol.mk
+include $(TOP_DIR)/protocol/lufa.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk
PS/2 to USB keyboard converter
==============================
-This firmware converts PS/2 keyboard protocol to USB and supports only Scan Code Set 2.
-
-
-PS/2 signal handling implementations
-------------------------------------
-Following three methods are used to implement PS/2 signal handling.
-
-### Simple and stupid busy-wait(ps2_busywait.c)
- This is expected to implemented with portable C code for reference.
-### Interrupt driven(ps2_interrupt.c)
- Uses pin interrupt to detect falling edge of clock line.
-### USART hardware module(ps2_usart.c)
- Uses AVR USART engine to receive PS/2 signal.
-
-To select method edit Makefile.
+This firmware converts PS/2 keyboard protocol to USB.(It supports Scan Code Set 2.)
Connect Wires
-------------
In case of Teensy2.0(ATMega32U4):
-1. Connect Vcc and GND.
-2. Connect Clock and Data line.
- - Busywait: Clock is on PD5 and Data on PD2.
- - Interrupt: Clock is on PD1 and Data on PD2.
- - USART: Clock is on PD5 and Data on PD2.
-3. Optionally you need pull-up register. 1K-10K Ohm is OK.
+1. Connect **Vcc** and **GND**.
+2. Connect **Clock** and **Data** line.
+ - **Interrupt**: **Clock** is on `PD1` and **Data** on `PD0`.(Recommended. Soarer's converter compatible)
+ - **Busywait**: **Clock** is on `PD1` and **Data** on `PD0`.
+ - **USART**: **Clock** is on `PD5` and **Data** on `PD2`.
+3. Optionally you need pull-up resistor. 1K-10K Ohm is OK.
To change pin configuration edit config.h.
Build Firmware
--------------
-Just run `make`:
+For **PJRC Teensy** just run `make`:
+ $ make clean
$ make
To select keymap:
+ $ make clean
$ make KEYMAP=[plain|jis|spacefn|...]
+After that you will find HEX file `ps2_usb_lufa.hex` in current directory.
+
+
+- For **TMK converter Rev.1** use `make -f Makefile.tmk_rev1` instead of `make` and HEX file is `ps2_usb_tmk_rev1.hex`.
+
+- For **TMK converter Rev.2** use `make -f Makefile.tmk_rev2` instead of `make` and HEX file is `ps2_usb_tmk_rev2.hex`.
+
Keymap
------
-Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `keymap_<name>.c` and see keymap document(you can find in top README.md) and existent keymap files.
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `keymap_<name>.c` and see keymap document(you can find in README.md of top directory) and existent keymap files.
+
+
+PS/2 signal handling implementations
+------------------------------------
+Following three methods can be used to implement PS/2 signal handling.
+
+### Simple and stupid busy-wait(ps2_busywait.c)
+ This is expected to implemented with portable C code for reference.
+### Interrupt driven(ps2_interrupt.c)
+ Uses pin interrupt to detect falling edge of clock line.
+### USART hardware module(ps2_usart.c)
+ Uses AVR USART engine to receive PS/2 signal.
+
+To select method edit Makefile.
V-USB Support
--- /dev/null
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include <avr/interrupt.h>
+
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x6512
+#define DEVICE_VER 0x0001
+#define MANUFACTURER t.m.k.
+#define PRODUCT PS/2 keyboard converter
+#define DESCRIPTION convert PS/2 keyboard to USB
+
+
+/* matrix size */
+#define MATRIX_ROWS 32 // keycode bit: 3-0
+#define MATRIX_COLS 8 // keycode bit: 6-4
+
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) || \
+ keyboard_report->mods == (MOD_BIT(KC_LCTRL) | MOD_BIT(KC_RSHIFT)) \
+)
+
+
+//#define NO_SUSPEND_POWER_DOWN
+
+
+/*
+ * PS/2 Busywait
+ */
+#ifdef PS2_USE_BUSYWAIT
+#define PS2_CLOCK_PORT PORTD
+#define PS2_CLOCK_PIN PIND
+#define PS2_CLOCK_DDR DDRD
+#define PS2_CLOCK_BIT 5
+#define PS2_DATA_PORT PORTD
+#define PS2_DATA_PIN PIND
+#define PS2_DATA_DDR DDRD
+#define PS2_DATA_BIT 2
+#endif
+
+/*
+ * PS/2 USART
+ */
+#ifdef PS2_USE_USART
+#if defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__)
+/* XCK for clock line and RXD for data line */
+#define PS2_CLOCK_PORT PORTD
+#define PS2_CLOCK_PIN PIND
+#define PS2_CLOCK_DDR DDRD
+#define PS2_CLOCK_BIT 5
+#define PS2_DATA_PORT PORTD
+#define PS2_DATA_PIN PIND
+#define PS2_DATA_DDR DDRD
+#define PS2_DATA_BIT 2
+/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
+/* set DDR of CLOCK as input to be slave */
+#define PS2_USART_INIT() do { \
+ PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT); \
+ PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT); \
+ UCSR1C = ((1 << UMSEL10) | \
+ (3 << UPM10) | \
+ (0 << USBS1) | \
+ (3 << UCSZ10) | \
+ (0 << UCPOL1)); \
+ UCSR1A = 0; \
+ UBRR1H = 0; \
+ UBRR1L = 0; \
+} while (0)
+#define PS2_USART_RX_INT_ON() do { \
+ UCSR1B = ((1 << RXCIE1) | \
+ (1 << RXEN1)); \
+} while (0)
+#define PS2_USART_RX_POLL_ON() do { \
+ UCSR1B = (1 << RXEN1); \
+} while (0)
+#define PS2_USART_OFF() do { \
+ UCSR1C = 0; \
+ UCSR1B &= ~((1 << RXEN1) | \
+ (1 << TXEN1)); \
+} while (0)
+#define PS2_USART_RX_READY (UCSR1A & (1<<RXC1))
+#define PS2_USART_RX_DATA UDR1
+#define PS2_USART_ERROR (UCSR1A & ((1<<FE1) | (1<<DOR1) | (1<<UPE1)))
+#define PS2_USART_RX_VECT USART1_RX_vect
+#elif defined(__AVR_ATmega168__) || defined(__AVR_ATmega168P__) || defined(__AVR_ATmega328P__)
+/* XCK for clock line and RXD for data line */
+#define PS2_CLOCK_PORT PORTD
+#define PS2_CLOCK_PIN PIND
+#define PS2_CLOCK_DDR DDRD
+#define PS2_CLOCK_BIT 4
+#define PS2_DATA_PORT PORTD
+#define PS2_DATA_PIN PIND
+#define PS2_DATA_DDR DDRD
+#define PS2_DATA_BIT 0
+/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
+/* set DDR of CLOCK as input to be slave */
+#define PS2_USART_INIT() do { \
+ PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT); \
+ PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT); \
+ UCSR0C = ((1 << UMSEL00) | \
+ (3 << UPM00) | \
+ (0 << USBS0) | \
+ (3 << UCSZ00) | \
+ (0 << UCPOL0)); \
+ UCSR0A = 0; \
+ UBRR0H = 0; \
+ UBRR0L = 0; \
+} while (0)
+#define PS2_USART_RX_INT_ON() do { \
+ UCSR0B = ((1 << RXCIE0) | \
+ (1 << RXEN0)); \
+} while (0)
+#define PS2_USART_RX_POLL_ON() do { \
+ UCSR0B = (1 << RXEN0); \
+} while (0)
+#define PS2_USART_OFF() do { \
+ UCSR0C = 0; \
+ UCSR0B &= ~((1 << RXEN0) | \
+ (1 << TXEN0)); \
+} while (0)
+#define PS2_USART_RX_READY (UCSR0A & (1<<RXC0))
+#define PS2_USART_RX_DATA UDR0
+#define PS2_USART_ERROR (UCSR0A & ((1<<FE0) | (1<<DOR0) | (1<<UPE0)))
+#define PS2_USART_RX_VECT USART_RX_vect
+#endif
+#endif
+
+#endif
--- /dev/null
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include <avr/interrupt.h>
+
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x6512
+#define DEVICE_VER 0x0001
+#define MANUFACTURER t.m.k.
+#define PRODUCT PS/2 keyboard converter
+#define DESCRIPTION convert PS/2 keyboard to USB
+
+
+/* matrix size */
+#define MATRIX_ROWS 32 // keycode bit: 3-0
+#define MATRIX_COLS 8 // keycode bit: 6-4
+
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+
+//#define NO_SUSPEND_POWER_DOWN
+
+
+/*
+ * PS/2 Busywait
+ */
+#ifdef PS2_USE_BUSYWAIT
+#define PS2_CLOCK_PORT PORTD
+#define PS2_CLOCK_PIN PIND
+#define PS2_CLOCK_DDR DDRD
+#define PS2_CLOCK_BIT 1
+#define PS2_DATA_PORT PORTD
+#define PS2_DATA_PIN PIND
+#define PS2_DATA_DDR DDRD
+#define PS2_DATA_BIT 0
+#endif
+
+/*
+ * PS/2 Pin interrupt
+ */
+#ifdef PS2_USE_INT
+/* uses INT1 for clock line(ATMega32U4) */
+#define PS2_CLOCK_PORT PORTD
+#define PS2_CLOCK_PIN PIND
+#define PS2_CLOCK_DDR DDRD
+#define PS2_CLOCK_BIT 1
+#define PS2_DATA_PORT PORTD
+#define PS2_DATA_PIN PIND
+#define PS2_DATA_DDR DDRD
+#define PS2_DATA_BIT 0
+#define PS2_INT_INIT() do { \
+ EICRA |= ((1<<ISC11) | \
+ (0<<ISC10)); \
+} while (0)
+#define PS2_INT_ON() do { \
+ EIMSK |= (1<<INT1); \
+} while (0)
+#define PS2_INT_OFF() do { \
+ EIMSK &= ~(1<<INT1); \
+} while (0)
+#define PS2_INT_VECT INT1_vect
+#endif
+
+#endif
* ,-----------------------------------------------------------.
* |` | F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delete |
* |-----------------------------------------------------------|
- * | | | | | | | |Hom|Up |End|Psc|Slk|Pau|Ins |
+ * | | | |Esc| | | |Hom|Up |End|Psc|Slk|Pau|Ins |
* |-----------------------------------------------------------|
* | | | | | | |PgU|Lef|Dow|Rig| | | |
* |-----------------------------------------------------------|
- * | | | | | |Spc|PgD|` |~ | | | |
+ * | | | | | |Spc|PgD|` |~ | |Men| |
* |-----------------------------------------------------------|
* | | | | | | | | |
* `-----------------------------------------------------------'
GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, INS, HOME,PGUP, NLCK,PSLS,PAST,PMNS,
TRNS,TRNS,TRNS,ESC, TRNS,TRNS,TRNS,HOME,UP, END, PSCR,SLCK,PAUS,INS, DEL, END, PGDN, P7, P8, P9,
TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,PGUP,LEFT,DOWN,RGHT,TRNS,TRNS, TRNS, P4, P5, P6, PPLS,
- TRNS,TRNS,TRNS,TRNS,TRNS,SPC, PGDN,GRV, FN1, TRNS,TRNS, TRNS, UP, P1, P2, P3,
+ TRNS,TRNS,TRNS,TRNS,TRNS,SPC, PGDN,GRV, FN1, TRNS,APP, TRNS, UP, P1, P2, P3,
TRNS,TRNS,TRNS, TRNS, TRNS,TRNS,TRNS,TRNS, LEFT,DOWN,RGHT, P0, PDOT,PENT
),
};
# MCU name, you MUST set this to match the board you are using
# type "make clean" after changing this, so all files will be rebuilt
#MCU = at90usb162 # Teensy 1.0
-MCU = atmega32u4 # Teensy 2.0
+#MCU = atmega32u4 # Teensy 2.0
#MCU = at90usb646 # Teensy++ 1.0
#MCU = at90usb1286 # Teensy++ 2.0
+MCU = atmega32u2
# Processor frequency.
void matrix_init(void)
{
+ DDRD |= (1<<6);
+ PORTD |= (1<<6);
debug_enable = true;
serial_init();
ifdef KEYMAP
SRC := keymap_$(KEYMAP).c $(SRC)
else
- SRC := keymap_hasu.c $(SRC)
+ SRC := keymap_hhkb.c $(SRC)
endif
CONFIG_H = config.h
F_USB = $(F_CPU)
# Interrupt driven control endpoint task
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
F_USB = $(F_CPU)
# Interrupt driven control endpoint task
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
EXTRAKEY_ENABLE = yes # Audio control and System control
#CONSOLE_ENABLE = yes # Console for debug
COMMAND_ENABLE = yes # Commands for debug and configuration
-#NKRO_ENABLE = yes # USB Nkey Rollover
-#KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
+NKRO_ENABLE = yes # USB Nkey Rollover
+KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
# Search Path
* |-----------------------------------------------------------|
* |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]|Backs|
* |-----------------------------------------------------------|
- * |Contro| A| S| D| F| G| H| J| K| L|Fn3| '|Fn4 |
+ * |Contro| A| S| D| F| G| H| J| K| L|Fn3| '|Fn6 |
* |-----------------------------------------------------------|
- * |Fn5 | Z| X| C| V| B| N| M| ,| .|Fn2|Shift |Fn1|
+ * |Fn7 | Z| X| C| V| B| N| M| ,| .|Fn2|Shift |Fn1|
* `-----------------------------------------------------------'
- * |Gui|Alt | Fn6 |Alt |Fn7|
+ * |Gui|Alt | Fn4 |Fn5 |Gui|
* `-------------------------------------------'
*/
+ [0] = \
KEYMAP(ESC, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSLS,GRV, \
TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,BSPC, \
- LCTL,A, S, D, F, G, H, J, K, L, FN3, QUOT,FN4, \
- FN5, Z, X, C, V, B, N, M, COMM,DOT, FN2, RSFT,FN1, \
- LGUI,LALT, FN6, RALT,RGUI),
+ LCTL,A, S, D, F, G, H, J, K, L, FN3, QUOT,FN6, \
+ FN7, Z, X, C, V, B, N, M, COMM,DOT, FN2, RSFT,FN1, \
+ LGUI,LALT, FN4, FN5, RGUI),
- /* Layer 1: HHKB mode (HHKB Fn)
+ /* Layer 1: HHKB mode[HHKB Fn]
* ,-----------------------------------------------------------.
* |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
* |-----------------------------------------------------------|
* |Gui|Alt | Space |Alt |Gui|
* `-------------------------------------------'
*/
+ [1] = \
KEYMAP(GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
CAPS,NO, NO, NO, NO, NO, NO, NO, PSCR,SLCK,PAUS, UP, NO, BSPC, \
- LCTL,VOLD,VOLU,MUTE,NO, FN9, PAST,PSLS,HOME,PGUP,LEFT,RGHT,ENT, \
+ LCTL,VOLD,VOLU,MUTE,NO, NO, PAST,PSLS,HOME,PGUP,LEFT,RGHT,ENT, \
LSFT,NO, NO, NO, NO, NO, PPLS,PMNS,END, PGDN,DOWN,RSFT,TRNS, \
LGUI,LALT, SPC, RALT,RGUI),
- /* Layer 2: Vi mode (Slash)
+ /* Layer 2: Vi mode[Slash]
* ,-----------------------------------------------------------.
* |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
* |-----------------------------------------------------------|
* |Gui|Alt | Space |Alt |Gui|
* `-------------------------------------------'
*/
+ [2] = \
KEYMAP(GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
TAB, HOME,PGDN,UP, PGUP,END, HOME,PGDN,PGUP,END, NO, NO, NO, BSPC, \
LCTL,NO, LEFT,DOWN,RGHT,NO, LEFT,DOWN,UP, RGHT,NO, NO, ENT, \
LSFT,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, TRNS,RSFT,NO, \
LGUI,LALT, SPC, RALT,RGUI),
- /* Layer 3: Mouse mode (Semicolon)
+ /* Layer 3: Mouse mode(IJKL)[Semicolon]
+ * ,-----------------------------------------------------------.
+ * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
+ * |-----------------------------------------------------------|
+ * |Tab | | | | | |MwL|MwD|McU|MwU|MwR|Wbk|Wfr|Alt-T|
+ * |-----------------------------------------------------------|
+ * |Contro| | | | | |Mb2|McL|McD|McR|Fn | |Return |
+ * |-----------------------------------------------------------|
+ * |Shift | | | | |Mb3|Mb2|Mb1|Mb4|Mb5| |Shift | |
+ * `-----------------------------------------------------------'
+ * |Gui |Alt | Mb1 |Fn |Fn |
+ * `--------------------------------------------'
+ * Mc: Mouse Cursor / Mb: Mouse Button / Mw: Mouse Wheel8
+ */
+ [3] = \
+ KEYMAP(GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
+ FN8, NO, NO, NO, NO, NO, WH_L,WH_D,MS_U,WH_U,WH_R,WBAK,WFWD,FN8, \
+ LCTL,ACL0,ACL1,ACL2,ACL2,NO, NO, MS_L,MS_D,MS_R,TRNS,NO, ENT, \
+ LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,BTN4,BTN5,NO, RSFT,NO, \
+ LGUI,LALT, BTN1, TRNS,TRNS),
+
+ /* Layer 5: Mouse mode(IJKL)[Space]
+ * ,-----------------------------------------------------------.
+ * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
+ * |-----------------------------------------------------------|
+ * |Tab | | | | | |MwL|MwD|McU|MwU|MwR|Wbk|Wfr|Alt-T|
+ * |-----------------------------------------------------------|
+ * |Contro| | | | | |Mb2|McL|McD|McR|Mb1| |Return |
+ * |-----------------------------------------------------------|
+ * |Shift | | | | |Mb3|Mb2|Mb1|Mb4|Mb5| |Shift | |
+ * `-----------------------------------------------------------'
+ * |Gui |Alt | Mb1 |Fn |Fn |
+ * `--------------------------------------------'
+ * Mc: Mouse Cursor / Mb: Mouse Button / Mw: Mouse Wheel8
+ */
+ [4] = \
+ KEYMAP(GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
+ FN8, NO, NO, NO, NO, NO, WH_L,WH_D,MS_U,WH_U,WH_R,WBAK,WFWD,FN8, \
+ LCTL,VOLD,VOLU,MUTE,NO, NO, NO, MS_L,MS_D,MS_R,BTN1,NO, ENT, \
+ LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,BTN4,BTN5,NO, RSFT,NO, \
+ LGUI,LALT, TRNS, TRNS,TRNS),
+
+#if 0
+ /* Layer 3: Mouse mode(HJKL)[Semicolon]
* ,-----------------------------------------------------------.
* |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
* |-----------------------------------------------------------|
LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,BTN4,BTN5,SLSH,RSFT,NO, \
LGUI,LALT, BTN1, RALT,TRNS),
- /* Layer 4: Matias half-qwerty keyboard style (Space)
+ /* Layer4: Mouse mode(HJKL)[Space]
+ * ,-----------------------------------------------------------.
+ * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
+ * |-----------------------------------------------------------|
+ * |Tab | | | | | |MwL|MwD|MwU|MwR| |Wbk|Wfr|Alt-T|
+ * |-----------------------------------------------------------|
+ * |Contro| | | | | |McL|McD|McU|McR|Fn0| |Return |
+ * |-----------------------------------------------------------|
+ * |Shift | | | | |Mb3|Mb2|Mb1|Mb4|Mb5| |Shift | |
+ * `-----------------------------------------------------------'
+ * |Gui |Alt | Fn0 |Alt |Fn0|
+ * `--------------------------------------------'
+ * Mc: Mouse Cursor / Mb: Mouse Button / Mw: Mouse Wheel
+ */
+ KEYMAP(GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
+ FN8, NO, NO, NO, NO, NO, WH_L,WH_D,WH_U,WH_R,NO, WBAK,WFWD,FN8, \
+ LCTL,NO, ACL0,ACL1,ACL2,NO, MS_L,MS_D,MS_U,MS_R,BTN1,NO, ENT, \
+ LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,BTN4,BTN5,NO, RSFT,NO, \
+ LGUI,LALT, TRNS, RALT,RGUI),
+#endif
+#if 0
+ /* Layer x: Matias half-qwerty keyboard style[Space]
* ,-----------------------------------------------------------.
* | -| 0| 9| 8| 7| 6| 5| 4| 3| 2| 1| | | |Esc|
* |-----------------------------------------------------------|
LCTL,SCLN,L, K, J, H, G, F, D, S, A, RCTL,RCTL, \
LSFT,SLSH,DOT, COMM,M, N, B, V, C, X, Z, RSFT,NO, \
LGUI,LALT, TRNS, RALT,RGUI),
-
- /* Layer5: another Mouse mode (Space)
- * ,-----------------------------------------------------------.
- * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
- * |-----------------------------------------------------------|
- * |Tab | | | | | |MwL|MwD|MwU|MwR| |Wbk|Wfr|Close|
- * |-----------------------------------------------------------|
- * |Contro| | | | | |McL|McD|McU|McR|Fn0| |Return |
- * |-----------------------------------------------------------|
- * |Shift | | | | |Mb3|Mb2|Mb1|Mb4|Mb5| |Shift | |
- * `-----------------------------------------------------------'
- * |Gui |Alt | Fn0 |Alt |Fn0|
- * `--------------------------------------------'
- * Mc: Mouse Cursor / Mb: Mouse Button / Mw: Mouse Wheel
- */
- KEYMAP(ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
- TAB, NO, NO, NO, NO, NO, WH_L,WH_D,WH_U,WH_R,WSTP,WBAK,WFWD,FN8, \
- LCTL,NO, ACL0,ACL1,ACL2,NO, MS_L,MS_D,MS_U,MS_R,NO, NO, ENT, \
- LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,BTN4,BTN5,NO, RSFT,NO, \
- LGUI,LALT, TRNS, RALT,RGUI),
+#endif
};
/* id for user defined functions */
enum function_id {
LSHIFT_LPAREN,
- RSHIFT_RPAREN,
};
enum macro_id {
- LSHIFT_PAREN,
- RSHIFT_PAREN,
HELLO,
VOLUP,
+ ALT_TAB,
};
[1] = ACTION_LAYER_TAP_TOGGLE(1), // HHKB layer(toggle with 5 taps)
[2] = ACTION_LAYER_TAP_KEY(2, KC_SLASH), // Cursor layer with Slash*
[3] = ACTION_LAYER_TAP_KEY(3, KC_SCLN), // Mousekey layer with Semicolon*
- [4] = ACTION_MODS_TAP_KEY(MOD_RCTL, KC_ENT), // RControl with tap Enter*
- [5] = ACTION_MODS_ONESHOT(MOD_LSFT), // Oneshot Shift*
- [6] = ACTION_LAYER_TAP_KEY(5, KC_SPC), // Mousekey layer with Space
- [7] = ACTION_LAYER_TOGGLE(3), // Mousekey layer(toggle)
- [8] = ACTION_MODS_KEY(MOD_LCTL, KC_W), // Close Tab
- [9] = ACTION_MODS_KEY(MOD_LSFT, KC_4), // Shift stuck test
+ [4] = ACTION_LAYER_TAP_KEY(4, KC_SPC), // Mousekey layer with Space
+ [5] = ACTION_LAYER_MOMENTARY(4), // Mousekey layer(IJKL)
+ [6] = ACTION_MODS_TAP_KEY(MOD_RCTL, KC_ENT), // RControl with tap Enter
+ [7] = ACTION_MODS_ONESHOT(MOD_LSFT), // Oneshot Shift
+ [8] = ACTION_MACRO(ALT_TAB), // Application switching
-// [8] = ACTION_LMOD_TAP_KEY(KC_LCTL, KC_BSPC), // LControl with tap Backspace
-// [9] = ACTION_LMOD_TAP_KEY(KC_LCTL, KC_ESC), // LControl with tap Esc
- [11] = ACTION_FUNCTION_TAP(LSHIFT_LPAREN), // Function: LShift with tap '('
- [12] = ACTION_FUNCTION_TAP(RSHIFT_RPAREN), // Function: RShift with tap ')'
-// [13] = ACTION_MACRO_TAP(LSHIFT_PAREN), // Macro: LShift with tap '('
-// [14] = ACTION_MACRO_TAP(RSHIFT_PAREN), // Macro: RShift with tap ')'
-// [15] = ACTION_MACRO(HELLO), // Macro: say hello
-// [9] = ACTION_MACRO(VOLUP), // Macro: media key
+// [x] = ACTION_LMOD_TAP_KEY(KC_LCTL, KC_BSPC), // LControl with tap Backspace
+// [x] = ACTION_LMOD_TAP_KEY(KC_LCTL, KC_ESC), // LControl with tap Esc
+// [x] = ACTION_FUNCTION_TAP(LSHIFT_LPAREN), // Function: LShift with tap '('
+// [x] = ACTION_MACRO(HELLO), // Macro: say hello
+// [x] = ACTION_MACRO(VOLUP), // Macro: media key
};
*/
const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
{
- keyevent_t event = record->event;
- tap_t tap = record->tap;
-
switch (id) {
- case LSHIFT_PAREN:
- if (tap.count > 0 && !tap.interrupted) {
- return (event.pressed ?
- MACRO( D(LSHIFT), D(9), U(9), U(LSHIFT), END ) : MACRO_NONE);
- } else {
- return (event.pressed ?
- MACRO( D(LSHIFT), END ) : MACRO( U(LSHIFT), END ) );
- }
- case RSHIFT_PAREN:
- if (tap.count > 0 && !tap.interrupted) {
- return (event.pressed ?
- MACRO( D(RSHIFT), D(0), U(0), U(RSHIFT), END ) : MACRO_NONE);
- } else {
- return (event.pressed ?
- MACRO( D(RSHIFT), END ) : MACRO( U(RSHIFT), END ) );
- }
case HELLO:
- return (event.pressed ?
+ return (record->event.pressed ?
MACRO( I(0), T(H), T(E), T(L), T(L), W(255), T(O), END ) :
MACRO_NONE );
case VOLUP:
- return (event.pressed ?
+ return (record->event.pressed ?
MACRO( D(VOLU), U(VOLU), END ) :
MACRO_NONE );
+ case ALT_TAB:
+ return (record->event.pressed ?
+ MACRO( D(LALT), D(TAB), END ) :
+ MACRO( U(TAB), END ));
}
return MACRO_NONE;
}
*/
void action_function(keyrecord_t *record, uint8_t id, uint8_t opt)
{
- keyevent_t event = record->event;
- tap_t tap = record->tap;
+ if (record->event.pressed) dprint("P"); else dprint("R");
+ dprintf("%d", record->tap.count);
+ if (record->tap.interrupted) dprint("i");
+ dprint("\n");
switch (id) {
case LSHIFT_LPAREN:
- // LShft + tap '('
- // NOTE: cant use register_code to avoid conflicting with magic key bind
- if (event.pressed) {
- if (tap.count == 0 || tap.interrupted) {
- //add_mods(MOD_BIT(KC_LSHIFT));
- layer_on(1);
+ // Shift parentheses example: LShft + tap '('
+ // http://stevelosh.com/blog/2012/10/a-modern-space-cadet/#shift-parentheses
+ // http://geekhack.org/index.php?topic=41989.msg1304899#msg1304899
+ if (record->event.pressed) {
+ if (record->tap.count > 0 && !record->tap.interrupted) {
+ if (record->tap.interrupted) {
+ dprint("tap interrupted\n");
+ register_mods(MOD_BIT(KC_LSHIFT));
+ }
} else {
- add_mods(MOD_BIT(KC_LSHIFT));
- add_key(KC_9);
- send_keyboard_report();
- del_mods(MOD_BIT(KC_LSHIFT));
- del_key(KC_9);
- send_keyboard_report();
+ register_mods(MOD_BIT(KC_LSHIFT));
}
} else {
- if (tap.count == 0 || tap.interrupted) {
- //del_mods(MOD_BIT(KC_LSHIFT));
- layer_off(1);
- }
- }
- break;
- case RSHIFT_RPAREN:
- // RShift + tap ')'
- if (event.pressed) {
- if (tap.count == 0 || tap.interrupted) {
- add_mods(MOD_BIT(KC_RSHIFT));
- } else {
- add_mods(MOD_BIT(KC_RSHIFT));
- add_key(KC_0);
+ if (record->tap.count > 0 && !(record->tap.interrupted)) {
+ add_weak_mods(MOD_BIT(KC_LSHIFT));
send_keyboard_report();
- del_mods(MOD_BIT(KC_RSHIFT));
- del_key(KC_0);
+ register_code(KC_9);
+ unregister_code(KC_9);
+ del_weak_mods(MOD_BIT(KC_LSHIFT));
send_keyboard_report();
- }
- } else {
- if (tap.count == 0 || tap.interrupted) {
- del_mods(MOD_BIT(KC_RSHIFT));
+ record->tap.count = 0; // ad hoc: cancel tap
+ } else {
+ unregister_mods(MOD_BIT(KC_LSHIFT));
}
}
break;
* `-------------------------------------------'
*/
KEYMAP(GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, TRNS,DEL, \
- TRNS,TRNS,TRNS,ESC, TRNS,TRNS,TRNS,HOME,UP, END, PSCR,SLCK,PAUS,INS, \
+ TRNS,TRNS,TRNS,ESC, TRNS,TRNS,TRNS,HOME,FN3, END, PSCR,SLCK,PAUS,INS, \
TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,PGUP,LEFT,DOWN,RGHT,TRNS,TRNS,TRNS, \
TRNS,TRNS,TRNS,TRNS,TRNS,SPC, PGDN,GRV, FN2, TRNS,TRNS,TRNS,NO, \
TRNS,TRNS, TRNS, TRNS,TRNS),
};
+
+/*
+ * user defined action function
+ */
+enum function_id {
+ CTRL_SPACE_I, // Ctrl + Up(SpaceFN) -> PgUp
+};
+
+void action_function(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+# define MODS_CTRL_MASK (MOD_BIT(KC_LCTRL)|MOD_BIT(KC_RCTRL))
+ static uint8_t ctrl_space_i_prev_ctrl;
+
+ switch (id) {
+ // Ctrl + Up(SpaceFN) -> PgUp
+ case CTRL_SPACE_I:
+ ctrl_space_i_prev_ctrl = get_mods()&MODS_CTRL_MASK;
+ if (record->event.pressed) {
+ if (ctrl_space_i_prev_ctrl) {
+ del_mods(ctrl_space_i_prev_ctrl); // remove Ctrl
+ add_key(KC_PGUP);
+ send_keyboard_report(); // send PgUp without Ctrl
+ add_mods(ctrl_space_i_prev_ctrl); // return Ctrl but not sent
+ } else {
+ add_key(KC_UP);
+ send_keyboard_report();
+ }
+ } else {
+ if (ctrl_space_i_prev_ctrl) {
+ del_key(KC_PGUP);
+ send_keyboard_report();
+ } else {
+ del_key(KC_UP);
+ send_keyboard_report();
+ }
+ }
+ break;
+ }
+}
+
+
/*
* Fn action definition
*/
[0] = ACTION_LAYER_MOMENTARY(1),
[1] = ACTION_LAYER_TAP_KEY(2, KC_SPACE),
[2] = ACTION_MODS_KEY(MOD_LSFT, KC_GRV), // tilde
+ [3] = ACTION_FUNCTION(CTRL_SPACE_I), // Ctrl + Up(SpaceFN) -> PgUp
};
-
--- /dev/null
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+# Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+# (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+# have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+# have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+# (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+# (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging,
+# with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+# bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = kittenpaw_lufa
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# List C source files here. (C dependencies are automatically generated.)
+SRC = keymap.c \
+ matrix.c \
+ led.c
+
+CONFIG_H = config.h
+
+# MCU name
+MCU = atmega32u2
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+# Build Options
+# comment out to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+#CONSOLE_ENABLE = yes # Console for debug(+400)
+COMMAND_ENABLE = yes # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
+#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
+
+
+# Boot Section Size in bytes
+# Teensy halfKay 512
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+include $(TOP_DIR)/protocol/lufa.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk
--- /dev/null
+Kitten Paw controller firmware
+======================
+Custom controller for the Costar Majestouch keyboard designed by bpiphany.
+
+*Note that this is not the official firmware*
+
+Build
+-----
+Move to this directory then just run `make` like:
+
+ $ make -f Makefile.lufa
+
+At the moment only the LUFA stack is supported.
+
+
+Bootloader
+---------
+To enter bootloader by hardware use a magnet above the controller before connecting the usb cable.
+
+It is still possible to use Boot Magic and Command (LSFT+RSFT+PAUS) to access the bootloader though.
--- /dev/null
+/*
+Copyright 2014 Ralf Schmitt <ralf@bunkertor.net>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x6050
+#define DEVICE_VER 0x0104
+#define MANUFACTURER Costar
+#define PRODUCT Majestouch
+
+/* message strings */
+#define DESCRIPTION t.m.k. keyboard firmware for Majestouch
+
+/* matrix size */
+#define MATRIX_ROWS 8
+#define MATRIX_COLS 18
+
+/* Set 0 if need no debouncing */
+#define DEBOUNCE 5
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+#endif
--- /dev/null
+/*
+Copyright 2014 Ralf Schmitt <ralf@bunkertor.net>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <avr/pgmspace.h>
+#include "keycode.h"
+#include "action.h"
+#include "action_macro.h"
+#include "report.h"
+#include "host.h"
+#include "debug.h"
+#include "keymap.h"
+
+/*
+ Matrix col/row mapping
+
+ ,----. ,-------------------. ,-------------------. ,-------------------. ,--------------.
+ |06/6| |07/4|08/4|08/2|08/6| |15/5|11/6|12/2|12/4| |14/4|14/5|14/6|14/0| |13/5|13/7|15/7|
+ `----' `-------------------' `-------------------' `-------------------' `--------------'
+ ,-------------------------------------------------------------------------. ,--------------. ,-------------------.
+ |06/4|06/5|07/5|08/5|09/5|09/4|10/4|10/5|11/5|12/5|05/5|05/4|11/4| 14/2| |17/4|02/4|04/4| |16/1|17/1|04/1|04/0|
+ |-------------------------------------------------------------------------| |--------------| |-------------------|
+ |06/2 |06/7|07/7|08/7|09/7|09/2|10/2|10/7|11/7|12/7|05/7|05/2|11/2| 14/3| |16/4|02/5|04/5| |16/7|17/7|04/7| |
+ |-------------------------------------------------------------------------| '--------------' |-------------- 02/7|
+ |02/7 |06/3|07/3|08/3|09/3|09/6|10/6|10/3|11/3|12/3|05/3|05/6| 14/1| |16/2|17/2|04/2| |
+ |-------------------------------------------------------------------------| ,----. |-------------------|
+ |01/2 |06/1|07/1|08/1|09/1|09/0|10/0|10/1|11/1|12/1|05/0| 01/3| |02/6| |16/3|17/3|04/3| |
+ |-------------------------------------------------------------------------| ,--------------. |-------------- 02/3|
+ |15/4|03/2|13/6| 16/6 |13/0|0/3|12/0|15/1| |02/0|16/0|17/0| | 17/6 |04/6| |
+ `-------------------------------------------------------------------------' `--------------' `-------------------'
+*/
+
+#define KEYMAP( \
+ KG6, KH4, KI4, KI2, KI6, KP5, KL6, KM2, KM4, KO4, KO5, KO6, KO0, KN5, KN7, KP7, \
+ KG4, KG5, KH5, KI5, KJ5, KJ4, KK4, KK5, KL5, KM5, KF5, KF4, KL4, KO2, KR4, KC4, KE4, KQ1, KR1, KE1, KE0, \
+ KG2, KG7, KH7, KI7, KJ7, KJ2, KK2, KK7, KL7, KM7, KF7, KF2, KL2, KO3, KQ4, KC5, KE5, KQ7, KR7, KE7, KC7, \
+ KH2, KG3, KH3, KI3, KJ3, KJ6, KK6, KK3, KL3, KM3, KF3, KF6, KO1, KQ2, KR2, KE2, \
+ KB2, KH6, KG1, KH1, KI1, KJ1, KJ0, KK0, KK1, KL1, KM1, KF0, KB3, KC6, KQ3, KR3, KE3, KC3, \
+ KP4, KD2, KN6, KQ6, KN0, KA3, KM0, KP1, KC0, KQ0, KR0, KR6, KE6 \
+) { \
+/* 0 1 2 3 4 5 6 7 */ \
+/* A 0 */ {KC_NO, KC_NO, KC_NO, KC_##KA3, KC_NO, KC_NO, KC_NO, KC_NO },\
+/* B 1 */ {KC_NO, KC_NO, KC_##KB2, KC_##KB3, KC_NO, KC_NO, KC_NO, KC_NO },\
+/* C 2 */ {KC_##KC0, KC_NO, KC_NO, KC_##KC3, KC_##KC4, KC_##KC5, KC_##KC6, KC_##KC7},\
+/* D 3 */ {KC_NO, KC_NO, KC_##KD2, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO },\
+/* E 4 */ {KC_##KE0, KC_##KE1, KC_##KE2, KC_##KE3, KC_##KE4, KC_##KE5, KC_##KE6, KC_##KE7},\
+/* F 5 */ {KC_##KF0, KC_NO, KC_##KF2, KC_##KF3, KC_##KF4, KC_##KF5, KC_##KF6, KC_##KF7},\
+/* G 6 */ {KC_NO, KC_##KG1, KC_##KG2, KC_##KG3, KC_##KG4, KC_##KG5, KC_##KG6, KC_##KG7},\
+/* H 7 */ {KC_NO, KC_##KH1, KC_##KH2, KC_##KH3, KC_##KH4, KC_##KH5, KC_##KH6, KC_##KH7},\
+/* I 8 */ {KC_NO, KC_##KI1, KC_##KI2, KC_##KI3, KC_##KI4, KC_##KI5, KC_##KI6, KC_##KI7},\
+/* J 9 */ {KC_##KJ0, KC_##KJ1, KC_##KJ2, KC_##KJ3, KC_##KJ4, KC_##KJ5, KC_##KJ6, KC_##KJ7},\
+/* K 10 */ {KC_##KK0, KC_##KK1, KC_##KK2, KC_##KK3, KC_##KK4, KC_##KK5, KC_##KK6, KC_##KK7},\
+/* L 11 */ {KC_NO, KC_##KL1, KC_##KL2, KC_##KL3, KC_##KL4, KC_##KL5, KC_##KL6, KC_##KL7},\
+/* M 12 */ {KC_##KM0, KC_##KM1, KC_##KM2, KC_##KM3, KC_##KM4, KC_##KM5, KC_NO, KC_##KM7},\
+/* N 13 */ {KC_##KN0, KC_NO, KC_NO, KC_NO, KC_NO, KC_##KN5, KC_##KN6, KC_##KN7},\
+/* O 14 */ {KC_##KO0, KC_##KO1, KC_##KO2, KC_##KO3, KC_##KO4, KC_##KO5, KC_##KO6, KC_NO },\
+/* P 15 */ {KC_NO, KC_##KP1, KC_NO, KC_NO, KC_##KP4, KC_##KP5, KC_NO, KC_##KP7},\
+/* Q 16 */ {KC_##KQ0, KC_##KQ1, KC_##KQ2, KC_##KQ3, KC_##KQ4, KC_NO, KC_##KQ6, KC_##KQ7},\
+/* R 17 */ {KC_##KR0, KC_##KR1, KC_##KR2, KC_##KR3, KC_##KR4, KC_NO, KC_##KR6, KC_##KR7} \
+}
+
+#include "keymap_ansi.h"
+
+#define KEYMAPS_SIZE (sizeof(keymaps) / sizeof(keymaps[0]))
+#define FN_ACTIONS_SIZE (sizeof(fn_actions) / sizeof(fn_actions[0]))
+
+/* translates key to keycode */
+uint8_t keymap_key_to_keycode(uint8_t layer, key_t key)
+{
+ if (layer < KEYMAPS_SIZE) {
+ return pgm_read_byte(&keymaps[(layer)][(key.col)][(key.row)]);
+ } else {
+ return pgm_read_byte(&keymaps[0][(key.col)][(key.row)]);
+ }
+}
+
+/* translates Fn keycode to action */
+action_t keymap_fn_to_action(uint8_t keycode)
+{
+ action_t action;
+ if (FN_INDEX(keycode) < FN_ACTIONS_SIZE) {
+ action.code = pgm_read_word(&fn_actions[FN_INDEX(keycode)]);
+ } else {
+ action.code = ACTION_NO;
+ }
+ return action;
+}
--- /dev/null
+
+static const uint8_t PROGMEM keymaps[][MATRIX_COLS][MATRIX_ROWS] = {
+ /* Layer 0: Standard ANSI layer */
+ KEYMAP(\
+ ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, PSCR,SLCK,PAUS, \
+ GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS, EQL,BSPC, INS, HOME,PGUP, NLCK,PSLS,PAST,PMNS, \
+ TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,BSLS, DEL, END, PGDN, P7, P8, P9, PPLS, \
+ CAPS,A, S, D, F, G, H, J, K, L, SCLN,QUOT, ENT, P4, P5, P6, \
+ LSFT,NUBS,Z, X, C, V, B, N, M, COMM,DOT, SLSH, RSFT, UP, P1, P2, P3, PENT, \
+ LCTL,LGUI,LALT, SPC, RALT,RGUI, FN0,RCTL, LEFT,DOWN,RGHT, P0, PDOT), \
+ /* Layer 1: Function layer */
+ KEYMAP(\
+ CALC,MYCM,WSCH,WHOM,MAIL,VOLD,VOLU,MSEL,MSTP,MPLY,MPRV,MNXT,TRNS, WAKE, PWR,SLEP, \
+ TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, TRNS,TRNS,TRNS, TRNS,TRNS,TRNS,TRNS, \
+ TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, TRNS,TRNS,TRNS, TRNS,TRNS,TRNS,TRNS, \
+ TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, TRNS, TRNS,TRNS,TRNS, \
+ TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, TRNS, TRNS, TRNS,TRNS,TRNS,TRNS, \
+ TRNS,TRNS,TRNS, TRNS, TRNS,TRNS,TRNS,TRNS, TRNS,TRNS,TRNS, TRNS,TRNS)
+};
+
+static const uint16_t PROGMEM fn_actions[] = {
+ [0] = ACTION_LAYER_MOMENTARY(1)
+};
--- /dev/null
+/*
+Copyright 2014 Ralf Schmitt <ralf@bunkertor.net>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include <avr/io.h>
+#include "stdint.h"
+#include "led.h"
+
+/* LED pin configuration
+ *
+ * Scroll Lock PB7
+ * CAPS PC6
+ * NUMLOCK PC5
+ *
+ */
+void led_set(uint8_t usb_led)
+{
+ DDRB |= (1<<7);
+ DDRC |= (1<<5) | (1<<6);
+
+ if (usb_led & (1<<USB_LED_CAPS_LOCK))
+ {
+ PORTC &= ~(1<<6);
+ }
+ else
+ {
+ PORTC |= (1<<6);
+ }
+
+ if (usb_led & (1<<USB_LED_NUM_LOCK))
+ {
+ PORTC &= ~(1<<5);
+ }
+ else
+ {
+ PORTC |= (1<<5);
+ }
+
+ if (usb_led & (1<<USB_LED_SCROLL_LOCK))
+ {
+ PORTB &= ~(1<<7);
+ }
+ else
+ {
+ PORTB |= (1<<7);
+ }
+}
--- /dev/null
+/*
+Copyright 2014 Ralf Schmitt <ralf@bunkertor.net>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <avr/io.h>
+#include <util/delay.h>
+#include "print.h"
+#include "debug.h"
+#include "util.h"
+#include "matrix.h"
+
+#ifndef DEBOUNCE
+# define DEBOUNCE 0
+#endif
+static uint8_t debouncing = DEBOUNCE;
+
+static matrix_row_t matrix[MATRIX_ROWS];
+static matrix_row_t matrix_debouncing[MATRIX_ROWS];
+
+static uint8_t read_rows(void);
+static void init_rows(void);
+static void unselect_cols(void);
+static void select_col(uint8_t col);
+
+inline uint8_t matrix_rows(void)
+{
+ return MATRIX_ROWS;
+}
+
+inline uint8_t matrix_cols(void)
+{
+ return MATRIX_COLS;
+}
+
+void matrix_init(void)
+{
+ unselect_cols();
+ init_rows();
+ for (uint8_t i=0; i < MATRIX_ROWS; i++) {
+ matrix[i] = 0;
+ matrix_debouncing[i] = 0;
+ }
+}
+
+uint8_t matrix_scan(void)
+{
+ for (uint8_t col = 0; col < MATRIX_COLS; col++) {
+ select_col(col);
+ _delay_us(3);
+ uint8_t rows = read_rows();
+ for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
+ bool prev_bit = matrix_debouncing[row] & ((matrix_row_t)1<<col);
+ bool curr_bit = rows & (1<<row);
+ if (prev_bit != curr_bit) {
+ matrix_debouncing[row] ^= ((matrix_row_t)1<<col);
+ debouncing = DEBOUNCE;
+ }
+ }
+ unselect_cols();
+ }
+
+ if (debouncing) {
+ if (--debouncing) {
+ _delay_ms(1);
+ } else {
+ for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+ matrix[i] = matrix_debouncing[i];
+ }
+ }
+ }
+
+ return 1;
+}
+
+bool matrix_is_modified(void)
+{
+ if (debouncing) return false;
+ return true;
+}
+
+inline bool matrix_is_on(uint8_t row, uint8_t col)
+{
+ return (matrix[row] & ((matrix_row_t)1<<col));
+}
+
+inline matrix_row_t matrix_get_row(uint8_t row)
+{
+ return matrix[row];
+}
+
+void matrix_print(void)
+{
+ print("\nr/c 0123456789ABCDEF\n");
+ for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
+ xprintf("%02X: %032lb\n", row, bitrev32(matrix_get_row(row)));
+ }
+}
+
+uint8_t matrix_key_count(void)
+{
+ uint8_t count = 0;
+ for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+ count += bitpop32(matrix[i]);
+ }
+ return count;
+}
+
+/* Row pin configuration
+ *
+ * row: 0 1 2 3 4 5 6 7
+ * pin: PC2 PB1 PB2 PB3 PC7 PB4 PB5 PB6
+ *
+ */
+static void init_rows(void)
+{
+ DDRC &= ~0b10000100;
+ DDRB &= ~0b01111110;
+ PORTC |= 0b10000100;
+ PORTB |= 0b01111110;
+}
+
+static uint8_t read_rows(void)
+{
+ return (PINC&(1<<2) ? 0 : (1<<0)) |
+ (PINB&(1<<1) ? 0 : (1<<1)) |
+ (PINB&(1<<2) ? 0 : (1<<2)) |
+ (PINB&(1<<3) ? 0 : (1<<3)) |
+ (PINC&(1<<7) ? 0 : (1<<4)) |
+ (PINB&(1<<4) ? 0 : (1<<5)) |
+ (PINB&(1<<5) ? 0 : (1<<6)) |
+ (PINB&(1<<6) ? 0 : (1<<7));
+}
+
+/* These columns uses two 74HC42 4 to 10 bit demultiplexers (low active).
+ *
+ * COL PD1 PD0 PD2 PD6 PD5 PD4
+ * 12 1 1 0 0 0 0
+ * 11 1 1 0 0 0 1
+ * 10 1 1 0 0 1 0
+ * 9 1 1 0 0 1 1
+ * 8 1 1 0 1 0 0
+ * 7 1 1 0 1 0 1
+ * 6 1 1 0 1 1 0
+ * 5 1 1 0 1 1 1
+ * 4 1 1 1 0 0 0
+ * 3 1 1 1 0 0 1
+
+ * COL PD2 PD6 PD1 PD0 PD5 PD4
+ * 2 1 1 0 0 0 0
+ * 1 1 1 0 0 0 1
+ * 0 1 1 0 0 1 0
+ * 17 1 1 0 0 1 1
+ * 16 1 1 0 1 0 0
+ * 1 1 0 1 0 1
+ * 1 1 0 1 1 0
+ * 15 1 1 0 1 1 1
+ * 14 1 1 1 0 0 0
+ * 13 1 1 1 0 0 1
+ */
+static void unselect_cols(void)
+{
+ DDRD |= 0b01110111;
+ PORTD &= ~0b01110111;
+}
+
+static void select_col(uint8_t col)
+{
+ switch (col) {
+ case 0:
+ PORTD |= (1<<5) | (1<<6) | (1<<2);
+ break;
+ case 1:
+ PORTD |= (1<<4) | (1<<6) | (1<<2);
+ break;
+ case 2:
+ PORTD |= (1<<6) | (1<<2);
+ break;
+ case 3:
+ PORTD |= (1<<4) | (1<<2) | (1<<0) | (1<<1);
+ break;
+ case 4:
+ PORTD |= (1<<2) | (1<<0) | (1<<1);
+ break;
+ case 5:
+ PORTD |= (1<<4) | (1<<5) | (1<<6) | (1<<0) | (1<<1);
+ break;
+ case 6:
+ PORTD |= (1<<5) | (1<<6) | (1<<0) | (1<<1);
+ break;
+ case 7:
+ PORTD |= (1<<4) | (1<<6) | (1<<0) | (1<<1);
+ break;
+ case 8:
+ PORTD |= (1<<6) | (1<<0) | (1<<1);
+ break;
+ case 9:
+ PORTD |= (1<<4) | (1<<5) | (1<<0) | (1<<1);
+ break;
+ case 10:
+ PORTD |= (1<<5) | (1<<0) | (1<<1);
+ break;
+ case 11:
+ PORTD |= (1<<4) | (1<<0) | (1<<1);
+ break;
+ case 12:
+ PORTD |= (1<<0) | (1<<1);
+ break;
+ case 13:
+ PORTD |= (1<<4) | (1<<1) | (1<<6) | (1<<2);
+ break;
+ case 14:
+ PORTD |= (1<<1) | (1<<6) | (1<<2);
+ break;
+ case 15:
+ PORTD |= (1<<4) | (1<<5) | (1<<0) | (1<<6) | (1<<2);
+ break;
+ case 16:
+ PORTD |= (1<<0) | (1<<6) | (1<<2);
+ break;
+ case 17:
+ PORTD |= (1<<4) | (1<<5) | (1<<6) | (1<<2);
+ break;
+ }
+}
LUFA_DIR = protocol/lufa
# Path to the LUFA library
-LUFA_PATH ?= protocol/lufa/LUFA-120730
+ifeq (, $(wildcard $(TOP_DIR)/$(LUFA_DIR)/LUFA-git/LUFA/Version.h))
+ LUFA_PATH ?= $(LUFA_DIR)/LUFA-120730
+else
+ LUFA_PATH ?= $(LUFA_DIR)/LUFA-git
+endif
+
# Create the LUFA source path variables by including the LUFA makefile
ifneq (, $(wildcard $(TOP_DIR)/$(LUFA_PATH)/LUFA/Build/lufa_sources.mk))
#endif
# LUFA library compile-time options and predefined tokens
-LUFA_OPTS = -D USB_DEVICE_ONLY
-LUFA_OPTS += -D USE_FLASH_DESCRIPTORS
-LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
+LUFA_OPTS = -DUSB_DEVICE_ONLY
+LUFA_OPTS += -DUSE_FLASH_DESCRIPTORS
+LUFA_OPTS += -DUSE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
+#LUFA_OPTS += -DINTERRUPT_CONTROL_ENDPOINT
+LUFA_OPTS += -DFIXED_CONTROL_ENDPOINT_SIZE=8
+LUFA_OPTS += -DFIXED_NUM_CONFIGURATIONS=1
OPT_DEFS += -DF_USB=$(F_USB)UL
OPT_DEFS += -DARCH=ARCH_$(ARCH)
--- /dev/null
+Subproject commit b6c18b2a7c544653efbe12a1d4e8ba65e7d83c35
{
.Header = {.Size = sizeof(USB_Descriptor_Device_t), .Type = DTYPE_Device},
- .USBSpecification = VERSION_BCD(01.10),
+ .USBSpecification = VERSION_BCD(1,1,0),
.Class = USB_CSCP_NoDeviceClass,
.SubClass = USB_CSCP_NoDeviceSubclass,
.Protocol = USB_CSCP_NoDeviceProtocol,
- .Endpoint0Size = 8,
+ .Endpoint0Size = FIXED_CONTROL_ENDPOINT_SIZE,
/* specified in config.h */
.VendorID = VENDOR_ID,
.ProductStrIndex = 0x02,
.SerialNumStrIndex = NO_DESCRIPTOR,
- .NumberOfConfigurations = 1
+ .NumberOfConfigurations = FIXED_NUM_CONFIGURATIONS
};
/*******************************************************************************
{
.Header = {.Size = sizeof(USB_HID_Descriptor_HID_t), .Type = HID_DTYPE_HID},
- .HIDSpec = VERSION_BCD(01.11),
+ .HIDSpec = VERSION_BCD(1,1,1),
.CountryCode = 0x00,
.TotalReportDescriptors = 1,
.HIDReportType = HID_DTYPE_Report,
.EndpointAddress = (ENDPOINT_DIR_IN | KEYBOARD_IN_EPNUM),
.Attributes = (EP_TYPE_INTERRUPT | ENDPOINT_ATTR_NO_SYNC | ENDPOINT_USAGE_DATA),
.EndpointSize = KEYBOARD_EPSIZE,
- .PollingIntervalMS = 0x01
+ .PollingIntervalMS = 0x0A
},
/*
{
.Header = {.Size = sizeof(USB_HID_Descriptor_HID_t), .Type = HID_DTYPE_HID},
- .HIDSpec = VERSION_BCD(01.11),
+ .HIDSpec = VERSION_BCD(1,1,1),
.CountryCode = 0x00,
.TotalReportDescriptors = 1,
.HIDReportType = HID_DTYPE_Report,
.EndpointAddress = (ENDPOINT_DIR_IN | MOUSE_IN_EPNUM),
.Attributes = (EP_TYPE_INTERRUPT | ENDPOINT_ATTR_NO_SYNC | ENDPOINT_USAGE_DATA),
.EndpointSize = MOUSE_EPSIZE,
- .PollingIntervalMS = 0x01
+ .PollingIntervalMS = 0x0A
},
#endif
{
.Header = {.Size = sizeof(USB_HID_Descriptor_HID_t), .Type = HID_DTYPE_HID},
- .HIDSpec = VERSION_BCD(01.11),
+ .HIDSpec = VERSION_BCD(1,1,1),
.CountryCode = 0x00,
.TotalReportDescriptors = 1,
.HIDReportType = HID_DTYPE_Report,
.EndpointAddress = (ENDPOINT_DIR_IN | EXTRAKEY_IN_EPNUM),
.Attributes = (EP_TYPE_INTERRUPT | ENDPOINT_ATTR_NO_SYNC | ENDPOINT_USAGE_DATA),
.EndpointSize = EXTRAKEY_EPSIZE,
- .PollingIntervalMS = 0x01
+ .PollingIntervalMS = 0x0A
},
#endif
{
.Header = {.Size = sizeof(USB_HID_Descriptor_HID_t), .Type = HID_DTYPE_HID},
- .HIDSpec = VERSION_BCD(01.11),
+ .HIDSpec = VERSION_BCD(1,1,1),
.CountryCode = 0x00,
.TotalReportDescriptors = 1,
.HIDReportType = HID_DTYPE_Report,
{
.Header = {.Size = sizeof(USB_HID_Descriptor_HID_t), .Type = HID_DTYPE_HID},
- .HIDSpec = VERSION_BCD(01.11),
+ .HIDSpec = VERSION_BCD(1,1,1),
.CountryCode = 0x00,
.TotalReportDescriptors = 1,
.HIDReportType = HID_DTYPE_Report,
#ifdef CONSOLE_ENABLE
# define CONSOLE_IN_EPNUM (EXTRAKEY_IN_EPNUM + 1)
-# define CONSOLE_OUT_EPNUM (EXTRAKEY_IN_EPNUM + 2)
+# define CONSOLE_OUT_EPNUM (EXTRAKEY_IN_EPNUM + 1)
+//# define CONSOLE_OUT_EPNUM (EXTRAKEY_IN_EPNUM + 2)
#else
# define CONSOLE_OUT_EPNUM EXTRAKEY_IN_EPNUM
#endif
#ifdef NKRO_ENABLE
# define NKRO_IN_EPNUM (CONSOLE_OUT_EPNUM + 1)
+# if defined(__AVR_ATmega32U2__) && NKRO_IN_EPNUM > 4
+# error "Endpoints are not available enough to support all functions. Remove some in Makefile.(MOUSEKEY, EXTRAKEY, CONSOLE, NKRO)"
+# endif
#endif
const void** const DescriptorAddress)
ATTR_WARN_UNUSED_RESULT ATTR_NON_NULL_PTR_ARG(3);
+
+/* new API */
+#if LUFA_VERSION_INTEGER < 0x140302
+ #undef VERSION_BCD
+ #define VERSION_BCD(Major, Minor, Revision) \
+ CPU_TO_LE16( ((Major & 0xFF) << 8) | \
+ ((Minor & 0x0F) << 4) | \
+ (Revision & 0x0F) )
+#endif
+
#endif
#include "descriptor.h"
#include "lufa.h"
-static uint8_t idle_duration = 0;
-static uint8_t protocol_report = 1;
+uint8_t keyboard_idle = 0;
+uint8_t keyboard_protocol = 1;
static uint8_t keyboard_led_stats = 0;
static report_keyboard_t keyboard_report_sent;
/** Event handler for the USB_ConfigurationChanged event.
* This is fired when the host sets the current configuration of the USB device after enumeration.
*/
-#if LUFA_VERSION_INTEGER < 0x120730
- /* old API 120219 */
- #define ENDPOINT_CONFIG(epnum, eptype, epdir, epsize, epbank) Endpoint_ConfigureEndpoint(epnum, eptype, epdir, epsize, epbank)
-#else
- /* new API >= 120730 */
- #define ENDPOINT_BANK_SINGLE 1
- #define ENDPOINT_BANK_DOUBLE 2
- #define ENDPOINT_CONFIG(epnum, eptype, epdir, epsize, epbank) Endpoint_ConfigureEndpoint((epdir) | (epnum) , eptype, epsize, epbank)
-#endif
void EVENT_USB_Device_ConfigurationChanged(void)
{
bool ConfigSuccess = true;
/* Setup Console HID Report Endpoints */
ConfigSuccess &= ENDPOINT_CONFIG(CONSOLE_IN_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_IN,
CONSOLE_EPSIZE, ENDPOINT_BANK_DOUBLE);
+#if 0
ConfigSuccess &= ENDPOINT_CONFIG(CONSOLE_OUT_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_OUT,
CONSOLE_EPSIZE, ENDPOINT_BANK_SINGLE);
#endif
+#endif
#ifdef NKRO_ENABLE
/* Setup NKRO HID Report Endpoints */
// Interface
switch (USB_ControlRequest.wIndex) {
case KEYBOARD_INTERFACE:
+ case NKRO_INTERFACE:
Endpoint_ClearSETUP();
while (!(Endpoint_IsOUTReceived())) {
case HID_REQ_GetProtocol:
if (USB_ControlRequest.bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
{
- Endpoint_ClearSETUP();
- while (!(Endpoint_IsINReady()));
- Endpoint_Write_8(protocol_report);
- Endpoint_ClearIN();
- Endpoint_ClearStatusStage();
+ if (USB_ControlRequest.wIndex == KEYBOARD_INTERFACE) {
+ Endpoint_ClearSETUP();
+ while (!(Endpoint_IsINReady()));
+ Endpoint_Write_8(keyboard_protocol);
+ Endpoint_ClearIN();
+ Endpoint_ClearStatusStage();
+ }
}
break;
case HID_REQ_SetProtocol:
if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
{
- Endpoint_ClearSETUP();
- Endpoint_ClearStatusStage();
+ if (USB_ControlRequest.wIndex == KEYBOARD_INTERFACE) {
+ Endpoint_ClearSETUP();
+ Endpoint_ClearStatusStage();
- protocol_report = ((USB_ControlRequest.wValue & 0xFF) != 0x00);
+ keyboard_protocol = ((USB_ControlRequest.wValue & 0xFF) != 0x00);
+#ifdef NKRO_ENABLE
+ keyboard_nkro = !!keyboard_protocol;
+#endif
+ clear_keyboard();
+ }
}
break;
Endpoint_ClearSETUP();
Endpoint_ClearStatusStage();
- idle_duration = ((USB_ControlRequest.wValue & 0xFF00) >> 8);
+ keyboard_idle = ((USB_ControlRequest.wValue & 0xFF00) >> 8);
}
break;
{
Endpoint_ClearSETUP();
while (!(Endpoint_IsINReady()));
- Endpoint_Write_8(idle_duration);
+ Endpoint_Write_8(keyboard_idle);
Endpoint_ClearIN();
Endpoint_ClearStatusStage();
}
static void send_keyboard(report_keyboard_t *report)
{
- uint8_t timeout = 0;
+ uint8_t timeout = 255;
if (USB_DeviceState != DEVICE_STATE_Configured)
return;
/* Select the Keyboard Report Endpoint */
#ifdef NKRO_ENABLE
if (keyboard_nkro) {
+ /* Report protocol - NKRO */
Endpoint_SelectEndpoint(NKRO_IN_EPNUM);
- }
- else
-#endif
- {
- Endpoint_SelectEndpoint(KEYBOARD_IN_EPNUM);
- }
- /* Check if Keyboard Endpoint Ready for Read/Write */
- while (--timeout && !Endpoint_IsReadWriteAllowed()) ;
+ /* Check if write ready for a polling interval around 1ms */
+ while (timeout-- && !Endpoint_IsReadWriteAllowed()) _delay_us(4);
+ if (!Endpoint_IsReadWriteAllowed()) return;
- /* Write Keyboard Report Data */
-#ifdef NKRO_ENABLE
- if (keyboard_nkro) {
+ /* Write Keyboard Report Data */
Endpoint_Write_Stream_LE(report, NKRO_EPSIZE, NULL);
}
else
#endif
{
- /* boot mode */
+ /* Boot protocol */
+ Endpoint_SelectEndpoint(KEYBOARD_IN_EPNUM);
+
+ /* Check if write ready for a polling interval around 10ms */
+ while (timeout-- && !Endpoint_IsReadWriteAllowed()) _delay_us(40);
+ if (!Endpoint_IsReadWriteAllowed()) return;
+
+ /* Write Keyboard Report Data */
Endpoint_Write_Stream_LE(report, KEYBOARD_EPSIZE, NULL);
}
static void send_mouse(report_mouse_t *report)
{
#ifdef MOUSE_ENABLE
- uint8_t timeout = 0;
+ uint8_t timeout = 255;
if (USB_DeviceState != DEVICE_STATE_Configured)
return;
/* Select the Mouse Report Endpoint */
Endpoint_SelectEndpoint(MOUSE_IN_EPNUM);
- /* Check if Mouse Endpoint Ready for Read/Write */
- while (--timeout && !Endpoint_IsReadWriteAllowed()) ;
+ /* Check if write ready for a polling interval around 10ms */
+ while (timeout-- && !Endpoint_IsReadWriteAllowed()) _delay_us(40);
+ if (!Endpoint_IsReadWriteAllowed()) return;
/* Write Mouse Report Data */
Endpoint_Write_Stream_LE(report, sizeof(report_mouse_t), NULL);
static void send_system(uint16_t data)
{
- uint8_t timeout = 0;
+ uint8_t timeout = 255;
if (USB_DeviceState != DEVICE_STATE_Configured)
return;
.usage = data
};
Endpoint_SelectEndpoint(EXTRAKEY_IN_EPNUM);
- while (--timeout && !Endpoint_IsReadWriteAllowed()) ;
+
+ /* Check if write ready for a polling interval around 10ms */
+ while (timeout-- && !Endpoint_IsReadWriteAllowed()) _delay_us(40);
+ if (!Endpoint_IsReadWriteAllowed()) return;
+
Endpoint_Write_Stream_LE(&r, sizeof(report_extra_t), NULL);
Endpoint_ClearIN();
}
static void send_consumer(uint16_t data)
{
- uint8_t timeout = 0;
+ uint8_t timeout = 255;
if (USB_DeviceState != DEVICE_STATE_Configured)
return;
.usage = data
};
Endpoint_SelectEndpoint(EXTRAKEY_IN_EPNUM);
- while (--timeout && !Endpoint_IsReadWriteAllowed()) ;
+
+ /* Check if write ready for a polling interval around 10ms */
+ while (timeout-- && !Endpoint_IsReadWriteAllowed()) _delay_us(40);
+ if (!Endpoint_IsReadWriteAllowed()) return;
+
Endpoint_Write_Stream_LE(&r, sizeof(report_extra_t), NULL);
Endpoint_ClearIN();
}
uint16_t usage;
} __attribute__ ((packed)) report_extra_t;
+
+#if LUFA_VERSION_INTEGER < 0x120730
+ /* old API 120219 */
+ #define ENDPOINT_CONFIG(epnum, eptype, epdir, epsize, epbank) Endpoint_ConfigureEndpoint(epnum, eptype, epdir, epsize, epbank)
+#else
+ /* new API >= 120730 */
+ #define ENDPOINT_BANK_SINGLE 1
+ #define ENDPOINT_BANK_DOUBLE 2
+ #define ENDPOINT_CONFIG(epnum, eptype, epdir, epsize, epbank) Endpoint_ConfigureEndpoint((epdir) | (epnum) , eptype, epsize, epbank)
+#endif
+
#endif
#include "sleep_led.h"
#endif
#include "suspend.h"
+#include "action.h"
#include "action_util.h"
void usb_remote_wakeup(void)
{
UDCON |= (1<<RMWKUP);
+ while (UDCON & (1<<RMWKUP));
}
}
/* TODO: should keep IDLE rate on each keyboard interface */
#ifdef NKRO_ENABLE
- if (!keyboard_nkro && usb_keyboard_idle_config && (++div4 & 3) == 0) {
+ if (!keyboard_nkro && keyboard_idle && (++div4 & 3) == 0) {
#else
- if (usb_keyboard_idle_config && (++div4 & 3) == 0) {
+ if (keyboard_idle && (++div4 & 3) == 0) {
#endif
UENUM = KBD_ENDPOINT;
if (UEINTX & (1<<RWAL)) {
usb_keyboard_idle_count++;
- if (usb_keyboard_idle_count == usb_keyboard_idle_config) {
+ if (usb_keyboard_idle_count == keyboard_idle) {
usb_keyboard_idle_count = 0;
/* TODO: fix keyboard_report inconsistency */
/* To avoid Mac SET_IDLE behaviour.
UEDATX = keyboard_report_prev->mods;
UEDATX = 0;
- uint8_t keys = usb_keyboard_protocol ? KBD_REPORT_KEYS : 6;
+ uint8_t keys = keyboard_protocol ? KBD_REPORT_KEYS : 6;
for (uint8_t i=0; i<keys; i++) {
UEDATX = keyboard_report_prev->keys[i];
}
}
if (bRequest == HID_GET_IDLE) {
usb_wait_in_ready();
- UEDATX = usb_keyboard_idle_config;
+ UEDATX = keyboard_idle;
usb_send_in();
return;
}
if (bRequest == HID_GET_PROTOCOL) {
usb_wait_in_ready();
- UEDATX = usb_keyboard_protocol;
+ UEDATX = keyboard_protocol;
usb_send_in();
return;
}
return;
}
if (bRequest == HID_SET_IDLE) {
- usb_keyboard_idle_config = (wValue >> 8);
+ keyboard_idle = (wValue >> 8);
usb_keyboard_idle_count = 0;
//usb_wait_in_ready();
usb_send_in();
return;
}
if (bRequest == HID_SET_PROTOCOL) {
- usb_keyboard_protocol = wValue;
+ keyboard_protocol = wValue;
+#ifdef NKRO_ENABLE
+ keyboard_nkro = !!keyboard_protocol;
+#endif
+ clear_keyboard();
//usb_wait_in_ready();
usb_send_in();
return;
// protocol setting from the host. We use exactly the same report
// either way, so this variable only stores the setting since we
// are required to be able to report which setting is in use.
-uint8_t usb_keyboard_protocol=1;
+uint8_t keyboard_protocol=1;
// the idle configuration, how often we send the report to the
// host (ms * 4) even when it hasn't changed
// Windows and Linux set 0 while OS X sets 6(24ms) by SET_IDLE request.
-uint8_t usb_keyboard_idle_config=125;
+uint8_t keyobard_idle=125;
// count until idle timeout
uint8_t usb_keyboard_idle_count=0;
else
#endif
{
- if (usb_keyboard_protocol)
- result = send_report(report, KBD_ENDPOINT, 0, KBD_SIZE);
- else
- result = send_report(report, KBD_ENDPOINT, 0, 6);
+ result = send_report(report, KBD_ENDPOINT, 0, KBD_SIZE);
}
if (result) return result;
#include "host.h"
-extern uint8_t usb_keyboard_protocol;
-extern uint8_t usb_keyboard_idle_config;
extern uint8_t usb_keyboard_idle_count;
extern volatile uint8_t usb_keyboard_leds;
mouse_report.x = ps2_host_recv_response();
mouse_report.y = ps2_host_recv_response();
} else {
- if (!debug_mouse) print("ps2_mouse: fail to get mouse packet\n");
+ if (debug_mouse) print("ps2_mouse: fail to get mouse packet\n");
return;
}
+ xprintf("%ud ", timer_read());
+ print("ps2_mouse raw: [");
+ phex(mouse_report.buttons); print("|");
+ print_hex8((uint8_t)mouse_report.x); print(" ");
+ print_hex8((uint8_t)mouse_report.y); print("]\n");
/* if mouse moves or buttons state changes */
if (mouse_report.x || mouse_report.y ||
projects / tmk_firmware.git / commitdiff