refactor, non-working

diff --git a/drivers/avr/i2c_master.c b/drivers/avr/i2c_master.c
index caca2179e0e555a6d93123f5c1e526632411c3f8..30ea760c9ff00bc7e4fb9e8c9837f555d9b2180c 100755 (executable)
--- a/drivers/avr/i2c_master.c
+++ b/drivers/avr/i2c_master.c
@@ -19,7 +19,7 @@ void i2c_init(void)
   //TWBR = 10;
 }
 
-i2c_status_t i2c_start(uint8_t address, uint8_t timeout)
+i2c_status_t i2c_start(uint8_t address, uint16_t timeout)
 {
        // reset TWI control register
        TWCR = 0;
@@ -28,13 +28,13 @@ i2c_status_t i2c_start(uint8_t address, uint8_t timeout)
 
   uint16_t timeout_timer = timer_read();
   while( !(TWCR & (1<<TWINT)) ) {
-    if (timeout && (timer_read() - timeout_timer) > timeout) {
+    if (timeout && ((timer_read() - timeout_timer) > timeout)) {
       return I2C_STATUS_TIMEOUT;
     }
   }
 
        // check if the start condition was successfully transmitted
-       if(((TW_STATUS & 0xF8) != TW_START) && ((TW_STATUS & 0xF8) != TW_REP_START)){ return 1; }
+       if(((TW_STATUS & 0xF8) != TW_START) && ((TW_STATUS & 0xF8) != TW_REP_START)){ return I2C_STATUS_ERROR; }
 
        // load slave address into data register
        TWDR = address;
@@ -43,19 +43,19 @@ i2c_status_t i2c_start(uint8_t address, uint8_t timeout)
 
   timeout_timer = timer_read();
   while( !(TWCR & (1<<TWINT)) ) {
-    if (timeout && (timer_read() - timeout_timer) > I2C_TIMEOUT) {
+    if (timeout && ((timer_read() - timeout_timer) > timeout)) {
       return I2C_STATUS_TIMEOUT;
     }
   }
 
        // check if the device has acknowledged the READ / WRITE mode
        uint8_t twst = TW_STATUS & 0xF8;
-       if ( (twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK) ) return 1;
+       if ( (twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK) ) return I2C_STATUS_ERROR;
 
-       return 0;
+       return I2C_STATUS_SUCCESS;
 }
 
-i2c_status_t i2c_write(uint8_t data, uint8_t timeout)
+i2c_status_t i2c_write(uint8_t data, uint16_t timeout)
 {
        // load data into data register
        TWDR = data;
@@ -64,17 +64,17 @@ i2c_status_t i2c_write(uint8_t data, uint8_t timeout)
 
   uint16_t timeout_timer = timer_read();
   while( !(TWCR & (1<<TWINT)) ) {
-    if (timeout && (timer_read() - timeout_timer) > I2C_TIMEOUT) {
+    if (timeout && ((timer_read() - timeout_timer) > timeout)) {
       return I2C_STATUS_TIMEOUT;
     }
   }
 
-       if( (TW_STATUS & 0xF8) != TW_MT_DATA_ACK ){ return 1; }
+       if( (TW_STATUS & 0xF8) != TW_MT_DATA_ACK ){ return I2C_STATUS_ERROR; }
 
-       return 0;
+       return I2C_STATUS_SUCCESS;
 }
 
-i2c_status_t i2c_read_ack(uint8_t timeout)
+int16_t i2c_read_ack(uint16_t timeout)
 {
 
        // start TWI module and acknowledge data after reception
@@ -82,7 +82,7 @@ i2c_status_t i2c_read_ack(uint8_t timeout)
 
   uint16_t timeout_timer = timer_read();
   while( !(TWCR & (1<<TWINT)) ) {
-    if (timeout && (timer_read() - timeout_timer) > I2C_TIMEOUT) {
+    if (timeout && ((timer_read() - timeout_timer) > timeout)) {
       return I2C_STATUS_TIMEOUT;
     }
   }
@@ -91,7 +91,7 @@ i2c_status_t i2c_read_ack(uint8_t timeout)
        return TWDR;
 }
 
-i2c_status_t i2c_read_nack(uint8_t timeout)
+int16_t i2c_read_nack(uint16_t timeout)
 {
 
        // start receiving without acknowledging reception
@@ -99,7 +99,7 @@ i2c_status_t i2c_read_nack(uint8_t timeout)
 
   uint16_t timeout_timer = timer_read();
   while( !(TWCR & (1<<TWINT)) ) {
-    if (timeout && (timer_read() - timeout_timer) > I2C_TIMEOUT) {
+    if (timeout && ((timer_read() - timeout_timer) > timeout)) {
       return I2C_STATUS_TIMEOUT;
     }
   }
@@ -108,81 +108,112 @@ i2c_status_t i2c_read_nack(uint8_t timeout)
        return TWDR;
 }
 
-i2c_status_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length)
+i2c_status_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout)
 {
-       if (i2c_start(address | I2C_WRITE)) return 1;
+  i2c_status_t status = i2c_start(address | I2C_WRITE, timeout);
+       if (status) return status;
 
-       for (uint16_t i = 0; i < length; i++)
-       {
-               if (i2c_write(data[i])) return 1;
+       for (uint16_t i = 0; i < length; i++) {
+               status = i2c_write(data[i], timeout);
+    if (status) return status;
        }
 
-       i2c_stop();
+       status = i2c_stop(timeout);
+  if (status) return status;
 
-       return 0;
+       return I2C_STATUS_SUCCESS;
 }
 
-uint8_t i2c_receive(uint8_t address, uint8_t* data, uint16_t length)
+i2c_status_t i2c_receive(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout)
 {
-       if (i2c_start(address | I2C_READ)) return 1;
-
-       for (uint16_t i = 0; i < (length-1); i++)
-       {
-               data[i] = i2c_read_ack();
+  i2c_status_t status = i2c_start(address | I2C_READ, timeout);
+       if (status) return status;
+
+       for (uint16_t i = 0; i < (length-1); i++) {
+    status = i2c_read_ack(timeout);
+    if (status >= 0) {
+      data[i] = status;
+    } else {
+      return status;
+    }
        }
-       data[(length-1)] = i2c_read_nack();
 
-       i2c_stop();
+  status = i2c_read_nack(timeout);
+  if (status >= 0 ) {
+    data[(length-1)] = status;
+  } else {
+    return status;
+  }
+
+  status = i2c_stop(timeout);
+  if (status) return status;
 
-       return 0;
+       return I2C_STATUS_SUCCESS;
 }
 
-uint8_t i2c_writeReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length)
+i2c_status_t i2c_writeReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout)
 {
-       if (i2c_start(devaddr | 0x00)) return 1;
+  i2c_status_t status = i2c_start(devaddr | 0x00, timeout);
+       if (status) return status;
 
-       i2c_write(regaddr);
+       status = i2c_write(regaddr, timeout);
+  if (status) return status;
 
-       for (uint16_t i = 0; i < length; i++)
-       {
-               if (i2c_write(data[i])) return 1;
+       for (uint16_t i = 0; i < length; i++) {
+    status = i2c_write(data[i], timeout);
+               if (status) return status;
        }
 
-       i2c_stop();
+       status = i2c_stop(timeout);
+  if (status) return status;
 
-       return 0;
+       return I2C_STATUS_SUCCESS;
 }
 
-uint8_t i2c_readReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length)
+i2c_status_t i2c_readReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout)
 {
-       if (i2c_start(devaddr)) return 1;
+  i2c_status_t status = i2c_start(devaddr, timeout);
+       if (status) return status;
 
-       i2c_write(regaddr);
+  status = i2c_write(regaddr, timeout);
+  if (status) return status;
 
-       if (i2c_start(devaddr | 0x01)) return 1;
+  status = i2c_start(devaddr | 0x01, timeout);
+       if (status) return status;
 
-       for (uint16_t i = 0; i < (length-1); i++)
-       {
-               data[i] = i2c_read_ack();
+       for (uint16_t i = 0; i < (length-1); i++) {
+               status = i2c_read_ack(timeout);
+    if (status >= 0) {
+      data[i] = status;
+    } else {
+      return status;
+    }
        }
-       data[(length-1)] = i2c_read_nack();
 
-       i2c_stop();
+  status = i2c_read_nack(timeout);
+  if (status >= 0 ) {
+    data[(length-1)] = status;
+  } else {
+    return status;
+  }
+
+  status = i2c_stop(timeout);
+  if (status) return status;
 
-       return 0;
+       return I2C_STATUS_SUCCESS;
 }
 
-i2c_status_t i2c_stop(uint8_t timeout)
+i2c_status_t i2c_stop(uint16_t timeout)
 {
        // transmit STOP condition
        TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
 
   uint16_t timeout_timer = timer_read();
   while(TWCR & (1<<TWSTO)) {
-      if (timeout && (timer_read() - timeout_timer) > I2C_TIMEOUT) {
+    if (timeout && ((timer_read() - timeout_timer) > timeout)) {
       return I2C_STATUS_TIMEOUT;
     }
   }
 
-  return 0;
+  return I2C_STATUS_SUCCESS;
 }

diff --git a/drivers/avr/i2c_master.h b/drivers/avr/i2c_master.h
index 3c7731e8dc4d5b7bd15d00b373c619d6147d49b0..0806d76aa9469a2320ff9afc0a165e50b04eb0be 100755 (executable)
--- a/drivers/avr/i2c_master.h
+++ b/drivers/avr/i2c_master.h
@@ -8,20 +8,21 @@
 #define I2C_READ 0x01
 #define I2C_WRITE 0x00
 
-typedef i2c_status_t int16_t
-#define I2C_STATUS_TIMEOUT (-1)
+typedef int16_t i2c_status_t;
 
-#define I2C_NO_TIMEOUT 0
+#define I2C_STATUS_SUCCESS (0)
+#define I2C_STATUS_ERROR   (-1)
+#define I2C_STATUS_TIMEOUT (-2)
 
 void i2c_init(void);
-i2c_status_t i2c_start(uint8_t address, uint8_t timeout);
-i2c_status_t i2c_write(uint8_t data, uint8_t timeout);
-i2c_status_t i2c_read_ack(uint8_t timeout);
-i2c_status_t i2c_read_nack(uint8_t timeout);
-uint8_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length);
-uint8_t i2c_receive(uint8_t address, uint8_t* data, uint16_t length);
-uint8_t i2c_writeReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length);
-uint8_t i2c_readReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length);
-i2c_status_t i2c_stop(uint8_t timeout);
+i2c_status_t i2c_start(uint8_t address, uint16_t timeout);
+i2c_status_t i2c_write(uint8_t data, uint16_t timeout);
+int16_t i2c_read_ack(uint16_t timeout);
+int16_t i2c_read_nack(uint16_t timeout);
+i2c_status_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout);
+i2c_status_t i2c_receive(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout);
+i2c_status_t i2c_writeReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout);
+i2c_status_t i2c_readReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout);
+i2c_status_t i2c_stop(uint16_t timeout);
 
 #endif // I2C_MASTER_H

diff --git a/drivers/avr/is31fl3731.c b/drivers/avr/is31fl3731.c
index 158b77b7b1eed4d24a620e77b8826256a7a186d5..70813464b2be3988258d120099b0b4c967a6e710 100644 (file)
--- a/drivers/avr/is31fl3731.c
+++ b/drivers/avr/is31fl3731.c
@@ -49,6 +49,14 @@
 #define ISSI_COMMANDREGISTER 0xFD
 #define ISSI_BANK_FUNCTIONREG 0x0B    // helpfully called 'page nine'
 
+#ifndef ISSI_TIMEOUT
+  #define ISSI_TIMEOUT 100
+#endif
+
+#ifndef ISSI_PERSISTENCE
+  #define ISSI_PERSISTENCE 0
+#endif
+
 // Transfer buffer for TWITransmitData()
 uint8_t g_twi_transfer_buffer[20];
 
@@ -78,100 +86,104 @@ bool g_led_control_registers_update_required = false;
 // 0x10 - R16,R15,R14,R13,R12,R11,R10,R09
 
 
-uint8_t IS31FL3731_write_register( uint8_t addr, uint8_t reg, uint8_t data )
+void IS31FL3731_write_register( uint8_t addr, uint8_t reg, uint8_t data )
 {
        g_twi_transfer_buffer[0] = reg;
        g_twi_transfer_buffer[1] = data;
 
-       //Transmit data until succesful
-  //while(i2c_transmit(addr << 1, g_twi_transfer_buffer,2) != 0);
-  return i2c_transmit(addr << 1, g_twi_transfer_buffer,2);
+  #if ISSI_PERSISTENCE > 0
+    for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
+      if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT) == 0)
+        break;
+    }
+  #else
+    i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT);
+  #endif
 }
 
-uint8_t IS31FL3731_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer )
+void IS31FL3731_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer )
 {
-  uint8_t ret = 0;
        // assumes bank is already selected
 
        // transmit PWM registers in 9 transfers of 16 bytes
        // g_twi_transfer_buffer[] is 20 bytes
 
        // iterate over the pwm_buffer contents at 16 byte intervals
-       for ( int i = 0; i < 144; i += 16 )
-       {
+       for ( int i = 0; i < 144; i += 16 ) {
                // set the first register, e.g. 0x24, 0x34, 0x44, etc.
                g_twi_transfer_buffer[0] = 0x24 + i;
                // copy the data from i to i+15
                // device will auto-increment register for data after the first byte
                // thus this sets registers 0x24-0x33, 0x34-0x43, etc. in one transfer
-               for ( int j = 0; j < 16; j++ )
-               {
+               for ( int j = 0; j < 16; j++ ) {
                        g_twi_transfer_buffer[1 + j] = pwm_buffer[i + j];
                }
 
-               //Transmit buffer until succesful
-               //while(i2c_transmit(addr << 1, g_twi_transfer_buffer,17) != 0);
-    ret |= i2c_transmit(addr << 1, g_twi_transfer_buffer, 17);
+    #if ISSI_PERSISTENCE > 0
+      for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
+        if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT) == 0)
+          break;
+      }
+    #else
+      i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT);
+    #endif
        }
-  return ret;
 }
 
-uint8_t IS31FL3731_init( uint8_t addr )
+void IS31FL3731_init( uint8_t addr )
 {
-  uint8_t ret = 0;
        // In order to avoid the LEDs being driven with garbage data
        // in the LED driver's PWM registers, first enable software shutdown,
        // then set up the mode and other settings, clear the PWM registers,
        // then disable software shutdown.
 
        // select "function register" bank
-       ret |= IS31FL3731_write_register( addr, ISSI_COMMANDREGISTER, ISSI_BANK_FUNCTIONREG );
+       IS31FL3731_write_register( addr, ISSI_COMMANDREGISTER, ISSI_BANK_FUNCTIONREG );
 
        // enable software shutdown
-       ret |= IS31FL3731_write_register( addr, ISSI_REG_SHUTDOWN, 0x00 );
+       IS31FL3731_write_register( addr, ISSI_REG_SHUTDOWN, 0x00 );
        // this delay was copied from other drivers, might not be needed
        _delay_ms( 10 );
 
        // picture mode
-       ret |= IS31FL3731_write_register( addr, ISSI_REG_CONFIG, ISSI_REG_CONFIG_PICTUREMODE );
+       IS31FL3731_write_register( addr, ISSI_REG_CONFIG, ISSI_REG_CONFIG_PICTUREMODE );
        // display frame 0
-       ret |= IS31FL3731_write_register( addr, ISSI_REG_PICTUREFRAME, 0x00 );
+       IS31FL3731_write_register( addr, ISSI_REG_PICTUREFRAME, 0x00 );
        // audio sync off
-       ret |= IS31FL3731_write_register( addr, ISSI_REG_AUDIOSYNC, 0x00 );
+       IS31FL3731_write_register( addr, ISSI_REG_AUDIOSYNC, 0x00 );
 
        // select bank 0
-       ret |= IS31FL3731_write_register( addr, ISSI_COMMANDREGISTER, 0 );
+       IS31FL3731_write_register( addr, ISSI_COMMANDREGISTER, 0 );
 
        // turn off all LEDs in the LED control register
        for ( int i = 0x00; i <= 0x11; i++ )
        {
-               ret |= IS31FL3731_write_register( addr, i, 0x00 );
+               IS31FL3731_write_register( addr, i, 0x00 );
        }
 
        // turn off all LEDs in the blink control register (not really needed)
        for ( int i = 0x12; i <= 0x23; i++ )
        {
-               ret |= IS31FL3731_write_register( addr, i, 0x00 );
+               IS31FL3731_write_register( addr, i, 0x00 );
        }
 
        // set PWM on all LEDs to 0
        for ( int i = 0x24; i <= 0xB3; i++ )
        {
-               ret |= IS31FL3731_write_register( addr, i, 0x00 );
+               IS31FL3731_write_register( addr, i, 0x00 );
        }
 
        // select "function register" bank
-       ret |= IS31FL3731_write_register( addr, ISSI_COMMANDREGISTER, ISSI_BANK_FUNCTIONREG );
+       IS31FL3731_write_register( addr, ISSI_COMMANDREGISTER, ISSI_BANK_FUNCTIONREG );
 
        // disable software shutdown
-       ret |= IS31FL3731_write_register( addr, ISSI_REG_SHUTDOWN, 0x01 );
+       IS31FL3731_write_register( addr, ISSI_REG_SHUTDOWN, 0x01 );
 
        // select bank 0 and leave it selected.
        // most usage after initialization is just writing PWM buffers in bank 0
        // as there's not much point in double-buffering
-       ret |= IS31FL3731_write_register( addr, ISSI_COMMANDREGISTER, 0 );
+       IS31FL3731_write_register( addr, ISSI_COMMANDREGISTER, 0 );
 
-  return ret;
 }
 
 void IS31FL3731_set_color( int index, uint8_t red, uint8_t green, uint8_t blue )
@@ -224,32 +236,27 @@ void IS31FL3731_set_led_control_register( uint8_t index, bool red, bool green, b
 
        g_led_control_registers_update_required = true;
 
-
 }
 
-uint8_t IS31FL3731_update_pwm_buffers( uint8_t addr1, uint8_t addr2 )
+void IS31FL3731_update_pwm_buffers( uint8_t addr1, uint8_t addr2 )
 {
-  uint8_t ret = 0;
        if ( g_pwm_buffer_update_required )
        {
-               ret |= IS31FL3731_write_pwm_buffer( addr1, g_pwm_buffer[0] );
-               ret |= IS31FL3731_write_pwm_buffer( addr2, g_pwm_buffer[1] );
+               IS31FL3731_write_pwm_buffer( addr1, g_pwm_buffer[0] );
+               IS31FL3731_write_pwm_buffer( addr2, g_pwm_buffer[1] );
        }
        g_pwm_buffer_update_required = false;
-  return ret;
 }
 
-uint8_t IS31FL3731_update_led_control_registers( uint8_t addr1, uint8_t addr2 )
+void IS31FL3731_update_led_control_registers( uint8_t addr1, uint8_t addr2 )
 {
-  uint8_t ret = 0;
        if ( g_led_control_registers_update_required )
        {
                for ( int i=0; i<18; i++ )
                {
-                       ret |= IS31FL3731_write_register(addr1, i, g_led_control_registers[0][i] );
-                       ret |= IS31FL3731_write_register(addr2, i, g_led_control_registers[1][i] );
+                       IS31FL3731_write_register(addr1, i, g_led_control_registers[0][i] );
+                       IS31FL3731_write_register(addr2, i, g_led_control_registers[1][i] );
                }
        }
-  return ret;
 }
 

diff --git a/drivers/avr/is31fl3731.h b/drivers/avr/is31fl3731.h
index 62632e276a4338e45be6d3646c08afe9fe4b42c2..3d30fc67b7543ea9e2bc57f74bcd80e96ea0b42a 100644 (file)
--- a/drivers/avr/is31fl3731.h
+++ b/drivers/avr/is31fl3731.h
@@ -31,9 +31,9 @@ typedef struct is31_led {
 
 extern const is31_led g_is31_leds[DRIVER_LED_TOTAL];
 
-uint8_t IS31FL3731_init( uint8_t addr );
-uint8_t IS31FL3731_write_register( uint8_t addr, uint8_t reg, uint8_t data );
-uint8_t IS31FL3731_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer );
+void IS31FL3731_init( uint8_t addr );
+void IS31FL3731_write_register( uint8_t addr, uint8_t reg, uint8_t data );
+void IS31FL3731_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer );
 
 void IS31FL3731_set_color( int index, uint8_t red, uint8_t green, uint8_t blue );
 void IS31FL3731_set_color_all( uint8_t red, uint8_t green, uint8_t blue );
@@ -44,8 +44,8 @@ void IS31FL3731_set_led_control_register( uint8_t index, bool red, bool green, b
 // (eg. from a timer interrupt).
 // Call this while idle (in between matrix scans).
 // If the buffer is dirty, it will update the driver with the buffer.
-uint8_t IS31FL3731_update_pwm_buffers( uint8_t addr1, uint8_t addr2 );
-uint8_t IS31FL3731_update_led_control_registers( uint8_t addr1, uint8_t addr2 );
+void IS31FL3731_update_pwm_buffers( uint8_t addr1, uint8_t addr2 );
+void IS31FL3731_update_led_control_registers( uint8_t addr1, uint8_t addr2 );
 
 #define C1_1  0x24
 #define C1_2  0x25

diff --git a/keyboards/ergodox_ez/config.h b/keyboards/ergodox_ez/config.h
index ec1620030c9c18e55c0265bc4472092426824bc9..1285cbe1c9752c8cc76fda9ff173766ad909d9d8 100644 (file)
--- a/keyboards/ergodox_ez/config.h
+++ b/keyboards/ergodox_ez/config.h
@@ -138,6 +138,4 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 //#define NO_ACTION_FUNCTION
 //#define DEBUG_MATRIX_SCAN_RATE
 
-#define I2C_TIMEOUT 1000
-
 #endif

diff --git a/keyboards/ergodox_ez/ergodox_ez.c b/keyboards/ergodox_ez/ergodox_ez.c
index 3a2d1273fabe0ce0cff028286a88fd71faaff0c5..65671b38fe3fd2367e82d6549db50a6d7a2f0408 100644 (file)
--- a/keyboards/ergodox_ez/ergodox_ez.c
+++ b/keyboards/ergodox_ez/ergodox_ez.c
@@ -24,7 +24,7 @@ extern inline void ergodox_led_all_set(uint8_t n);
 
 
 bool i2c_initialized = 0;
-uint8_t mcp23018_status = 0x20;
+i2c_status_t mcp23018_status = 0x20;
 
 void matrix_init_kb(void) {
    // keyboard LEDs (see "PWM on ports OC1(A|B|C)" in "teensy-2-0.md")
@@ -125,23 +125,23 @@ uint8_t init_mcp23018(void) {
     // - unused  : input  : 1
     // - input   : input  : 1
     // - driving : output : 0
-    mcp23018_status = i2c_start(I2C_ADDR_WRITE);    if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(IODIRA);            if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(0b00000000);        if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(0b00111111);        if (mcp23018_status) goto out;
-    i2c_stop();
+    mcp23018_status = i2c_start(I2C_ADDR_WRITE, 0);    if (mcp23018_status) goto out;
+    mcp23018_status = i2c_write(IODIRA, 0);            if (mcp23018_status) goto out;
+    mcp23018_status = i2c_write(0b00000000, 0);        if (mcp23018_status) goto out;
+    mcp23018_status = i2c_write(0b00111111, 0);        if (mcp23018_status) goto out;
+    i2c_stop(0);
 
     // set pull-up
     // - unused  : on  : 1
     // - input   : on  : 1
     // - driving : off : 0
-    mcp23018_status = i2c_start(I2C_ADDR_WRITE);    if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(GPPUA);             if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(0b00000000);        if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(0b00111111);        if (mcp23018_status) goto out;
+    mcp23018_status = i2c_start(I2C_ADDR_WRITE, 0);    if (mcp23018_status) goto out;
+    mcp23018_status = i2c_write(GPPUA, 0);             if (mcp23018_status) goto out;
+    mcp23018_status = i2c_write(0b00000000, 0);        if (mcp23018_status) goto out;
+    mcp23018_status = i2c_write(0b00111111, 0);        if (mcp23018_status) goto out;
 
 out:
-    i2c_stop();
+    i2c_stop(0);
 
 #ifdef LEFT_LEDS
     if (!mcp23018_status) mcp23018_status = ergodox_left_leds_update();
@@ -165,22 +165,22 @@ uint8_t ergodox_left_leds_update(void) {
     // - unused  : hi-Z : 1
     // - input   : hi-Z : 1
     // - driving : hi-Z : 1
-    mcp23018_status = i2c_start(I2C_ADDR_WRITE);
+    mcp23018_status = i2c_start(I2C_ADDR_WRITE, 0);
     if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(OLATA);
+    mcp23018_status = i2c_write(OLATA, 0);
     if (mcp23018_status) goto out;
     mcp23018_status = i2c_write(0b11111111
-                                & ~(ergodox_left_led_3<<LEFT_LED_3_SHIFT)
-                                );
+                                & ~(ergodox_left_led_3<<LEFT_LED_3_SHIFT),
+                                0);
     if (mcp23018_status) goto out;
     mcp23018_status = i2c_write(0b11111111
                                 & ~(ergodox_left_led_2<<LEFT_LED_2_SHIFT)
-                                & ~(ergodox_left_led_1<<LEFT_LED_1_SHIFT)
-                                );
+                                & ~(ergodox_left_led_1<<LEFT_LED_1_SHIFT),
+                                0);
     if (mcp23018_status) goto out;
 
  out:
-    i2c_stop();
+    i2c_stop(0);
     return mcp23018_status;
 }
 #endif

diff --git a/keyboards/ergodox_ez/ergodox_ez.h b/keyboards/ergodox_ez/ergodox_ez.h
index 3ffc32553c0acd2f6cf6fb922d08e17ebd422375..9086db2fbd0d5d76ff188498e25bac75ed7756fb 100644 (file)
--- a/keyboards/ergodox_ez/ergodox_ez.h
+++ b/keyboards/ergodox_ez/ergodox_ez.h
@@ -23,7 +23,7 @@
 #define OLATA           0x14            // output latch register
 #define OLATB           0x15
 
-extern uint8_t mcp23018_status;
+extern i2c_status_t mcp23018_status;
 
 void init_ergodox(void);
 void ergodox_blink_all_leds(void);

diff --git a/keyboards/ergodox_ez/matrix.c b/keyboards/ergodox_ez/matrix.c
index 8b117166fb366b9d835f426f1b466a3cbca494bf..d8b708a163ff12f1534bbdc36065449f5c70fdea 100644 (file)
--- a/keyboards/ergodox_ez/matrix.c
+++ b/keyboards/ergodox_ez/matrix.c
@@ -295,13 +295,13 @@ static matrix_row_t read_cols(uint8_t row)
             return 0;
         } else {
             uint8_t data = 0;
-            mcp23018_status = i2c_start(I2C_ADDR_WRITE);    if (mcp23018_status) goto out;
-            mcp23018_status = i2c_write(GPIOB);             if (mcp23018_status) goto out;
-            mcp23018_status = i2c_start(I2C_ADDR_READ);     if (mcp23018_status) goto out;
-            data = i2c_read_nack();
-            data = ~data;
+            mcp23018_status = i2c_start(I2C_ADDR_WRITE, 0);    if (mcp23018_status) goto out;
+            mcp23018_status = i2c_write(GPIOB, 0);             if (mcp23018_status) goto out;
+            mcp23018_status = i2c_start(I2C_ADDR_READ, 0);     if (mcp23018_status) goto out;
+            mcp23018_status = i2c_read_nack(0);                if (mcp23018_status < 0) goto out;
+            data = ~((uint8_t)mcp23018_status);
         out:
-            i2c_stop();
+            i2c_stop(0);
             return data;
         }
     } else {
@@ -350,11 +350,11 @@ static void select_row(uint8_t row)
         } else {
             // set active row low  : 0
             // set other rows hi-Z : 1
-            mcp23018_status = i2c_start(I2C_ADDR_WRITE);        if (mcp23018_status) goto out;
-            mcp23018_status = i2c_write(GPIOA);                 if (mcp23018_status) goto out;
-            mcp23018_status = i2c_write(0xFF & ~(1<<row));      if (mcp23018_status) goto out;
+            mcp23018_status = i2c_start(I2C_ADDR_WRITE, 0);        if (mcp23018_status) goto out;
+            mcp23018_status = i2c_write(GPIOA, 0);                 if (mcp23018_status) goto out;
+            mcp23018_status = i2c_write(0xFF & ~(1<<row), 0);      if (mcp23018_status) goto out;
         out:
-            i2c_stop();
+            i2c_stop(0);
         }
     } else {
         // select on teensy

diff --git a/quantum/rgb_matrix.c b/quantum/rgb_matrix.c
index d71283f7c24c29bfc95034ea6a5d41fc5bd2f225..874573bb2496916327c123efbc21843488cc6813 100644 (file)
--- a/quantum/rgb_matrix.c
+++ b/quantum/rgb_matrix.c
@@ -102,13 +102,8 @@ void map_row_column_to_led( uint8_t row, uint8_t column, uint8_t *led_i, uint8_t
 }
 
 void rgb_matrix_update_pwm_buffers(void) {
-    uint8_t ret = IS31FL3731_update_pwm_buffers( DRIVER_ADDR_1, DRIVER_ADDR_2 );
-    ret |= IS31FL3731_update_led_control_registers( DRIVER_ADDR_1, DRIVER_ADDR_2 );
-    if (ret == 2) {
-      wait_ms(1000);
-      i2c_stop();
-      rgb_matrix_setup_drivers();
-    }
+    IS31FL3731_update_pwm_buffers( DRIVER_ADDR_1, DRIVER_ADDR_2 );
+    IS31FL3731_update_led_control_registers( DRIVER_ADDR_1, DRIVER_ADDR_2 );
 }
 
 void rgb_matrix_set_color( int index, uint8_t red, uint8_t green, uint8_t blue ) {