Revert ps2_usb/Makefile and config.h

[tmk_firmware.git] / converter / ps2_usb / Makefile

diff --git a/converter/ps2_usb/Makefile b/converter/ps2_usb/Makefile
index 1278a74be700e56eb416f04f6be62f6749cf2891..1dd23c157e1f32ee652b1d2f9e357d7071a45a06 100644 (file)
--- a/converter/ps2_usb/Makefile
+++ b/converter/ps2_usb/Makefile
@@ -1,10 +1,8 @@
+# 
+# Makefile for Teensy
 #
-# Makefile for PJRC Teensy
-#
-
-
 # Target file name (without extension).
-TARGET = ps2_usb_pjrc
+TARGET = ps2_usb_lufa
 
 # Directory common source filess exist
 TOP_DIR = ../..
@@ -12,50 +10,96 @@ TOP_DIR = ../..
 # Directory keyboard dependent files exist
 TARGET_DIR = .
 
-# keyboard dependent files
-SRC =  keymap.c \
+# project specific files
+SRC =  keymap_common.c \
        matrix.c \
-       led.c \
-       ps2.c
+       led.c
 
-CONFIG_H = config_pjrc.h
+ifdef KEYMAP
+    SRC := keymap_$(KEYMAP).c $(SRC)
+else
+    SRC := keymap_plain.c $(SRC)
+endif
 
+CONFIG_H = config.h
 
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
 
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
 
 # Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
 F_CPU = 16000000
 
 
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+
 # Build Options
-#   *Comment out* to disable the options.
+#   comment out to disable the options.
 #
-MOUSEKEY_ENABLE = yes  # Mouse keys
-EXTRAKEY_ENABLE = yes  # Audio control and System control
-NKRO_ENABLE = yes      # USB Nkey Rollover
+#BOOTMAGIC_ENABLE = yes        # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes  # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes  # Audio control and System control(+450)
+CONSOLE_ENABLE = yes   # Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+NKRO_ENABLE = yes      # USB Nkey Rollover - not yet supported in LUFA
 
 
+# PS/2 Options
+#
+PS2_USE_USART = yes    # uses hardware USART engine for PS/2 signal receive(recomened)
+#PS2_USE_INT = yes     # uses external interrupt for falling edge of PS/2 clock pin
+#PS2_USE_BUSYWAIT = yes        # uses primitive reference code
 
-#---------------- Programming Options --------------------------
-PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
 
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
 
 # Search Path
 VPATH += $(TARGET_DIR)
 VPATH += $(TOP_DIR)
 
-
-include $(TOP_DIR)/protocol/pjrc.mk
 include $(TOP_DIR)/protocol.mk
+include $(TOP_DIR)/protocol/lufa.mk
 include $(TOP_DIR)/common.mk
 include $(TOP_DIR)/rules.mk