Clueboard refresh (#4902)

[qmk_firmware.git] / keyboards / clueboard / card / rules.mk

diff --git a/keyboards/clueboard/card/rules.mk b/keyboards/clueboard/card/rules.mk
index 2117c8127287d3f53afca4ff0a01ab146ed35c58..37b439e75a7a18d1bf8ee0e13adcebf79e243c97 100644 (file)
--- a/keyboards/clueboard/card/rules.mk
+++ b/keyboards/clueboard/card/rules.mk
@@ -1,70 +1,21 @@
-
-
-# MCU name
-#MCU = at90usb1287
 MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
 F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
 ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
 OPT_DEFS += -DBOOTLOADER_SIZE=4096
 
 
 # Build Options
-#   change yes to no to disable
-#
 BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = yes        # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = no            # USB Nkey Rollover
-RGBLIGHT_ENABLE = yes       # Enable keyboard underlight functionality (+4870)
-BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality by default
-MIDI_ENABLE = no            # MIDI controls
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = yes           # Audio output on port C6
+MOUSEKEY_ENABLE = yes      # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes      # Audio control and System control(+450)
+CONSOLE_ENABLE = yes       # Console for debug(+400)
+COMMAND_ENABLE = yes       # Commands for debug and configuration
+NKRO_ENABLE = no           # USB Nkey Rollover
+RGBLIGHT_ENABLE = yes      # Enable keyboard underlight functionality (+4870)
+BACKLIGHT_ENABLE = yes     # Enable keyboard backlight functionality by default
+MIDI_ENABLE = no           # MIDI controls
+UNICODE_ENABLE = no        # Unicode
+BLUETOOTH_ENABLE = no      # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = yes         # Audio output on port C6