--- /dev/null
+/**
+ ******************************************************************************
+ * @file stm32f4xx_hal_rtc.c
+ * @author MCD Application Team
+ * @version V1.1.0
+ * @date 19-June-2014
+ * @brief RTC HAL module driver.
+ * This file provides firmware functions to manage the following
+ * functionalities of the Real Time Clock (RTC) peripheral:
+ * + Initialization and de-initialization functions
+ * + RTC Time and Date functions
+ * + RTC Alarm functions
+ * + Peripheral Control functions
+ * + Peripheral State functions
+ *
+ @verbatim
+ ==============================================================================
+ ##### Backup Domain Operating Condition #####
+ ==============================================================================
+ [..] The real-time clock (RTC), the RTC backup registers, and the backup
+ SRAM (BKP SRAM) can be powered from the VBAT voltage when the main
+ VDD supply is powered off.
+ To retain the content of the RTC backup registers, backup SRAM, and supply
+ the RTC when VDD is turned off, VBAT pin can be connected to an optional
+ standby voltage supplied by a battery or by another source.
+
+ [..] To allow the RTC operating even when the main digital supply (VDD) is turned
+ off, the VBAT pin powers the following blocks:
+ (#) The RTC
+ (#) The LSE oscillator
+ (#) The backup SRAM when the low power backup regulator is enabled
+ (#) PC13 to PC15 I/Os, plus PI8 I/O (when available)
+
+ [..] When the backup domain is supplied by VDD (analog switch connected to VDD),
+ the following pins are available:
+ (#) PC14 and PC15 can be used as either GPIO or LSE pins
+ (#) PC13 can be used as a GPIO or as the RTC_AF1 pin
+ (#) PI8 can be used as a GPIO or as the RTC_AF2 pin
+
+ [..] When the backup domain is supplied by VBAT (analog switch connected to VBAT
+ because VDD is not present), the following pins are available:
+ (#) PC14 and PC15 can be used as LSE pins only
+ (#) PC13 can be used as the RTC_AF1 pin
+ (#) PI8 can be used as the RTC_AF2 pin
+
+ ##### Backup Domain Reset #####
+ ==================================================================
+ [..] The backup domain reset sets all RTC registers and the RCC_BDCR register
+ to their reset values. The BKPSRAM is not affected by this reset. The only
+ way to reset the BKPSRAM is through the Flash interface by requesting
+ a protection level change from 1 to 0.
+ [..] A backup domain reset is generated when one of the following events occurs:
+ (#) Software reset, triggered by setting the BDRST bit in the
+ RCC Backup domain control register (RCC_BDCR).
+ (#) VDD or VBAT power on, if both supplies have previously been powered off.
+
+ ##### Backup Domain Access #####
+ ==================================================================
+ [..] After reset, the backup domain (RTC registers, RTC backup data
+ registers and backup SRAM) is protected against possible unwanted write
+ accesses.
+ [..] To enable access to the RTC Domain and RTC registers, proceed as follows:
+ (+) Enable the Power Controller (PWR) APB1 interface clock using the
+ __PWR_CLK_ENABLE() function.
+ (+) Enable access to RTC domain using the HAL_PWR_EnableBkUpAccess() function.
+ (+) Select the RTC clock source using the __HAL_RCC_RTC_CONFIG() function.
+ (+) Enable RTC Clock using the __HAL_RCC_RTC_ENABLE() function.
+
+
+ ##### How to use this driver #####
+ ==================================================================
+ [..]
+ (+) Enable the RTC domain access (see description in the section above).
+ (+) Configure the RTC Prescaler (Asynchronous and Synchronous) and RTC hour
+ format using the HAL_RTC_Init() function.
+
+ *** Time and Date configuration ***
+ ===================================
+ [..]
+ (+) To configure the RTC Calendar (Time and Date) use the HAL_RTC_SetTime()
+ and HAL_RTC_SetDate() functions.
+ (+) To read the RTC Calendar, use the HAL_RTC_GetTime() and HAL_RTC_GetDate() functions.
+
+ *** Alarm configuration ***
+ ===========================
+ [..]
+ (+) To configure the RTC Alarm use the HAL_RTC_SetAlarm() function.
+ You can also configure the RTC Alarm with interrupt mode using the HAL_RTC_SetAlarm_IT() function.
+ (+) To read the RTC Alarm, use the HAL_RTC_GetAlarm() function.
+
+ ##### RTC and low power modes #####
+ ==================================================================
+ [..] The MCU can be woken up from a low power mode by an RTC alternate
+ function.
+ [..] The RTC alternate functions are the RTC alarms (Alarm A and Alarm B),
+ RTC wakeup, RTC tamper event detection and RTC time stamp event detection.
+ These RTC alternate functions can wake up the system from the Stop and
+ Standby low power modes.
+ [..] The system can also wake up from low power modes without depending
+ on an external interrupt (Auto-wakeup mode), by using the RTC alarm
+ or the RTC wakeup events.
+ [..] The RTC provides a programmable time base for waking up from the
+ Stop or Standby mode at regular intervals.
+ Wakeup from STOP and STANDBY modes is possible only when the RTC clock source
+ is LSE or LSI.
+
+ @endverbatim
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f4xx_hal.h"
+
+/** @addtogroup STM32F4xx_HAL_Driver
+ * @{
+ */
+
+/** @defgroup RTC
+ * @brief RTC HAL module driver
+ * @{
+ */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup RTC_Private_Functions
+ * @{
+ */
+
+/** @defgroup RTC_Group1 Initialization and de-initialization functions
+ * @brief Initialization and Configuration functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Initialization and de-initialization functions #####
+ ===============================================================================
+ [..] This section provides functions allowing to initialize and configure the
+ RTC Prescaler (Synchronous and Asynchronous), RTC Hour format, disable
+ RTC registers Write protection, enter and exit the RTC initialization mode,
+ RTC registers synchronization check and reference clock detection enable.
+ (#) The RTC Prescaler is programmed to generate the RTC 1Hz time base.
+ It is split into 2 programmable prescalers to minimize power consumption.
+ (++) A 7-bit asynchronous prescaler and a 13-bit synchronous prescaler.
+ (++) When both prescalers are used, it is recommended to configure the
+ asynchronous prescaler to a high value to minimize power consumption.
+ (#) All RTC registers are Write protected. Writing to the RTC registers
+ is enabled by writing a key into the Write Protection register, RTC_WPR.
+ (#) To configure the RTC Calendar, user application should enter
+ initialization mode. In this mode, the calendar counter is stopped
+ and its value can be updated. When the initialization sequence is
+ complete, the calendar restarts counting after 4 RTCCLK cycles.
+ (#) To read the calendar through the shadow registers after Calendar
+ initialization, calendar update or after wakeup from low power modes
+ the software must first clear the RSF flag. The software must then
+ wait until it is set again before reading the calendar, which means
+ that the calendar registers have been correctly copied into the
+ RTC_TR and RTC_DR shadow registers.The HAL_RTC_WaitForSynchro() function
+ implements the above software sequence (RSF clear and RSF check).
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Initializes the RTC peripheral
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_Init(RTC_HandleTypeDef *hrtc)
+{
+ /* Check the RTC peripheral state */
+ if(hrtc == HAL_NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ /* Check the parameters */
+ assert_param(IS_RTC_HOUR_FORMAT(hrtc->Init.HourFormat));
+ assert_param(IS_RTC_ASYNCH_PREDIV(hrtc->Init.AsynchPrediv));
+ assert_param(IS_RTC_SYNCH_PREDIV(hrtc->Init.SynchPrediv));
+ assert_param (IS_RTC_OUTPUT(hrtc->Init.OutPut));
+ assert_param (IS_RTC_OUTPUT_POL(hrtc->Init.OutPutPolarity));
+ assert_param(IS_RTC_OUTPUT_TYPE(hrtc->Init.OutPutType));
+
+ if(hrtc->State == HAL_RTC_STATE_RESET)
+ {
+ /* Initialize RTC MSP */
+ HAL_RTC_MspInit(hrtc);
+ }
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ /* Set Initialization mode */
+ if(RTC_EnterInitMode(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ return HAL_ERROR;
+ }
+ else
+ {
+ /* Clear RTC_CR FMT, OSEL and POL Bits */
+ hrtc->Instance->CR &= ((uint32_t)~(RTC_CR_FMT | RTC_CR_OSEL | RTC_CR_POL));
+ /* Set RTC_CR register */
+ hrtc->Instance->CR |= (uint32_t)(hrtc->Init.HourFormat | hrtc->Init.OutPut | hrtc->Init.OutPutPolarity);
+
+ /* Configure the RTC PRER */
+ hrtc->Instance->PRER = (uint32_t)(hrtc->Init.SynchPrediv);
+ hrtc->Instance->PRER |= (uint32_t)(hrtc->Init.AsynchPrediv << 16);
+
+ /* Exit Initialization mode */
+ hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT;
+
+ hrtc->Instance->TAFCR &= (uint32_t)~RTC_TAFCR_ALARMOUTTYPE;
+ hrtc->Instance->TAFCR |= (uint32_t)(hrtc->Init.OutPutType);
+
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_READY;
+
+ return HAL_OK;
+ }
+}
+
+/**
+ * @brief DeInitializes the RTC peripheral
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @note This function doesn't reset the RTC Backup Data registers.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_DeInit(RTC_HandleTypeDef *hrtc)
+{
+ uint32_t tickstart = 0;
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ /* Set Initialization mode */
+ if(RTC_EnterInitMode(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ return HAL_ERROR;
+ }
+ else
+ {
+ /* Reset TR, DR and CR registers */
+ hrtc->Instance->TR = (uint32_t)0x00000000;
+ hrtc->Instance->DR = (uint32_t)0x00002101;
+ /* Reset All CR bits except CR[2:0] */
+ hrtc->Instance->CR &= (uint32_t)0x00000007;
+
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till WUTWF flag is set and if Time out is reached exit */
+ while(((hrtc->Instance->ISR) & RTC_ISR_WUTWF) == (uint32_t)RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Reset all RTC CR register bits */
+ hrtc->Instance->CR &= (uint32_t)0x00000000;
+ hrtc->Instance->WUTR = (uint32_t)0x0000FFFF;
+ hrtc->Instance->PRER = (uint32_t)0x007F00FF;
+ hrtc->Instance->CALIBR = (uint32_t)0x00000000;
+ hrtc->Instance->ALRMAR = (uint32_t)0x00000000;
+ hrtc->Instance->ALRMBR = (uint32_t)0x00000000;
+ hrtc->Instance->SHIFTR = (uint32_t)0x00000000;
+ hrtc->Instance->CALR = (uint32_t)0x00000000;
+ hrtc->Instance->ALRMASSR = (uint32_t)0x00000000;
+ hrtc->Instance->ALRMBSSR = (uint32_t)0x00000000;
+
+ /* Reset ISR register and exit initialization mode */
+ hrtc->Instance->ISR = (uint32_t)0x00000000;
+
+ /* Reset Tamper and alternate functions configuration register */
+ hrtc->Instance->TAFCR = 0x00000000;
+
+ /* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */
+ if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET)
+ {
+ if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ return HAL_ERROR;
+ }
+ }
+ }
+
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* De-Initialize RTC MSP */
+ HAL_RTC_MspDeInit(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_RESET;
+
+ /* Release Lock */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Initializes the RTC MSP.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @retval None
+ */
+__weak void HAL_RTC_MspInit(RTC_HandleTypeDef* hrtc)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_RTC_MspInit could be implenetd in the user file
+ */
+}
+
+/**
+ * @brief DeInitializes the RTC MSP.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @retval None
+ */
+__weak void HAL_RTC_MspDeInit(RTC_HandleTypeDef* hrtc)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_RTC_MspDeInit could be implenetd in the user file
+ */
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup RTC_Group2 RTC Time and Date functions
+ * @brief RTC Time and Date functions
+ *
+@verbatim
+ ===============================================================================
+ ##### RTC Time and Date functions #####
+ ===============================================================================
+
+ [..] This section provides functions allowing to configure Time and Date features
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Sets RTC current time.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @param sTime: Pointer to Time structure
+ * @param Format: Specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg FORMAT_BIN: Binary data format
+ * @arg FORMAT_BCD: BCD data format
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_SetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format)
+{
+ uint32_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+ assert_param(IS_RTC_DAYLIGHT_SAVING(sTime->DayLightSaving));
+ assert_param(IS_RTC_STORE_OPERATION(sTime->StoreOperation));
+
+ /* Process Locked */
+ __HAL_LOCK(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ if(Format == FORMAT_BIN)
+ {
+ if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET)
+ {
+ assert_param(IS_RTC_HOUR12(sTime->Hours));
+ assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat));
+ }
+ else
+ {
+ sTime->TimeFormat = 0x00;
+ assert_param(IS_RTC_HOUR24(sTime->Hours));
+ }
+ assert_param(IS_RTC_MINUTES(sTime->Minutes));
+ assert_param(IS_RTC_SECONDS(sTime->Seconds));
+
+ tmpreg = (uint32_t)(((uint32_t)RTC_ByteToBcd2(sTime->Hours) << 16) | \
+ ((uint32_t)RTC_ByteToBcd2(sTime->Minutes) << 8) | \
+ ((uint32_t)RTC_ByteToBcd2(sTime->Seconds)) | \
+ (((uint32_t)sTime->TimeFormat) << 16));
+ }
+ else
+ {
+ if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET)
+ {
+ tmpreg = RTC_Bcd2ToByte(sTime->Hours);
+ assert_param(IS_RTC_HOUR12(tmpreg));
+ assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat));
+ }
+ else
+ {
+ sTime->TimeFormat = 0x00;
+ assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sTime->Hours)));
+ }
+ assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sTime->Minutes)));
+ assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sTime->Seconds)));
+ tmpreg = (((uint32_t)(sTime->Hours) << 16) | \
+ ((uint32_t)(sTime->Minutes) << 8) | \
+ ((uint32_t)sTime->Seconds) | \
+ ((uint32_t)(sTime->TimeFormat) << 16));
+ }
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ /* Set Initialization mode */
+ if(RTC_EnterInitMode(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_ERROR;
+ }
+ else
+ {
+ /* Set the RTC_TR register */
+ hrtc->Instance->TR = (uint32_t)(tmpreg & RTC_TR_RESERVED_MASK);
+
+ /* Clear the bits to be configured */
+ hrtc->Instance->CR &= (uint32_t)~RTC_CR_BCK;
+
+ /* Configure the RTC_CR register */
+ hrtc->Instance->CR |= (uint32_t)(sTime->DayLightSaving | sTime->StoreOperation);
+
+ /* Exit Initialization mode */
+ hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT;
+
+ /* If CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */
+ if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET)
+ {
+ if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_ERROR;
+ }
+ }
+
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_READY;
+
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_OK;
+ }
+}
+
+/**
+ * @brief Gets RTC current time.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @param sTime: Pointer to Time structure
+ * @param Format: Specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg FORMAT_BIN: Binary data format
+ * @arg FORMAT_BCD: BCD data format
+ * @note Call HAL_RTC_GetDate() after HAL_RTC_GetTime() to unlock the values
+ * in the higher-order calendar shadow registers.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_GetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format)
+{
+ uint32_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+
+ /* Get subseconds values from the correspondent registers*/
+ sTime->SubSeconds = (uint32_t)(hrtc->Instance->SSR);
+
+ /* Get the TR register */
+ tmpreg = (uint32_t)(hrtc->Instance->TR & RTC_TR_RESERVED_MASK);
+
+ /* Fill the structure fields with the read parameters */
+ sTime->Hours = (uint8_t)((tmpreg & (RTC_TR_HT | RTC_TR_HU)) >> 16);
+ sTime->Minutes = (uint8_t)((tmpreg & (RTC_TR_MNT | RTC_TR_MNU)) >>8);
+ sTime->Seconds = (uint8_t)(tmpreg & (RTC_TR_ST | RTC_TR_SU));
+ sTime->TimeFormat = (uint8_t)((tmpreg & (RTC_TR_PM)) >> 16);
+
+ /* Check the input parameters format */
+ if(Format == FORMAT_BIN)
+ {
+ /* Convert the time structure parameters to Binary format */
+ sTime->Hours = (uint8_t)RTC_Bcd2ToByte(sTime->Hours);
+ sTime->Minutes = (uint8_t)RTC_Bcd2ToByte(sTime->Minutes);
+ sTime->Seconds = (uint8_t)RTC_Bcd2ToByte(sTime->Seconds);
+ }
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Sets RTC current date.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @param sDate: Pointer to date structure
+ * @param Format: specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg FORMAT_BIN: Binary data format
+ * @arg FORMAT_BCD: BCD data format
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_SetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format)
+{
+ uint32_t datetmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+
+ /* Process Locked */
+ __HAL_LOCK(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ if((Format == FORMAT_BIN) && ((sDate->Month & 0x10) == 0x10))
+ {
+ sDate->Month = (uint8_t)((sDate->Month & (uint8_t)~(0x10)) + (uint8_t)0x0A);
+ }
+
+ assert_param(IS_RTC_WEEKDAY(sDate->WeekDay));
+
+ if(Format == FORMAT_BIN)
+ {
+ assert_param(IS_RTC_YEAR(sDate->Year));
+ assert_param(IS_RTC_MONTH(sDate->Month));
+ assert_param(IS_RTC_DATE(sDate->Date));
+
+ datetmpreg = (((uint32_t)RTC_ByteToBcd2(sDate->Year) << 16) | \
+ ((uint32_t)RTC_ByteToBcd2(sDate->Month) << 8) | \
+ ((uint32_t)RTC_ByteToBcd2(sDate->Date)) | \
+ ((uint32_t)sDate->WeekDay << 13));
+ }
+ else
+ {
+ assert_param(IS_RTC_YEAR(RTC_Bcd2ToByte(sDate->Year)));
+ datetmpreg = RTC_Bcd2ToByte(sDate->Month);
+ assert_param(IS_RTC_MONTH(datetmpreg));
+ datetmpreg = RTC_Bcd2ToByte(sDate->Date);
+ assert_param(IS_RTC_DATE(datetmpreg));
+
+ datetmpreg = ((((uint32_t)sDate->Year) << 16) | \
+ (((uint32_t)sDate->Month) << 8) | \
+ ((uint32_t)sDate->Date) | \
+ (((uint32_t)sDate->WeekDay) << 13));
+ }
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ /* Set Initialization mode */
+ if(RTC_EnterInitMode(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Set RTC state*/
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_ERROR;
+ }
+ else
+ {
+ /* Set the RTC_DR register */
+ hrtc->Instance->DR = (uint32_t)(datetmpreg & RTC_DR_RESERVED_MASK);
+
+ /* Exit Initialization mode */
+ hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT;
+
+ /* If CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */
+ if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET)
+ {
+ if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_ERROR;
+ }
+ }
+
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_READY ;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_OK;
+ }
+}
+
+/**
+ * @brief Gets RTC current date.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @param sDate: Pointer to Date structure
+ * @param Format: Specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg FORMAT_BIN: Binary data format
+ * @arg FORMAT_BCD: BCD data format
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_GetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format)
+{
+ uint32_t datetmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+
+ /* Get the DR register */
+ datetmpreg = (uint32_t)(hrtc->Instance->DR & RTC_DR_RESERVED_MASK);
+
+ /* Fill the structure fields with the read parameters */
+ sDate->Year = (uint8_t)((datetmpreg & (RTC_DR_YT | RTC_DR_YU)) >> 16);
+ sDate->Month = (uint8_t)((datetmpreg & (RTC_DR_MT | RTC_DR_MU)) >> 8);
+ sDate->Date = (uint8_t)(datetmpreg & (RTC_DR_DT | RTC_DR_DU));
+ sDate->WeekDay = (uint8_t)((datetmpreg & (RTC_DR_WDU)) >> 13);
+
+ /* Check the input parameters format */
+ if(Format == FORMAT_BIN)
+ {
+ /* Convert the date structure parameters to Binary format */
+ sDate->Year = (uint8_t)RTC_Bcd2ToByte(sDate->Year);
+ sDate->Month = (uint8_t)RTC_Bcd2ToByte(sDate->Month);
+ sDate->Date = (uint8_t)RTC_Bcd2ToByte(sDate->Date);
+ }
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup RTC_Group3 RTC Alarm functions
+ * @brief RTC Alarm functions
+ *
+@verbatim
+ ===============================================================================
+ ##### RTC Alarm functions #####
+ ===============================================================================
+
+ [..] This section provides functions allowing to configure Alarm feature
+
+@endverbatim
+ * @{
+ */
+/**
+ * @brief Sets the specified RTC Alarm.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @param sAlarm: Pointer to Alarm structure
+ * @param Format: Specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg FORMAT_BIN: Binary data format
+ * @arg FORMAT_BCD: BCD data format
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_SetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format)
+{
+ uint32_t tickstart = 0;
+ uint32_t tmpreg = 0, subsecondtmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+ assert_param(IS_ALARM(sAlarm->Alarm));
+ assert_param(IS_ALARM_MASK(sAlarm->AlarmMask));
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(sAlarm->AlarmDateWeekDaySel));
+ assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(sAlarm->AlarmTime.SubSeconds));
+ assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(sAlarm->AlarmSubSecondMask));
+
+ /* Process Locked */
+ __HAL_LOCK(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ if(Format == FORMAT_BIN)
+ {
+ if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET)
+ {
+ assert_param(IS_RTC_HOUR12(sAlarm->AlarmTime.Hours));
+ assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
+ }
+ else
+ {
+ sAlarm->AlarmTime.TimeFormat = 0x00;
+ assert_param(IS_RTC_HOUR24(sAlarm->AlarmTime.Hours));
+ }
+ assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes));
+ assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds));
+
+ if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay));
+ }
+ else
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay));
+ }
+
+ tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << 16) | \
+ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << 8) | \
+ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds)) | \
+ ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16) | \
+ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmDateWeekDay) << 24) | \
+ ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \
+ ((uint32_t)sAlarm->AlarmMask));
+ }
+ else
+ {
+ if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET)
+ {
+ tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours);
+ assert_param(IS_RTC_HOUR12(tmpreg));
+ assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
+ }
+ else
+ {
+ sAlarm->AlarmTime.TimeFormat = 0x00;
+ assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
+ }
+
+ assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes)));
+ assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds)));
+
+ if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ {
+ tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay);
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(tmpreg));
+ }
+ else
+ {
+ tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay);
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(tmpreg));
+ }
+
+ tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << 16) | \
+ ((uint32_t)(sAlarm->AlarmTime.Minutes) << 8) | \
+ ((uint32_t) sAlarm->AlarmTime.Seconds) | \
+ ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16) | \
+ ((uint32_t)(sAlarm->AlarmDateWeekDay) << 24) | \
+ ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \
+ ((uint32_t)sAlarm->AlarmMask));
+ }
+
+ /* Configure the Alarm A or Alarm B Sub Second registers */
+ subsecondtmpreg = (uint32_t)((uint32_t)(sAlarm->AlarmTime.SubSeconds) | (uint32_t)(sAlarm->AlarmSubSecondMask));
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ /* Configure the Alarm register */
+ if(sAlarm->Alarm == RTC_ALARM_A)
+ {
+ /* Disable the Alarm A interrupt */
+ __HAL_RTC_ALARMA_DISABLE(hrtc);
+
+ /* In case of interrupt mode is used, the interrupt source must disabled */
+ __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRA);
+
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till RTC ALRAWF flag is set and if Time out is reached exit */
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+
+ hrtc->Instance->ALRMAR = (uint32_t)tmpreg;
+ /* Configure the Alarm A Sub Second register */
+ hrtc->Instance->ALRMASSR = subsecondtmpreg;
+ /* Configure the Alarm state: Enable Alarm */
+ __HAL_RTC_ALARMA_ENABLE(hrtc);
+ }
+ else
+ {
+ /* Disable the Alarm B interrupt */
+ __HAL_RTC_ALARMB_DISABLE(hrtc);
+
+ /* In case of interrupt mode is used, the interrupt source must disabled */
+ __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRB);
+
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till RTC ALRBWF flag is set and if Time out is reached exit */
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+
+ hrtc->Instance->ALRMBR = (uint32_t)tmpreg;
+ /* Configure the Alarm B Sub Second register */
+ hrtc->Instance->ALRMBSSR = subsecondtmpreg;
+ /* Configure the Alarm state: Enable Alarm */
+ __HAL_RTC_ALARMB_ENABLE(hrtc);
+ }
+
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Change RTC state */
+ hrtc->State = HAL_RTC_STATE_READY;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Sets the specified RTC Alarm with Interrupt
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @param sAlarm: Pointer to Alarm structure
+ * @param Format: Specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg FORMAT_BIN: Binary data format
+ * @arg FORMAT_BCD: BCD data format
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_SetAlarm_IT(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format)
+{
+ uint32_t tickstart = 0;
+ uint32_t tmpreg = 0, subsecondtmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+ assert_param(IS_ALARM(sAlarm->Alarm));
+ assert_param(IS_ALARM_MASK(sAlarm->AlarmMask));
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(sAlarm->AlarmDateWeekDaySel));
+ assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(sAlarm->AlarmTime.SubSeconds));
+ assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(sAlarm->AlarmSubSecondMask));
+
+ /* Process Locked */
+ __HAL_LOCK(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ if(Format == FORMAT_BIN)
+ {
+ if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET)
+ {
+ assert_param(IS_RTC_HOUR12(sAlarm->AlarmTime.Hours));
+ assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
+ }
+ else
+ {
+ sAlarm->AlarmTime.TimeFormat = 0x00;
+ assert_param(IS_RTC_HOUR24(sAlarm->AlarmTime.Hours));
+ }
+ assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes));
+ assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds));
+
+ if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay));
+ }
+ else
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay));
+ }
+ tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << 16) | \
+ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << 8) | \
+ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds)) | \
+ ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16) | \
+ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmDateWeekDay) << 24) | \
+ ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \
+ ((uint32_t)sAlarm->AlarmMask));
+ }
+ else
+ {
+ if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET)
+ {
+ tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours);
+ assert_param(IS_RTC_HOUR12(tmpreg));
+ assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
+ }
+ else
+ {
+ sAlarm->AlarmTime.TimeFormat = 0x00;
+ assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
+ }
+
+ assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes)));
+ assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds)));
+
+ if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ {
+ tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay);
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(tmpreg));
+ }
+ else
+ {
+ tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay);
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(tmpreg));
+ }
+ tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << 16) | \
+ ((uint32_t)(sAlarm->AlarmTime.Minutes) << 8) | \
+ ((uint32_t) sAlarm->AlarmTime.Seconds) | \
+ ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16) | \
+ ((uint32_t)(sAlarm->AlarmDateWeekDay) << 24) | \
+ ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \
+ ((uint32_t)sAlarm->AlarmMask));
+ }
+ /* Configure the Alarm A or Alarm B Sub Second registers */
+ subsecondtmpreg = (uint32_t)((uint32_t)(sAlarm->AlarmTime.SubSeconds) | (uint32_t)(sAlarm->AlarmSubSecondMask));
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ /* Configure the Alarm register */
+ if(sAlarm->Alarm == RTC_ALARM_A)
+ {
+ /* Disable the Alarm A interrupt */
+ __HAL_RTC_ALARMA_DISABLE(hrtc);
+
+ /* Clear flag alarm A */
+ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRAF);
+
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till RTC ALRAWF flag is set and if Time out is reached exit */
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+
+ hrtc->Instance->ALRMAR = (uint32_t)tmpreg;
+ /* Configure the Alarm A Sub Second register */
+ hrtc->Instance->ALRMASSR = subsecondtmpreg;
+ /* Configure the Alarm state: Enable Alarm */
+ __HAL_RTC_ALARMA_ENABLE(hrtc);
+ /* Configure the Alarm interrupt */
+ __HAL_RTC_ALARM_ENABLE_IT(hrtc,RTC_IT_ALRA);
+ }
+ else
+ {
+ /* Disable the Alarm B interrupt */
+ __HAL_RTC_ALARMB_DISABLE(hrtc);
+
+ /* Clear flag alarm B */
+ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRBF);
+
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till RTC ALRBWF flag is set and if Time out is reached exit */
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+
+ hrtc->Instance->ALRMBR = (uint32_t)tmpreg;
+ /* Configure the Alarm B Sub Second register */
+ hrtc->Instance->ALRMBSSR = subsecondtmpreg;
+ /* Configure the Alarm state: Enable Alarm */
+ __HAL_RTC_ALARMB_ENABLE(hrtc);
+ /* Configure the Alarm interrupt */
+ __HAL_RTC_ALARM_ENABLE_IT(hrtc, RTC_IT_ALRB);
+ }
+
+ /* RTC Alarm Interrupt Configuration: EXTI configuration */
+ __HAL_RTC_EXTI_ENABLE_IT(RTC_EXTI_LINE_ALARM_EVENT);
+
+ EXTI->RTSR |= RTC_EXTI_LINE_ALARM_EVENT;
+
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_READY;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Deactive the specified RTC Alarm
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @param Alarm: Specifies the Alarm.
+ * This parameter can be one of the following values:
+ * @arg RTC_ALARM_A: AlarmA
+ * @arg RTC_ALARM_B: AlarmB
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_DeactivateAlarm(RTC_HandleTypeDef *hrtc, uint32_t Alarm)
+{
+ uint32_t tickstart = 0;
+
+ /* Check the parameters */
+ assert_param(IS_ALARM(Alarm));
+
+ /* Process Locked */
+ __HAL_LOCK(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ if(Alarm == RTC_ALARM_A)
+ {
+ /* AlarmA */
+ __HAL_RTC_ALARMA_DISABLE(hrtc);
+
+ /* In case of interrupt mode is used, the interrupt source must disabled */
+ __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRA);
+
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till RTC ALRxWF flag is set and if Time out is reached exit */
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else
+ {
+ /* AlarmB */
+ __HAL_RTC_ALARMB_DISABLE(hrtc);
+
+ /* In case of interrupt mode is used, the interrupt source must disabled */
+ __HAL_RTC_ALARM_DISABLE_IT(hrtc,RTC_IT_ALRB);
+
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till RTC ALRxWF flag is set and if Time out is reached exit */
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_READY;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Gets the RTC Alarm value and masks.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @param sAlarm: Pointer to Date structure
+ * @param Alarm: Specifies the Alarm.
+ * This parameter can be one of the following values:
+ * @arg RTC_ALARM_A: AlarmA
+ * @arg RTC_ALARM_B: AlarmB
+ * @param Format: Specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg FORMAT_BIN: Binary data format
+ * @arg FORMAT_BCD: BCD data format
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_GetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Alarm, uint32_t Format)
+{
+ uint32_t tmpreg = 0, subsecondtmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+ assert_param(IS_ALARM(Alarm));
+
+ if(Alarm == RTC_ALARM_A)
+ {
+ /* AlarmA */
+ sAlarm->Alarm = RTC_ALARM_A;
+
+ tmpreg = (uint32_t)(hrtc->Instance->ALRMAR);
+ subsecondtmpreg = (uint32_t)((hrtc->Instance->ALRMASSR ) & RTC_ALRMASSR_SS);
+ }
+ else
+ {
+ sAlarm->Alarm = RTC_ALARM_B;
+
+ tmpreg = (uint32_t)(hrtc->Instance->ALRMBR);
+ subsecondtmpreg = (uint32_t)((hrtc->Instance->ALRMBSSR) & RTC_ALRMBSSR_SS);
+ }
+
+ /* Fill the structure with the read parameters */
+ sAlarm->AlarmTime.Hours = (uint32_t)((tmpreg & (RTC_ALRMAR_HT | RTC_ALRMAR_HU)) >> 16);
+ sAlarm->AlarmTime.Minutes = (uint32_t)((tmpreg & (RTC_ALRMAR_MNT | RTC_ALRMAR_MNU)) >> 8);
+ sAlarm->AlarmTime.Seconds = (uint32_t)(tmpreg & (RTC_ALRMAR_ST | RTC_ALRMAR_SU));
+ sAlarm->AlarmTime.TimeFormat = (uint32_t)((tmpreg & RTC_ALRMAR_PM) >> 16);
+ sAlarm->AlarmTime.SubSeconds = (uint32_t) subsecondtmpreg;
+ sAlarm->AlarmDateWeekDay = (uint32_t)((tmpreg & (RTC_ALRMAR_DT | RTC_ALRMAR_DU)) >> 24);
+ sAlarm->AlarmDateWeekDaySel = (uint32_t)(tmpreg & RTC_ALRMAR_WDSEL);
+ sAlarm->AlarmMask = (uint32_t)(tmpreg & RTC_ALARMMASK_ALL);
+
+ if(Format == FORMAT_BIN)
+ {
+ sAlarm->AlarmTime.Hours = RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours);
+ sAlarm->AlarmTime.Minutes = RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes);
+ sAlarm->AlarmTime.Seconds = RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds);
+ sAlarm->AlarmDateWeekDay = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay);
+ }
+
+ return HAL_OK;
+}
+
+/**
+ * @brief This function handles Alarm interrupt request.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @retval None
+ */
+void HAL_RTC_AlarmIRQHandler(RTC_HandleTypeDef* hrtc)
+{
+ if(__HAL_RTC_ALARM_GET_IT(hrtc, RTC_IT_ALRA))
+ {
+ /* Get the status of the Interrupt */
+ if((uint32_t)(hrtc->Instance->CR & RTC_IT_ALRA) != (uint32_t)RESET)
+ {
+ /* AlarmA callback */
+ HAL_RTC_AlarmAEventCallback(hrtc);
+
+ /* Clear the Alarm interrupt pending bit */
+ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc,RTC_FLAG_ALRAF);
+ }
+ }
+
+ if(__HAL_RTC_ALARM_GET_IT(hrtc, RTC_IT_ALRB))
+ {
+ /* Get the status of the Interrupt */
+ if((uint32_t)(hrtc->Instance->CR & RTC_IT_ALRB) != (uint32_t)RESET)
+ {
+ /* AlarmB callback */
+ HAL_RTCEx_AlarmBEventCallback(hrtc);
+
+ /* Clear the Alarm interrupt pending bit */
+ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc,RTC_FLAG_ALRBF);
+ }
+ }
+
+ /* Clear the EXTI's line Flag for RTC Alarm */
+ __HAL_RTC_EXTI_CLEAR_FLAG(RTC_EXTI_LINE_ALARM_EVENT);
+
+ /* Change RTC state */
+ hrtc->State = HAL_RTC_STATE_READY;
+}
+
+/**
+ * @brief Alarm A callback.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @retval None
+ */
+__weak void HAL_RTC_AlarmAEventCallback(RTC_HandleTypeDef *hrtc)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_RTC_AlarmAEventCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief This function handles AlarmA Polling request.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @param Timeout: Timeout duration
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_PollForAlarmAEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout)
+{
+ uint32_t tickstart = 0;
+
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAF) == RESET)
+ {
+ if(Timeout != HAL_MAX_DELAY)
+ {
+ if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout))
+ {
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+
+ /* Clear the Alarm interrupt pending bit */
+ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRAF);
+
+ /* Change RTC state */
+ hrtc->State = HAL_RTC_STATE_READY;
+
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup RTC_Group4 Peripheral Control functions
+ * @brief Peripheral Control functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Peripheral Control functions #####
+ ===============================================================================
+ [..]
+ This subsection provides functions allowing to
+ (+) Wait for RTC Time and Date Synchronization
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Waits until the RTC Time and Date registers (RTC_TR and RTC_DR) are
+ * synchronized with RTC APB clock.
+ * @note The RTC Resynchronization mode is write protected, use the
+ * __HAL_RTC_WRITEPROTECTION_DISABLE() before calling this function.
+ * @note To read the calendar through the shadow registers after Calendar
+ * initialization, calendar update or after wakeup from low power modes
+ * the software must first clear the RSF flag.
+ * The software must then wait until it is set again before reading
+ * the calendar, which means that the calendar registers have been
+ * correctly copied into the RTC_TR and RTC_DR shadow registers.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_WaitForSynchro(RTC_HandleTypeDef* hrtc)
+{
+ uint32_t tickstart = 0;
+
+ /* Clear RSF flag */
+ hrtc->Instance->ISR &= (uint32_t)RTC_RSF_MASK;
+
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait the registers to be synchronised */
+ while((hrtc->Instance->ISR & RTC_ISR_RSF) == (uint32_t)RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ return HAL_OK;
+}
+
+/** @defgroup RTC_Group5 Peripheral State functions
+ * @brief Peripheral State functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Peripheral State functions #####
+ ===============================================================================
+ [..]
+ This subsection provides functions allowing to
+ (+) Get RTC state
+
+@endverbatim
+ * @{
+ */
+/**
+ * @brief Returns the RTC state.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @retval HAL state
+ */
+HAL_RTCStateTypeDef HAL_RTC_GetState(RTC_HandleTypeDef* hrtc)
+{
+ return hrtc->State;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @brief Enters the RTC Initialization mode.
+ * @note The RTC Initialization mode is write protected, use the
+ * __HAL_RTC_WRITEPROTECTION_DISABLE() before calling this function.
+ * @param hrtc: pointer to a RTC_HandleTypeDef structure that contains
+ * the configuration information for RTC.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef RTC_EnterInitMode(RTC_HandleTypeDef* hrtc)
+{
+ uint32_t tickstart = 0;
+
+ /* Check if the Initialization mode is set */
+ if((hrtc->Instance->ISR & RTC_ISR_INITF) == (uint32_t)RESET)
+ {
+ /* Set the Initialization mode */
+ hrtc->Instance->ISR = (uint32_t)RTC_INIT_MASK;
+
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till RTC is in INIT state and if Time out is reached exit */
+ while((hrtc->Instance->ISR & RTC_ISR_INITF) == (uint32_t)RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+
+ return HAL_OK;
+}
+
+
+/**
+ * @brief Converts a 2 digit decimal to BCD format.
+ * @param Value: Byte to be converted
+ * @retval Converted byte
+ */
+uint8_t RTC_ByteToBcd2(uint8_t Value)
+{
+ uint32_t bcdhigh = 0;
+
+ while(Value >= 10)
+ {
+ bcdhigh++;
+ Value -= 10;
+ }
+
+ return ((uint8_t)(bcdhigh << 4) | Value);
+}
+
+/**
+ * @brief Converts from 2 digit BCD to Binary.
+ * @param Value: BCD value to be converted
+ * @retval Converted word
+ */
+uint8_t RTC_Bcd2ToByte(uint8_t Value)
+{
+ uint32_t tmp = 0;
+ tmp = ((uint8_t)(Value & (uint8_t)0xF0) >> (uint8_t)0x4) * 10;
+ return (tmp + (Value & (uint8_t)0x0F));
+}
+
+/**
+ * @}
+ */
+
+#endif /* HAL_RTC_MODULE_ENABLED */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
projects / qmk_firmware.git / blobdiff