--- /dev/null
+/*
+ ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+/**
+ * @file templates/chconf.h
+ * @brief Configuration file template.
+ * @details A copy of this file must be placed in each project directory, it
+ * contains the application specific kernel settings.
+ *
+ * @addtogroup config
+ * @details Kernel related settings and hooks.
+ * @{
+ */
+
+#ifndef CHCONF_H
+#define CHCONF_H
+
+#define _CHIBIOS_RT_CONF_
+
+/*===========================================================================*/
+/**
+ * @name System timers settings
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief System time counter resolution.
+ * @note Allowed values are 16 or 32 bits.
+ */
+#define CH_CFG_ST_RESOLUTION 32
+
+/**
+ * @brief System tick frequency.
+ * @details Frequency of the system timer that drives the system ticks. This
+ * setting also defines the system tick time unit.
+ */
+#define CH_CFG_ST_FREQUENCY 100000
+
+/**
+ * @brief Time delta constant for the tick-less mode.
+ * @note If this value is zero then the system uses the classic
+ * periodic tick. This value represents the minimum number
+ * of ticks that is safe to specify in a timeout directive.
+ * The value one is not valid, timeouts are rounded up to
+ * this value.
+ */
+#define CH_CFG_ST_TIMEDELTA 2
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Kernel parameters and options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Round robin interval.
+ * @details This constant is the number of system ticks allowed for the
+ * threads before preemption occurs. Setting this value to zero
+ * disables the preemption for threads with equal priority and the
+ * round robin becomes cooperative. Note that higher priority
+ * threads can still preempt, the kernel is always preemptive.
+ * @note Disabling the round robin preemption makes the kernel more compact
+ * and generally faster.
+ * @note The round robin preemption is not supported in tickless mode and
+ * must be set to zero in that case.
+ */
+#define CH_CFG_TIME_QUANTUM 0
+
+/**
+ * @brief Managed RAM size.
+ * @details Size of the RAM area to be managed by the OS. If set to zero
+ * then the whole available RAM is used. The core memory is made
+ * available to the heap allocator and/or can be used directly through
+ * the simplified core memory allocator.
+ *
+ * @note In order to let the OS manage the whole RAM the linker script must
+ * provide the @p __heap_base__ and @p __heap_end__ symbols.
+ * @note Requires @p CH_CFG_USE_MEMCORE.
+ */
+#define CH_CFG_MEMCORE_SIZE 0
+
+/**
+ * @brief Idle thread automatic spawn suppression.
+ * @details When this option is activated the function @p chSysInit()
+ * does not spawn the idle thread. The application @p main()
+ * function becomes the idle thread and must implement an
+ * infinite loop.
+ */
+#define CH_CFG_NO_IDLE_THREAD FALSE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Performance options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief OS optimization.
+ * @details If enabled then time efficient rather than space efficient code
+ * is used when two possible implementations exist.
+ *
+ * @note This is not related to the compiler optimization options.
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_OPTIMIZE_SPEED TRUE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Subsystem options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Time Measurement APIs.
+ * @details If enabled then the time measurement APIs are included in
+ * the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_TM TRUE
+
+/**
+ * @brief Threads registry APIs.
+ * @details If enabled then the registry APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_REGISTRY TRUE
+
+/**
+ * @brief Threads synchronization APIs.
+ * @details If enabled then the @p chThdWait() function is included in
+ * the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_WAITEXIT TRUE
+
+/**
+ * @brief Semaphores APIs.
+ * @details If enabled then the Semaphores APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_SEMAPHORES TRUE
+
+/**
+ * @brief Semaphores queuing mode.
+ * @details If enabled then the threads are enqueued on semaphores by
+ * priority rather than in FIFO order.
+ *
+ * @note The default is @p FALSE. Enable this if you have special
+ * requirements.
+ * @note Requires @p CH_CFG_USE_SEMAPHORES.
+ */
+#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE
+
+/**
+ * @brief Mutexes APIs.
+ * @details If enabled then the mutexes APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_MUTEXES TRUE
+
+/**
+ * @brief Enables recursive behavior on mutexes.
+ * @note Recursive mutexes are heavier and have an increased
+ * memory footprint.
+ *
+ * @note The default is @p FALSE.
+ * @note Requires @p CH_CFG_USE_MUTEXES.
+ */
+#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE
+
+/**
+ * @brief Conditional Variables APIs.
+ * @details If enabled then the conditional variables APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_MUTEXES.
+ */
+#define CH_CFG_USE_CONDVARS TRUE
+
+/**
+ * @brief Conditional Variables APIs with timeout.
+ * @details If enabled then the conditional variables APIs with timeout
+ * specification are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_CONDVARS.
+ */
+#define CH_CFG_USE_CONDVARS_TIMEOUT TRUE
+
+/**
+ * @brief Events Flags APIs.
+ * @details If enabled then the event flags APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_EVENTS TRUE
+
+/**
+ * @brief Events Flags APIs with timeout.
+ * @details If enabled then the events APIs with timeout specification
+ * are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_EVENTS.
+ */
+#define CH_CFG_USE_EVENTS_TIMEOUT TRUE
+
+/**
+ * @brief Synchronous Messages APIs.
+ * @details If enabled then the synchronous messages APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_MESSAGES TRUE
+
+/**
+ * @brief Synchronous Messages queuing mode.
+ * @details If enabled then messages are served by priority rather than in
+ * FIFO order.
+ *
+ * @note The default is @p FALSE. Enable this if you have special
+ * requirements.
+ * @note Requires @p CH_CFG_USE_MESSAGES.
+ */
+#define CH_CFG_USE_MESSAGES_PRIORITY TRUE
+
+/**
+ * @brief Mailboxes APIs.
+ * @details If enabled then the asynchronous messages (mailboxes) APIs are
+ * included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_SEMAPHORES.
+ */
+#define CH_CFG_USE_MAILBOXES TRUE
+
+/**
+ * @brief Core Memory Manager APIs.
+ * @details If enabled then the core memory manager APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_MEMCORE TRUE
+
+/**
+ * @brief Heap Allocator APIs.
+ * @details If enabled then the memory heap allocator APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or
+ * @p CH_CFG_USE_SEMAPHORES.
+ * @note Mutexes are recommended.
+ */
+#define CH_CFG_USE_HEAP TRUE
+
+/**
+ * @brief Memory Pools Allocator APIs.
+ * @details If enabled then the memory pools allocator APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_MEMPOOLS TRUE
+
+/**
+ * @brief Dynamic Threads APIs.
+ * @details If enabled then the dynamic threads creation APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_WAITEXIT.
+ * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS.
+ */
+#define CH_CFG_USE_DYNAMIC TRUE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Debug options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Debug option, kernel statistics.
+ *
+ * @note The default is @p FALSE.
+ */
+#define CH_DBG_STATISTICS FALSE
+
+/**
+ * @brief Debug option, system state check.
+ * @details If enabled the correct call protocol for system APIs is checked
+ * at runtime.
+ *
+ * @note The default is @p FALSE.
+ */
+#define CH_DBG_SYSTEM_STATE_CHECK FALSE
+
+/**
+ * @brief Debug option, parameters checks.
+ * @details If enabled then the checks on the API functions input
+ * parameters are activated.
+ *
+ * @note The default is @p FALSE.
+ */
+#define CH_DBG_ENABLE_CHECKS FALSE
+
+/**
+ * @brief Debug option, consistency checks.
+ * @details If enabled then all the assertions in the kernel code are
+ * activated. This includes consistency checks inside the kernel,
+ * runtime anomalies and port-defined checks.
+ *
+ * @note The default is @p FALSE.
+ */
+#define CH_DBG_ENABLE_ASSERTS FALSE
+
+/**
+ * @brief Debug option, trace buffer.
+ * @details If enabled then the trace buffer is activated.
+ *
+ * @note The default is @p CH_DBG_TRACE_MASK_DISABLED.
+ */
+#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED
+
+/**
+ * @brief Trace buffer entries.
+ * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is
+ * different from @p CH_DBG_TRACE_MASK_DISABLED.
+ */
+#define CH_DBG_TRACE_BUFFER_SIZE 128
+
+/**
+ * @brief Debug option, stack checks.
+ * @details If enabled then a runtime stack check is performed.
+ *
+ * @note The default is @p FALSE.
+ * @note The stack check is performed in a architecture/port dependent way.
+ * It may not be implemented or some ports.
+ * @note The default failure mode is to halt the system with the global
+ * @p panic_msg variable set to @p NULL.
+ */
+#define CH_DBG_ENABLE_STACK_CHECK TRUE
+
+/**
+ * @brief Debug option, stacks initialization.
+ * @details If enabled then the threads working area is filled with a byte
+ * value when a thread is created. This can be useful for the
+ * runtime measurement of the used stack.
+ *
+ * @note The default is @p FALSE.
+ */
+#define CH_DBG_FILL_THREADS FALSE
+
+/**
+ * @brief Debug option, threads profiling.
+ * @details If enabled then a field is added to the @p thread_t structure that
+ * counts the system ticks occurred while executing the thread.
+ *
+ * @note The default is @p FALSE.
+ * @note This debug option is not currently compatible with the
+ * tickless mode.
+ */
+#define CH_DBG_THREADS_PROFILING FALSE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Kernel hooks
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Threads descriptor structure extension.
+ * @details User fields added to the end of the @p thread_t structure.
+ */
+#define CH_CFG_THREAD_EXTRA_FIELDS \
+ /* Add threads custom fields here.*/
+
+/**
+ * @brief Threads initialization hook.
+ * @details User initialization code added to the @p chThdInit() API.
+ *
+ * @note It is invoked from within @p chThdInit() and implicitly from all
+ * the threads creation APIs.
+ */
+#define CH_CFG_THREAD_INIT_HOOK(tp) { \
+ /* Add threads initialization code here.*/ \
+}
+
+/**
+ * @brief Threads finalization hook.
+ * @details User finalization code added to the @p chThdExit() API.
+ */
+#define CH_CFG_THREAD_EXIT_HOOK(tp) { \
+ /* Add threads finalization code here.*/ \
+}
+
+/**
+ * @brief Context switch hook.
+ * @details This hook is invoked just before switching between threads.
+ */
+#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \
+ /* Context switch code here.*/ \
+}
+
+/**
+ * @brief ISR enter hook.
+ */
+#define CH_CFG_IRQ_PROLOGUE_HOOK() { \
+ /* IRQ prologue code here.*/ \
+}
+
+/**
+ * @brief ISR exit hook.
+ */
+#define CH_CFG_IRQ_EPILOGUE_HOOK() { \
+ /* IRQ epilogue code here.*/ \
+}
+
+/**
+ * @brief Idle thread enter hook.
+ * @note This hook is invoked within a critical zone, no OS functions
+ * should be invoked from here.
+ * @note This macro can be used to activate a power saving mode.
+ */
+#define CH_CFG_IDLE_ENTER_HOOK() { \
+ /* Idle-enter code here.*/ \
+}
+
+/**
+ * @brief Idle thread leave hook.
+ * @note This hook is invoked within a critical zone, no OS functions
+ * should be invoked from here.
+ * @note This macro can be used to deactivate a power saving mode.
+ */
+#define CH_CFG_IDLE_LEAVE_HOOK() { \
+ /* Idle-leave code here.*/ \
+}
+
+/**
+ * @brief Idle Loop hook.
+ * @details This hook is continuously invoked by the idle thread loop.
+ */
+#define CH_CFG_IDLE_LOOP_HOOK() { \
+ /* Idle loop code here.*/ \
+}
+
+/**
+ * @brief System tick event hook.
+ * @details This hook is invoked in the system tick handler immediately
+ * after processing the virtual timers queue.
+ */
+#define CH_CFG_SYSTEM_TICK_HOOK() { \
+ /* System tick event code here.*/ \
+}
+
+/**
+ * @brief System halt hook.
+ * @details This hook is invoked in case to a system halting error before
+ * the system is halted.
+ */
+#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \
+ /* System halt code here.*/ \
+}
+
+/**
+ * @brief Trace hook.
+ * @details This hook is invoked each time a new record is written in the
+ * trace buffer.
+ */
+#define CH_CFG_TRACE_HOOK(tep) { \
+ /* Trace code here.*/ \
+}
+
+/** @} */
+
+/*===========================================================================*/
+/* Port-specific settings (override port settings defaulted in chcore.h). */
+/*===========================================================================*/
+
+#endif /* CHCONF_H */
+
+/** @} */
--- /dev/null
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0xC1ED
+#define PRODUCT_ID 0x2390
+#define DEVICE_VER 0x0001
+#define MANUFACTURER Clueboard
+#define PRODUCT Clueboard 66% rev4
+#define DESCRIPTION QMK keyboard firmware for Clueboard
+
+/* Address for jumping to bootloader on STM32 chips. */
+/* It is chip dependent, the correct number can be looked up here:
+ * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
+ */
+#define STM32_BOOTLOADER_ADDRESS 0x1FFFD800
+
+/* key matrix size */
+#define MATRIX_ROWS 10
+#define MATRIX_COLS 8
+
+/* ROWS: Top to bottom, COLS: Left to right
+*/
+#define MATRIX_ROW_PINS { B11, A6, A3, A2, A1, B7, B6, C15, C14, C13 }
+#define MATRIX_COL_PINS { B10, B2, B1, B0, A7, B4, B3, B5 }
+#define UNUSED_PINS { B15, B14, B13, B12, B9, B8, A15, A10, A9, A8 }
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/*
+ * Feature disable options
+ * These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+ /* Backlight configuration
+ */
+#define BACKLIGHT_LEVELS 1
+
+/* Underlight configuration
+ */
+#define RGB_DI_PIN D7
+#define RGBLED_NUM 18 // Number of LEDs
+#define RGBLIGHT_HUE_STEP 32
+#define RGBLIGHT_SAT_STEP 17
+#define RGBLIGHT_VAL_STEP 17
+
+#define RGBLIGHT_ANIMATIONS
+#define RGBLIGHT_EFFECT_BREATHE_CENTER 1
+#define RGBLIGHT_EFFECT_BREATHE_MAX 200
+#define RGBLIGHT_EFFECT_CHRISTMAS_INTERVAL 666*2
+#define RGBLIGHT_EFFECT_CHRISTMAS_STEP 1
+#define RGBLIGHT_EFFECT_KNIGHT_LENGTH 3 // How many LEDs wide to light up
+#define RGBLIGHT_EFFECT_KNIGHT_OFFSET 2 // The led to start at
+#define RGBLIGHT_EFFECT_KNIGHT_LED_NUM 5 // How many LEDs to travel
+#define RGBLIGHT_EFFECT_SNAKE_LENGTH 4 // How many LEDs wide to light up
--- /dev/null
+/*
+ ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+/**
+ * @file templates/halconf.h
+ * @brief HAL configuration header.
+ * @details HAL configuration file, this file allows to enable or disable the
+ * various device drivers from your application. You may also use
+ * this file in order to override the device drivers default settings.
+ *
+ * @addtogroup HAL_CONF
+ * @{
+ */
+
+#ifndef HALCONF_H
+#define HALCONF_H
+
+#include "mcuconf.h"
+
+/**
+ * @brief Enables the PAL subsystem.
+ */
+#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__)
+#define HAL_USE_PAL TRUE
+#endif
+
+/**
+ * @brief Enables the ADC subsystem.
+ */
+#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__)
+#define HAL_USE_ADC FALSE
+#endif
+
+/**
+ * @brief Enables the CAN subsystem.
+ */
+#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__)
+#define HAL_USE_CAN FALSE
+#endif
+
+/**
+ * @brief Enables the DAC subsystem.
+ */
+#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__)
+#define HAL_USE_DAC TRUE
+#endif
+
+/**
+ * @brief Enables the EXT subsystem.
+ */
+#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__)
+#define HAL_USE_EXT FALSE
+#endif
+
+/**
+ * @brief Enables the GPT subsystem.
+ */
+#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__)
+#define HAL_USE_GPT TRUE
+#endif
+
+/**
+ * @brief Enables the I2C subsystem.
+ */
+#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__)
+#define HAL_USE_I2C FALSE
+#endif
+
+/**
+ * @brief Enables the I2S subsystem.
+ */
+#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__)
+#define HAL_USE_I2S FALSE
+#endif
+
+/**
+ * @brief Enables the ICU subsystem.
+ */
+#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__)
+#define HAL_USE_ICU FALSE
+#endif
+
+/**
+ * @brief Enables the MAC subsystem.
+ */
+#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__)
+#define HAL_USE_MAC FALSE
+#endif
+
+/**
+ * @brief Enables the MMC_SPI subsystem.
+ */
+#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__)
+#define HAL_USE_MMC_SPI FALSE
+#endif
+
+/**
+ * @brief Enables the PWM subsystem.
+ */
+#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__)
+#define HAL_USE_PWM FALSE
+#endif
+
+/**
+ * @brief Enables the QSPI subsystem.
+ */
+#if !defined(HAL_USE_QSPI) || defined(__DOXYGEN__)
+#define HAL_USE_QSPI FALSE
+#endif
+
+/**
+ * @brief Enables the RTC subsystem.
+ */
+#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__)
+#define HAL_USE_RTC FALSE
+#endif
+
+/**
+ * @brief Enables the SDC subsystem.
+ */
+#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__)
+#define HAL_USE_SDC FALSE
+#endif
+
+/**
+ * @brief Enables the SERIAL subsystem.
+ */
+#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__)
+#define HAL_USE_SERIAL FALSE
+#endif
+
+/**
+ * @brief Enables the SERIAL over USB subsystem.
+ */
+#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__)
+#define HAL_USE_SERIAL_USB FALSE
+#endif
+
+/**
+ * @brief Enables the SPI subsystem.
+ */
+#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__)
+#define HAL_USE_SPI FALSE
+#endif
+
+/**
+ * @brief Enables the UART subsystem.
+ */
+#if !defined(HAL_USE_UART) || defined(__DOXYGEN__)
+#define HAL_USE_UART FALSE
+#endif
+
+/**
+ * @brief Enables the USB subsystem.
+ */
+#if !defined(HAL_USE_USB) || defined(__DOXYGEN__)
+#define HAL_USE_USB TRUE
+#endif
+
+/**
+ * @brief Enables the WDG subsystem.
+ */
+#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__)
+#define HAL_USE_WDG FALSE
+#endif
+
+/*===========================================================================*/
+/* ADC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__)
+#define ADC_USE_WAIT TRUE
+#endif
+
+/**
+ * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define ADC_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+/*===========================================================================*/
+/* CAN driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Sleep mode related APIs inclusion switch.
+ */
+#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__)
+#define CAN_USE_SLEEP_MODE TRUE
+#endif
+
+/*===========================================================================*/
+/* I2C driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables the mutual exclusion APIs on the I2C bus.
+ */
+#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define I2C_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+/*===========================================================================*/
+/* MAC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables an event sources for incoming packets.
+ */
+#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__)
+#define MAC_USE_ZERO_COPY FALSE
+#endif
+
+/**
+ * @brief Enables an event sources for incoming packets.
+ */
+#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__)
+#define MAC_USE_EVENTS TRUE
+#endif
+
+/*===========================================================================*/
+/* MMC_SPI driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Delays insertions.
+ * @details If enabled this options inserts delays into the MMC waiting
+ * routines releasing some extra CPU time for the threads with
+ * lower priority, this may slow down the driver a bit however.
+ * This option is recommended also if the SPI driver does not
+ * use a DMA channel and heavily loads the CPU.
+ */
+#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__)
+#define MMC_NICE_WAITING TRUE
+#endif
+
+/*===========================================================================*/
+/* SDC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Number of initialization attempts before rejecting the card.
+ * @note Attempts are performed at 10mS intervals.
+ */
+#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__)
+#define SDC_INIT_RETRY 100
+#endif
+
+/**
+ * @brief Include support for MMC cards.
+ * @note MMC support is not yet implemented so this option must be kept
+ * at @p FALSE.
+ */
+#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__)
+#define SDC_MMC_SUPPORT FALSE
+#endif
+
+/**
+ * @brief Delays insertions.
+ * @details If enabled this options inserts delays into the MMC waiting
+ * routines releasing some extra CPU time for the threads with
+ * lower priority, this may slow down the driver a bit however.
+ */
+#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__)
+#define SDC_NICE_WAITING TRUE
+#endif
+
+/*===========================================================================*/
+/* SERIAL driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Default bit rate.
+ * @details Configuration parameter, this is the baud rate selected for the
+ * default configuration.
+ */
+#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__)
+#define SERIAL_DEFAULT_BITRATE 38400
+#endif
+
+/**
+ * @brief Serial buffers size.
+ * @details Configuration parameter, you can change the depth of the queue
+ * buffers depending on the requirements of your application.
+ * @note The default is 16 bytes for both the transmission and receive
+ * buffers.
+ */
+#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__)
+#define SERIAL_BUFFERS_SIZE 16
+#endif
+
+/*===========================================================================*/
+/* SERIAL_USB driver related setting. */
+/*===========================================================================*/
+
+/**
+ * @brief Serial over USB buffers size.
+ * @details Configuration parameter, the buffer size must be a multiple of
+ * the USB data endpoint maximum packet size.
+ * @note The default is 256 bytes for both the transmission and receive
+ * buffers.
+ */
+#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__)
+#define SERIAL_USB_BUFFERS_SIZE 1
+#endif
+
+/**
+ * @brief Serial over USB number of buffers.
+ * @note The default is 2 buffers.
+ */
+#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__)
+#define SERIAL_USB_BUFFERS_NUMBER 2
+#endif
+
+/*===========================================================================*/
+/* SPI driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__)
+#define SPI_USE_WAIT TRUE
+#endif
+
+/**
+ * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define SPI_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+/*===========================================================================*/
+/* UART driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__)
+#define UART_USE_WAIT FALSE
+#endif
+
+/**
+ * @brief Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define UART_USE_MUTUAL_EXCLUSION FALSE
+#endif
+
+/*===========================================================================*/
+/* USB driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__)
+#define USB_USE_WAIT TRUE
+#endif
+
+#endif /* HALCONF_H */
+
+/** @} */
--- /dev/null
+/*
+ ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+#ifndef MCUCONF_H
+#define MCUCONF_H
+
+/*
+ * STM32F3xx drivers configuration.
+ * The following settings override the default settings present in
+ * the various device driver implementation headers.
+ * Note that the settings for each driver only have effect if the whole
+ * driver is enabled in halconf.h.
+ *
+ * IRQ priorities:
+ * 15...0 Lowest...Highest.
+ *
+ * DMA priorities:
+ * 0...3 Lowest...Highest.
+ */
+
+#define STM32F3xx_MCUCONF
+
+/*
+ * HAL driver system settings.
+ */
+#define STM32_NO_INIT FALSE
+#define STM32_PVD_ENABLE FALSE
+#define STM32_PLS STM32_PLS_LEV0
+#define STM32_HSI_ENABLED TRUE
+#define STM32_LSI_ENABLED TRUE
+#define STM32_HSE_ENABLED TRUE
+#define STM32_LSE_ENABLED FALSE
+#define STM32_SW STM32_SW_PLL
+#define STM32_PLLSRC STM32_PLLSRC_HSE
+#define STM32_PREDIV_VALUE 1
+#define STM32_PLLMUL_VALUE 9
+#define STM32_HPRE STM32_HPRE_DIV1
+#define STM32_PPRE1 STM32_PPRE1_DIV2
+#define STM32_PPRE2 STM32_PPRE2_DIV2
+#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK
+#define STM32_ADC12PRES STM32_ADC12PRES_DIV1
+#define STM32_ADC34PRES STM32_ADC34PRES_DIV1
+#define STM32_USART1SW STM32_USART1SW_PCLK
+#define STM32_USART2SW STM32_USART2SW_PCLK
+#define STM32_USART3SW STM32_USART3SW_PCLK
+#define STM32_UART4SW STM32_UART4SW_PCLK
+#define STM32_UART5SW STM32_UART5SW_PCLK
+#define STM32_I2C1SW STM32_I2C1SW_SYSCLK
+#define STM32_I2C2SW STM32_I2C2SW_SYSCLK
+#define STM32_TIM1SW STM32_TIM1SW_PCLK2
+#define STM32_TIM8SW STM32_TIM8SW_PCLK2
+#define STM32_RTCSEL STM32_RTCSEL_LSI
+#define STM32_USB_CLOCK_REQUIRED TRUE
+#define STM32_USBPRE STM32_USBPRE_DIV1P5
+
+#undef STM32_HSE_BYPASS
+// #error "oh no"
+// #endif
+
+/*
+ * ADC driver system settings.
+ */
+#define STM32_ADC_DUAL_MODE FALSE
+#define STM32_ADC_COMPACT_SAMPLES FALSE
+#define STM32_ADC_USE_ADC1 FALSE
+#define STM32_ADC_USE_ADC2 FALSE
+#define STM32_ADC_USE_ADC3 FALSE
+#define STM32_ADC_USE_ADC4 FALSE
+#define STM32_ADC_ADC1_DMA_STREAM STM32_DMA_STREAM_ID(1, 1)
+#define STM32_ADC_ADC2_DMA_STREAM STM32_DMA_STREAM_ID(2, 1)
+#define STM32_ADC_ADC3_DMA_STREAM STM32_DMA_STREAM_ID(2, 5)
+#define STM32_ADC_ADC4_DMA_STREAM STM32_DMA_STREAM_ID(2, 2)
+#define STM32_ADC_ADC1_DMA_PRIORITY 2
+#define STM32_ADC_ADC2_DMA_PRIORITY 2
+#define STM32_ADC_ADC3_DMA_PRIORITY 2
+#define STM32_ADC_ADC4_DMA_PRIORITY 2
+#define STM32_ADC_ADC12_IRQ_PRIORITY 5
+#define STM32_ADC_ADC3_IRQ_PRIORITY 5
+#define STM32_ADC_ADC4_IRQ_PRIORITY 5
+#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY 5
+#define STM32_ADC_ADC2_DMA_IRQ_PRIORITY 5
+#define STM32_ADC_ADC3_DMA_IRQ_PRIORITY 5
+#define STM32_ADC_ADC4_DMA_IRQ_PRIORITY 5
+#define STM32_ADC_ADC12_CLOCK_MODE ADC_CCR_CKMODE_AHB_DIV1
+#define STM32_ADC_ADC34_CLOCK_MODE ADC_CCR_CKMODE_AHB_DIV1
+
+/*
+ * CAN driver system settings.
+ */
+#define STM32_CAN_USE_CAN1 FALSE
+#define STM32_CAN_CAN1_IRQ_PRIORITY 11
+
+/*
+ * DAC driver system settings.
+ */
+#define STM32_DAC_DUAL_MODE FALSE
+#define STM32_DAC_USE_DAC1_CH1 TRUE
+#define STM32_DAC_USE_DAC1_CH2 TRUE
+#define STM32_DAC_DAC1_CH1_IRQ_PRIORITY 10
+#define STM32_DAC_DAC1_CH2_IRQ_PRIORITY 10
+#define STM32_DAC_DAC1_CH1_DMA_PRIORITY 2
+#define STM32_DAC_DAC1_CH2_DMA_PRIORITY 2
+
+/*
+ * EXT driver system settings.
+ */
+#define STM32_EXT_EXTI0_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI1_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI2_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI3_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI4_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI16_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI17_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI18_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI19_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI20_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI21_22_29_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI30_32_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI33_IRQ_PRIORITY 6
+
+/*
+ * GPT driver system settings.
+ */
+#define STM32_GPT_USE_TIM1 FALSE
+#define STM32_GPT_USE_TIM2 FALSE
+#define STM32_GPT_USE_TIM3 FALSE
+#define STM32_GPT_USE_TIM4 FALSE
+#define STM32_GPT_USE_TIM6 TRUE
+#define STM32_GPT_USE_TIM7 TRUE
+#define STM32_GPT_USE_TIM8 TRUE
+#define STM32_GPT_TIM1_IRQ_PRIORITY 7
+#define STM32_GPT_TIM2_IRQ_PRIORITY 7
+#define STM32_GPT_TIM3_IRQ_PRIORITY 7
+#define STM32_GPT_TIM4_IRQ_PRIORITY 7
+#define STM32_GPT_TIM6_IRQ_PRIORITY 7
+#define STM32_GPT_TIM7_IRQ_PRIORITY 7
+#define STM32_GPT_TIM8_IRQ_PRIORITY 7
+
+/*
+ * I2C driver system settings.
+ */
+#define STM32_I2C_USE_I2C1 FALSE
+#define STM32_I2C_USE_I2C2 FALSE
+#define STM32_I2C_BUSY_TIMEOUT 50
+#define STM32_I2C_I2C1_IRQ_PRIORITY 10
+#define STM32_I2C_I2C2_IRQ_PRIORITY 10
+#define STM32_I2C_USE_DMA TRUE
+#define STM32_I2C_I2C1_DMA_PRIORITY 1
+#define STM32_I2C_I2C2_DMA_PRIORITY 1
+#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure")
+
+/*
+ * ICU driver system settings.
+ */
+#define STM32_ICU_USE_TIM1 FALSE
+#define STM32_ICU_USE_TIM2 FALSE
+#define STM32_ICU_USE_TIM3 FALSE
+#define STM32_ICU_USE_TIM4 FALSE
+#define STM32_ICU_USE_TIM8 FALSE
+#define STM32_ICU_TIM1_IRQ_PRIORITY 7
+#define STM32_ICU_TIM2_IRQ_PRIORITY 7
+#define STM32_ICU_TIM3_IRQ_PRIORITY 7
+#define STM32_ICU_TIM4_IRQ_PRIORITY 7
+#define STM32_ICU_TIM8_IRQ_PRIORITY 7
+
+/*
+ * PWM driver system settings.
+ */
+#define STM32_PWM_USE_ADVANCED FALSE
+#define STM32_PWM_USE_TIM1 FALSE
+#define STM32_PWM_USE_TIM2 FALSE
+#define STM32_PWM_USE_TIM3 FALSE
+#define STM32_PWM_USE_TIM4 FALSE
+#define STM32_PWM_USE_TIM8 FALSE
+#define STM32_PWM_TIM1_IRQ_PRIORITY 7
+#define STM32_PWM_TIM2_IRQ_PRIORITY 7
+#define STM32_PWM_TIM3_IRQ_PRIORITY 7
+#define STM32_PWM_TIM4_IRQ_PRIORITY 7
+#define STM32_PWM_TIM8_IRQ_PRIORITY 7
+
+/*
+ * SERIAL driver system settings.
+ */
+#define STM32_SERIAL_USE_USART1 FALSE
+#define STM32_SERIAL_USE_USART2 FALSE
+#define STM32_SERIAL_USE_USART3 FALSE
+#define STM32_SERIAL_USE_UART4 FALSE
+#define STM32_SERIAL_USE_UART5 FALSE
+#define STM32_SERIAL_USART1_PRIORITY 12
+#define STM32_SERIAL_USART2_PRIORITY 12
+#define STM32_SERIAL_USART3_PRIORITY 12
+#define STM32_SERIAL_UART4_PRIORITY 12
+#define STM32_SERIAL_UART5_PRIORITY 12
+
+/*
+ * SPI driver system settings.
+ */
+#define STM32_SPI_USE_SPI1 FALSE
+#define STM32_SPI_USE_SPI2 FALSE
+#define STM32_SPI_USE_SPI3 FALSE
+#define STM32_SPI_SPI1_DMA_PRIORITY 1
+#define STM32_SPI_SPI2_DMA_PRIORITY 1
+#define STM32_SPI_SPI3_DMA_PRIORITY 1
+#define STM32_SPI_SPI1_IRQ_PRIORITY 10
+#define STM32_SPI_SPI2_IRQ_PRIORITY 10
+#define STM32_SPI_SPI3_IRQ_PRIORITY 10
+#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure")
+
+/*
+ * ST driver system settings.
+ */
+#define STM32_ST_IRQ_PRIORITY 8
+#define STM32_ST_USE_TIMER 2
+
+/*
+ * UART driver system settings.
+ */
+#define STM32_UART_USE_USART1 FALSE
+#define STM32_UART_USE_USART2 FALSE
+#define STM32_UART_USE_USART3 FALSE
+#define STM32_UART_USART1_IRQ_PRIORITY 12
+#define STM32_UART_USART2_IRQ_PRIORITY 12
+#define STM32_UART_USART3_IRQ_PRIORITY 12
+#define STM32_UART_USART1_DMA_PRIORITY 0
+#define STM32_UART_USART2_DMA_PRIORITY 0
+#define STM32_UART_USART3_DMA_PRIORITY 0
+#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure")
+
+/*
+ * USB driver system settings.
+ */
+#define STM32_USB_USE_USB1 TRUE
+#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE
+#define STM32_USB_USB1_HP_IRQ_PRIORITY 13
+#define STM32_USB_USB1_LP_IRQ_PRIORITY 14
+
+/*
+ * WDG driver system settings.
+ */
+#define STM32_WDG_USE_IWDG FALSE
+
+#endif /* MCUCONF_H */
--- /dev/null
+# Clueboard 66%
+
+
+
+A fully customizable 66% keyboard.
+
+* Keyboard Maintainer: [Zach White](https://github.com/skullydazed)
+* Hardware Supported: Clueboard 66% PCB rev4 (stm32f303cc, PCB Version 3.0)
+* Hardware Availability: [clueboard.co](https://clueboard.co/)
+
+Make example for this keyboard (after setting up your build environment):
+
+ make clueboard/66/rev4:default
+
+See [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) then the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
--- /dev/null
+#include "rev4.h"
+//#include "backlight.h"
+
+void matrix_init_kb(void) {
+ // put your keyboard start-up code here
+ // runs once when the firmware starts up
+ matrix_init_user();
+ led_init_ports();
+}
+
+void matrix_scan_kb(void) {
+ matrix_scan_user();
+}
+
+void backlight_init_ports(void) {
+ print("init_backlight_pin()\n");
+ // Set our LED pins as output
+ //DDRD |= (1<<6); // Esc
+ //DDRB |= (1<<7); // Page Up
+ //DDRD |= (1<<4); // Arrows
+
+ // Set our LED pins low
+ //PORTD &= ~(1<<6); // Esc
+ //PORTB &= ~(1<<7); // Page Up
+ //PORTD &= ~(1<<4); // Arrows
+}
+
+void backlight_set(uint8_t level) {
+/*
+ if ( level == 0 ) {
+ // Turn off light
+ PORTD |= (1<<6); // Esc
+ PORTB |= (1<<7); // Page Up
+ PORTD |= (1<<4); // Arrows
+ } else {
+ // Turn on light
+ PORTD &= ~(1<<6); // Esc
+ PORTB &= ~(1<<7); // Page Up
+ PORTD &= ~(1<<4); // Arrows
+ }
+*/
+}
+
+void led_init_ports() {
+ // Set our LED pins as output
+ palSetPadMode(GPIOB, 13, PAL_MODE_OUTPUT_PUSHPULL); // LED1
+ palClearPad(GPIOB, 13);
+ palSetPadMode(GPIOB, 14, PAL_MODE_OUTPUT_PUSHPULL); // LED2
+ palClearPad(GPIOB, 14);
+ palSetPadMode(GPIOA, 8, PAL_MODE_OUTPUT_PUSHPULL); // LED3
+ palClearPad(GPIOA, 8);
+ palSetPadMode(GPIOA, 0, PAL_MODE_OUTPUT_PUSHPULL); // Capslock LED
+ palClearPad(GPIOA, 0);
+}
+
+void led_set_kb(uint8_t usb_led) {
+ if (usb_led & (1<<USB_LED_NUM_LOCK)) {
+ palSetPad(GPIOB, 13); // LED1
+ } else {
+ palClearPad(GPIOB, 13); // LED1
+ }
+
+ if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
+ palSetPad(GPIOA, 0); // Capslock LED
+ palSetPad(GPIOB, 14); // LED2
+ } else {
+ palClearPad(GPIOA, 0); // Capslock LED
+ palClearPad(GPIOB, 14); // LED2
+ }
+
+ if (usb_led & (1<<USB_LED_SCROLL_LOCK)) {
+ palSetPad(GPIOA, 8); // LED3
+ } else {
+ palClearPad(GPIOA, 8); // LED3
+ }
+}
--- /dev/null
+#pragma once
+
+#include "quantum.h"
+
+/* Clueboard matrix layout
+ * ,-----------------------------------------------------------. ,---.
+ * | 00| 01| 02| 03| 04| 05| 06| 07| 50| 51| 52| 53| 54| 55| 56| | 57|
+ * |-----------------------------------------------------------| |---|
+ * | 10| 11| 12| 13| 14| 15| 16| 17| 60| 61| 62| 63| 64| 65| | 67|
+ * |-----------------------------------------------------------| `---'
+ * | 20| 21| 22| 23| 24| 25| 26| 27| 70| 71| 72| 73| 74| 75|
+ * |------------------------------------------------------------.
+ * | 30| 31| 32| 33| 34| 35| 36| 37| 80| 81| 82| 83| 84| 85|86|
+ * |------------------------------------------------------------------.
+ * | 40| 41| 42| 43| 45| 46| 90| 92| 93| 94| 95| 96| 97|
+ * `------------------------------------------------------------------'
+ * ,-----------------------------------------------------------. ,---.
+ * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Yen| BS| |Ins|
+ * |-----------------------------------------------------------| |---|
+ * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| |Del|
+ * |-----------------------------------------------------------| `---'
+ * |Caps | A| S| D| F| G| H| J| k| L| ;| '| # | Ent|
+ * |--------------------------------------------------------------.
+ * |Shift| \| Z| X| C| V| B| N| M| ,| .| /| \|Shift| Up|
+ * |------------------------------------------------------------------.
+ * |Ctrl|Alt|Gui |MHen| Space| Space|Henk|Gui |Ctrl| Fn|Left|Down|Rgt|
+ * `------------------------------------------------------------------'
+ */
+// The first section contains all of the arguments
+// The second converts the arguments into a two-dimensional array
+
+#define LAYOUT_all( \
+ k00, k01, k02, k03, k04, k05, k06, k07, k50, k51, k52, k53, k54, k55, k56, k57, \
+ k10, k11, k12, k13, k14, k15, k16, k17, k60, k61, k62, k63, k64, k65, k67, \
+ k20, k21, k22, k23, k24, k25, k26, k27, k70, k71, k72, k73, k74, k75, \
+ k30, k31, k32, k33, k34, k35, k36, k37, k80, k81, k82, k83, k84, k85, k86, \
+ k40, k41, k42, k43, k45, k46, k90, k92, k93, k94, k95, k96, k97 \
+) { \
+ { k00, k01, k02, k03, k04, k05, k06, k07 }, \
+ { k10, k11, k12, k13, k14, k15, k16, k17 }, \
+ { k20, k21, k22, k23, k24, k25, k26, k27 }, \
+ { k30, k31, k32, k33, k34, k35, k36, k37 }, \
+ { k40, k41, k42, k43, KC_NO, k45, k46, KC_NO }, \
+ { k50, k51, k52, k53, k54, k55, k56, k57 }, \
+ { k60, k61, k62, k63, k64, k65, KC_NO, k67 }, \
+ { k70, k71, k72, k73, k74, k75, KC_NO, KC_NO }, \
+ { k80, k81, k82, k83, k84, k85, k86, KC_NO }, \
+ { k90, KC_NO, k92, k93, k94, k95, k96, k97 } \
+}
+
+/* LAYOUT_66_ansi, standard 66 key ANSI layout
+ */
+#define LAYOUT_66_ansi( \
+ k00, k01, k02, k03, k04, k05, k06, k07, k50, k51, k52, k53, k54, k56, k57, \
+ k10, k11, k12, k13, k14, k15, k16, k17, k60, k61, k62, k63, k64, k65, k67, \
+ k20, k21, k22, k23, k24, k25, k26, k27, k70, k71, k72, k73, k75, \
+ k30, k32, k33, k34, k35, k36, k37, k80, k81, k82, k83, k85, k86, \
+ k40, k41, k42, k46, k92, k93, k94, k95, k96, k97 \
+) { \
+ { k00, k01, k02, k03, k04, k05, k06, k07 }, \
+ { k10, k11, k12, k13, k14, k15, k16, k17 }, \
+ { k20, k21, k22, k23, k24, k25, k26, k27 }, \
+ { k30, KC_NO, k32, k33, k34, k35, k36, k37 }, \
+ { k40, k41, k42, KC_NO, KC_NO, KC_NO, k46, KC_NO }, \
+ { k50, k51, k52, k53, k54, KC_NO, k56, k57 }, \
+ { k60, k61, k62, k63, k64, k65, KC_NO, k67 }, \
+ { k70, k71, k72, k73, KC_NO, k75, KC_NO, KC_NO }, \
+ { k80, k81, k82, k83, KC_NO, k85, k86, KC_NO }, \
+ { KC_NO, KC_NO, k92, k93, k94, k95, k96, k97 } \
+}
+
+/* LAYOUT_66_iso, standard 67 key ISO layout
+ */
+#define LAYOUT_66_iso( \
+ k00, k01, k02, k03, k04, k05, k06, k07, k50, k51, k52, k53, k54, k56, k57, \
+ k10, k11, k12, k13, k14, k15, k16, k17, k60, k61, k62, k63, k64, k67, \
+ k20, k21, k22, k23, k24, k25, k26, k27, k70, k71, k72, k73, k74, k75, \
+ k30, k31, k32, k33, k34, k35, k36, k37, k80, k81, k82, k83, k85, k86, \
+ k40, k41, k42, k46, k92, k93, k94, k95, k96, k97 \
+) { \
+ { k00, k01, k02, k03, k04, k05, k06, k07 }, \
+ { k10, k11, k12, k13, k14, k15, k16, k17 }, \
+ { k20, k21, k22, k23, k24, k25, k26, k27 }, \
+ { k30, k31, k32, k33, k34, k35, k36, k37 }, \
+ { k40, k41, k42, KC_NO, KC_NO, KC_NO, k46, KC_NO }, \
+ { k50, k51, k52, k53, k54, KC_NO, k56, k57 }, \
+ { k60, k61, k62, k63, k64, KC_NO, KC_NO, k67 }, \
+ { k70, k71, k72, k73, k74, k75, KC_NO, KC_NO }, \
+ { k80, k81, k82, k83, KC_NO, k85, k86, KC_NO }, \
+ { KC_NO, KC_NO, k92, k93, k94, k95, k96, k97 } \
+}
+
+#define KEYMAP LAYOUT_all
+#define LAYOUT LAYOUT_all
--- /dev/null
+LAYOUTS = 66_ansi 66_iso
+
+## chip/board settings
+MCU_FAMILY = STM32
+MCU_SERIES = STM32F3xx
+MCU_LDSCRIPT = STM32F303xC
+MCU_STARTUP = stm32f3xx
+BOARD = GENERIC_STM32_F303XC
+MCU = cortex-m4
+ARMV = 7
+USE_FPU = yes
+OPT_DEFS =
+
+# Options to pass to dfu-util when flashing
+DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave
+
+# Build Options
+# comment out to disable the options.
+#
+BACKLIGHT_ENABLE = yes
+BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = yes # Console for debug(+400)
+COMMAND_ENABLE = no # Commands for debug and configuration
+NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+AUDIO_ENABLE = no
+RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality
+MIDI_ENABLE = no # MIDI controls
+UNICODE_ENABLE = no # Unicode
+BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = yes
projects / qmk_firmware.git / commitdiff