--- /dev/null
+/*
+ ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+#include "hal.h"
+
+// Value to place in RTC backup register 10 for persistent bootloader mode
+#define RTC_BOOTLOADER_FLAG 0x424C
+
+/**
+ * @brief PAL setup.
+ * @details Digital I/O ports static configuration as defined in @p board.h.
+ * This variable is used by the HAL when initializing the PAL driver.
+ */
+#if HAL_USE_PAL || defined(__DOXYGEN__)
+const PALConfig pal_default_config =
+{
+ {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH},
+ {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH},
+ {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH},
+ {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH},
+ {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH},
+};
+#endif
+
+/*
+ * Early initialization code.
+ * This initialization must be performed just after stack setup and before
+ * any other initialization.
+ */
+void __early_init(void) {
+
+ stm32_clock_init();
+}
+
+/*
+ * Board-specific initialization code.
+ */
+void boardInit(void) {
+ //JTAG-DP Disabled and SW-DP Enabled
+ AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_JTAGDISABLE;
+ //Set backup register DR10 to enter bootloader on reset
+ BKP->DR10 = RTC_BOOTLOADER_FLAG;
+}
--- /dev/null
+/*
+ ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * Setup for a Generic STM32F103 board.
+ */
+
+/*
+ * Board identifier.
+ */
+#define BOARD_GENERIC_STM32_F103
+#define BOARD_NAME "Generic STM32F103x board"
+
+/*
+ * Board frequencies.
+ */
+#define STM32_LSECLK 32768
+#define STM32_HSECLK 8000000
+
+/*
+ * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
+ */
+#define STM32F103xB
+
+/*
+ * IO pins assignments
+ */
+
+/* on-board */
+
+#define GPIOA_LED 8
+#define GPIOD_OSC_IN 0
+#define GPIOD_OSC_OUT 1
+
+/* In case your board has a "USB enable" hardware
+ controlled by a pin, define it here. (It could be just
+ a 1.5k resistor connected to D+ line.)
+*/
+/*
+#define GPIOB_USB_DISC 10
+*/
+
+/*
+ * I/O ports initial setup, this configuration is established soon after reset
+ * in the initialization code.
+ *
+ * The digits have the following meaning:
+ * 0 - Analog input.
+ * 1 - Push Pull output 10MHz.
+ * 2 - Push Pull output 2MHz.
+ * 3 - Push Pull output 50MHz.
+ * 4 - Digital input.
+ * 5 - Open Drain output 10MHz.
+ * 6 - Open Drain output 2MHz.
+ * 7 - Open Drain output 50MHz.
+ * 8 - Digital input with PullUp or PullDown resistor depending on ODR.
+ * 9 - Alternate Push Pull output 10MHz.
+ * A - Alternate Push Pull output 2MHz.
+ * B - Alternate Push Pull output 50MHz.
+ * C - Reserved.
+ * D - Alternate Open Drain output 10MHz.
+ * E - Alternate Open Drain output 2MHz.
+ * F - Alternate Open Drain output 50MHz.
+ * Please refer to the STM32 Reference Manual for details.
+ */
+
+/*
+ * Port A setup.
+ * Everything input with pull-up except:
+ * PA2 - Alternate output (USART2 TX).
+ * PA3 - Normal input (USART2 RX).
+ * PA9 - Alternate output (USART1 TX).
+ * PA10 - Normal input (USART1 RX).
+ */
+#define VAL_GPIOACRL 0x88884B88 /* PA7...PA0 */
+#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */
+#define VAL_GPIOAODR 0xFFFFFFFF
+
+/*
+ * Port B setup.
+ * Everything input with pull-up except:
+ * PB10 - Push Pull output (USB switch).
+ */
+#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */
+#define VAL_GPIOBCRH 0x88888388 /* PB15...PB8 */
+#define VAL_GPIOBODR 0xFFFFFFFF
+
+/*
+ * Port C setup.
+ * Everything input with pull-up except:
+ * PC13 - Push Pull output (LED).
+ */
+#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
+#define VAL_GPIOCCRH 0x88388888 /* PC15...PC8 */
+#define VAL_GPIOCODR 0xFFFFFFFF
+
+/*
+ * Port D setup.
+ * Everything input with pull-up except:
+ * PD0 - Normal input (XTAL).
+ * PD1 - Normal input (XTAL).
+ */
+#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
+#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
+#define VAL_GPIODODR 0xFFFFFFFF
+
+/*
+ * Port E setup.
+ * Everything input with pull-up except:
+ */
+#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
+#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
+#define VAL_GPIOEODR 0xFFFFFFFF
+
+/*
+ * USB bus activation macro, required by the USB driver.
+ */
+/* The point is that most of the generic STM32F103* boards
+ have a 1.5k resistor connected on one end to the D+ line
+ and on the other end to some pin. Or even a slightly more
+ complicated "USB enable" circuit, controlled by a pin.
+ That should go here.
+
+ However on some boards (e.g. one that I have), there's no
+ such hardware. In which case it's better to not do anything.
+*/
+/*
+#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC)
+*/
+#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT);
+
+/*
+ * USB bus de-activation macro, required by the USB driver.
+ */
+/*
+#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC)
+*/
+#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12);
+
+#if !defined(_FROM_ASM_)
+#ifdef __cplusplus
+extern "C" {
+#endif
+ void boardInit(void);
+#ifdef __cplusplus
+}
+#endif
+#endif /* _FROM_ASM_ */
+
+#endif /* _BOARD_H_ */
--- /dev/null
+# List of all the board related files.
+BOARDSRC = $(BOARD_PATH)/boards/GENERIC_STM32_F103/board.c
+
+# Required include directories
+BOARDINC = $(BOARD_PATH)/boards/GENERIC_STM32_F103
--- /dev/null
+/* Address for jumping to bootloader on STM32 chips. */
+/* It is chip dependent, the correct number can be looked up here (page 175):
+ * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
+ * This also requires a patch to chibios:
+ * <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
+ */
+
+// STM32F103* does NOT have an USB bootloader in ROM (only serial),
+// so setting anything here does not make much sense
+// #define STM32_BOOTLOADER_ADDRESS 0x1FFFC800
--- /dev/null
+/*
+ ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+/**
+ * @file templates/chconf.h
+ * @brief Configuration file template.
+ * @details A copy of this file must be placed in each project directory, it
+ * contains the application specific kernel settings.
+ *
+ * @addtogroup config
+ * @details Kernel related settings and hooks.
+ * @{
+ */
+
+#ifndef CHCONF_H
+#define CHCONF_H
+
+#define _CHIBIOS_RT_CONF_
+
+/*===========================================================================*/
+/**
+ * @name System timers settings
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief System time counter resolution.
+ * @note Allowed values are 16 or 32 bits.
+ */
+#define CH_CFG_ST_RESOLUTION 32
+
+/**
+ * @brief System tick frequency.
+ * @details Frequency of the system timer that drives the system ticks. This
+ * setting also defines the system tick time unit.
+ */
+#define CH_CFG_ST_FREQUENCY 100000
+
+/**
+ * @brief Time delta constant for the tick-less mode.
+ * @note If this value is zero then the system uses the classic
+ * periodic tick. This value represents the minimum number
+ * of ticks that is safe to specify in a timeout directive.
+ * The value one is not valid, timeouts are rounded up to
+ * this value.
+ */
+#define CH_CFG_ST_TIMEDELTA 0
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Kernel parameters and options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Round robin interval.
+ * @details This constant is the number of system ticks allowed for the
+ * threads before preemption occurs. Setting this value to zero
+ * disables the preemption for threads with equal priority and the
+ * round robin becomes cooperative. Note that higher priority
+ * threads can still preempt, the kernel is always preemptive.
+ * @note Disabling the round robin preemption makes the kernel more compact
+ * and generally faster.
+ * @note The round robin preemption is not supported in tickless mode and
+ * must be set to zero in that case.
+ */
+#define CH_CFG_TIME_QUANTUM 0
+
+/**
+ * @brief Managed RAM size.
+ * @details Size of the RAM area to be managed by the OS. If set to zero
+ * then the whole available RAM is used. The core memory is made
+ * available to the heap allocator and/or can be used directly through
+ * the simplified core memory allocator.
+ *
+ * @note In order to let the OS manage the whole RAM the linker script must
+ * provide the @p __heap_base__ and @p __heap_end__ symbols.
+ * @note Requires @p CH_CFG_USE_MEMCORE.
+ */
+#define CH_CFG_MEMCORE_SIZE 0
+
+/**
+ * @brief Idle thread automatic spawn suppression.
+ * @details When this option is activated the function @p chSysInit()
+ * does not spawn the idle thread. The application @p main()
+ * function becomes the idle thread and must implement an
+ * infinite loop.
+ */
+#define CH_CFG_NO_IDLE_THREAD FALSE
+
+/* Use __WFI in the idle thread for waiting. Does lower the power
+ * consumption. */
+#define CORTEX_ENABLE_WFI_IDLE TRUE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Performance options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief OS optimization.
+ * @details If enabled then time efficient rather than space efficient code
+ * is used when two possible implementations exist.
+ *
+ * @note This is not related to the compiler optimization options.
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_OPTIMIZE_SPEED TRUE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Subsystem options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Time Measurement APIs.
+ * @details If enabled then the time measurement APIs are included in
+ * the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_TM FALSE
+
+/**
+ * @brief Threads registry APIs.
+ * @details If enabled then the registry APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_REGISTRY TRUE
+
+/**
+ * @brief Threads synchronization APIs.
+ * @details If enabled then the @p chThdWait() function is included in
+ * the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_WAITEXIT TRUE
+
+/**
+ * @brief Semaphores APIs.
+ * @details If enabled then the Semaphores APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_SEMAPHORES TRUE
+
+/**
+ * @brief Semaphores queuing mode.
+ * @details If enabled then the threads are enqueued on semaphores by
+ * priority rather than in FIFO order.
+ *
+ * @note The default is @p FALSE. Enable this if you have special
+ * requirements.
+ * @note Requires @p CH_CFG_USE_SEMAPHORES.
+ */
+#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE
+
+/**
+ * @brief Mutexes APIs.
+ * @details If enabled then the mutexes APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_MUTEXES TRUE
+
+/**
+ * @brief Enables recursive behavior on mutexes.
+ * @note Recursive mutexes are heavier and have an increased
+ * memory footprint.
+ *
+ * @note The default is @p FALSE.
+ * @note Requires @p CH_CFG_USE_MUTEXES.
+ */
+#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE
+
+/**
+ * @brief Conditional Variables APIs.
+ * @details If enabled then the conditional variables APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_MUTEXES.
+ */
+#define CH_CFG_USE_CONDVARS TRUE
+
+/**
+ * @brief Conditional Variables APIs with timeout.
+ * @details If enabled then the conditional variables APIs with timeout
+ * specification are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_CONDVARS.
+ */
+#define CH_CFG_USE_CONDVARS_TIMEOUT FALSE
+
+/**
+ * @brief Events Flags APIs.
+ * @details If enabled then the event flags APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_EVENTS TRUE
+
+/**
+ * @brief Events Flags APIs with timeout.
+ * @details If enabled then the events APIs with timeout specification
+ * are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_EVENTS.
+ */
+#define CH_CFG_USE_EVENTS_TIMEOUT TRUE
+
+/**
+ * @brief Synchronous Messages APIs.
+ * @details If enabled then the synchronous messages APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_MESSAGES TRUE
+
+/**
+ * @brief Synchronous Messages queuing mode.
+ * @details If enabled then messages are served by priority rather than in
+ * FIFO order.
+ *
+ * @note The default is @p FALSE. Enable this if you have special
+ * requirements.
+ * @note Requires @p CH_CFG_USE_MESSAGES.
+ */
+#define CH_CFG_USE_MESSAGES_PRIORITY FALSE
+
+/**
+ * @brief Mailboxes APIs.
+ * @details If enabled then the asynchronous messages (mailboxes) APIs are
+ * included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_SEMAPHORES.
+ */
+#define CH_CFG_USE_MAILBOXES TRUE
+
+/**
+ * @brief Core Memory Manager APIs.
+ * @details If enabled then the core memory manager APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_MEMCORE TRUE
+
+/**
+ * @brief Heap Allocator APIs.
+ * @details If enabled then the memory heap allocator APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or
+ * @p CH_CFG_USE_SEMAPHORES.
+ * @note Mutexes are recommended.
+ */
+#define CH_CFG_USE_HEAP TRUE
+
+/**
+ * @brief Memory Pools Allocator APIs.
+ * @details If enabled then the memory pools allocator APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#define CH_CFG_USE_MEMPOOLS FALSE
+
+/**
+ * @brief Dynamic Threads APIs.
+ * @details If enabled then the dynamic threads creation APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_CFG_USE_WAITEXIT.
+ * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS.
+ */
+#define CH_CFG_USE_DYNAMIC FALSE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Debug options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Debug option, kernel statistics.
+ *
+ * @note The default is @p FALSE.
+ */
+#define CH_DBG_STATISTICS FALSE
+
+/**
+ * @brief Debug option, system state check.
+ * @details If enabled the correct call protocol for system APIs is checked
+ * at runtime.
+ *
+ * @note The default is @p FALSE.
+ */
+#define CH_DBG_SYSTEM_STATE_CHECK FALSE
+
+/**
+ * @brief Debug option, parameters checks.
+ * @details If enabled then the checks on the API functions input
+ * parameters are activated.
+ *
+ * @note The default is @p FALSE.
+ */
+#define CH_DBG_ENABLE_CHECKS FALSE
+
+/**
+ * @brief Debug option, consistency checks.
+ * @details If enabled then all the assertions in the kernel code are
+ * activated. This includes consistency checks inside the kernel,
+ * runtime anomalies and port-defined checks.
+ *
+ * @note The default is @p FALSE.
+ */
+#define CH_DBG_ENABLE_ASSERTS FALSE
+
+/**
+ * @brief Debug option, trace buffer.
+ * @details If enabled then the trace buffer is activated.
+ *
+ * @note The default is @p CH_DBG_TRACE_MASK_DISABLED.
+ */
+#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED
+
+/**
+ * @brief Trace buffer entries.
+ * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is
+ * different from @p CH_DBG_TRACE_MASK_DISABLED.
+ */
+#define CH_DBG_TRACE_BUFFER_SIZE 128
+
+/**
+ * @brief Debug option, stack checks.
+ * @details If enabled then a runtime stack check is performed.
+ *
+ * @note The default is @p FALSE.
+ * @note The stack check is performed in a architecture/port dependent way.
+ * It may not be implemented or some ports.
+ * @note The default failure mode is to halt the system with the global
+ * @p panic_msg variable set to @p NULL.
+ */
+#define CH_DBG_ENABLE_STACK_CHECK FALSE
+
+/**
+ * @brief Debug option, stacks initialization.
+ * @details If enabled then the threads working area is filled with a byte
+ * value when a thread is created. This can be useful for the
+ * runtime measurement of the used stack.
+ *
+ * @note The default is @p FALSE.
+ */
+#define CH_DBG_FILL_THREADS FALSE
+
+/**
+ * @brief Debug option, threads profiling.
+ * @details If enabled then a field is added to the @p thread_t structure that
+ * counts the system ticks occurred while executing the thread.
+ *
+ * @note The default is @p FALSE.
+ * @note This debug option is not currently compatible with the
+ * tickless mode.
+ */
+#define CH_DBG_THREADS_PROFILING FALSE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Kernel hooks
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Threads descriptor structure extension.
+ * @details User fields added to the end of the @p thread_t structure.
+ */
+#define CH_CFG_THREAD_EXTRA_FIELDS \
+ /* Add threads custom fields here.*/
+
+/**
+ * @brief Threads initialization hook.
+ * @details User initialization code added to the @p chThdInit() API.
+ *
+ * @note It is invoked from within @p chThdInit() and implicitly from all
+ * the threads creation APIs.
+ */
+#define CH_CFG_THREAD_INIT_HOOK(tp) { \
+ /* Add threads initialization code here.*/ \
+}
+
+/**
+ * @brief Threads finalization hook.
+ * @details User finalization code added to the @p chThdExit() API.
+ */
+#define CH_CFG_THREAD_EXIT_HOOK(tp) { \
+ /* Add threads finalization code here.*/ \
+}
+
+/**
+ * @brief Context switch hook.
+ * @details This hook is invoked just before switching between threads.
+ */
+#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \
+ /* Context switch code here.*/ \
+}
+
+/**
+ * @brief ISR enter hook.
+ */
+#define CH_CFG_IRQ_PROLOGUE_HOOK() { \
+ /* IRQ prologue code here.*/ \
+}
+
+/**
+ * @brief ISR exit hook.
+ */
+#define CH_CFG_IRQ_EPILOGUE_HOOK() { \
+ /* IRQ epilogue code here.*/ \
+}
+
+/**
+ * @brief Idle thread enter hook.
+ * @note This hook is invoked within a critical zone, no OS functions
+ * should be invoked from here.
+ * @note This macro can be used to activate a power saving mode.
+ */
+#define CH_CFG_IDLE_ENTER_HOOK() { \
+ /* Idle-enter code here.*/ \
+}
+
+/**
+ * @brief Idle thread leave hook.
+ * @note This hook is invoked within a critical zone, no OS functions
+ * should be invoked from here.
+ * @note This macro can be used to deactivate a power saving mode.
+ */
+#define CH_CFG_IDLE_LEAVE_HOOK() { \
+ /* Idle-leave code here.*/ \
+}
+
+/**
+ * @brief Idle Loop hook.
+ * @details This hook is continuously invoked by the idle thread loop.
+ */
+#define CH_CFG_IDLE_LOOP_HOOK() { \
+ /* Idle loop code here.*/ \
+}
+
+/**
+ * @brief System tick event hook.
+ * @details This hook is invoked in the system tick handler immediately
+ * after processing the virtual timers queue.
+ */
+#define CH_CFG_SYSTEM_TICK_HOOK() { \
+ /* System tick event code here.*/ \
+}
+
+/**
+ * @brief System halt hook.
+ * @details This hook is invoked in case to a system halting error before
+ * the system is halted.
+ */
+#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \
+ /* System halt code here.*/ \
+}
+
+/**
+ * @brief Trace hook.
+ * @details This hook is invoked each time a new record is written in the
+ * trace buffer.
+ */
+#define CH_CFG_TRACE_HOOK(tep) { \
+ /* Trace code here.*/ \
+}
+
+/** @} */
+
+/*===========================================================================*/
+/* Port-specific settings (override port settings defaulted in chcore.h). */
+/*===========================================================================*/
+
+#endif /* CHCONF_H */
+
+/** @} */
--- /dev/null
+/*
+Copyright 2015 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x6464
+#define DEVICE_VER 0x0001
+/* in python2: list(u"whatever".encode('utf-16-le')) */
+/* at most 32 characters or the ugly hack in usb_main.c borks */
+#define MANUFACTURER QMK
+#define PRODUCT Ortho60
+#define DESCRIPTION Ortho60
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 12
+
+#define MATRIX_COL_PINS { B11, B10, B1, B0, A7, A6, A5, A4, A3, A2, A1, A0 }
+#define MATRIX_ROW_PINS { B3, B4, B5, B6, B7 }
+#define DIODE_DIRECTION COL2ROW
+
+#define BACKLIGHT_LEVELS 1
+
+/* define if matrix has ghost */
+//#define MATRIX_HAS_GHOST
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCE 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+
+
+/*
+ * Feature disable options
+ * These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
--- /dev/null
+/*
+ ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+/**
+ * @file templates/halconf.h
+ * @brief HAL configuration header.
+ * @details HAL configuration file, this file allows to enable or disable the
+ * various device drivers from your application. You may also use
+ * this file in order to override the device drivers default settings.
+ *
+ * @addtogroup HAL_CONF
+ * @{
+ */
+
+#ifndef _HALCONF_H_
+#define _HALCONF_H_
+
+#include "mcuconf.h"
+
+/**
+ * @brief Enables the PAL subsystem.
+ */
+#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__)
+#define HAL_USE_PAL TRUE
+#endif
+
+/**
+ * @brief Enables the ADC subsystem.
+ */
+#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__)
+#define HAL_USE_ADC FALSE
+#endif
+
+/**
+ * @brief Enables the CAN subsystem.
+ */
+#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__)
+#define HAL_USE_CAN FALSE
+#endif
+
+/**
+ * @brief Enables the DAC subsystem.
+ */
+#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__)
+#define HAL_USE_DAC FALSE
+#endif
+
+/**
+ * @brief Enables the EXT subsystem.
+ */
+#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__)
+#define HAL_USE_EXT FALSE
+#endif
+
+/**
+ * @brief Enables the GPT subsystem.
+ */
+#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__)
+#define HAL_USE_GPT FALSE
+#endif
+
+/**
+ * @brief Enables the I2C subsystem.
+ */
+#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__)
+#define HAL_USE_I2C FALSE
+#endif
+
+/**
+ * @brief Enables the I2S subsystem.
+ */
+#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__)
+#define HAL_USE_I2S FALSE
+#endif
+
+/**
+ * @brief Enables the ICU subsystem.
+ */
+#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__)
+#define HAL_USE_ICU FALSE
+#endif
+
+/**
+ * @brief Enables the MAC subsystem.
+ */
+#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__)
+#define HAL_USE_MAC FALSE
+#endif
+
+/**
+ * @brief Enables the MMC_SPI subsystem.
+ */
+#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__)
+#define HAL_USE_MMC_SPI FALSE
+#endif
+
+/**
+ * @brief Enables the PWM subsystem.
+ */
+#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__)
+#define HAL_USE_PWM FALSE
+#endif
+
+/**
+ * @brief Enables the RTC subsystem.
+ */
+#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__)
+#define HAL_USE_RTC FALSE
+#endif
+
+/**
+ * @brief Enables the SDC subsystem.
+ */
+#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__)
+#define HAL_USE_SDC FALSE
+#endif
+
+/**
+ * @brief Enables the SERIAL subsystem.
+ */
+#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__)
+#define HAL_USE_SERIAL FALSE
+#endif
+
+/**
+ * @brief Enables the SERIAL over USB subsystem.
+ */
+#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__)
+#define HAL_USE_SERIAL_USB FALSE
+#endif
+
+/**
+ * @brief Enables the SPI subsystem.
+ */
+#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__)
+#define HAL_USE_SPI TRUE
+#endif
+
+/**
+ * @brief Enables the UART subsystem.
+ */
+#if !defined(HAL_USE_UART) || defined(__DOXYGEN__)
+#define HAL_USE_UART FALSE
+#endif
+
+/**
+ * @brief Enables the USB subsystem.
+ */
+#if !defined(HAL_USE_USB) || defined(__DOXYGEN__)
+#define HAL_USE_USB TRUE
+#endif
+
+/**
+ * @brief Enables the WDG subsystem.
+ */
+#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__)
+#define HAL_USE_WDG FALSE
+#endif
+
+/*===========================================================================*/
+/* ADC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__)
+#define ADC_USE_WAIT TRUE
+#endif
+
+/**
+ * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define ADC_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+/*===========================================================================*/
+/* CAN driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Sleep mode related APIs inclusion switch.
+ */
+#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__)
+#define CAN_USE_SLEEP_MODE TRUE
+#endif
+
+/*===========================================================================*/
+/* I2C driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables the mutual exclusion APIs on the I2C bus.
+ */
+#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define I2C_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+/*===========================================================================*/
+/* MAC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables an event sources for incoming packets.
+ */
+#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__)
+#define MAC_USE_ZERO_COPY FALSE
+#endif
+
+/**
+ * @brief Enables an event sources for incoming packets.
+ */
+#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__)
+#define MAC_USE_EVENTS TRUE
+#endif
+
+/*===========================================================================*/
+/* MMC_SPI driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Delays insertions.
+ * @details If enabled this options inserts delays into the MMC waiting
+ * routines releasing some extra CPU time for the threads with
+ * lower priority, this may slow down the driver a bit however.
+ * This option is recommended also if the SPI driver does not
+ * use a DMA channel and heavily loads the CPU.
+ */
+#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__)
+#define MMC_NICE_WAITING TRUE
+#endif
+
+/*===========================================================================*/
+/* SDC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Number of initialization attempts before rejecting the card.
+ * @note Attempts are performed at 10mS intervals.
+ */
+#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__)
+#define SDC_INIT_RETRY 100
+#endif
+
+/**
+ * @brief Include support for MMC cards.
+ * @note MMC support is not yet implemented so this option must be kept
+ * at @p FALSE.
+ */
+#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__)
+#define SDC_MMC_SUPPORT FALSE
+#endif
+
+/**
+ * @brief Delays insertions.
+ * @details If enabled this options inserts delays into the MMC waiting
+ * routines releasing some extra CPU time for the threads with
+ * lower priority, this may slow down the driver a bit however.
+ */
+#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__)
+#define SDC_NICE_WAITING TRUE
+#endif
+
+/*===========================================================================*/
+/* SERIAL driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Default bit rate.
+ * @details Configuration parameter, this is the baud rate selected for the
+ * default configuration.
+ */
+#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__)
+#define SERIAL_DEFAULT_BITRATE 38400
+#endif
+
+/**
+ * @brief Serial buffers size.
+ * @details Configuration parameter, you can change the depth of the queue
+ * buffers depending on the requirements of your application.
+ * @note The default is 64 bytes for both the transmission and receive
+ * buffers.
+ */
+#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__)
+#define SERIAL_BUFFERS_SIZE 16
+#endif
+
+/*===========================================================================*/
+/* SERIAL_USB driver related setting. */
+/*===========================================================================*/
+
+/**
+ * @brief Serial over USB buffers size.
+ * @details Configuration parameter, the buffer size must be a multiple of
+ * the USB data endpoint maximum packet size.
+ * @note The default is 64 bytes for both the transmission and receive
+ * buffers.
+ */
+#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__)
+#define SERIAL_USB_BUFFERS_SIZE 1
+#endif
+
+/*===========================================================================*/
+/* SPI driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__)
+#define SPI_USE_WAIT TRUE
+#endif
+
+/**
+ * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define SPI_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+/*===========================================================================*/
+/* USB driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__)
+#define USB_USE_WAIT TRUE
+#endif
+
+#endif /* _HALCONF_H_ */
+
+/** @} */
--- /dev/null
+/* hsv2rgb.c
+ * Integer only conversion functions between HSV and RGB
+ */
+
+#include "hsv2rgb.h"
+
+// TODO fix these buggy macros
+#define max(x,y) ((x>y) ? x:y)
+#define min(x,y) ((x>y) ? y:x)
+#define min3(x,y,z) (min(min(x,y),z))
+#define max3(x,y,z) (max(max(x,y),z))
+
+
+rgb_color hsv2rgb(hsv_color hsv)
+{
+ // From : http://qscribble.blogspot.fr/2008/06/integer-conversion-from-hsl-to-rgb.html
+ int h = hsv.h;
+ int s = hsv.s;
+ int v = hsv.v;
+ rgb_color rgb = {0, 0, 0};
+
+ if (v == 0)
+ return rgb;
+
+ // sextant = 0 .. 5
+ int sextant = (h*6)/256;
+ // f = 0 .. 42
+ int f = h - (sextant*256)/6;
+
+ int p = (v * (256 - s))/256;
+ int q = (v * (256*43 - s*f))/(256*43);
+ int t = (v * (256*43 - s*(43-f)))/(256*43);
+
+ // Corrige les erreurs dues aux arrondis
+ p = max(min(p, 255), 0);
+ q = max(min(q, 255), 0);
+ t = max(min(t, 255), 0);
+
+ switch(sextant){
+ case 0: rgb.r = v; rgb.g = t; rgb.b = p; break;
+ case 1: rgb.r = q; rgb.g = v; rgb.b = p; break;
+ case 2: rgb.r = p; rgb.g = v; rgb.b = t; break;
+ case 3: rgb.r = p; rgb.g = q; rgb.b = v; break;
+ case 4: rgb.r = t; rgb.g = p; rgb.b = v; break;
+ default:rgb.r = v; rgb.g = p; rgb.b = q; break;
+ }
+ return rgb;
+}
+
+
+hsv_color rgb2hsv(rgb_color rgb)
+{
+ // From : http://www.ruinelli.ch/rgb-to-hsv
+ hsv_color hsv = {0, 0, 0};
+ int min, max, delta;
+
+ min = min3(rgb.r, rgb.g, rgb.b);
+ max = max3(rgb.r, rgb.g, rgb.b);
+
+ if(max==0) {
+ hsv.h = 0;
+ hsv.s = 0;
+ hsv.v = 0;
+ return hsv;
+ }
+
+ hsv.v = max;
+ delta = max - min;
+
+ hsv.s = (delta)*255 / max;
+
+ if(rgb.r == max)
+ hsv.h = (rgb.g - rgb.b)*42/delta; // between yellow & magenta
+ else if(rgb.g == max)
+ hsv.h = 120 + (rgb.b - rgb.r)*42/delta; // between cyan & yellow
+ else
+ hsv.h = 240 + (rgb.r - rgb.g)*42/delta; // between magenta & cyan
+
+ return hsv;
+}
\ No newline at end of file
--- /dev/null
+/* hsv2rgb.h
+ * Convert Hue Saturation Value to Red Green Blue
+ *
+ * Programme de convertion d'une information HSV en RGB
+ */
+#ifndef HSV2RGB_H
+#define HSV2RGB_H
+
+typedef struct {
+ unsigned char h;
+ unsigned char s;
+ unsigned char v;
+} hsv_color;
+
+typedef struct {
+ unsigned char r;
+ unsigned char g;
+ unsigned char b;
+} rgb_color;
+
+rgb_color hsv2rgb(hsv_color hsv);
+
+#endif
\ No newline at end of file
--- /dev/null
+{
+ "keyboard_name": "Ortho60",
+ "url": "",
+ "maintainer": "qmk",
+ "width": 12,
+ "height": 5,
+ "layouts": {
+ "LAYOUT_ortho_5x12": {
+ "layout": [
+ {"label":"`", "x":0, "y":0},
+ {"label":"1", "x":1, "y":0},
+ {"label":"2", "x":2, "y":0},
+ {"label":"3", "x":3, "y":0},
+ {"label":"4", "x":4, "y":0},
+ {"label":"5", "x":5, "y":0},
+ {"label":"6", "x":6, "y":0},
+ {"label":"7", "x":7, "y":0},
+ {"label":"8", "x":8, "y":0},
+ {"label":"9", "x":9, "y":0},
+ {"label":"0", "x":10, "y":0},
+ {"label":"Backspace", "x":11, "y":0},
+ {"label":"Tab", "x":0, "y":1},
+ {"label":"Q", "x":1, "y":1},
+ {"label":"W", "x":2, "y":1},
+ {"label":"E", "x":3, "y":1},
+ {"label":"R", "x":4, "y":1},
+ {"label":"T", "x":5, "y":1},
+ {"label":"Y", "x":6, "y":1},
+ {"label":"U", "x":7, "y":1},
+ {"label":"I", "x":8, "y":1},
+ {"label":"O", "x":9, "y":1},
+ {"label":"P", "x":10, "y":1},
+ {"label":"Delete", "x":11, "y":1},
+ {"label":"Esc", "x":0, "y":2},
+ {"label":"A", "x":1, "y":2},
+ {"label":"S", "x":2, "y":2},
+ {"label":"D", "x":3, "y":2},
+ {"label":"F", "x":4, "y":2},
+ {"label":"G", "x":5, "y":2},
+ {"label":"H", "x":6, "y":2},
+ {"label":"J", "x":7, "y":2},
+ {"label":"K", "x":8, "y":2},
+ {"label":"L", "x":9, "y":2},
+ {"label":";", "x":10, "y":2},
+ {"label":"'", "x":11, "y":2},
+ {"label":"Shift", "x":0, "y":3},
+ {"label":"Z", "x":1, "y":3},
+ {"label":"X", "x":2, "y":3},
+ {"label":"C", "x":3, "y":3},
+ {"label":"V", "x":4, "y":3},
+ {"label":"B", "x":5, "y":3},
+ {"label":"N", "x":6, "y":3},
+ {"label":"M", "x":7, "y":3},
+ {"label":",", "x":8, "y":3},
+ {"label":".", "x":9, "y":3},
+ {"label":"/", "x":10, "y":3},
+ {"label":"Enter", "x":11, "y":3},
+ {"label":"Fn", "x":0, "y":4},
+ {"label":"Ctrl", "x":1, "y":4},
+ {"label":"Alt", "x":2, "y":4},
+ {"label":"Meta", "x":3, "y":4},
+ {"label":"Lower", "x":4, "y":4},
+ {"label":"Space", "x":5, "y":4},
+ {"label":"Space", "x":6, "y":4},
+ {"label":"Raise", "x":7, "y":4},
+ {"label":"Left", "x":8, "y":4},
+ {"label":"Down", "x":9, "y":4},
+ {"label":"Right", "x":10, "y":4},
+ {"label":"up", "x":11, "y":4}
+ ]
+ }
+ }
+}
--- /dev/null
+/*
+Copyright 2012,2013 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+#include QMK_KEYBOARD_H
+
+extern keymap_config_t keymap_config;
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _BASE 0
+#define _RAISE 1
+#define _LOWER 2
+
+enum custom_keycodes {
+ QWERTY = SAFE_RANGE,
+ LOWER,
+ RAISE
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+/* Qwerty
+ * ,-----------------------------------------------------------------------------------.
+ * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | Tab | Q | W | E | R | T | Y | U | I | O | P | Del |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | Esc | A | S | D | F | G | H | J | K | L | ; | " |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * | Shift| Z | X | C | V | B | N | M | , | . | / |Enter |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | Brite| Ctrl | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_BASE] = LAYOUT_ortho_5x12( \
+ KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC, \
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_DEL, \
+ KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, \
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT, \
+ BL_TOGG, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT \
+),
+/* Lower
+ * ,-----------------------------------------------------------------------------------.
+ * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Bksp |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Del |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | Del | F1 | F2 | F3 | F4 | F5 | F6 | _ | + | { | } | | |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO ~ |ISO | | | | |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | | Next | Vol- | Vol+ | Play |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_LOWER] = LAYOUT_ortho_5x12( \
+ KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_BSPC, \
+ KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL, \
+ KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE, \
+ _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12,S(KC_NUHS),S(KC_NUBS),KC_HOME, KC_END, _______, \
+ _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \
+),
+
+/* Raise
+ * ,-----------------------------------------------------------------------------------.
+ * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Del |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | Del | F1 | F2 | F3 | F4 | F5 | F6 | - | = | [ | ] | \ |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO # |ISO / | | | |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | | Next | Vol- | Vol+ | Play |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_RAISE] = LAYOUT_ortho_5x12( \
+ KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC, \
+ KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL, \
+ KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS, \
+ _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_NUHS, KC_NUBS, KC_PGUP, KC_PGDN, _______, \
+ _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \
+)
+};
--- /dev/null
+/*
+ * Copyright (C) 2013-2016 Fabio Utzig, http://fabioutzig.com
+ * (C) 2016 flabbergast <s3+flabbergast@sdfeu.org>
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining
+ * a copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS
+ * OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+ * SOFTWARE.
+ */
+
+/*
+ * KL26Z64 memory setup.
+ */
+MEMORY
+{
+ flash0 : org = 0x00000000, len = 0x100
+ flash1 : org = 0x00000400, len = 0x10
+ flash2 : org = 0x00000410, len = 62k - 0x410
+ flash3 : org = 0x0000F800, len = 2k
+ flash4 : org = 0x00000000, len = 0
+ flash5 : org = 0x00000000, len = 0
+ flash6 : org = 0x00000000, len = 0
+ flash7 : org = 0x00000000, len = 0
+ ram0 : org = 0x1FFFF800, len = 8k
+ ram1 : org = 0x00000000, len = 0
+ ram2 : org = 0x00000000, len = 0
+ ram3 : org = 0x00000000, len = 0
+ ram4 : org = 0x00000000, len = 0
+ ram5 : org = 0x00000000, len = 0
+ ram6 : org = 0x00000000, len = 0
+ ram7 : org = 0x00000000, len = 0
+}
+
+/* Flash region for the configuration bytes.*/
+SECTIONS
+{
+ .cfmprotect : ALIGN(4) SUBALIGN(4)
+ {
+ KEEP(*(.cfmconfig))
+ } > flash1
+}
+
+/* For each data/text section two region are defined, a virtual region
+ and a load region (_LMA suffix).*/
+
+/* Flash region to be used for exception vectors.*/
+REGION_ALIAS("VECTORS_FLASH", flash0);
+REGION_ALIAS("VECTORS_FLASH_LMA", flash0);
+
+/* Flash region to be used for constructors and destructors.*/
+REGION_ALIAS("XTORS_FLASH", flash2);
+REGION_ALIAS("XTORS_FLASH_LMA", flash2);
+
+/* Flash region to be used for code text.*/
+REGION_ALIAS("TEXT_FLASH", flash2);
+REGION_ALIAS("TEXT_FLASH_LMA", flash2);
+
+/* Flash region to be used for read only data.*/
+REGION_ALIAS("RODATA_FLASH", flash2);
+REGION_ALIAS("RODATA_FLASH_LMA", flash2);
+
+/* Flash region to be used for various.*/
+REGION_ALIAS("VARIOUS_FLASH", flash2);
+REGION_ALIAS("VARIOUS_FLASH_LMA", flash2);
+
+/* Flash region to be used for RAM(n) initialization data.*/
+REGION_ALIAS("RAM_INIT_FLASH_LMA", flash2);
+
+/* RAM region to be used for Main stack. This stack accommodates the processing
+ of all exceptions and interrupts.*/
+REGION_ALIAS("MAIN_STACK_RAM", ram0);
+
+/* RAM region to be used for the process stack. This is the stack used by
+ the main() function.*/
+REGION_ALIAS("PROCESS_STACK_RAM", ram0);
+
+/* RAM region to be used for data segment.*/
+REGION_ALIAS("DATA_RAM", ram0);
+REGION_ALIAS("DATA_RAM_LMA", flash2);
+
+/* RAM region to be used for BSS segment.*/
+REGION_ALIAS("BSS_RAM", ram0);
+
+/* RAM region to be used for the default heap.*/
+REGION_ALIAS("HEAP_RAM", ram0);
+
+__eeprom_workarea_start__ = ORIGIN(flash3);
+__eeprom_workarea_size__ = LENGTH(flash3);
+__eeprom_workarea_end__ = __eeprom_workarea_start__ + __eeprom_workarea_size__;
+
+/* Generic rules inclusion.*/
+INCLUDE rules.ld
--- /dev/null
+/*
+ ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+/*
+ * ST32F103xB memory setup for use with the maplemini bootloader.
+ * You will have to
+ * #define CORTEX_VTOR_INIT 0x5000
+ * in your projects chconf.h
+ */
+MEMORY
+{
+ flash0 : org = 0x08002000, len = 64k - 0x2000
+ flash1 : org = 0x00000000, len = 0
+ flash2 : org = 0x00000000, len = 0
+ flash3 : org = 0x00000000, len = 0
+ flash4 : org = 0x00000000, len = 0
+ flash5 : org = 0x00000000, len = 0
+ flash6 : org = 0x00000000, len = 0
+ flash7 : org = 0x00000000, len = 0
+ ram0 : org = 0x20000000, len = 20k
+ ram1 : org = 0x00000000, len = 0
+ ram2 : org = 0x00000000, len = 0
+ ram3 : org = 0x00000000, len = 0
+ ram4 : org = 0x00000000, len = 0
+ ram5 : org = 0x00000000, len = 0
+ ram6 : org = 0x00000000, len = 0
+ ram7 : org = 0x00000000, len = 0
+}
+
+/* For each data/text section two region are defined, a virtual region
+ and a load region (_LMA suffix).*/
+
+/* Flash region to be used for exception vectors.*/
+REGION_ALIAS("VECTORS_FLASH", flash0);
+REGION_ALIAS("VECTORS_FLASH_LMA", flash0);
+
+/* Flash region to be used for constructors and destructors.*/
+REGION_ALIAS("XTORS_FLASH", flash0);
+REGION_ALIAS("XTORS_FLASH_LMA", flash0);
+
+/* Flash region to be used for code text.*/
+REGION_ALIAS("TEXT_FLASH", flash0);
+REGION_ALIAS("TEXT_FLASH_LMA", flash0);
+
+/* Flash region to be used for read only data.*/
+REGION_ALIAS("RODATA_FLASH", flash0);
+REGION_ALIAS("RODATA_FLASH_LMA", flash0);
+
+/* Flash region to be used for various.*/
+REGION_ALIAS("VARIOUS_FLASH", flash0);
+REGION_ALIAS("VARIOUS_FLASH_LMA", flash0);
+
+/* Flash region to be used for RAM(n) initialization data.*/
+REGION_ALIAS("RAM_INIT_FLASH_LMA", flash0);
+
+/* RAM region to be used for Main stack. This stack accommodates the processing
+ of all exceptions and interrupts.*/
+REGION_ALIAS("MAIN_STACK_RAM", ram0);
+
+/* RAM region to be used for the process stack. This is the stack used by
+ the main() function.*/
+REGION_ALIAS("PROCESS_STACK_RAM", ram0);
+
+/* RAM region to be used for data segment.*/
+REGION_ALIAS("DATA_RAM", ram0);
+REGION_ALIAS("DATA_RAM_LMA", flash0);
+
+/* RAM region to be used for BSS segment.*/
+REGION_ALIAS("BSS_RAM", ram0);
+
+/* RAM region to be used for the default heap.*/
+REGION_ALIAS("HEAP_RAM", ram0);
+
+/* Generic rules inclusion.*/
+INCLUDE rules.ld
--- /dev/null
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include "hal.h"
+#include "backlight.h"
+#include "led.h"
+#include "printf.h"
+
+void backlight_init_ports(void) {
+ printf("backlight_init_ports()\n");
+ #ifdef BACKLIGHT_ENABLE
+ palSetPadMode(GPIOA, 8, PAL_MODE_OUTPUT_PUSHPULL);
+ palSetPad(GPIOA, 8);
+ #endif
+}
+
+void backlight_set(uint8_t level) {
+ printf("backlight_set(%d)\n", level);
+ #ifdef BACKLIGHT_ENABLE
+ if (level == 0) {
+ // Turn backlight off
+ palSetPad(GPIOA, 8);
+ } else {
+ // Turn backlight on
+ palClearPad(GPIOA, 8);
+ }
+ #endif
+}
+
+void led_set(uint8_t usb_led)
+{
+ if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
+ palClearPad(GPIOC, 13);
+ } else {
+ palSetPad(GPIOC, 13);
+ }
+}
--- /dev/null
+/*
+ ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+#ifndef _MCUCONF_H_
+#define _MCUCONF_H_
+
+#define STM32F103_MCUCONF
+
+/*
+ * STM32F103 drivers configuration.
+ * The following settings override the default settings present in
+ * the various device driver implementation headers.
+ * Note that the settings for each driver only have effect if the whole
+ * driver is enabled in halconf.h.
+ *
+ * IRQ priorities:
+ * 15...0 Lowest...Highest.
+ *
+ * DMA priorities:
+ * 0...3 Lowest...Highest.
+ */
+
+/*
+ * HAL driver system settings.
+ */
+#define STM32_NO_INIT FALSE
+#define STM32_HSI_ENABLED TRUE
+#define STM32_LSI_ENABLED FALSE
+#define STM32_HSE_ENABLED TRUE
+#define STM32_LSE_ENABLED FALSE
+#define STM32_SW STM32_SW_PLL
+#define STM32_PLLSRC STM32_PLLSRC_HSE
+#define STM32_PLLXTPRE STM32_PLLXTPRE_DIV1
+#define STM32_PLLMUL_VALUE 9
+#define STM32_HPRE STM32_HPRE_DIV1
+#define STM32_PPRE1 STM32_PPRE1_DIV2
+#define STM32_PPRE2 STM32_PPRE2_DIV2
+#define STM32_ADCPRE STM32_ADCPRE_DIV4
+#define STM32_USB_CLOCK_REQUIRED TRUE
+#define STM32_USBPRE STM32_USBPRE_DIV1P5
+#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK
+#define STM32_RTCSEL STM32_RTCSEL_HSEDIV
+#define STM32_PVD_ENABLE FALSE
+#define STM32_PLS STM32_PLS_LEV0
+
+/*
+ * ADC driver system settings.
+ */
+#define STM32_ADC_USE_ADC1 FALSE
+#define STM32_ADC_ADC1_DMA_PRIORITY 2
+#define STM32_ADC_ADC1_IRQ_PRIORITY 6
+
+/*
+ * CAN driver system settings.
+ */
+#define STM32_CAN_USE_CAN1 FALSE
+#define STM32_CAN_CAN1_IRQ_PRIORITY 11
+
+/*
+ * EXT driver system settings.
+ */
+#define STM32_EXT_EXTI0_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI1_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI2_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI3_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI4_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI16_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI17_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI18_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI19_IRQ_PRIORITY 6
+
+/*
+ * GPT driver system settings.
+ */
+#define STM32_GPT_USE_TIM1 FALSE
+#define STM32_GPT_USE_TIM2 FALSE
+#define STM32_GPT_USE_TIM3 FALSE
+#define STM32_GPT_USE_TIM4 FALSE
+#define STM32_GPT_USE_TIM5 FALSE
+#define STM32_GPT_USE_TIM8 FALSE
+#define STM32_GPT_TIM1_IRQ_PRIORITY 7
+#define STM32_GPT_TIM2_IRQ_PRIORITY 7
+#define STM32_GPT_TIM3_IRQ_PRIORITY 7
+#define STM32_GPT_TIM4_IRQ_PRIORITY 7
+#define STM32_GPT_TIM5_IRQ_PRIORITY 7
+#define STM32_GPT_TIM8_IRQ_PRIORITY 7
+
+/*
+ * I2C driver system settings.
+ */
+#define STM32_I2C_USE_I2C1 FALSE
+#define STM32_I2C_USE_I2C2 FALSE
+#define STM32_I2C_BUSY_TIMEOUT 50
+#define STM32_I2C_I2C1_IRQ_PRIORITY 5
+#define STM32_I2C_I2C2_IRQ_PRIORITY 5
+#define STM32_I2C_I2C1_DMA_PRIORITY 3
+#define STM32_I2C_I2C2_DMA_PRIORITY 3
+#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure")
+
+/*
+ * ICU driver system settings.
+ */
+#define STM32_ICU_USE_TIM1 FALSE
+#define STM32_ICU_USE_TIM2 FALSE
+#define STM32_ICU_USE_TIM3 FALSE
+#define STM32_ICU_USE_TIM4 FALSE
+#define STM32_ICU_USE_TIM5 FALSE
+#define STM32_ICU_USE_TIM8 FALSE
+#define STM32_ICU_TIM1_IRQ_PRIORITY 7
+#define STM32_ICU_TIM2_IRQ_PRIORITY 7
+#define STM32_ICU_TIM3_IRQ_PRIORITY 7
+#define STM32_ICU_TIM4_IRQ_PRIORITY 7
+#define STM32_ICU_TIM5_IRQ_PRIORITY 7
+#define STM32_ICU_TIM8_IRQ_PRIORITY 7
+
+/*
+ * PWM driver system settings.
+ */
+#define STM32_PWM_USE_ADVANCED FALSE
+#define STM32_PWM_USE_TIM1 FALSE
+#define STM32_PWM_USE_TIM2 FALSE
+#define STM32_PWM_USE_TIM3 FALSE
+#define STM32_PWM_USE_TIM4 FALSE
+#define STM32_PWM_USE_TIM5 FALSE
+#define STM32_PWM_USE_TIM8 FALSE
+#define STM32_PWM_TIM1_IRQ_PRIORITY 7
+#define STM32_PWM_TIM2_IRQ_PRIORITY 7
+#define STM32_PWM_TIM3_IRQ_PRIORITY 7
+#define STM32_PWM_TIM4_IRQ_PRIORITY 7
+#define STM32_PWM_TIM5_IRQ_PRIORITY 7
+#define STM32_PWM_TIM8_IRQ_PRIORITY 7
+
+/*
+ * RTC driver system settings.
+ */
+#define STM32_RTC_IRQ_PRIORITY 15
+
+/*
+ * SERIAL driver system settings.
+ */
+#define STM32_SERIAL_USE_USART1 FALSE
+#define STM32_SERIAL_USE_USART2 FALSE
+#define STM32_SERIAL_USE_USART3 FALSE
+#define STM32_SERIAL_USE_UART4 FALSE
+#define STM32_SERIAL_USE_UART5 FALSE
+#define STM32_SERIAL_USART1_PRIORITY 12
+#define STM32_SERIAL_USART2_PRIORITY 12
+#define STM32_SERIAL_USART3_PRIORITY 12
+#define STM32_SERIAL_UART4_PRIORITY 12
+#define STM32_SERIAL_UART5_PRIORITY 12
+
+/*
+ * SPI driver system settings.
+ */
+#define STM32_SPI_USE_SPI1 FALSE
+#define STM32_SPI_USE_SPI2 TRUE
+#define STM32_SPI_USE_SPI3 FALSE
+#define STM32_SPI_SPI1_DMA_PRIORITY 1
+#define STM32_SPI_SPI2_DMA_PRIORITY 1
+#define STM32_SPI_SPI3_DMA_PRIORITY 1
+#define STM32_SPI_SPI1_IRQ_PRIORITY 10
+#define STM32_SPI_SPI2_IRQ_PRIORITY 10
+#define STM32_SPI_SPI3_IRQ_PRIORITY 10
+#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure")
+
+/*
+ * ST driver system settings.
+ */
+#define STM32_ST_IRQ_PRIORITY 8
+#define STM32_ST_USE_TIMER 2
+
+/*
+ * UART driver system settings.
+ */
+#define STM32_UART_USE_USART1 FALSE
+#define STM32_UART_USE_USART2 FALSE
+#define STM32_UART_USE_USART3 FALSE
+#define STM32_UART_USART1_IRQ_PRIORITY 12
+#define STM32_UART_USART2_IRQ_PRIORITY 12
+#define STM32_UART_USART3_IRQ_PRIORITY 12
+#define STM32_UART_USART1_DMA_PRIORITY 0
+#define STM32_UART_USART2_DMA_PRIORITY 0
+#define STM32_UART_USART3_DMA_PRIORITY 0
+#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure")
+
+/*
+ * USB driver system settings.
+ */
+#define STM32_USB_USE_USB1 TRUE
+#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE
+#define STM32_USB_USB1_HP_IRQ_PRIORITY 13
+#define STM32_USB_USB1_LP_IRQ_PRIORITY 14
+
+#endif /* _MCUCONF_H_ */
--- /dev/null
+
+#include "ortho60.h"
+
+#include "ch.h"
+#include "hal.h"
+
+#include "underglow.h"
+#include "print.h"
+#include "debug.h"
+#include "util.h"
+
+/* generic STM32F103C8T6 board */
+#ifdef BOARD_GENERIC_STM32_F103
+#define LED_ON() do { palClearPad(GPIOC, 13) ;} while (0)
+#define LED_OFF() do { palSetPad(GPIOC, 13); } while (0)
+#define LED_TGL() do { palTogglePad(GPIOC, 13); } while (0)
+#endif
+
+void matrix_init_kb(void){
+ /* MOSI pin*/
+ palSetPadMode(GPIOB, 15, PAL_MODE_STM32_ALTERNATE_PUSHPULL);
+
+ LED_ON();
+ palSetPad(GPIOA, 8);
+ wait_ms(500);
+ palClearPad(GPIOA, 8);
+ LED_OFF();
+
+ leds_init();
+
+
+}
--- /dev/null
+#pragma once
+
+#include "quantum.h"
+
+#define LAYOUT_1x2uC( \
+ k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, \
+ k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, \
+ k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, \
+ k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, \
+ k40, k41, k42, k43, k44, k45 , k47, k48, k49, k4a, k4b \
+) \
+{ \
+ { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b }, \
+ { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b }, \
+ { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b }, \
+ { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b }, \
+ { k40, k41, k42, k43, k44, k45, KC_NO, k47, k48, k49, k4a, k4b }, \
+}
+
+#define LAYOUT_ortho_5x12( \
+ k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, \
+ k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, \
+ k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, \
+ k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, \
+ k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4a, k4b \
+) \
+{ \
+ { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b }, \
+ { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b }, \
+ { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b }, \
+ { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b }, \
+ { k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4a, k4b }, \
+}
--- /dev/null
+# Ortho 60
+
+Blue Pill STM32F103C8T6 based 12x5 Ortholinear Board
--- /dev/null
+# project specific files
+SRC = led.c \
+ underglow.c \
+ hsv2rgb.c
+
+# GENERIC STM32F103C8T6 board - stm32duino bootloader
+OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000
+MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader
+BOARD = GENERIC_STM32_F103
+
+# OPT_DEFS =
+# MCU_LDSCRIPT = STM32F103x8
+# BOARD = GENERIC_STM32_F103
+
+## chip/board settings
+# the next two should match the directories in
+# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
+MCU_FAMILY = STM32
+MCU_SERIES = STM32F1xx
+# linker script to use
+# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
+# or <this_dir>/ld/
+# startup code to use
+# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
+MCU_STARTUP = stm32f1xx
+# it should exist either in <chibios>/os/hal/boards/
+# or <this_dir>/boards
+# Cortex version
+# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
+MCU = cortex-m3
+# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
+ARMV = 7
+# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
+# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
+# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
+# a custom board definition that you plan to reuse).
+# If you're not setting it here, leave it commented out.
+# It is chip dependent, the correct number can be looked up here (page 175):
+# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
+# This also requires a patch to chibios:
+# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
+#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
+
+
+#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration
+MOUSEKEY_ENABLE = yes # Mouse keys
+EXTRAKEY_ENABLE = yes # Audio control and System control
+CONSOLE_ENABLE = yes # Console for debug
+COMMAND_ENABLE = yes # Commands for debug and configuration
+SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes
+
+LAYOUTS = ortho_5x12
+
+DEFAULT_FOLDER = handwired/ortho60
--- /dev/null
+#include "ch.h"
+#include "hal.h"
+
+#include "hsv2rgb.h"
+#include "underglow.h"
+
+#define BYTES_FOR_LED_BYTE 4
+#define NB_COLORS 3
+#define BYTES_FOR_LED BYTES_FOR_LED_BYTE*NB_COLORS
+#define DATA_SIZE BYTES_FOR_LED*NB_LEDS
+#define RESET_SIZE 200
+#define PREAMBLE_SIZE 4
+
+// Define the spi your LEDs are plugged to here
+#define LEDS_SPI SPID2
+// Define the number of LEDs you wish to control in your LED strip
+#define NB_LEDS 8
+
+#define LED_SPIRAL 1
+
+static uint8_t txbuf[PREAMBLE_SIZE + DATA_SIZE + RESET_SIZE];
+static uint8_t get_protocol_eq(uint8_t data, int pos);
+
+/*
+ * This lib is meant to be used asynchronously, thus the colors contained in
+ * the txbuf will be sent in loop, so that the colors are always the ones you
+ * put in the table (the user thus have less to worry about)
+ *
+ * Since the data are sent via DMA, and the call to spiSend is a blocking one,
+ * the processor ressources are not used to much, if you see your program being
+ * too slow, simply add a:
+ * chThdSleepMilliseconds(x);
+ * after the spiSend, where you increment x untill you are satisfied with your
+ * program speed, another trick may be to lower this thread priority : your call
+ */
+static THD_WORKING_AREA(LEDS_THREAD_WA, 128);
+static THD_FUNCTION(ledsThread, arg) {
+ (void) arg;
+ while(1){
+ spiSend(&LEDS_SPI, PREAMBLE_SIZE + DATA_SIZE + RESET_SIZE, txbuf);
+ }
+}
+
+#if LED_SPIRAL
+/*
+ * 'Led spiral' is a simple demo in which we put all the leds to the same
+ * color, where this color does all the hsv circle in loop.
+ * If you want to launch the thread that will chage the led colors to the
+ * appropriate value, simply set LED_SPIRAL to 1.
+ */
+static THD_WORKING_AREA(HSVTRANS_WA, 128);
+static THD_FUNCTION(hsv_transThread, arg){
+ (void) arg;
+ hsv_color color = {0, 255, 127};
+ while(1){
+ color.h += 1;
+ color.h %= 256;
+ set_leds_color_hsv(color);
+ chThdSleepMilliseconds(50);
+ }
+}
+#endif
+
+static const SPIConfig spicfg = {
+ NULL,
+ GPIOB,
+ 15,
+ SPI_CR1_BR_1|SPI_CR1_BR_0 // baudrate : fpclk / 8 => 1tick is 0.32us
+};
+
+/*
+ * Function used to initialize the driver.
+ *
+ * Starts by shutting off all the LEDs.
+ * Then gets access on the LED_SPI driver.
+ * May eventually launch an animation on the LEDs (e.g. a thread setting the
+ * txbuff values)
+ */
+void leds_init(void){
+ for(int i = 0; i < RESET_SIZE; i++)
+ txbuf[DATA_SIZE+i] = 0x00;
+ for (int i=0; i<PREAMBLE_SIZE; i++)
+ txbuf[i] = 0x00;
+ spiAcquireBus(&LEDS_SPI); /* Acquire ownership of the bus. */
+ spiStart(&LEDS_SPI, &spicfg); /* Setup transfer parameters. */
+ spiSelect(&LEDS_SPI); /* Slave Select assertion. */
+ chThdCreateStatic(LEDS_THREAD_WA, sizeof(LEDS_THREAD_WA),NORMALPRIO, ledsThread, NULL);
+#if LED_SPIRAL
+ chThdCreateStatic(HSVTRANS_WA, sizeof(HSVTRANS_WA),
+ NORMALPRIO, hsv_transThread, NULL);
+#endif
+}
+
+/*
+ * As the trick here is to use the SPI to send a huge pattern of 0 and 1 to
+ * the ws2812b protocol, we use this helper function to translate bytes into
+ * 0s and 1s for the LED (with the appropriate timing).
+ */
+static uint8_t get_protocol_eq(uint8_t data, int pos){
+ uint8_t eq = 0;
+ if (data & (1 << (2*(3-pos))))
+ eq = 0b1110;
+ else
+ eq = 0b1000;
+ if (data & (2 << (2*(3-pos))))
+ eq += 0b11100000;
+ else
+ eq += 0b10000000;
+ return eq;
+}
+
+/*
+ * If you want to set a LED's color in the HSV color space, simply call this
+ * function with a hsv_color containing the desired color and the index of the
+ * led on the LED strip (starting from 0, the first one being the closest the
+ * first plugged to the board)
+ *
+ * Only set the color of the LEDs through the functions given by this API
+ * (unless you really know what you are doing)
+ */
+void set_led_color_hsv(hsv_color color, int pos){
+ set_led_color_rgb(hsv2rgb(color), pos);
+}
+
+/*
+ * If you want to set a LED's color in the RGB color space, simply call this
+ * function with a hsv_color containing the desired color and the index of the
+ * led on the LED strip (starting from 0, the first one being the closest the
+ * first plugged to the board)
+ *
+ * Only set the color of the LEDs through the functions given by this API
+ * (unless you really know what you are doing)
+ */
+void set_led_color_rgb(rgb_color color, int pos){
+ for(int j = 0; j < 4; j++)
+ txbuf[PREAMBLE_SIZE + BYTES_FOR_LED*pos + j] = get_protocol_eq(color.g, j);
+ for(int j = 0; j < 4; j++)
+ txbuf[PREAMBLE_SIZE + BYTES_FOR_LED*pos + BYTES_FOR_LED_BYTE+j] = get_protocol_eq(color.r, j);
+ for(int j = 0; j < 4; j++)
+ txbuf[PREAMBLE_SIZE + BYTES_FOR_LED*pos + BYTES_FOR_LED_BYTE*2+j] = get_protocol_eq(color.b, j);
+}
+
+/*
+ * Same as the two above, but sets all the LEDs in the LED strip (HSV)
+ */
+void set_leds_color_hsv(hsv_color color){
+ for(int i = 0; i < NB_LEDS; i++)
+ set_led_color_hsv(color, i);
+}
+
+/*
+ * Same as the two above, but sets all the LEDs in the LED strip (RGB)
+ */
+void set_leds_color_rgb(rgb_color color){
+ for(int i = 0; i < NB_LEDS; i++)
+ set_led_color_rgb(color, i);
+}
\ No newline at end of file
--- /dev/null
+#pragma once
+
+#include "hsv2rgb.h"
+
+void set_leds_color_hsv(hsv_color color);
+void set_leds_color_rgb(rgb_color color);
+void set_led_color_hsv(hsv_color color, int pos);
+void set_led_color_rgb(rgb_color color, int pos);
+
+void leds_init(void);
projects / qmk_firmware.git / commitdiff