Add power control of key switch board

[tmk_firmware.git] / keyboard / hhkb_rn42 / config.h

diff --git a/keyboard/hhkb_rn42/config.h b/keyboard/hhkb_rn42/config.h
index a0ab878eb80fc3db06073f4b6682f47bc0f11c12..21e73f1c5319fe76fc299564cb6d36925a824265 100644 (file)
--- a/keyboard/hhkb_rn42/config.h
+++ b/keyboard/hhkb_rn42/config.h
@@ -20,7 +20,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 
 #define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0xCAFE
+#define PRODUCT_ID      0x4242
 #define DEVICE_VER      0x0104
 #define MANUFACTURER    t.m.k.
 #define PRODUCT         HHKB mod
@@ -28,7 +28,11 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 
 /* matrix size */
-#define MATRIX_ROWS 8
+#ifdef HHKB_JP
+#   define MATRIX_ROWS 16
+#else
+#   define MATRIX_ROWS 8
+#endif
 #define MATRIX_COLS 8
 
 
@@ -46,6 +50,8 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* Boot Magic salt key: Space */
 #define BOOTMAGIC_KEY_SALT      KC_FN6
 
+/* power control of key switch board */
+#define HHKB_POWER_SAVING
 
 /*
  * Hardware Serial(UART)
@@ -57,25 +63,35 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
     #define RTSEN 0
     #define CTSEN 1
 
-    #define SERIAL_UART_BAUD       115200
-    #define SERIAL_UART_DATA       UDR1
-    #define SERIAL_UART_UBRR       ((F_CPU/(16.0*SERIAL_UART_BAUD)-1+0.5))
-    #define SERIAL_UART_RXD_VECT   USART1_RX_vect
-    #define SERIAL_UART_TXD_READY  (UCSR1A&(1<<UDRE1))
-    #define SERIAL_UART_INIT()     do { \
+    #define SERIAL_UART_BAUD        115200
+    #define SERIAL_UART_DATA        UDR1
+    #define SERIAL_UART_UBRR        ((F_CPU/(16.0*SERIAL_UART_BAUD)-1+0.5))
+    #define SERIAL_UART_RXD_VECT    USART1_RX_vect
+    #define SERIAL_UART_TXD_READY   (UCSR1A&(1<<UDRE1))
+    #define SERIAL_UART_INIT()      do { \
         UBRR1L = (uint8_t) SERIAL_UART_UBRR;       /* baud rate */ \
         UBRR1H = ((uint16_t)SERIAL_UART_UBRR>>8);  /* baud rate */ \
         UCSR1B |= (1<<RXCIE1) | (1<<RXEN1); /* RX interrupt, RX: enable */ \
         UCSR1B |= (0<<TXCIE1) | (1<<TXEN1); /* TX interrupt, TX: enable */ \
         UCSR1C |= (0<<UPM11) | (0<<UPM10);  /* parity: none(00), even(01), odd(11) */ \
-        UCSR1D |= (0<<RTSEN) | (0<<CTSEN);  /* RTS, CTS */ \
+        UCSR1D |= (0<<RTSEN) | (0<<CTSEN);  /* RTS, CTS(no flow control by hardware) */ \
+        DDRD |= (1<<5); PORTD &= ~(1<<5);   /* RTS for flow control by firmware */ \
         sei(); \
     } while(0)
+    #define SERIAL_UART_RTS_LO()    do { PORTD &= ~(1<<5); } while (0)
+    #define SERIAL_UART_RTS_HI()    do { PORTD |=  (1<<5); } while (0)
 #else
     #error "USART configuration is needed."
 #endif
 
 
+/* for debug */
+#define SUART_OUT_PORT  PORTD
+#define SUART_OUT_BIT   0
+#define SUART_IN_PIN    PIND
+#define SUART_IN_BIT    1
+
+
 /*
  * Feature disable options
  *  These options are also useful to firmware size reduction.