+++ /dev/null
-/**
- ******************************************************************************
- * @file stm32f30x_hrtim.c
- * @author MCD Application Team
- * @version V1.1.0
- * @date 27-February-2014
- * @brief HRTIMx module driver.
- *
- * This file provides firmware functions to manage the following
- * functionalities of the HRTIMx peripheral:
- * + Initialization/de-initialization methods
- * + I/O operation methods
- * + Peripheral Control methods
- *
- @verbatim
-================================================================================
- ##### <HRTIM specific features> #####
-================================================================================
-
- [..] < HRTIM introduction:
- (#) The high-resolution timer can generate up to 10 digital signals with
- highly accurate timings.
- It is primarily intended to drive power conversion systems such as
- switch mode power supplies or lighting systems,
- but can be of general purpose usage, whenever a very fine timing
- resolution is expected.
-
- (#) Its modular architecture allows to generate either independent or
- coupled waveforms.
- The wave-shape is defined by self-contained timings
- (using counters and compare units) and a broad range of external events,
- such as analog or digital feedbacks and synchronisation signals.
- This allows to produce a large variety of control signal (PWM, phase-shifted,
- constant Ton,...) and address most of conversion topologies.
-
- (#) For control and monitoring purposes, the timer has also timing measure
- capabilities and links to built-in ADC and DAC converters.
- Last, it features light-load management mode and is able to handle
- various fault schemes for safe shut-down purposes.
-
-
- ##### How to use this driver #####
-================================================================================
- [..] This driver provides functions to configure and program the HRTIM
- of all stm32f33x devices.
- These functions are split in 9 groups:
-
- (#) HRTIM Simple TimeBase management: this group includes all needed functions
- to configure the HRTIM Timebase unit:
- (++) Initializes the HRTIMx timer in simple time base mode
- (++) Start/Stop the time base generation
- (++) Deinitialize the HRTIM peripheral
-
-
- (#) HRTIM simple Output Compare management: this group includes all needed
- functions to configure the Compare unit used in Output compare mode:
- (++) Initializes the HRTIMx timer time base unit
- (++) Configure the compare unit in in simple Output Compare mode
- (++) Start/Stop the Output compare generation
-
- (#) HRTIM simple PWM management: this group includes all needed
- functions to configure the Compare unit used in PWM mode:
- (++) Initializes the HRTIMx timer time base unit
- (++) Configure the compare unit in in simple PWM mode
- (++) Start/Stop the PWM generation
-
- (#) HRTIM simple Capture management: this group includes all needed
- functions to configure the Capture unit used in Capture mode:
- (++) Initializes the HRTIMx timer time base unit
- (++) Configure the compare unit in in simple Capture mode
- (++) Start/Stop the Capture mode
-
- (#) HRTIM simple One Pulse management: this group includes all needed
- functions to configure the Capture unit and Compare unit used in One Pulse mode:
- (++) Initializes the HRTIMx timer time base unit
- (++) Configure the compare unit and the capture unit in in simple One Pulse mode
- (++) Start/Stop the One Pulse mode generation
-
- (#) HRTIM Waveform management: this group includes all needed
- functions to configure the HRTIM possible waveform mode:
- (++) Initializes the HRTIMx timer Master time base unit
- (++) Initializes the HRTIMx timer Slaves time base unit
- (++) Configures the HRTIMx timer Compare unit
- (++) Configures the HRTIMx Slave timer Capture unit
- (++) Configures the HRTIMx timer Output unit
- (++) Configures the HRTIMx timer DeadTime / Chopper / Burst features
- (++) Configures the HRTIMx timer Fault / External event features
- (++) Configures the HRTIMx timer Synchronization features: Internal/External connection, DACs,...
- (++) Configures the HRTIMx timer Synchronization features: ADCs Triggers
- (++) HRTIMx timer Outputs Start/Stop
- (++) Start/Stop the HRTIMx Timer counters
-
- (#) HRTIM interrupts, DMA and flags management
- (++) Enable/Disable interrupt sources
- (++) Get flags status
- (++) Clear flags/ Pending bits
- (++) Enable/Disable DMA requests
- (++) Configure DMA burst mode
-
- (#) TIM specific interface management, this group includes all
- needed functions to use the specific TIM interface:
- (++) HRTIMx timer DLL calibration
-
- @endverbatim
- ******************************************************************************
- * @attention
- *
- * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-/* Includes ------------------------------------------------------------------*/
-#include "stm32f30x_hrtim.h"
-
-/** @addtogroup STM32F30x_StdPeriph_Driver
- * @{
- */
-
-/** @defgroup HRTIM
- * @brief HRTIM driver module
- * @{
- */
-
-/* Private typedef -----------------------------------------------------------*/
-/* Private define ------------------------------------------------------------*/
-#define HRTIM_FLTR_FLTxEN (HRTIM_FLTR_FLT1EN |\
- HRTIM_FLTR_FLT2EN |\
- HRTIM_FLTR_FLT3EN |\
- HRTIM_FLTR_FLT4EN | \
- HRTIM_FLTR_FLT5EN)
-
-#define HRTIM_TIMCR_TIMUPDATETRIGGER (HRTIM_TIMUPDATETRIGGER_MASTER |\
- HRTIM_TIMUPDATETRIGGER_TIMER_A |\
- HRTIM_TIMUPDATETRIGGER_TIMER_B |\
- HRTIM_TIMUPDATETRIGGER_TIMER_C |\
- HRTIM_TIMUPDATETRIGGER_TIMER_D |\
- HRTIM_TIMUPDATETRIGGER_TIMER_E)
-
-#define HRTIM_TIM_OFFSET (uint32_t)0x00000080
-/* Private macro -------------------------------------------------------------*/
-/* Private variables ---------------------------------------------------------*/
-static uint32_t TimerIdxToTimerId[] =
-{
- HRTIM_TIMERID_TIMER_A,
- HRTIM_TIMERID_TIMER_B,
- HRTIM_TIMERID_TIMER_C,
- HRTIM_TIMERID_TIMER_D,
- HRTIM_TIMERID_TIMER_E,
- HRTIM_TIMERID_MASTER,
-};
-
-/* Private function prototypes -----------------------------------------------*/
-/* Private functions ---------------------------------------------------------*/
-static void HRTIM_MasterBase_Config(HRTIM_TypeDef* HRTIMx, HRTIM_BaseInitTypeDef* HRTIM_BaseInitStruc);
-static void HRTIM_TimingUnitBase_Config(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx, HRTIM_BaseInitTypeDef* HRTIM_BaseInitStruct);
-static void HRTIM_MasterWaveform_Config(HRTIM_TypeDef * HRTIMx, HRTIM_TimerInitTypeDef * TimerInit);
-static void HRTIM_TimingUnitWaveform_Config(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- HRTIM_TimerInitTypeDef * TimerInit);
-static void HRTIM_CompareUnitConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t CompareUnit,
- HRTIM_CompareCfgTypeDef * CompareCfg);
-static void HRTIM_CaptureUnitConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t CaptureUnit,
- uint32_t Event);
-static void HRTIM_OutputConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t Output,
- HRTIM_OutputCfgTypeDef * OutputCfg);
-static void HRTIM_ExternalEventConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t Event,
- HRTIM_EventCfgTypeDef * EventCfg);
-static void HRTIM_TIM_ResetConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t Event);
- /** @defgroup HRTIM_Private_Functions
- * @{
- */
-
-/** @defgroup HRTIM_Group1 Initialization/de-initialization methods
- * @brief Initialization and Configuration functions
- *
-@verbatim
- ===============================================================================
- ##### Initialization/de-initialization methods #####
- ===============================================================================
- [..] This section provides functions allowing to:
- (+)Initializes timer in basic time base mode
- (+)Initializes timer in basic OC mode
- (+)Initializes timer in basic PWM mode
- (+)Initializes timer in basic Capture mode
- (+)Initializes timer in One Pulse mode
- (+)Initializes a timer operating in waveform mode
- (+)De-initializes the HRTIMx timer
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Initializes the HRTIMx timer in basic time base mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 for master timer
- * @arg 0x1 to 0x5 for timers A to E
- * @note The time-base unit initialization parameters specify:
- * The timer counter operating mode (continuous, one shot)
- * The timer clock prescaler
- * The timer period
- * The timer repetition counter.
- * @retval None
- */
-void HRTIM_SimpleBase_Init(HRTIM_TypeDef* HRTIMx, uint32_t TimerIdx, HRTIM_BaseInitTypeDef* HRTIM_BaseInitStruct)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMERINDEX(TimerIdx));
- assert_param(IS_HRTIM_MODE(HRTIM_BaseInitStruct->Mode));
-
- if (TimerIdx == HRTIM_TIMERINDEX_MASTER)
- {
- /* Configure master timer */
- HRTIM_MasterBase_Config(HRTIMx, HRTIM_BaseInitStruct);
- }
- else
- {
- /* Configure timing unit */
- HRTIM_TimingUnitBase_Config(HRTIMx, TimerIdx, HRTIM_BaseInitStruct);
- }
-}
-
-/**
- * @brief De-initializes a timer operating in all mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @retval None
- */
-void HRTIM_DeInit(HRTIM_TypeDef* HRTIMx)
-{
- /* Check the parameters */
- RCC_APB2PeriphResetCmd(RCC_APB2Periph_HRTIM1, ENABLE);
- RCC_APB2PeriphResetCmd(RCC_APB2Periph_HRTIM1, DISABLE);
- }
-
-/**
- * @brief Initializes the HRTIMx timer in basic output compare mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x1 to 0x5 for timers A to E
- * @note Initializes the time-base unit of the timer and prepare it to
- * operate in output compare mode
- * @retval None
- */
-void HRTIM_SimpleOC_Init(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx, HRTIM_BaseInitTypeDef* HRTIM_BaseInitStruct)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMERINDEX(TimerIdx));
- assert_param(IS_HRTIM_MODE(HRTIM_BaseInitStruct->Mode));
-
- /* Configure timing unit */
- HRTIM_TimingUnitBase_Config(HRTIMx, TimerIdx, HRTIM_BaseInitStruct);
-}
-
-/**
- * @brief Initializes the HRTIMx timer in basic PWM mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x1 to 0x5 for timers A to E
- * @note Initializes the time-base unit of the timer and prepare it to
- * operate in capture mode
- * @retval None
- */
-void HRTIM_SimplePWM_Init(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx, HRTIM_BaseInitTypeDef* HRTIM_BaseInitStruct)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMERINDEX(TimerIdx));
- assert_param(IS_HRTIM_MODE(HRTIM_BaseInitStruct->Mode));
-
- /* Configure timing unit */
- HRTIM_TimingUnitBase_Config(HRTIMx, TimerIdx, HRTIM_BaseInitStruct);
-}
-
-/**
- * @brief Initializes a timer operating in basic capture mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x1 to 0x5 for timers A to E
- * @retval None
- */
-void HRTIM_SimpleCapture_Init(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx, HRTIM_BaseInitTypeDef* HRTIM_BaseInitStruct)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMERINDEX(TimerIdx));
- assert_param(IS_HRTIM_MODE(HRTIM_BaseInitStruct->Mode));
-
- /* Configure timing unit */
- HRTIM_TimingUnitBase_Config(HRTIMx, TimerIdx, HRTIM_BaseInitStruct);
-}
-
-/**
- * @brief Initializes the HRTIMx timer in basic one pulse mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x1 to 0x5 for timers A to E
- * @note Initializes the time-base unit of the timer and prepare it to
- * operate in one pulse mode. In this mode the counter operates
- * in single shot mode (retriggerable or not)
- * @retval None
- */
-void HRTIM_SimpleOnePulse_Init(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx, HRTIM_BaseInitTypeDef* HRTIM_BaseInitStruct)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMERINDEX(TimerIdx));
- assert_param(IS_HRTIM_MODE(HRTIM_BaseInitStruct->Mode));
-
- /* Configure timing unit */
- HRTIM_TimingUnitBase_Config(HRTIMx, TimerIdx, HRTIM_BaseInitStruct);
-}
-
-/**
- * @brief Initializes a timer operating in waveform mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 for master timer
- * @arg 0x1 to 0x5 for timers A to E
- * @param pTimerInit: pointer to the timer initialization data structure
- * @retval None
- */
-void HRTIM_Waveform_Init(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- HRTIM_BaseInitTypeDef* HRTIM_BaseInitStruct,
- HRTIM_TimerInitTypeDef* HRTIM_TimerInitStruct)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_HALFMODE(HRTIM_TimerInitStruct->HalfModeEnable));
- assert_param(IS_HRTIM_SYNCSTART(HRTIM_TimerInitStruct->StartOnSync));
- assert_param(IS_HRTIM_SYNCRESET(HRTIM_TimerInitStruct->ResetOnSync));
- assert_param(IS_HRTIM_DACSYNC(HRTIM_TimerInitStruct->DACSynchro));
- assert_param(IS_HRTIM_PRELOAD(HRTIM_TimerInitStruct->PreloadEnable));
- assert_param(IS_HRTIM_TIMERBURSTMODE(HRTIM_TimerInitStruct->BurstMode));
- assert_param(IS_HRTIM_UPDATEONREPETITION(HRTIM_TimerInitStruct->RepetitionUpdate));
-
- if (TimerIdx == HRTIM_TIMERINDEX_MASTER)
- {
- /* Check parameters */
- assert_param(IS_HRTIM_UPDATEGATING_MASTER(HRTIM_TimerInitStruct->UpdateGating));
-
- /* Configure master timer */
- HRTIM_MasterBase_Config(HRTIMx, HRTIM_BaseInitStruct);
- HRTIM_MasterWaveform_Config(HRTIMx, HRTIM_TimerInitStruct);
- }
- else
- {
- /* Check parameters */
- assert_param(IS_HRTIM_UPDATEGATING_TIM(HRTIM_TimerInitStruct->UpdateGating));
-
- /* Configure timing unit */
- HRTIM_TimingUnitBase_Config(HRTIMx, TimerIdx, HRTIM_BaseInitStruct);
- HRTIM_TimingUnitWaveform_Config(HRTIMx, TimerIdx, HRTIM_TimerInitStruct);
- }
-}
-
-/**
- * @}
- */
-
-/** @defgroup HRTIM_Group2 I/O operation methods
- * @brief Data transfers functions
- *
-@verbatim
- ===============================================================================
- ##### IO operation methods #####
- ===============================================================================
- [..]
- This subsection provides a set of functions allowing to manage the HRTIMx data
- transfers.
- (+) Starts the DLL calibration.
- (+) Starts / stops the counter of a timer operating in basic time base mode
- (+) Starts / stops the output compare signal generation on the designed timer output
- (+) Starts / stops the PWM output signal generation on the designed timer output
- (+) Enables / disables a basic capture on the designed capture unit
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Starts the DLL calibration
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param CalibrationRate: DLL calibration period
- * This parameter can be one of the following values:
- * @arg HRTIM_CALIBRATIONRATE_7300: 7.3 ms
- * @arg HRTIM_CALIBRATIONRATE_910: 910 us
- * @arg HRTIM_CALIBRATIONRATE_114: 114 us
- * @arg HRTIM_CALIBRATIONRATE_14: 14 us
- * @retval None
- */
-void HRTIM_DLLCalibrationStart(HRTIM_TypeDef * HRTIMx, uint32_t CalibrationRate)
-{
- uint32_t HRTIM_dllcr;
-
- /* Check the parameters */
- assert_param(IS_HRTIM_CALIBRATIONRATE(CalibrationRate));
-
- /* Configure DLL Calibration */
- HRTIM_dllcr = (HRTIMx->HRTIM_COMMON).DLLCR;
-
- /* Set the Calibration rate */
- HRTIM_dllcr &= ~(HRTIM_DLLCR_CALRTE);
- HRTIM_dllcr |= CalibrationRate;
-
- /* Start DLL calibration */
- HRTIM_dllcr |= HRTIM_DLLCR_CAL;
-
- /* Update HRTIMx register */
- (HRTIMx->HRTIM_COMMON).DLLCR = HRTIM_dllcr;
-
-}
-/**
- * @brief Starts the counter of a timer operating in basic time base mode
- * @param HRTIMx: pointer to HRTIM peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x5 for master timer
- * @arg 0x0 to 0x4 for timers A to E
- * @retval None
- */
-void HRTIM_SimpleBaseStart(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMERINDEX(TimerIdx));
-
- /* Enable the timer counter */
- __HRTIM_ENABLE(HRTIMx, TimerIdxToTimerId[TimerIdx]);
-}
-
-/**
- * @brief Stops the counter of a timer operating in basic time base mode
- * @param HRTIMx: pointer to HRTIM peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x5 for master timer
- * @arg 0x0 to 0x4 for timers A to E
- * @retval None
- */
-void HRTIM_SimpleBaseStop(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMERINDEX(TimerIdx));
-
- /* Disable the timer counter */
- __HRTIM_DISABLE(HRTIMx, TimerIdxToTimerId[TimerIdx]);
-}
-
-/**
- * @brief Starts the output compare signal generation on the designed timer output
- * @param HRTIMx: pointer to HRTIM peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param OCChannel: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @retval None
- */
-void HRTIM_SimpleOCStart(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t OCChannel)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, OCChannel));
-
- /* Enable the timer output */
- (HRTIMx->HRTIM_COMMON).OENR |= OCChannel;
-
- /* Enable the timer counter */
- __HRTIM_ENABLE(HRTIMx, TimerIdxToTimerId[TimerIdx]);
-
-}
-
-/**
- * @brief Stops the output compare signal generation on the designed timer output
- * @param HRTIMx: pointer to HRTIM peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param OCChannel: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @retval None
- */
-void HRTIM_SimpleOCStop(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t OCChannel)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, OCChannel));
-
- /* Disable the timer output */
- HRTIMx->HRTIM_COMMON.DISR |= OCChannel;
-
- /* Disable the timer counter */
- __HRTIM_DISABLE(HRTIMx, TimerIdxToTimerId[TimerIdx]);
-}
-
-/**
- * @brief Starts the PWM output signal generation on the designed timer output
- * @param HRTIMx: pointer to HRTIM peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param PWMChannel: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @retval None
- */
-void HRTIM_SimplePWMStart(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t PWMChannel)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, PWMChannel));
-
- /* Enable the timer output */
- HRTIMx->HRTIM_COMMON.OENR |= PWMChannel;
-
- /* Enable the timer counter */
- __HRTIM_ENABLE(HRTIMx, TimerIdxToTimerId[TimerIdx]);
-}
-
-/**
- * @brief Stops the PWM output signal generation on the designed timer output
- * @param HRTIMx: pointer to HRTIM peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param PWMChannel: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @retval None
- */
-void HRTIM_SimplePWMStop(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t PWMChannel)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, PWMChannel));
-
- /* Disable the timer output */
- HRTIMx->HRTIM_COMMON.DISR |= PWMChannel;
-
- /* Disable the timer counter */
- __HRTIM_DISABLE(HRTIMx, TimerIdxToTimerId[TimerIdx]);
-}
-
-/**
- * @brief Enables a basic capture on the designed capture unit
- * @param HRTIMx: pointer to HRTIM peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param CaptureChannel: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_CAPTUREUNIT_1: Capture unit 1
- * @arg HRTIM_CAPTUREUNIT_2: Capture unit 2
- * @retval None
- * @note The external event triggering the capture is available for all timing
- * units. It can be used directly and is active as soon as the timing
- * unit counter is enabled.
- */
-void HRTIM_SimpleCaptureStart(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t CaptureChannel)
-{
- /* Enable the timer counter */
- __HRTIM_ENABLE(HRTIMx, TimerIdxToTimerId[TimerIdx]);
-
-}
-
-/**
- * @brief Disables a basic capture on the designed capture unit
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param CaptureChannel: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_CAPTUREUNIT_1: Capture unit 1
- * @arg HRTIM_CAPTUREUNIT_2: Capture unit 2
- * @retval None
- */
-void HRTIM_SimpleCaptureStop(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t CaptureChannel)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMING_UNIT(TimerIdx));
- assert_param(IS_HRTIM_CAPTUREUNIT(CaptureChannel));
-
- /* Set the capture unit trigger */
- switch (CaptureChannel)
- {
- case HRTIM_CAPTUREUNIT_1:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CPT1xCR = HRTIM_CAPTURETRIGGER_NONE;
- }
- break;
- case HRTIM_CAPTUREUNIT_2:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CPT2xCR = HRTIM_CAPTURETRIGGER_NONE;
- }
- break;
- default:
- break;
- }
-
- /* Disable the timer counter */
- if ((HRTIMx->HRTIM_TIMERx[TimerIdx].CPT1xCR == HRTIM_CAPTURETRIGGER_NONE) &&
- (HRTIMx->HRTIM_TIMERx[TimerIdx].CPT2xCR == HRTIM_CAPTURETRIGGER_NONE))
- {
- __HRTIM_DISABLE(HRTIMx, TimerIdxToTimerId[TimerIdx]);
- }
-
-}
-
-/**
- * @brief Enables the basic one pulse signal generation on the designed output
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param OnePulseChannel: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @retval None
- */
-void HRTIM_SimpleOnePulseStart(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t OnePulseChannel)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, OnePulseChannel));
-
- /* Enable the timer output */
- HRTIMx->HRTIM_COMMON.OENR |= OnePulseChannel;
-
- /* Enable the timer counter */
- __HRTIM_ENABLE(HRTIMx, TimerIdxToTimerId[TimerIdx]);
-}
-
-/**
- * @brief Disables the basic one pulse signal generation on the designed output
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param OnePulseChannel: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @retval None
- */
-void HRTIM_SimpleOnePulseStop(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t OnePulseChannel)
-{
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, OnePulseChannel));
-
- /* Disable the timer output */
- HRTIMx->HRTIM_COMMON.DISR |= OnePulseChannel;
-
- /* Disable the timer counter */
- __HRTIM_DISABLE(HRTIMx, TimerIdxToTimerId[TimerIdx]);
-}
-
-/**
- * @brief Starts the counter of the designated timer(s) operating in waveform mode
- * Timers can be combined (ORed) to allow for simultaneous counter start
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimersToStart: Timer counter(s) to start
- * This parameter can be any combination of the following values:
- * @arg HRTIM_TIMERID_MASTER
- * @arg HRTIM_TIMERID_TIMER_A
- * @arg HRTIM_TIMERID_TIMER_B
- * @arg HRTIM_TIMERID_TIMER_C
- * @arg HRTIM_TIMERID_TIMER_D
- * @arg HRTIM_TIMERID_TIMER_E
- * @retval None
- */
-void HRTIM_WaveformCounterStart(HRTIM_TypeDef * HRTIMx,
- uint32_t TimersToStart)
-{
- /* Enable timer(s) counter */
- HRTIMx->HRTIM_MASTER.MCR |= TimersToStart;
-}
-
-/**
- * @brief Stops the counter of the designated timer(s) operating in waveform mode
- * Timers can be combined (ORed) to allow for simultaneous counter stop
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimersToStop: Timer counter(s) to stop
- * This parameter can be any combination of the following values:
- * @arg HRTIM_TIMER_MASTER
- * @arg HRTIM_TIMER_A
- * @arg HRTIM_TIMER_B
- * @arg HRTIM_TIMER_C
- * @arg HRTIM_TIMER_D
- * @arg HRTIM_TIMER_E
- * @retval None
- */
-void HRTIM_WaveformCounterStop(HRTIM_TypeDef * HRTIMx,
- uint32_t TimersToStop)
-{
- /* Disable timer(s) counter */
- HRTIMx->HRTIM_MASTER.MCR &= ~TimersToStop;
-}
-
-/**
- * @brief Enables the generation of the waveform signal on the designated output(s)
- * Outputs can be combined (ORed) to allow for simultaneous output enabling
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param OutputsToStart: Timer output(s) to enable
- * This parameter can be any combination of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @retval None
- */
-void HRTIM_WaveformOutputStart(HRTIM_TypeDef * HRTIMx,
- uint32_t OutputsToStart)
-{
- /* Enable the HRTIM outputs */
- HRTIMx->HRTIM_COMMON.OENR = OutputsToStart;
-}
-
-/**
- * @brief Disables the generation of the waveform signal on the designated output(s)
- * Outputs can be combined (ORed) to allow for simultaneous output disabling
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param OutputsToStop: Timer output(s) to disable
- * This parameter can be any combination of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @retval None
- */
-void HRTIM_WaveformOutputStop(HRTIM_TypeDef * HRTIMx,
- uint32_t OutputsToStop)
-{
- /* Disable the HRTIM outputs */
- HRTIMx->HRTIM_COMMON.DISR = OutputsToStop;
-}
-
-/**
- * @brief Enables or disables the Master and slaves interrupt request
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param HRTIM_IT: specifies the HRTIM interrupts sources to be enabled or disabled.
- * This parameter can be any combination of the following values:
- * @arg HRTIM_MASTER_IT_MCMP1: Master compare 1 interrupt source
- * @arg HRTIM_MASTER_IT_MCMP2: Master compare 2 interrupt source
- * @arg HRTIM_MASTER_IT_MCMP3: Master compare 3 interrupt Interrupt source
- * @arg HRTIM_MASTER_IT_MCMP4: Master compare 4 Interrupt source
- * @arg HRTIM_MASTER_IT_MREP: Master Repetition Interrupt source
- * @arg HRTIM_MASTER_IT_SYNC: Synchronization input Interrupt source
- * @arg HRTIM_MASTER_IT_MUPD: Master update Interrupt source
- * @arg HRTIM_TIM_IT_CMP1: Timer compare 1 Interrupt source
- * @arg HRTIM_TIM_IT_CMP2: Timer compare 2 Interrupt source
- * @arg HRTIM_TIM_IT_CMP3: Timer compare 3 Interrupt source
- * @arg HRTIM_TIM_IT_CMP4: Timer compare 4 Interrupt source
- * @arg HRTIM_TIM_IT_REP: Timer repetition Interrupt source
- * @arg HRTIM_TIM_IT_UPD: Timer update Interrupt source
- * @arg HRTIM_TIM_IT_CPT1: Timer capture 1 Interrupt source
- * @arg HRTIM_TIM_IT_CPT2: Timer capture 2 Interrupt source
- * @arg HRTIM_TIM_IT_SET1: Timer output 1 set Interrupt source
- * @arg HRTIM_TIM_IT_RST1: Timer output 1 reset Interrupt source
- * @arg HRTIM_TIM_IT_SET2: Timer output 2 set Interrupt source
- * @arg HRTIM_TIM_IT_RST2: Timer output 2 reset Interrupt source
- * @arg HRTIM_TIM_IT_RST: Timer reset Interrupt source
- * @arg HRTIM_TIM_IT_DLYPRT1: Timer delay protection Interrupt source
- * @param NewState: new state of the TIM interrupts.
- * This parameter can be: ENABLE or DISABLE.
- * @retval None
- */
-void HRTIM_ITConfig(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx, uint32_t HRTIM_IT, FunctionalState NewState)
-{
- if(TimerIdx != HRTIM_TIMERINDEX_MASTER)
- {
- if(NewState != DISABLE)
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxDIER |= HRTIM_IT;
- }
- else
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxDIER &= ~HRTIM_IT;
- }
- }
- else
- {
- if(NewState != DISABLE)
- {
- HRTIMx->HRTIM_MASTER.MDIER |= HRTIM_IT;
- }
- else
- {
- HRTIMx->HRTIM_MASTER.MDIER &= ~HRTIM_IT;
- }
- }
-}
-
-/**
- * @brief Enables or disables the common interrupt request
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param HRTIM_IT: specifies the HRTIM interrupts sources to be enabled or disabled.
- * This parameter can be any combination of the following values:
- * @arg HRTIM_IT_FLT1: Fault 1 interrupt source
- * @arg HRTIM_IT_FLT2: Fault 2 interrupt source
- * @arg HRTIM_IT_FLT3: Fault 3 interrupt Interrupt source
- * @arg HRTIM_IT_FLT4: Fault 4 Interrupt source
- * @arg HRTIM_IT_FLT5: Fault 5 Interrupt source
- * @arg HRTIM_IT_SYSFLT: System Fault Interrupt source
- * @arg HRTIM_IT_DLLRDY: DLL ready Interrupt source
- * @arg HRTIM_IT_BMPER: Burst mode period Interrupt source
- * @param NewState: new state of the TIM interrupts.
- * This parameter can be: ENABLE or DISABLE.
- * @retval None
- */
-void HRTIM_ITCommonConfig(HRTIM_TypeDef * HRTIMx, uint32_t HRTIM_CommonIT, FunctionalState NewState)
-{
- if(NewState != DISABLE)
- {
- HRTIMx->HRTIM_COMMON.IER |= HRTIM_CommonIT;
- }
- else
- {
- HRTIMx->HRTIM_COMMON.IER &= ~HRTIM_CommonIT;
- }
-}
-
-/**
- * @brief Clears the Master and slaves interrupt flags
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param HRTIM_FLAG: specifies the HRTIM flags sources to be cleared.
- * This parameter can be any combination of the following values:
- * @arg HRTIM_MASTER_FLAG_MCMP1: Master compare 1 interrupt flag
- * @arg HRTIM_MASTER_FLAG_MCMP2: Master compare 2 interrupt flag
- * @arg HRTIM_MASTER_FLAG_MCMP3: Master compare 3 interrupt Interrupt flag
- * @arg HRTIM_MASTER_FLAG_MCMP4: Master compare 4 Interrupt flag
- * @arg HRTIM_MASTER_FLAG_MREP: Master Repetition Interrupt flag
- * @arg HRTIM_MASTER_FLAG_SYNC: Synchronization input Interrupt flag
- * @arg HRTIM_MASTER_FLAG_MUPD: Master update Interrupt flag
- * @arg HRTIM_TIM_FLAG_CMP1: Timer compare 1 Interrupt flag
- * @arg HRTIM_TIM_FLAG_CMP2: Timer compare 2 Interrupt flag
- * @arg HRTIM_TIM_FLAG_CMP3: Timer compare 3 Interrupt flag
- * @arg HRTIM_TIM_FLAG_CMP4: Timer compare 4 Interrupt flag
- * @arg HRTIM_TIM_FLAG_REP: Timer repetition Interrupt flag
- * @arg HRTIM_TIM_FLAG_UPD: Timer update Interrupt flag
- * @arg HRTIM_TIM_FLAG_CPT1: Timer capture 1 Interrupt flag
- * @arg HRTIM_TIM_FLAG_CPT2: Timer capture 2 Interrupt flag
- * @arg HRTIM_TIM_FLAG_SET1: Timer output 1 set Interrupt flag
- * @arg HRTIM_TIM_FLAG_RST1: Timer output 1 reset Interrupt flag
- * @arg HRTIM_TIM_FLAG_SET2: Timer output 2 set Interrupt flag
- * @arg HRTIM_TIM_FLAG_RST2: Timer output 2 reset Interrupt flag
- * @arg HRTIM_TIM_FLAG_RST: Timer reset Interrupt flag
- * @arg HRTIM_TIM_FLAG_DLYPRT1: Timer delay protection Interrupt flag
- * @retval None
- */
-void HRTIM_ClearFlag(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx, uint32_t HRTIM_FLAG)
-{
- if(TimerIdx != HRTIM_TIMERINDEX_MASTER)
- {
- HRTIMx->HRTIM_MASTER.MICR |= HRTIM_FLAG;
- }
- else
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxICR |= HRTIM_FLAG;
- }
-}
-
-/**
- * @brief Clears the common interrupt flags
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param HRTIM_FLAG: specifies the HRTIM flags to be cleared.
- * This parameter can be any combination of the following values:
- * @arg HRTIM_FLAG_FLT1: Fault 1 interrupt flag
- * @arg HRTIM_FLAG_FLT2: Fault 2 interrupt flag
- * @arg HRTIM_FLAG_FLT3: Fault 3 interrupt Interrupt flag
- * @arg HRTIM_FLAG_FLT4: Fault 4 Interrupt flag
- * @arg HRTIM_FLAG_FLT5: Fault 5 Interrupt flag
- * @arg HRTIM_FLAG_SYSFLT: System Fault Interrupt flag
- * @arg HRTIM_FLAG_DLLRDY: DLL ready Interrupt flag
- * @arg HRTIM_FLAG_BMPER: Burst mode period Interrupt flag
- * @retval None
- */
-void HRTIM_ClearCommonFlag(HRTIM_TypeDef * HRTIMx, uint32_t HRTIM_CommonFLAG)
-{
- HRTIMx->HRTIM_COMMON.ICR |= HRTIM_CommonFLAG;
-}
-
-/**
- * @brief Clears the Master and slaves interrupt request pending bits
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param HRTIM_IT: specifies the HRTIM interrupts sources to be enabled or disabled.
- * This parameter can be any combination of the following values:
- * @arg HRTIM_MASTER_IT_MCMP1: Master compare 1 interrupt source
- * @arg HRTIM_MASTER_IT_MCMP2: Master compare 2 interrupt source
- * @arg HRTIM_MASTER_IT_MCMP3: Master compare 3 interrupt Interrupt source
- * @arg HRTIM_MASTER_IT_MCMP4: Master compare 4 Interrupt source
- * @arg HRTIM_MASTER_IT_MREP: Master Repetition Interrupt source
- * @arg HRTIM_MASTER_IT_SYNC: Synchronization input Interrupt source
- * @arg HRTIM_MASTER_IT_MUPD: Master update Interrupt source
- * @arg HRTIM_TIM_IT_CMP1: Timer compare 1 Interrupt source
- * @arg HRTIM_TIM_IT_CMP2: Timer compare 2 Interrupt source
- * @arg HRTIM_TIM_IT_CMP3: Timer compare 3 Interrupt source
- * @arg HRTIM_TIM_IT_CMP4: Timer compare 4 Interrupt source
- * @arg HRTIM_TIM_IT_REP: Timer repetition Interrupt source
- * @arg HRTIM_TIM_IT_UPD: Timer update Interrupt source
- * @arg HRTIM_TIM_IT_CPT1: Timer capture 1 Interrupt source
- * @arg HRTIM_TIM_IT_CPT2: Timer capture 2 Interrupt source
- * @arg HRTIM_TIM_IT_SET1: Timer output 1 set Interrupt source
- * @arg HRTIM_TIM_IT_RST1: Timer output 1 reset Interrupt source
- * @arg HRTIM_TIM_IT_SET2: Timer output 2 set Interrupt source
- * @arg HRTIM_TIM_IT_RST2: Timer output 2 reset Interrupt source
- * @arg HRTIM_TIM_IT_RST: Timer reset Interrupt source
- * @arg HRTIM_TIM_IT_DLYPRT: Timer delay protection Interrupt source
- * @retval None
- */
-void HRTIM_ClearITPendingBit(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx, uint32_t HRTIM_IT)
-{
- if(TimerIdx != HRTIM_TIMERINDEX_MASTER)
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxICR |= HRTIM_IT;
- }
- else
- {
- HRTIMx->HRTIM_MASTER.MICR |= HRTIM_IT;
- }
-}
-
-/**
- * @brief Clears the common interrupt pending bits
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param HRTIM_IT: specifies the HRTIM interrupts sources to be cleared.
- * This parameter can be any combination of the following values:
- * @arg HRTIM_IT_FLT1: Fault 1 interrupt source
- * @arg HRTIM_IT_FLT2: Fault 2 interrupt source
- * @arg HRTIM_IT_FLT3: Fault 3 interrupt Interrupt source
- * @arg HRTIM_IT_FLT4: Fault 4 Interrupt source
- * @arg HRTIM_IT_FLT5: Fault 5 Interrupt source
- * @arg HRTIM_IT_SYSFLT: System Fault Interrupt source
- * @arg HRTIM_IT_DLLRDY: DLL ready Interrupt source
- * @arg HRTIM_IT_BMPER: Burst mode period Interrupt source
- * @retval None
- */
-void HRTIM_ClearCommonITPendingBit(HRTIM_TypeDef * HRTIMx, uint32_t HRTIM_CommonIT)
-{
- HRTIMx->HRTIM_COMMON.ICR |= HRTIM_CommonIT;
-}
-
-
-/**
- * @brief Checks whether the specified HRTIM flag is set or not.
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param HRTIM_FLAG: specifies the HRTIM flags to check.
- * This parameter can be any combination of the following values:
- * @arg HRTIM_MASTER_FLAG_MCMP1: Master compare 1 interrupt flag
- * @arg HRTIM_MASTER_FLAG_MCMP2: Master compare 2 interrupt flag
- * @arg HRTIM_MASTER_FLAG_MCMP3: Master compare 3 interrupt Interrupt flag
- * @arg HRTIM_MASTER_FLAG_MCMP4: Master compare 4 Interrupt flag
- * @arg HRTIM_MASTER_FLAG_MREP: Master Repetition Interrupt flag
- * @arg HRTIM_MASTER_FLAG_SYNC: Synchronization input Interrupt flag
- * @arg HRTIM_MASTER_FLAG_MUPD: Master update Interrupt flag
- * @arg HRTIM_TIM_FLAG_CMP1: Timer compare 1 Interrupt flag
- * @arg HRTIM_TIM_FLAG_CMP2: Timer compare 2 Interrupt flag
- * @arg HRTIM_TIM_FLAG_CMP3: Timer compare 3 Interrupt flag
- * @arg HRTIM_TIM_FLAG_CMP4: Timer compare 4 Interrupt flag
- * @arg HRTIM_TIM_FLAG_REP: Timer repetition Interrupt flag
- * @arg HRTIM_TIM_FLAG_UPD: Timer update Interrupt flag
- * @arg HRTIM_TIM_FLAG_CPT1: Timer capture 1 Interrupt flag
- * @arg HRTIM_TIM_FLAG_CPT2: Timer capture 2 Interrupt flag
- * @arg HRTIM_TIM_FLAG_SET1: Timer output 1 set Interrupt flag
- * @arg HRTIM_TIM_FLAG_RST1: Timer output 1 reset Interrupt flag
- * @arg HRTIM_TIM_FLAG_SET2: Timer output 2 set Interrupt flag
- * @arg HRTIM_TIM_FLAG_RST2: Timer output 2 reset Interrupt flag
- * @arg HRTIM_TIM_FLAG_RST: Timer reset Interrupt flag
- * @arg HRTIM_TIM_FLAG_DLYPRT: Timer delay protection Interrupt flag
- * @retval The new state of HRTIM_FLAG (SET or RESET).
- */
-FlagStatus HRTIM_GetFlagStatus(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx, uint32_t HRTIM_FLAG)
-{
- FlagStatus bitstatus = RESET;
-
- if(TimerIdx != HRTIM_TIMERINDEX_MASTER)
- {
- if ((HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxISR & HRTIM_FLAG) != RESET)
- {
- bitstatus = SET;
- }
- else
- {
- bitstatus = RESET;
- }
- }
- else
- {
- if ((HRTIMx->HRTIM_MASTER.MISR & HRTIM_FLAG) != RESET)
- {
- bitstatus = SET;
- }
- else
- {
- bitstatus = RESET;
- }
- }
- return bitstatus;
-}
-
-/**
- * @brief Checks whether the specified HRTIM common flag is set or not.
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param HRTIM_FLAG: specifies the HRTIM flags to check.
- * This parameter can be any combination of the following values:
- * @arg HRTIM_FLAG_FLT1: Fault 1 interrupt flag
- * @arg HRTIM_FLAG_FLT2: Fault 2 interrupt flag
- * @arg HRTIM_FLAG_FLT3: Fault 3 interrupt Interrupt flag
- * @arg HRTIM_FLAG_FLT4: Fault 4 Interrupt flag
- * @arg HRTIM_FLAG_FLT5: Fault 5 Interrupt flag
- * @arg HRTIM_FLAG_SYSFLT: System Fault Interrupt flag
- * @arg HRTIM_FLAG_DLLRDY: DLL ready Interrupt flag
- * @arg HRTIM_FLAG_BMPER: Burst mode period Interrupt flag
- * @retval The new state of HRTIM_FLAG (SET or RESET).
- */
-FlagStatus HRTIM_GetCommonFlagStatus(HRTIM_TypeDef * HRTIMx, uint32_t HRTIM_CommonFLAG)
-{
- FlagStatus bitstatus = RESET;
-
- if((HRTIMx->HRTIM_COMMON.ISR & HRTIM_CommonFLAG) != RESET)
- {
- bitstatus = SET;
- }
- else
- {
- bitstatus = RESET;
- }
- return bitstatus;
-}
-
-/**
- * @brief Checks whether the specified HRTIM interrupt has occurred or not.
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param HRTIM_IT: specifies the HRTIM flags sources to be cleared.
- * This parameter can be any combination of the following values:
- * @arg HRTIM_MASTER_IT_MCMP1: Master compare 1 interrupt
- * @arg HRTIM_MASTER_IT_MCMP2: Master compare 2 interrupt
- * @arg HRTIM_MASTER_IT_MCMP3: Master compare 3 interrupt Interrupt
- * @arg HRTIM_MASTER_IT_MCMP4: Master compare 4 Interrupt
- * @arg HRTIM_MASTER_IT_MREP: Master Repetition Interrupt
- * @arg HRTIM_MASTER_IT_SYNC: Synchronization input Interrupt
- * @arg HRTIM_MASTER_IT_MUPD: Master update Interrupt
- * @arg HRTIM_TIM_IT_CMP1: Timer compare 1 Interrupt
- * @arg HRTIM_TIM_IT_CMP2: Timer compare 2 Interrupt
- * @arg HRTIM_TIM_IT_CMP3: Timer compare 3 Interrupt
- * @arg HRTIM_TIM_IT_CMP4: Timer compare 4 Interrupt
- * @arg HRTIM_TIM_IT_REP: Timer repetition Interrupt
- * @arg HRTIM_TIM_IT_UPD: Timer update Interrupt
- * @arg HRTIM_TIM_IT_CPT1: Timer capture 1 Interrupt
- * @arg HRTIM_TIM_IT_CPT2: Timer capture 2 Interrupt
- * @arg HRTIM_TIM_IT_SET1: Timer output 1 set Interrupt
- * @arg HRTIM_TIM_IT_RST1: Timer output 1 reset Interrupt
- * @arg HRTIM_TIM_IT_SET2: Timer output 2 set Interrupt
- * @arg HRTIM_TIM_IT_RST2: Timer output 2 reset Interrupt
- * @arg HRTIM_TIM_IT_RST: Timer reset Interrupt
- * @arg HRTIM_TIM_IT_DLYPRT: Timer delay protection Interrupt
- * @retval The new state of the HRTIM_IT(SET or RESET).
- */
-ITStatus HRTIM_GetITStatus(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx, uint32_t HRTIM_IT)
-{
- ITStatus bitstatus = RESET;
- uint16_t itstatus = 0x0, itenable = 0x0;
-
- if(TimerIdx != HRTIM_TIMERINDEX_MASTER)
- {
- itstatus = HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxISR & HRTIM_IT;
-
- itenable = HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxDIER & HRTIM_IT;
- if ((itstatus != (uint16_t)RESET) && (itenable != (uint16_t)RESET))
- {
- bitstatus = SET;
- }
- else
- {
- bitstatus = RESET;
- }
- }
- else
- {
- itstatus = HRTIMx->HRTIM_MASTER.MISR & HRTIM_IT;
-
- itenable = HRTIMx->HRTIM_MASTER.MDIER & HRTIM_IT;
- if ((itstatus != (uint16_t)RESET) && (itenable != (uint16_t)RESET))
- {
- bitstatus = SET;
- }
- else
- {
- bitstatus = RESET;
- }
- }
- return bitstatus;
-}
-
-/**
- * @brief Checks whether the specified HRTIM common interrupt has occurred or not.
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param HRTIM_IT: specifies the HRTIM interrupt source to check.
- * This parameter can be any combination of the following values:
- * @arg HRTIM_IT_FLT1: Fault 1 interrupt
- * @arg HRTIM_IT_FLT2: Fault 2 interrupt
- * @arg HRTIM_IT_FLT3: Fault 3 interrupt Interrupt
- * @arg HRTIM_IT_FLT4: Fault 4 Interrupt
- * @arg HRTIM_IT_FLT5: Fault 5 Interrupt
- * @arg HRTIM_IT_SYSFLT: System Fault Interrupt
- * @arg HRTIM_IT_DLLRDY: DLL ready Interrupt flag
- * @arg HRTIM_IT_BMPER: Burst mode period Interrupt
- * @retval The new state of HRTIM_FLAG (SET or RESET).
- */
-ITStatus HRTIM_GetCommonITStatus(HRTIM_TypeDef * HRTIMx, uint32_t HRTIM_CommonIT)
-{
- ITStatus bitstatus = RESET;
- uint16_t itstatus = 0x0, itenable = 0x0;
-
- itstatus = HRTIMx->HRTIM_COMMON.ISR & HRTIM_CommonIT;
- itenable = HRTIMx->HRTIM_COMMON.IER & HRTIM_CommonIT;
-
- if ((itstatus != (uint16_t)RESET) && (itenable != (uint16_t)RESET))
- {
- bitstatus = SET;
- }
- else
- {
- bitstatus = RESET;
- }
-
- return bitstatus;
-}
-
-/**
- * @brief Enables or disables the HRTIMx's DMA Requests.
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param HRTIM_DMA: specifies the DMA Request sources.
- * This parameter can be any combination of the following values:
- * @arg HRTIM_MASTER_DMA_MCMP1: Master compare 1 DMA request source
- * @arg HRTIM_MASTER_DMA_MCMP2: Master compare 2 DMA request source
- * @arg HRTIM_MASTER_DMA_MCMP3: Master compare 3 DMA request source
- * @arg HRTIM_MASTER_DMA_MCMP4: Master compare 4 DMA request source
- * @arg HRTIM_MASTER_DMA_MREP: Master Repetition DMA request source
- * @arg HRTIM_MASTER_DMA_SYNC: Synchronization input DMA request source
- * @arg HRTIM_MASTER_DMA_MUPD:Master update DMA request source
- * @arg HRTIM_TIM_DMA_CMP1: Timer compare 1 DMA request source
- * @arg HRTIM_TIM_DMA_CMP2: Timer compare 2 DMA request source
- * @arg HRTIM_TIM_DMA_CMP3: Timer compare 3 DMA request source
- * @arg HRTIM_TIM_DMA_CMP4: Timer compare 4 DMA request source
- * @arg HRTIM_TIM_DMA_REP: Timer repetition DMA request source
- * @arg HRTIM_TIM_DMA_UPD: Timer update DMA request source
- * @arg HRTIM_TIM_DMA_CPT1: Timer capture 1 DMA request source
- * @arg HRTIM_TIM_DMA_CPT2: Timer capture 2 DMA request source
- * @arg HRTIM_TIM_DMA_SET1: Timer output 1 set DMA request source
- * @arg HRTIM_TIM_DMA_RST1: Timer output 1 reset DMA request source
- * @arg HRTIM_TIM_DMA_SET2: Timer output 2 set DMA request source
- * @arg HRTIM_TIM_DMA_RST2: Timer output 2 reset DMA request source
- * @arg HRTIM_TIM_DMA_RST: Timer reset DMA request source
- * @arg HRTIM_TIM_DMA_DLYPRT: Timer delay protection DMA request source
- * @param NewState: new state of the DMA Request sources.
- * This parameter can be: ENABLE or DISABLE.
- * @retval None
- */
-void HRTIM_DMACmd(HRTIM_TypeDef* HRTIMx, uint32_t TimerIdx, uint32_t HRTIM_DMA, FunctionalState NewState)
-{
- if(TimerIdx != HRTIM_TIMERINDEX_MASTER)
- {
- if(NewState != DISABLE)
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxDIER |= HRTIM_DMA;
- }
- else
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxDIER &= ~HRTIM_DMA;
- }
- }
- else
- {
- if(NewState != DISABLE)
- {
- HRTIMx->HRTIM_MASTER.MDIER |= HRTIM_DMA;
- }
- else
- {
- HRTIMx->HRTIM_MASTER.MDIER &= ~HRTIM_DMA;
- }
- }
-}
-
-/**
- * @}
- */
-
-/** @defgroup HRTIM_Group3 Peripheral Control methods
- * @brief management functions
- *
-@verbatim
- ===============================================================================
- ##### Peripheral Control methods #####
- ===============================================================================
- [..]
- This subsection provides a set of functions allowing to control the HRTIMx data
- transfers.
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Configures an output in basic output compare mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param OCChannel: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @param pBasicOCChannelCfg: pointer to the basic output compare output configuration structure
- * @note When the timer operates in basic output compare mode:
- * Output 1 is implicitely controled by the compare unit 1
- * Output 2 is implicitely controled by the compare unit 2
- * Output Set/Reset crossbar is set according to the selected output compare mode:
- * Toggle: SETxyR = RSTxyR = CMPy
- * Active: SETxyR = CMPy, RSTxyR = 0
- * Inactive: SETxy =0, RSTxy = CMPy
- * @retval None
- */
-void HRTIM_SimpleOCChannelConfig(HRTIM_TypeDef * HRTIM_,
- uint32_t TimerIdx,
- uint32_t OCChannel,
- HRTIM_BasicOCChannelCfgTypeDef* pBasicOCChannelCfg)
-{
- uint32_t CompareUnit = HRTIM_COMPAREUNIT_1;
- HRTIM_CompareCfgTypeDef CompareCfg;
- HRTIM_OutputCfgTypeDef OutputCfg;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, OCChannel));
- assert_param(IS_HRTIM_BASICOCMODE(pBasicOCChannelCfg->Mode));
- assert_param(IS_HRTIM_OUTPUTPOLARITY(pBasicOCChannelCfg->Polarity));
- assert_param(IS_HRTIM_OUTPUTIDLESTATE(pBasicOCChannelCfg->IdleState));
-
- /* Configure timer compare unit */
- switch (OCChannel)
- {
- case HRTIM_OUTPUT_TA1:
- case HRTIM_OUTPUT_TB1:
- case HRTIM_OUTPUT_TC1:
- case HRTIM_OUTPUT_TD1:
- case HRTIM_OUTPUT_TE1:
- {
- CompareUnit = HRTIM_COMPAREUNIT_1;
- }
- break;
- case HRTIM_OUTPUT_TA2:
- case HRTIM_OUTPUT_TB2:
- case HRTIM_OUTPUT_TC2:
- case HRTIM_OUTPUT_TD2:
- case HRTIM_OUTPUT_TE2:
- {
- CompareUnit = HRTIM_COMPAREUNIT_2;
- }
- break;
- default:
- break;
- }
-
- CompareCfg.CompareValue = pBasicOCChannelCfg->Pulse;
- CompareCfg.AutoDelayedMode = HRTIM_AUTODELAYEDMODE_REGULAR;
- CompareCfg.AutoDelayedTimeout = 0;
-
- HRTIM_CompareUnitConfig(HRTIM_,
- TimerIdx,
- CompareUnit,
- &CompareCfg);
-
- /* Configure timer output */
- OutputCfg.Polarity = pBasicOCChannelCfg->Polarity;
- OutputCfg.IdleState = pBasicOCChannelCfg->IdleState;
- OutputCfg.FaultState = HRTIM_OUTPUTFAULTSTATE_NONE;
- OutputCfg.IdleMode = HRTIM_OUTPUTIDLEMODE_NONE;
- OutputCfg.ChopperModeEnable = HRTIM_OUTPUTCHOPPERMODE_DISABLED;
- OutputCfg.BurstModeEntryDelayed = HRTIM_OUTPUTBURSTMODEENTRY_REGULAR;
-
- switch (pBasicOCChannelCfg->Mode)
- {
- case HRTIM_BASICOCMODE_TOGGLE:
- {
- if (CompareUnit == HRTIM_COMPAREUNIT_1)
- {
- OutputCfg.SetSource = HRTIM_OUTPUTSET_TIMCMP1;
- }
- else
- {
- OutputCfg.SetSource = HRTIM_OUTPUTSET_TIMCMP2;
- }
- OutputCfg.ResetSource = OutputCfg.SetSource;
- }
- break;
- case HRTIM_BASICOCMODE_ACTIVE:
- {
- if (CompareUnit == HRTIM_COMPAREUNIT_1)
- {
- OutputCfg.SetSource = HRTIM_OUTPUTSET_TIMCMP1;
- }
- else
- {
- OutputCfg.SetSource = HRTIM_OUTPUTSET_TIMCMP2;
- }
- OutputCfg.ResetSource = HRTIM_OUTPUTRESET_NONE;
- }
- break;
- case HRTIM_BASICOCMODE_INACTIVE:
- {
- if (CompareUnit == HRTIM_COMPAREUNIT_1)
- {
- OutputCfg.ResetSource = HRTIM_OUTPUTRESET_TIMCMP1;
- }
- else
- {
- OutputCfg.ResetSource = HRTIM_OUTPUTRESET_TIMCMP2;
- }
- OutputCfg.SetSource = HRTIM_OUTPUTSET_NONE;
- }
- break;
- default:
- break;
- }
-
- HRTIM_OutputConfig(HRTIM_, TimerIdx, OCChannel, &OutputCfg);
-}
-
-/**
- * @brief Configures an output in basic PWM mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param PWMChannel: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @param pBasicPWMChannelCfg: pointer to the basic PWM output configuration structure
- * @note When the timer operates in basic PWM output mode:
- * Output 1 is implicitly controled by the compare unit 1
- * Output 2 is implicitly controled by the compare unit 2
- * Output Set/Reset crossbar is set as follows:
- * Output 1: SETx1R = CMP1, RSTx1R = PER
- * Output 2: SETx2R = CMP2, RST2R = PER
- * @retval None
- */
-void HRTIM_SimplePWMChannelConfig(HRTIM_TypeDef * HRTIM_,
- uint32_t TimerIdx,
- uint32_t PWMChannel,
- HRTIM_BasicPWMChannelCfgTypeDef* pBasicPWMChannelCfg)
-{
- uint32_t CompareUnit = HRTIM_COMPAREUNIT_1;
- HRTIM_CompareCfgTypeDef CompareCfg;
- HRTIM_OutputCfgTypeDef OutputCfg;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, PWMChannel));
- assert_param(IS_HRTIM_OUTPUTPOLARITY(pBasicPWMChannelCfg->Polarity));
- assert_param(IS_HRTIM_OUTPUTIDLESTATE(pBasicPWMChannelCfg->IdleState));
-
- /* Configure timer compare unit */
- switch (PWMChannel)
- {
- case HRTIM_OUTPUT_TA1:
- case HRTIM_OUTPUT_TB1:
- case HRTIM_OUTPUT_TC1:
- case HRTIM_OUTPUT_TD1:
- case HRTIM_OUTPUT_TE1:
- {
- CompareUnit = HRTIM_COMPAREUNIT_1;
- }
- break;
- case HRTIM_OUTPUT_TA2:
- case HRTIM_OUTPUT_TB2:
- case HRTIM_OUTPUT_TC2:
- case HRTIM_OUTPUT_TD2:
- case HRTIM_OUTPUT_TE2:
- {
- CompareUnit = HRTIM_COMPAREUNIT_2;
- }
- break;
- default:
- break;
- }
-
- CompareCfg.CompareValue = pBasicPWMChannelCfg->Pulse;
- CompareCfg.AutoDelayedMode = HRTIM_AUTODELAYEDMODE_REGULAR;
- CompareCfg.AutoDelayedTimeout = 0;
-
- HRTIM_CompareUnitConfig(HRTIM_,
- TimerIdx,
- CompareUnit,
- &CompareCfg);
-
- /* Configure timer output */
- OutputCfg.Polarity = pBasicPWMChannelCfg->Polarity;
- OutputCfg.IdleState = pBasicPWMChannelCfg->IdleState;
- OutputCfg.FaultState = HRTIM_OUTPUTFAULTSTATE_NONE;
- OutputCfg.IdleMode = HRTIM_OUTPUTIDLEMODE_NONE;
- OutputCfg.ChopperModeEnable = HRTIM_OUTPUTCHOPPERMODE_DISABLED;
- OutputCfg.BurstModeEntryDelayed = HRTIM_OUTPUTBURSTMODEENTRY_REGULAR;
-
- if (CompareUnit == HRTIM_COMPAREUNIT_1)
- {
- OutputCfg.SetSource = HRTIM_OUTPUTSET_TIMCMP1;
- }
- else
- {
- OutputCfg.SetSource = HRTIM_OUTPUTSET_TIMCMP2;
- }
- OutputCfg.ResetSource = HRTIM_OUTPUTSET_TIMPER;
-
- HRTIM_OutputConfig(HRTIM_, TimerIdx, PWMChannel, &OutputCfg);
-}
-
-/**
- * @brief Configures a basic capture
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param CaptureChannel: Capture unit
- * This parameter can be one of the following values:
- * @arg HRTIM_CAPTUREUNIT_1: Capture unit 1
- * @arg HRTIM_CAPTUREUNIT_2: Capture unit 2
- * @param pBasicCaptureChannelCfg: pointer to the basic capture configuration structure
- * @note When the timer operates in basic capture mode the capture is triggered
- * by the designated external event and GPIO input is implicitly used as event source.
- * The cature can be triggered by a rising edge, a falling edge or both
- * edges on event channel.
- * @retval None
- */
-void HRTIM_SimpleCaptureChannelConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t CaptureChannel,
- HRTIM_BasicCaptureChannelCfgTypeDef* pBasicCaptureChannelCfg)
-{
- HRTIM_EventCfgTypeDef EventCfg;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMING_UNIT(TimerIdx));
- assert_param(IS_HRTIM_CAPTUREUNIT(CaptureChannel));
- assert_param(IS_HRTIM_EVENT(pBasicCaptureChannelCfg->Event));
- assert_param(IS_HRTIM_EVENTPOLARITY(pBasicCaptureChannelCfg->EventPolarity));
- assert_param(IS_HRTIM_EVENTSENSITIVITY(pBasicCaptureChannelCfg->EventSensitivity));
- assert_param(IS_HRTIM_EVENTFILTER(pBasicCaptureChannelCfg->EventFilter));
-
- /* Configure external event channel */
- EventCfg.FastMode = HRTIM_EVENTFASTMODE_DISABLE;
- EventCfg.Filter = pBasicCaptureChannelCfg->EventFilter;
- EventCfg.Polarity = pBasicCaptureChannelCfg->EventPolarity;
- EventCfg.Sensitivity = pBasicCaptureChannelCfg->EventSensitivity;
- EventCfg.Source = HRTIM_EVENTSRC_1;
-
- HRTIM_ExternalEventConfig(HRTIMx,
- pBasicCaptureChannelCfg->Event,
- &EventCfg);
-
- /* Memorize capture trigger (will be configured when the capture is started */
- HRTIM_CaptureUnitConfig(HRTIMx,
- TimerIdx,
- CaptureChannel,
- pBasicCaptureChannelCfg->Event);
-}
-
-/**
- * @brief Configures an output basic one pulse mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param OnePulseChannel: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @param pBasicOnePulseChannelCfg: pointer to the basic one pulse output configuration structure
- * @note When the timer operates in basic one pulse mode:
- * the timer counter is implicitly started by the reset event,
- * the reset of the timer counter is triggered by the designated external event
- * GPIO input is implicitly used as event source,
- * Output 1 is implicitly controled by the compare unit 1,
- * Output 2 is implicitly controled by the compare unit 2.
- * Output Set/Reset crossbar is set as follows:
- * Output 1: SETx1R = CMP1, RSTx1R = PER
- * Output 2: SETx2R = CMP2, RST2R = PER
- * The counter mode should be HRTIM_MODE_SINGLESHOT_RETRIGGERABLE
- * @retval None
- */
-void HRTIM_SimpleOnePulseChannelConfig(HRTIM_TypeDef * HRTIM_,
- uint32_t TimerIdx,
- uint32_t OnePulseChannel,
- HRTIM_BasicOnePulseChannelCfgTypeDef* pBasicOnePulseChannelCfg)
-{
- uint32_t CompareUnit = HRTIM_COMPAREUNIT_1;
- HRTIM_CompareCfgTypeDef CompareCfg;
- HRTIM_OutputCfgTypeDef OutputCfg;
- HRTIM_EventCfgTypeDef EventCfg;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, OnePulseChannel));
- assert_param(IS_HRTIM_OUTPUTPOLARITY(pBasicOnePulseChannelCfg->OutputPolarity));
- assert_param(IS_HRTIM_OUTPUTIDLESTATE(pBasicOnePulseChannelCfg->OutputIdleState));
- assert_param(IS_HRTIM_EVENT(pBasicOnePulseChannelCfg->Event));
- assert_param(IS_HRTIM_EVENTPOLARITY(pBasicOnePulseChannelCfg->EventPolarity));
- assert_param(IS_HRTIM_EVENTSENSITIVITY(pBasicOnePulseChannelCfg->EventSensitivity));
- assert_param(IS_HRTIM_EVENTFILTER(pBasicOnePulseChannelCfg->EventFilter));
-
- /* Configure timer compare unit */
- switch (OnePulseChannel)
- {
- case HRTIM_OUTPUT_TA1:
- case HRTIM_OUTPUT_TB1:
- case HRTIM_OUTPUT_TC1:
- case HRTIM_OUTPUT_TD1:
- case HRTIM_OUTPUT_TE1:
- {
- CompareUnit = HRTIM_COMPAREUNIT_1;
- }
- break;
- case HRTIM_OUTPUT_TA2:
- case HRTIM_OUTPUT_TB2:
- case HRTIM_OUTPUT_TC2:
- case HRTIM_OUTPUT_TD2:
- case HRTIM_OUTPUT_TE2:
- {
- CompareUnit = HRTIM_COMPAREUNIT_2;
- }
- break;
- default:
- break;
- }
-
- CompareCfg.CompareValue = pBasicOnePulseChannelCfg->Pulse;
- CompareCfg.AutoDelayedMode = HRTIM_AUTODELAYEDMODE_REGULAR;
- CompareCfg.AutoDelayedTimeout = 0;
-
- HRTIM_CompareUnitConfig(HRTIM_,
- TimerIdx,
- CompareUnit,
- &CompareCfg);
-
- /* Configure timer output */
- OutputCfg.Polarity = pBasicOnePulseChannelCfg->OutputPolarity;
- OutputCfg.IdleState = pBasicOnePulseChannelCfg->OutputIdleState;
- OutputCfg.FaultState = HRTIM_OUTPUTFAULTSTATE_NONE;
- OutputCfg.IdleMode = HRTIM_OUTPUTIDLEMODE_NONE;
- OutputCfg.ChopperModeEnable = HRTIM_OUTPUTCHOPPERMODE_DISABLED;
- OutputCfg.BurstModeEntryDelayed = HRTIM_OUTPUTBURSTMODEENTRY_REGULAR;
-
- if (CompareUnit == HRTIM_COMPAREUNIT_1)
- {
- OutputCfg.SetSource = HRTIM_OUTPUTSET_TIMCMP1;
- }
- else
- {
- OutputCfg.SetSource = HRTIM_OUTPUTSET_TIMCMP2;
- }
- OutputCfg.ResetSource = HRTIM_OUTPUTSET_TIMPER;
-
- HRTIM_OutputConfig(HRTIM_,
- TimerIdx,
- OnePulseChannel,
- &OutputCfg);
-
- /* Configure external event channel */
- EventCfg.FastMode = HRTIM_EVENTFASTMODE_DISABLE;
- EventCfg.Filter = pBasicOnePulseChannelCfg->EventFilter;
- EventCfg.Polarity = pBasicOnePulseChannelCfg->EventPolarity;
- EventCfg.Sensitivity = pBasicOnePulseChannelCfg->EventSensitivity;
- EventCfg.Source = HRTIM_EVENTSRC_1;
-
- HRTIM_ExternalEventConfig(HRTIM_,
- pBasicOnePulseChannelCfg->Event,
- &EventCfg);
-
- /* Configure the timer reset register */
- HRTIM_TIM_ResetConfig(HRTIM_,
- TimerIdx,
- pBasicOnePulseChannelCfg->Event);
-}
-
-/**
- * @brief Configures the general behavior of a timer operating in waveform mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param pTimerCfg: pointer to the timer configuration structure
- * @note When the timer operates in waveform mode, all the features supported by
- * the HRTIMx are available without any limitation.
- * @retval None
- */
-void HRTIM_WaveformTimerConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- HRTIM_TimerCfgTypeDef * pTimerCfg)
-{
- uint32_t HRTIM_timcr;
- uint32_t HRTIM_timfltr;
- uint32_t HRTIM_timoutr;
- uint32_t HRTIM_timrstr;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMING_UNIT(TimerIdx));
- assert_param(IS_HRTIM_TIMPUSHPULLMODE(pTimerCfg->PushPull));
- assert_param(IS_HRTIM_TIMFAULTENABLE(pTimerCfg->FaultEnable));
- assert_param(IS_HRTIM_TIMFAULTLOCK(pTimerCfg->FaultLock));
- assert_param(IS_HRTIM_TIMDEADTIMEINSERTION(pTimerCfg->DeadTimeInsertion));
- assert_param(IS_HRTIM_TIMDELAYEDPROTECTION(pTimerCfg->DelayedProtectionMode));
- assert_param(IS_HRTIM_TIMUPDATETRIGGER(pTimerCfg->UpdateTrigger));
- assert_param(IS_HRTIM_TIMRESETTRIGGER(pTimerCfg->ResetTrigger));
- assert_param(IS_HRTIM_TIMUPDATEONRESET(pTimerCfg->ResetUpdate));
-
- /* Configure timing unit (Timer A to Timer E) */
- HRTIM_timcr = HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxCR;
- HRTIM_timfltr = HRTIMx->HRTIM_TIMERx[TimerIdx].FLTxR;
- HRTIM_timoutr = HRTIMx->HRTIM_TIMERx[TimerIdx].OUTxR;
- HRTIM_timrstr = HRTIMx->HRTIM_TIMERx[TimerIdx].RSTxR;
-
- /* Set the push-pull mode */
- HRTIM_timcr &= ~(HRTIM_TIMCR_PSHPLL);
- HRTIM_timcr |= pTimerCfg->PushPull;
-
- /* Enable/Disable registers update on timer counter reset */
- HRTIM_timcr &= ~(HRTIM_TIMCR_TRSTU);
- HRTIM_timcr |= pTimerCfg->ResetUpdate;
-
- /* Set the timer update trigger */
- HRTIM_timcr &= ~(HRTIM_TIMCR_TIMUPDATETRIGGER);
- HRTIM_timcr |= pTimerCfg->UpdateTrigger;
-
- /* Enable/Disable the fault channel at timer level */
- HRTIM_timfltr &= ~(HRTIM_FLTR_FLTxEN);
- HRTIM_timfltr |= (pTimerCfg->FaultEnable & HRTIM_FLTR_FLTxEN);
-
- /* Lock/Unlock fault sources at timer level */
- HRTIM_timfltr &= ~(HRTIM_FLTR_FLTCLK);
- HRTIM_timfltr |= pTimerCfg->FaultLock;
-
- /* Enable/Disable dead time insertion at timer level */
- HRTIM_timoutr &= ~(HRTIM_OUTR_DTEN);
- HRTIM_timoutr |= pTimerCfg->DeadTimeInsertion;
-
- /* Enable/Disable delayed protection at timer level */
- HRTIM_timoutr &= ~(HRTIM_OUTR_DLYPRT| HRTIM_OUTR_DLYPRTEN);
- HRTIM_timoutr |= pTimerCfg->DelayedProtectionMode;
-
- /* Set the timer counter reset trigger */
- HRTIM_timrstr = pTimerCfg->ResetTrigger;
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxCR = HRTIM_timcr;
- HRTIMx->HRTIM_TIMERx[TimerIdx].FLTxR = HRTIM_timfltr;
- HRTIMx->HRTIM_TIMERx[TimerIdx].OUTxR = HRTIM_timoutr;
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTxR = HRTIM_timrstr;
- }
-
-/**
- * @brief Configures the compare unit of a timer operating in waveform mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * 0xFF for master timer
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param CompareUnit: Compare unit to configure
- * This parameter can be one of the following values:
- * @arg HRTIM_COMPAREUNIT_1: Compare unit 1
- * @arg HRTIM_COMPAREUNIT_2: Compare unit 2
- * @arg HRTIM_COMPAREUNIT_3: Compare unit 3
- * @arg HRTIM_COMPAREUNIT_4: Compare unit 4
- * @param pCompareCfg: pointer to the compare unit configuration structure
- * @note When auto delayed mode is required for compare unit 2 or compare unit 4,
- * application has to configure separately the capture unit. Capture unit
- * to configure in that case depends on the compare unit auto delayed mode
- * is applied to (see below):
- * Auto delayed on output compare 2: capture unit 1 must be configured
- * Auto delayed on output compare 4: capture unit 2 must be configured
- * @retval None
- */
- void HRTIM_WaveformCompareConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t CompareUnit,
- HRTIM_CompareCfgTypeDef* pCompareCfg)
-{
- uint32_t HRTIM_timcr;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMING_UNIT(TimerIdx));
- assert_param(IS_HRTIM_COMPAREUNIT_AUTODELAYEDMODE(CompareUnit, pCompareCfg->AutoDelayedMode));
-
- /* Configure the compare unit */
- switch (CompareUnit)
- {
- case HRTIM_COMPAREUNIT_1:
- {
- /* Set the compare value */
- HRTIMx->HRTIM_TIMERx[TimerIdx].CMP1xR = pCompareCfg->CompareValue;
- }
- break;
- case HRTIM_COMPAREUNIT_2:
- {
- /* Set the compare value */
- HRTIMx->HRTIM_TIMERx[TimerIdx].CMP2xR = pCompareCfg->CompareValue;
-
- if (pCompareCfg->AutoDelayedMode != HRTIM_AUTODELAYEDMODE_REGULAR)
- {
- /* Configure auto-delayed mode */
- HRTIM_timcr = HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxCR;
- HRTIM_timcr &= ~HRTIM_TIMCR_DELCMP2;
- HRTIM_timcr |= pCompareCfg->AutoDelayedMode;
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxCR = HRTIM_timcr;
-
- /* Set the compare value for timeout compare unit (if any) */
- if (pCompareCfg->AutoDelayedMode == HRTIM_AUTODELAYEDMODE_AUTODELAYED_TIMEOUTCMP1)
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CMP1xR = pCompareCfg->AutoDelayedTimeout;
- }
- else if (pCompareCfg->AutoDelayedMode == HRTIM_AUTODELAYEDMODE_AUTODELAYED_TIMEOUTCMP3)
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CMP3xR = pCompareCfg->AutoDelayedTimeout;
- }
- }
- }
- break;
- case HRTIM_COMPAREUNIT_3:
- {
- /* Set the compare value */
- HRTIMx->HRTIM_TIMERx[TimerIdx].CMP3xR = pCompareCfg->CompareValue;
- }
- break;
- case HRTIM_COMPAREUNIT_4:
- {
- /* Set the compare value */
- HRTIMx->HRTIM_TIMERx[TimerIdx].CMP4xR = pCompareCfg->CompareValue;
-
- if (pCompareCfg->AutoDelayedMode != HRTIM_AUTODELAYEDMODE_REGULAR)
- {
- /* Configure auto-delayed mode */
- HRTIM_timcr = HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxCR;
- HRTIM_timcr &= ~HRTIM_TIMCR_DELCMP4;
- HRTIM_timcr |= (pCompareCfg->AutoDelayedMode << 2);
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxCR = HRTIM_timcr;
-
- /* Set the compare value for timeout compare unit (if any) */
- if (pCompareCfg->AutoDelayedMode == HRTIM_AUTODELAYEDMODE_AUTODELAYED_TIMEOUTCMP1)
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CMP1xR = pCompareCfg->AutoDelayedTimeout;
- }
- else if (pCompareCfg->AutoDelayedMode == HRTIM_AUTODELAYEDMODE_AUTODELAYED_TIMEOUTCMP3)
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CMP3xR = pCompareCfg->AutoDelayedTimeout;
- }
- }
- }
- break;
- default:
- break;
- }
-}
-
-/**
- * @brief Sets the HRTIMx Master Comparex Register value
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param CompareUnit: Compare unit to configure
- * This parameter can be one of the following values:
- * @arg HRTIM_COMPAREUNIT_1: Compare unit 1
- * @arg HRTIM_COMPAREUNIT_2: Compare unit 2
- * @arg HRTIM_COMPAREUNIT_3: Compare unit 3
- * @arg HRTIM_COMPAREUNIT_4: Compare unit 4
- * @param Compare: specifies the Comparex register new value
- * @retval None
- */
-void HRTIM_MasterSetCompare(HRTIM_TypeDef * HRTIMx,
- uint32_t CompareUnit,
- uint32_t Compare)
-{
- /* Check parameters */
- assert_param(IS_HRTIM_COMPAREUNIT(CompareUnit));
-
- /* Configure the compare unit */
- switch (CompareUnit)
- {
- case HRTIM_COMPAREUNIT_1:
- {
- /* Set the compare value */
- HRTIMx->HRTIM_MASTER.MCMP1R = Compare;
- }
- break;
- case HRTIM_COMPAREUNIT_2:
- {
- /* Set the compare value */
- HRTIMx->HRTIM_MASTER.MCMP2R = Compare;
- }
- break;
- case HRTIM_COMPAREUNIT_3:
- {
- /* Set the compare value */
- HRTIMx->HRTIM_MASTER.MCMP3R = Compare;
- }
- break;
- case HRTIM_COMPAREUNIT_4:
- {
- /* Set the compare value */
- HRTIMx->HRTIM_MASTER.MCMP4R = Compare;
- }
- break;
- default:
- break;
- }
-}
-/**
- * @brief Configures the capture unit of a timer operating in waveform mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param CaptureChannel: Capture unit to configure
- * This parameter can be one of the following values:
- * @arg HRTIM_CAPTUREUNIT_1: Capture unit 1
- * @arg HRTIM_CAPTUREUNIT_2: Capture unit 2
- * @param pCaptureCfg: pointer to the compare unit configuration structure
- * @retval None
- */
-void HRTIM_WaveformCaptureConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t CaptureUnit,
- HRTIM_CaptureCfgTypeDef* pCaptureCfg)
-{
- /* Configure the capture unit */
- switch (CaptureUnit)
- {
- case HRTIM_CAPTUREUNIT_1:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CPT1xCR = pCaptureCfg->Trigger;
- }
- break;
- case HRTIM_CAPTUREUNIT_2:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CPT2xCR = pCaptureCfg->Trigger;
- }
- break;
- default:
- break;
- }
-}
-
-/**
- * @brief Configures the output of a timer operating in waveform mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param Output: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @param pOutputCfg: pointer to the timer output configuration structure
- * @retval None
- */
-void HRTIM_WaveformOutputConfig(HRTIM_TypeDef * HRTIM_,
- uint32_t TimerIdx,
- uint32_t Output,
- HRTIM_OutputCfgTypeDef * pOutputCfg)
-{
- /* Check parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, Output));
- assert_param(IS_HRTIM_OUTPUTPOLARITY(pOutputCfg->Polarity));
- assert_param(IS_HRTIM_OUTPUTIDLESTATE(pOutputCfg->IdleState));
- assert_param(IS_HRTIM_OUTPUTIDLEMODE(pOutputCfg->IdleMode));
- assert_param(IS_HRTIM_OUTPUTFAULTSTATE(pOutputCfg->FaultState));
- assert_param(IS_HRTIM_OUTPUTCHOPPERMODE(pOutputCfg->ChopperModeEnable));
- assert_param(IS_HRTIM_OUTPUTBURSTMODEENTRY(pOutputCfg->BurstModeEntryDelayed));
-
- /* Configure the timer output */
- HRTIM_OutputConfig(HRTIM_, TimerIdx, Output, pOutputCfg);
-}
-
-/**
- * @brief Configures the event filtering capabilities of a timer (blanking, windowing)
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param Event: external event for which timer event filtering must be configured
- * This parameter can be one of the following values:
- * @arg HRTIM_EVENT_1: External event 1
- * @arg HRTIM_EVENT_2: External event 2
- * @arg HRTIM_EVENT_3: External event 3
- * @arg HRTIM_EVENT_4: External event 4
- * @arg HRTIM_EVENT_5: External event 5
- * @arg HRTIM_EVENT_6: External event 6
- * @arg HRTIM_EVENT_7: External event 7
- * @arg HRTIM_EVENT_8: External event 8
- * @arg HRTIM_EVENT_9: External event 9
- * @arg HRTIM_EVENT_10: External event 10
- * @param pTimerEventFilteringCfg: pointer to the timer event filtering configuration structure
- * @retval None
- */
-void HRTIM_TimerEventFilteringConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t Event,
- HRTIM_TimerEventFilteringCfgTypeDef* pTimerEventFilteringCfg)
-{
- uint32_t HRTIM_eefr;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMING_UNIT(TimerIdx));
- assert_param(IS_HRTIM_EVENT(Event));
- assert_param(IS_HRTIM_TIMEVENTFILTER(pTimerEventFilteringCfg->Filter));
- assert_param(IS_HRTIM_TIMEVENTLATCH(pTimerEventFilteringCfg->Latch));
-
- /* Configure timer event filtering capabilities */
- switch (Event)
- {
- case HRTIM_TIMEVENTFILTER_NONE:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR1 = 0;
- HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR2 = 0;
- }
- break;
- case HRTIM_EVENT_1:
- {
- HRTIM_eefr = HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR1;
- HRTIM_eefr &= ~(HRTIM_EEFR1_EE1FLTR | HRTIM_EEFR1_EE1LTCH);
- HRTIM_eefr |= (pTimerEventFilteringCfg->Filter | pTimerEventFilteringCfg->Latch);
- HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR1 = HRTIM_eefr;
- }
- break;
- case HRTIM_EVENT_2:
- {
- HRTIM_eefr = HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR1;
- HRTIM_eefr &= ~(HRTIM_EEFR1_EE2FLTR | HRTIM_EEFR1_EE2LTCH);
- HRTIM_eefr |= ((pTimerEventFilteringCfg->Filter | pTimerEventFilteringCfg->Latch) << 6);
- HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR1 = HRTIM_eefr;
- }
- break;
- case HRTIM_EVENT_3:
- {
- HRTIM_eefr = HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR1;
- HRTIM_eefr &= ~(HRTIM_EEFR1_EE3FLTR | HRTIM_EEFR1_EE3LTCH);
- HRTIM_eefr |= ((pTimerEventFilteringCfg->Filter | pTimerEventFilteringCfg->Latch) << 12);
- HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR1 = HRTIM_eefr;
- }
- break;
- case HRTIM_EVENT_4:
- {
- HRTIM_eefr = HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR1;
- HRTIM_eefr &= ~(HRTIM_EEFR1_EE4FLTR | HRTIM_EEFR1_EE4LTCH);
- HRTIM_eefr |= ((pTimerEventFilteringCfg->Filter | pTimerEventFilteringCfg->Latch) << 18);
- HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR1 = HRTIM_eefr;
- }
- break;
- case HRTIM_EVENT_5:
- {
- HRTIM_eefr = HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR1;
- HRTIM_eefr &= ~(HRTIM_EEFR1_EE5FLTR | HRTIM_EEFR1_EE5LTCH);
- HRTIM_eefr |= ((pTimerEventFilteringCfg->Filter | pTimerEventFilteringCfg->Latch) << 24);
- HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR1 = HRTIM_eefr;
- }
- break;
- case HRTIM_EVENT_6:
- {
- HRTIM_eefr = HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR2;
- HRTIM_eefr &= ~(HRTIM_EEFR2_EE6FLTR | HRTIM_EEFR2_EE6LTCH);
- HRTIM_eefr |= (pTimerEventFilteringCfg->Filter | pTimerEventFilteringCfg->Latch);
- HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR2 = HRTIM_eefr;
- }
- break;
- case HRTIM_EVENT_7:
- {
- HRTIM_eefr = HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR2;
- HRTIM_eefr &= ~(HRTIM_EEFR2_EE7FLTR | HRTIM_EEFR2_EE7LTCH);
- HRTIM_eefr |= ((pTimerEventFilteringCfg->Filter | pTimerEventFilteringCfg->Latch) << 6);
- HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR2 = HRTIM_eefr;
- }
- break;
- case HRTIM_EVENT_8:
- {
- HRTIM_eefr = HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR2;
- HRTIM_eefr &= ~(HRTIM_EEFR2_EE8FLTR | HRTIM_EEFR2_EE8LTCH);
- HRTIM_eefr |= ((pTimerEventFilteringCfg->Filter | pTimerEventFilteringCfg->Latch) << 12);
- HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR2 = HRTIM_eefr;
- }
- break;
- case HRTIM_EVENT_9:
- {
- HRTIM_eefr = HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR2;
- HRTIM_eefr &= ~(HRTIM_EEFR2_EE9FLTR | HRTIM_EEFR2_EE9LTCH);
- HRTIM_eefr |= ((pTimerEventFilteringCfg->Filter | pTimerEventFilteringCfg->Latch) << 18);
- HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR2 = HRTIM_eefr;
- }
- break;
- case HRTIM_EVENT_10:
- {
- HRTIM_eefr = HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR2;
- HRTIM_eefr &= ~(HRTIM_EEFR2_EE10FLTR | HRTIM_EEFR2_EE10LTCH);
- HRTIM_eefr |= ((pTimerEventFilteringCfg->Filter | pTimerEventFilteringCfg->Latch) << 24);
- HRTIMx->HRTIM_TIMERx[TimerIdx].EEFxR2 = HRTIM_eefr;
- }
- break;
- default:
- break;
- }
-}
-
-/**
- * @brief Configures the dead time insertion feature for a timer
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param pDeadTimeCfg: pointer to the dead time insertion configuration structure
- * @retval None
- */
-void HRTIM_DeadTimeConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- HRTIM_DeadTimeCfgTypeDef* pDeadTimeCfg)
-{
- uint32_t HRTIM_dtr;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMING_UNIT(TimerIdx));
- assert_param(IS_HRTIM_TIMDEADTIME_RISINGSIGN(pDeadTimeCfg->RisingSign));
- assert_param(IS_HRTIM_TIMDEADTIME_RISINGLOCK(pDeadTimeCfg->RisingLock));
- assert_param(IS_HRTIM_TIMDEADTIME_RISINGSIGNLOCK(pDeadTimeCfg->RisingSignLock));
- assert_param(IS_HRTIM_TIMDEADTIME_FALLINGSIGN(pDeadTimeCfg->FallingSign));
- assert_param(IS_HRTIM_TIMDEADTIME_FALLINGLOCK(pDeadTimeCfg->FallingLock));
- assert_param(IS_HRTIM_TIMDEADTIME_FALLINGSIGNLOCK(pDeadTimeCfg->FallingSignLock));
-
- HRTIM_dtr = HRTIMx->HRTIM_TIMERx[TimerIdx].DTxR;
-
- /* Clear timer dead times configuration */
- HRTIM_dtr &= ~(HRTIM_DTR_DTR | HRTIM_DTR_SDTR | HRTIM_DTR_DTPRSC |
- HRTIM_DTR_DTRSLK | HRTIM_DTR_DTRLK | HRTIM_DTR_SDTF |
- HRTIM_DTR_SDTR | HRTIM_DTR_DTFSLK | HRTIM_DTR_DTFLK);
-
- /* Set timer dead times configuration */
- HRTIM_dtr |= (pDeadTimeCfg->Prescaler << 10);
- HRTIM_dtr |= pDeadTimeCfg->RisingValue;
- HRTIM_dtr |= pDeadTimeCfg->RisingSign;
- HRTIM_dtr |= pDeadTimeCfg->RisingSignLock;
- HRTIM_dtr |= pDeadTimeCfg->RisingLock;
- HRTIM_dtr |= (pDeadTimeCfg->FallingValue << 16);
- HRTIM_dtr |= pDeadTimeCfg->FallingSign;
- HRTIM_dtr |= pDeadTimeCfg->FallingSignLock;
- HRTIM_dtr |= pDeadTimeCfg->FallingLock;
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_TIMERx[TimerIdx].DTxR = HRTIM_dtr;
-}
-
-/**
- * @brief Configures the chopper mode feature for a timer
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param pChopperModeCfg: pointer to the chopper mode configuration structure
- * @retval None
- */
-void HRTIM_ChopperModeConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- HRTIM_ChopperModeCfgTypeDef* pChopperModeCfg)
-{
- uint32_t HRTIM_chpr;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMING_UNIT(TimerIdx));
-
- HRTIM_chpr = HRTIMx->HRTIM_TIMERx[TimerIdx].CHPxR;
-
- /* Clear timer chopper mode configuration */
- HRTIM_chpr &= ~(HRTIM_CHPR_CARFRQ | HRTIM_CHPR_CARDTY | HRTIM_CHPR_STRPW);
-
- /* Set timer chopper mode configuration */
- HRTIM_chpr |= pChopperModeCfg->CarrierFreq;
- HRTIM_chpr |= (pChopperModeCfg->DutyCycle << 4);
- HRTIM_chpr |= (pChopperModeCfg->StartPulse << 7);
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_TIMERx[TimerIdx].CHPxR = HRTIM_chpr;
-}
-
-/**
- * @brief Configures the burst DMA controller for a timer
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x5 for master timer
- * @arg 0x0 to 0x4 for timers A to E
- * @param RegistersToUpdate: registers to be written by DMA
- * This parameter can be any combination of the following values:
- * @arg HRTIM_BURSTDMA_CR: HRTIM_MCR or HRTIM_TIMxCR
- * @arg HRTIM_BURSTDMA_ICR: HRTIM_MICR or HRTIM_TIMxICR
- * @arg HRTIM_BURSTDMA_DIER: HRTIM_MDIER or HRTIM_TIMxDIER
- * @arg HRTIM_BURSTDMA_CNT: HRTIM_MCNT or HRTIM_TIMxCNT
- * @arg HRTIM_BURSTDMA_PER: HRTIM_MPER or HRTIM_TIMxPER
- * @arg HRTIM_BURSTDMA_REP: HRTIM_MREP or HRTIM_TIMxREP
- * @arg HRTIM_BURSTDMA_CMP1: HRTIM_MCMP1 or HRTIM_TIMxCMP1
- * @arg HRTIM_BURSTDMA_CMP2: HRTIM_MCMP2 or HRTIM_TIMxCMP2
- * @arg HRTIM_BURSTDMA_CMP3: HRTIM_MCMP3 or HRTIM_TIMxCMP3
- * @arg HRTIM_BURSTDMA_CMP4: HRTIM_MCMP4 or HRTIM_TIMxCMP4
- * @arg HRTIM_BURSTDMA_DTR: HRTIM_TIMxDTR
- * @arg HRTIM_BURSTDMA_SET1R: HRTIM_TIMxSET1R
- * @arg HRTIM_BURSTDMA_RST1R: HRTIM_TIMxRST1R
- * @arg HRTIM_BURSTDMA_SET2R: HRTIM_TIMxSET2R
- * @arg HRTIM_BURSTDMA_RST2R: HRTIM_TIMxRST2R
- * @arg HRTIM_BURSTDMA_EEFR1: HRTIM_TIMxEEFR1
- * @arg HRTIM_BURSTDMA_EEFR2: HRTIM_TIMxEEFR2
- * @arg HRTIM_BURSTDMA_RSTR: HRTIM_TIMxRSTR
- * @arg HRTIM_BURSTDMA_CHPR: HRTIM_TIMxCHPR
- * @arg HRTIM_BURSTDMA_OUTR: HRTIM_TIMxOUTR
- * @arg HRTIM_BURSTDMA_FLTR: HRTIM_TIMxFLTR
- * @retval None
- */
-void HRTIM_BurstDMAConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t RegistersToUpdate)
-{
- /* Check parameters */
- assert_param(IS_HRTIM_TIMER_BURSTDMA(TimerIdx, RegistersToUpdate));
-
- /* Set the burst DMA timer update register */
- switch (TimerIdx)
- {
- case HRTIM_TIMERINDEX_TIMER_A:
- {
- HRTIMx->HRTIM_COMMON.BDTAUPR = RegistersToUpdate;
- }
- break;
- case HRTIM_TIMERINDEX_TIMER_B:
- {
- HRTIMx->HRTIM_COMMON.BDTBUPR = RegistersToUpdate;
- }
- break;
- case HRTIM_TIMERINDEX_TIMER_C:
- {
- HRTIMx->HRTIM_COMMON.BDTCUPR = RegistersToUpdate;
- }
- break;
- case HRTIM_TIMERINDEX_TIMER_D:
- {
- HRTIMx->HRTIM_COMMON.BDTDUPR = RegistersToUpdate;
- }
- break;
- case HRTIM_TIMERINDEX_TIMER_E:
- {
- HRTIMx->HRTIM_COMMON.BDTEUPR = RegistersToUpdate;
- }
- break;
- case HRTIM_TIMERINDEX_MASTER:
- {
- HRTIMx->HRTIM_COMMON.BDMUPDR = RegistersToUpdate;
- }
- break;
- default:
- break;
- }
-}
-
-/**
- * @brief Configures the external input/output synchronization of the HRTIMx
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param pSynchroCfg: pointer to the input/output synchronization configuration structure
- * @retval None
- */
-void HRTIM_SynchronizationConfig(HRTIM_TypeDef *HRTIMx, HRTIM_SynchroCfgTypeDef * pSynchroCfg)
-{
- uint32_t HRTIM_mcr;
-
- /* Check parameters */
- assert_param(IS_HRTIM_SYNCINPUTSOURCE(pSynchroCfg->SyncInputSource));
- assert_param(IS_HRTIM_SYNCOUTPUTSOURCE(pSynchroCfg->SyncOutputSource));
- assert_param(IS_HRTIM_SYNCOUTPUTPOLARITY(pSynchroCfg->SyncOutputPolarity));
-
- HRTIM_mcr = HRTIMx->HRTIM_MASTER.MCR;
-
- /* Set the synchronization input source */
- HRTIM_mcr &= ~(HRTIM_MCR_SYNC_IN);
- HRTIM_mcr |= pSynchroCfg->SyncInputSource;
-
- /* Set the event to be sent on the synchronization output */
- HRTIM_mcr &= ~(HRTIM_MCR_SYNC_SRC);
- HRTIM_mcr |= pSynchroCfg->SyncOutputSource;
-
- /* Set the polarity of the synchronization output */
- HRTIM_mcr &= ~(HRTIM_MCR_SYNC_OUT);
- HRTIM_mcr |= pSynchroCfg->SyncOutputPolarity;
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_MASTER.MCR = HRTIM_mcr;
-}
-
-/**
- * @brief Configures the burst mode feature of the HRTIMx
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param pBurstModeCfg: pointer to the burst mode configuration structure
- * @retval None
- */
-void HRTIM_BurstModeConfig(HRTIM_TypeDef * HRTIMx,
- HRTIM_BurstModeCfgTypeDef* pBurstModeCfg)
-{
- uint32_t HRTIM_bmcr;
-
- /* Check parameters */
- assert_param(IS_HRTIM_BURSTMODE(pBurstModeCfg->Mode));
- assert_param(IS_HRTIM_BURSTMODECLOCKSOURCE(pBurstModeCfg->ClockSource));
- assert_param(IS_HRTIM_HRTIM_BURSTMODEPRESCALER(pBurstModeCfg->Prescaler));
- assert_param(IS_HRTIM_BURSTMODEPRELOAD(pBurstModeCfg->PreloadEnable));
-
- HRTIM_bmcr = HRTIMx->HRTIM_COMMON.BMCR;
-
- /* Set the burst mode operating mode */
- HRTIM_bmcr &= ~(HRTIM_BMCR_BMOM);
- HRTIM_bmcr |= pBurstModeCfg->Mode;
-
- /* Set the burst mode clock source */
- HRTIM_bmcr &= ~(HRTIM_BMCR_BMCLK);
- HRTIM_bmcr |= pBurstModeCfg->ClockSource;
-
- /* Set the burst mode prescaler */
- HRTIM_bmcr &= ~(HRTIM_BMCR_BMPSC);
- HRTIM_bmcr |= pBurstModeCfg->Prescaler;
-
- /* Enable/disable burst mode registers preload */
- HRTIM_bmcr &= ~(HRTIM_BMCR_BMPREN);
- HRTIM_bmcr |= pBurstModeCfg->PreloadEnable;
-
- /* Set the burst mode trigger */
- HRTIMx->HRTIM_COMMON.BMTRGR = pBurstModeCfg->Trigger;
-
- /* Set the burst mode compare value */
- HRTIMx->HRTIM_COMMON.BMCMPR = pBurstModeCfg->IdleDuration;
-
- /* Set the burst mode period */
- HRTIMx->HRTIM_COMMON.BMPER = pBurstModeCfg->Period;
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_COMMON.BMCR = HRTIM_bmcr;
-}
-
-/**
- * @brief Configures the conditioning of an external event
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param Event: external event to configure
- * This parameter can be one of the following values:
- * @arg HRTIM_EVENT_1: External event 1
- * @arg HRTIM_EVENT_2: External event 2
- * @arg HRTIM_EVENT_3: External event 3
- * @arg HRTIM_EVENT_4: External event 4
- * @arg HRTIM_EVENT_5: External event 5
- * @arg HRTIM_EVENT_6: External event 6
- * @arg HRTIM_EVENT_7: External event 7
- * @arg HRTIM_EVENT_8: External event 8
- * @arg HRTIM_EVENT_9: External event 9
- * @arg HRTIM_EVENT_10: External event 10
- * @param pEventCfg: pointer to the event conditioning configuration structure
- * @retval None
- */
-void HRTIM_EventConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t Event,
- HRTIM_EventCfgTypeDef* pEventCfg)
-{
- /* Check parameters */
- assert_param(IS_HRTIM_EVENTSRC(pEventCfg->Source));
- assert_param(IS_HRTIM_EVENTPOLARITY(pEventCfg->Polarity));
- assert_param(IS_HRTIM_EVENTSENSITIVITY(pEventCfg->Sensitivity));
- assert_param(IS_HRTIM_EVENTFASTMODE(pEventCfg->FastMode));
- assert_param(IS_HRTIM_EVENTFILTER(pEventCfg->Filter));
-
- /* Configure the event channel */
- HRTIM_ExternalEventConfig(HRTIMx, Event, pEventCfg);
-
-}
-
-/**
- * @brief Configures the external event conditioning block prescaler
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param Prescaler: Prescaler value
- * This parameter can be one of the following values:
- * @arg HRTIM_EVENTPRESCALER_DIV1: fEEVS=fHRTIMx
- * @arg HRTIM_EVENTPRESCALER_DIV2: fEEVS=fHRTIMx / 2
- * @arg HRTIM_EVENTPRESCALER_DIV4: fEEVS=fHRTIMx / 4
- * @arg HRTIM_EVENTPRESCALER_DIV8: fEEVS=fHRTIMx / 8
- * @retval None
- */
-void HRTIM_EventPrescalerConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t Prescaler)
-{
- uint32_t HRTIM_eecr3;
-
- /* Check parameters */
- assert_param(IS_HRTIM_EVENTPRESCALER(Prescaler));
-
- /* Set the external event prescaler */
- HRTIM_eecr3 = HRTIMx->HRTIM_COMMON.EECR3;
- HRTIM_eecr3 &= ~(HRTIM_EECR3_EEVSD);
- HRTIM_eecr3 |= Prescaler;
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_COMMON.EECR3 = HRTIM_eecr3;
-}
-
-/**
- * @brief Configures the conditioning of fault input
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param Fault: fault input to configure
- * This parameter can be one of the following values:
- * @arg HRTIM_FAULT_1: Fault input 1
- * @arg HRTIM_FAULT_2: Fault input 2
- * @arg HRTIM_FAULT_3: Fault input 3
- * @arg HRTIM_FAULT_4: Fault input 4
- * @arg HRTIM_FAULT_5: Fault input 5
- * @param pFaultCfg: pointer to the fault conditioning configuration structure
- * @retval None
- */
-void HRTIM_FaultConfig(HRTIM_TypeDef * HRTIMx,
- HRTIM_FaultCfgTypeDef* pFaultCfg,
- uint32_t Fault)
-{
- uint32_t HRTIM_fltinr1;
- uint32_t HRTIM_fltinr2;
-
- /* Check parameters */
- assert_param(IS_HRTIM_FAULT(Fault));
- assert_param(IS_HRTIM_FAULTSOURCE(pFaultCfg->Source));
- assert_param(IS_HRTIM_FAULTPOLARITY(pFaultCfg->Polarity));
- assert_param(IS_HRTIM_FAULTFILTER(pFaultCfg->Filter));
- assert_param(IS_HRTIM_FAULTLOCK(pFaultCfg->Lock));
-
- /* Configure fault channel */
- HRTIM_fltinr1 = HRTIMx->HRTIM_COMMON.FLTINxR1;
- HRTIM_fltinr2 = HRTIMx->HRTIM_COMMON.FLTINxR2;
-
- switch (Fault)
- {
- case HRTIM_FAULT_1:
- {
- HRTIM_fltinr1 &= ~(HRTIM_FLTINR1_FLT1P | HRTIM_FLTINR1_FLT1SRC | HRTIM_FLTINR1_FLT1F | HRTIM_FLTINR1_FLT1LCK);
- HRTIM_fltinr1 |= pFaultCfg->Polarity;
- HRTIM_fltinr1 |= pFaultCfg->Source;
- HRTIM_fltinr1 |= pFaultCfg->Filter;
- HRTIM_fltinr1 |= pFaultCfg->Lock;
- }
- break;
- case HRTIM_FAULT_2:
- {
- HRTIM_fltinr1 &= ~(HRTIM_FLTINR1_FLT2P | HRTIM_FLTINR1_FLT2SRC | HRTIM_FLTINR1_FLT2F | HRTIM_FLTINR1_FLT2LCK);
- HRTIM_fltinr1 |= (pFaultCfg->Polarity << 8);
- HRTIM_fltinr1 |= (pFaultCfg->Source << 8);
- HRTIM_fltinr1 |= (pFaultCfg->Filter << 8);
- HRTIM_fltinr1 |= (pFaultCfg->Lock << 8);
- }
- break;
- case HRTIM_FAULT_3:
- {
- HRTIM_fltinr1 &= ~(HRTIM_FLTINR1_FLT3P | HRTIM_FLTINR1_FLT3SRC | HRTIM_FLTINR1_FLT3F | HRTIM_FLTINR1_FLT3LCK);
- HRTIM_fltinr1 |= (pFaultCfg->Polarity << 16);
- HRTIM_fltinr1 |= (pFaultCfg->Source << 16);
- HRTIM_fltinr1 |= (pFaultCfg->Filter << 16);
- HRTIM_fltinr1 |= (pFaultCfg->Lock << 16);
- }
- break;
- case HRTIM_FAULT_4:
- {
- HRTIM_fltinr1 &= ~(HRTIM_FLTINR1_FLT4P | HRTIM_FLTINR1_FLT4SRC | HRTIM_FLTINR1_FLT4F | HRTIM_FLTINR1_FLT4LCK);
- HRTIM_fltinr1 |= (pFaultCfg->Polarity << 24);
- HRTIM_fltinr1 |= (pFaultCfg->Source << 24);
- HRTIM_fltinr1 |= (pFaultCfg->Filter << 24);
- HRTIM_fltinr1 |= (pFaultCfg->Lock << 24);
- }
- break;
- case HRTIM_FAULT_5:
- {
- HRTIM_fltinr2 &= ~(HRTIM_FLTINR2_FLT5P | HRTIM_FLTINR2_FLT5SRC | HRTIM_FLTINR2_FLT5F | HRTIM_FLTINR2_FLT5LCK);
- HRTIM_fltinr2 |= pFaultCfg->Polarity;
- HRTIM_fltinr2 |= pFaultCfg->Source;
- HRTIM_fltinr2 |= pFaultCfg->Filter;
- HRTIM_fltinr2 |= pFaultCfg->Lock;
- }
- break;
- default:
- break;
- }
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_COMMON.FLTINxR1 = HRTIM_fltinr1;
- HRTIMx->HRTIM_COMMON.FLTINxR2 = HRTIM_fltinr2;
-}
-
-/**
- * @brief Configures the fault conditioning block prescaler
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param Prescaler: Prescaler value
- * This parameter can be one of the following values:
- * @arg HRTIM_FAULTPRESCALER_DIV1: fFLTS=fHRTIMx
- * @arg HRTIM_FAULTPRESCALER_DIV2: fFLTS=fHRTIMx / 2
- * @arg HRTIM_FAULTPRESCALER_DIV4: fFLTS=fHRTIMx / 4
- * @arg HRTIM_FAULTPRESCALER_DIV8: fFLTS=fHRTIMx / 8
- * @retval None
- */
-void HRTIM_FaultPrescalerConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t Prescaler)
-{
- uint32_t HRTIM_fltinr2;
-
- /* Check parameters */
- assert_param(IS_HRTIM_FAULTPRESCALER(Prescaler));
-
- /* Set the external event prescaler */
- HRTIM_fltinr2 = HRTIMx->HRTIM_COMMON.FLTINxR2;
- HRTIM_fltinr2 &= ~(HRTIM_FLTINR2_FLTSD);
- HRTIM_fltinr2 |= Prescaler;
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_COMMON.FLTINxR2 = HRTIM_fltinr2;
-}
-
-/**
- * @brief Enables or disables the HRTIMx Fault mode.
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param Fault: fault input to configure
- * This parameter can be one of the following values:
- * @arg HRTIM_FAULT_1: Fault input 1
- * @arg HRTIM_FAULT_2: Fault input 2
- * @arg HRTIM_FAULT_3: Fault input 3
- * @arg HRTIM_FAULT_4: Fault input 4
- * @arg HRTIM_FAULT_5: Fault input 5
- * @param Enable: Fault mode controller enabling
- * This parameter can be one of the following values:
- * @arg HRTIM_FAULT_ENABLED: Fault mode enabled
- * @arg HRTIM_FAULT_DISABLED: Fault mode disabled
- * @retval None
- */
-void HRTIM_FaultModeCtl(HRTIM_TypeDef * HRTIMx, uint32_t Fault, uint32_t Enable)
-{
- uint32_t HRTIM_fltinr1;
- uint32_t HRTIM_fltinr2;
-
- /* Check parameters */
- assert_param(IS_HRTIM_FAULT(Fault));
- assert_param(IS_HRTIM_FAULTCTL(Enable));
-
- /* Configure fault channel */
- HRTIM_fltinr1 = HRTIMx->HRTIM_COMMON.FLTINxR1;
- HRTIM_fltinr2 = HRTIMx->HRTIM_COMMON.FLTINxR2;
-
- switch (Fault)
- {
- case HRTIM_FAULT_1:
- {
- HRTIM_fltinr1 &= ~HRTIM_FLTINR1_FLT1E;
- HRTIM_fltinr1 |= Enable;
- }
- break;
- case HRTIM_FAULT_2:
- {
- HRTIM_fltinr1 &= ~HRTIM_FLTINR1_FLT2E;
- HRTIM_fltinr1 |= (Enable<< 8);
- }
- break;
- case HRTIM_FAULT_3:
- {
- HRTIM_fltinr1 &= ~HRTIM_FLTINR1_FLT3E;
- HRTIM_fltinr1 |= (Enable << 16);
- }
- break;
- case HRTIM_FAULT_4:
- {
- HRTIM_fltinr1 &= ~HRTIM_FLTINR1_FLT4E;
- HRTIM_fltinr1 |= (Enable << 24);
- }
- break;
- case HRTIM_FAULT_5:
- {
- HRTIM_fltinr2 &= ~HRTIM_FLTINR2_FLT5E;
- HRTIM_fltinr2 |= Enable;
- }
- break;
- default:
- break;
- }
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_COMMON.FLTINxR1 = HRTIM_fltinr1;
- HRTIMx->HRTIM_COMMON.FLTINxR2 = HRTIM_fltinr2;
-}
-
-/**
- * @brief Configures both the ADC trigger register update source and the ADC
- * trigger source.
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param ADC trigger: ADC trigger to configure
- * This parameter can be one of the following values:
- * @arg HRTIM_ADCTRIGGER_1: ADC trigger 1
- * @arg HRTIM_ADCTRIGGER_2: ADC trigger 2
- * @arg HRTIM_ADCTRIGGER_3: ADC trigger 3
- * @arg HRTIM_ADCTRIGGER_4: ADC trigger 4
- * @param pADCTriggerCfg: pointer to the ADC trigger configuration structure
- * @retval None
- */
-void HRTIM_ADCTriggerConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t ADCTrigger,
- HRTIM_ADCTriggerCfgTypeDef* pADCTriggerCfg)
-{
- uint32_t HRTIM_cr1;
-
- /* Check parameters */
- assert_param(IS_HRTIM_ADCTRIGGER(ADCTrigger));
- assert_param(IS_HRTIM_ADCTRIGGERUPDATE(pADCTriggerCfg->UpdateSource));
-
- /* Set the ADC trigger update source */
- HRTIM_cr1 = HRTIMx->HRTIM_COMMON.CR1;
-
- switch (ADCTrigger)
- {
- case HRTIM_ADCTRIGGER_1:
- {
- HRTIM_cr1 &= ~(HRTIM_CR1_ADC1USRC);
- HRTIM_cr1 |= pADCTriggerCfg->UpdateSource;
-
- /* Set the ADC trigger 1 source */
- HRTIMx->HRTIM_COMMON.ADC1R = pADCTriggerCfg->Trigger;
- }
- break;
- case HRTIM_ADCTRIGGER_2:
- {
- HRTIM_cr1 &= ~(HRTIM_CR1_ADC2USRC);
- HRTIM_cr1 |= (pADCTriggerCfg->UpdateSource << 3);
-
- /* Set the ADC trigger 2 source */
- HRTIMx->HRTIM_COMMON.ADC2R = pADCTriggerCfg->Trigger;
- }
- break;
- case HRTIM_ADCTRIGGER_3:
- {
- HRTIM_cr1 &= ~(HRTIM_CR1_ADC3USRC);
- HRTIM_cr1 |= (pADCTriggerCfg->UpdateSource << 6);
-
- /* Set the ADC trigger 3 source */
- HRTIMx->HRTIM_COMMON.ADC3R = pADCTriggerCfg->Trigger;
- }
- case HRTIM_ADCTRIGGER_4:
- {
- HRTIM_cr1 &= ~(HRTIM_CR1_ADC4USRC);
- HRTIM_cr1 |= (pADCTriggerCfg->UpdateSource << 9);
-
- /* Set the ADC trigger 4 source */
- HRTIMx->HRTIM_COMMON.ADC4R = pADCTriggerCfg->Trigger;
- }
- break;
- default:
- break;
- }
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_COMMON.CR1 = HRTIM_cr1;
-}
-
-
-/**
- * @brief Enables or disables the HRTIMx burst mode controller.
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param Enable: Burst mode controller enabling
- * This parameter can be one of the following values:
- * @arg HRTIM_BURSTMODECTL_ENABLED: Burst mode enabled
- * @arg HRTIM_BURSTMODECTL_DISABLED: Burst mode disabled
- * @retval None
- */
-void HRTIM_BurstModeCtl(HRTIM_TypeDef * HRTIMx, uint32_t Enable)
-{
- uint32_t HRTIM_bmcr;
-
- /* Check parameters */
- assert_param(IS_HRTIM_BURSTMODECTL(Enable));
-
- /* Enable/Disable the burst mode controller */
- HRTIM_bmcr = HRTIMx->HRTIM_COMMON.BMCR;
- HRTIM_bmcr &= ~(HRTIM_BMCR_BME);
- HRTIM_bmcr |= Enable;
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_COMMON.BMCR = HRTIM_bmcr;
-}
-
-/**
- * @brief Triggers a software capture on the designed capture unit
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param CaptureUnit: Capture unit to trig
- * This parameter can be one of the following values:
- * @arg HRTIM_CAPTUREUNIT_1: Capture unit 1
- * @arg HRTIM_CAPTUREUNIT_2: Capture unit 2
- * @retval None
- * @note The 'software capture' bit in the capure configuration register is
- * automatically reset by hardware
- */
-void HRTIM_SoftwareCapture(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t CaptureUnit)
-{
- /* Check parameters */
- assert_param(IS_HRTIM_TIMING_UNIT(TimerIdx));
- assert_param(IS_HRTIM_CAPTUREUNIT(CaptureUnit));
-
- /* Force a software capture on concerned capture unit */
- switch (CaptureUnit)
- {
- case HRTIM_CAPTUREUNIT_1:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CPT1xCR |= HRTIM_CPT1CR_SWCPT;
- }
- break;
- case HRTIM_CAPTUREUNIT_2:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CPT2xCR |= HRTIM_CPT2CR_SWCPT;
- }
- break;
- default:
- break;
- }
-}
-
-/**
- * @brief Triggers the update of the registers of one or several timers
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimersToUpdate: timers concerned with the software register update
- * This parameter can be any combination of the following values:
- * @arg HRTIM_TIMERUPDATE_MASTER
- * @arg HRTIM_TIMERUPDATE_A
- * @arg HRTIM_TIMERUPDATE_B
- * @arg HRTIM_TIMERUPDATE_C
- * @arg HRTIM_TIMERUPDATE_D
- * @arg HRTIM_TIMERUPDATE_E
- * @retval None
- * @note The 'software update' bits in the HRTIMx control register 2 register are
- * automatically reset by hardware
- */
-void HRTIM_SoftwareUpdate(HRTIM_TypeDef * HRTIMx,
- uint32_t TimersToUpdate)
-{
- /* Check parameters */
- assert_param(IS_HRTIM_TIMERUPDATE(TimersToUpdate));
-
- /* Force timer(s) registers update */
- HRTIMx->HRTIM_COMMON.CR2 |= TimersToUpdate;
-
-}
-
-/**
- * @brief Triggers the reset of one or several timers
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimersToUpdate: timers concerned with the software counter reset
- * This parameter can be any combination of the following values:
- * @arg HRTIM_TIMER_MASTER
- * @arg HRTIM_TIMER_A
- * @arg HRTIM_TIMER_B
- * @arg HRTIM_TIMER_C
- * @arg HRTIM_TIMER_D
- * @arg HRTIM_TIMER_E
- * @retval None
- * @note The 'software reset' bits in the HRTIMx control register 2 are
- * automatically reset by hardware
- */
-void HRTIM_SoftwareReset(HRTIM_TypeDef * HRTIMx,
- uint32_t TimersToReset)
-{
- /* Check parameters */
- assert_param(IS_HRTIM_TIMERRESET(TimersToReset));
-
- /* Force timer(s) registers update */
- HRTIMx->HRTIM_COMMON.CR2 |= TimersToReset;
-
-}
-
-/**
- * @brief Forces the timer output to its active or inactive state
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param Output: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @param OutputLevel: indicates whether the output is forced to its active or inactive state
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUTLEVEL_ACTIVE: output is forced to its active state
- * @arg HRTIM_OUTPUTLEVEL_INACTIVE: output is forced to its inactive state
- * @retval None
- * @note The 'software set/reset trigger' bit in the output set/reset registers
- * is automatically reset by hardware
- */
-void HRTIM_WaveformSetOutputLevel(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t Output,
- uint32_t OutputLevel)
-{
- /* Check parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, Output));
- assert_param(IS_HRTIM_OUTPUTLEVEL(OutputLevel));
-
- /* Force timer output level */
- switch (Output)
- {
- case HRTIM_OUTPUT_TA1:
- case HRTIM_OUTPUT_TB1:
- case HRTIM_OUTPUT_TC1:
- case HRTIM_OUTPUT_TD1:
- case HRTIM_OUTPUT_TE1:
- {
- if (OutputLevel == HRTIM_OUTPUTLEVEL_ACTIVE)
- {
- /* Force output to its active state */
- HRTIMx->HRTIM_TIMERx[TimerIdx].SETx1R |= HRTIM_SET1R_SST;
- }
- else
- {
- /* Force output to its inactive state */
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTx1R |= HRTIM_RST1R_SRT;
- }
- }
- break;
- case HRTIM_OUTPUT_TA2:
- case HRTIM_OUTPUT_TB2:
- case HRTIM_OUTPUT_TC2:
- case HRTIM_OUTPUT_TD2:
- case HRTIM_OUTPUT_TE2:
- {
- if (OutputLevel == HRTIM_OUTPUTLEVEL_ACTIVE)
- {
- /* Force output to its active state */
- HRTIMx->HRTIM_TIMERx[TimerIdx].SETx2R |= HRTIM_SET2R_SST;
- }
- else
- {
- /* Force output to its inactive state */
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTx2R |= HRTIM_RST2R_SRT;
- }
- }
- break;
- default:
- break;
- }
-}
-
-
-/**
- * @}
- */
-
-/** @defgroup HRTIM_Group4 Peripheral State methods
- * @brief Peripheral State functions
- *
-@verbatim
- ===============================================================================
- ##### Peripheral State methods #####
- ===============================================================================
- [..]
- This subsection permit to get in run-time the status of the peripheral
- and the data flow.
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Returns actual value of the capture register of the designated capture unit
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param CaptureUnit: Capture unit to trig
- * This parameter can be one of the following values:
- * @arg HRTIM_CAPTUREUNIT_1: Capture unit 1
- * @arg HRTIM_CAPTUREUNIT_2: Capture unit 2
- * @retval Captured value
- */
-uint32_t HRTIM_GetCapturedValue(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t CaptureUnit)
-{
- uint32_t captured_value = 0;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMING_UNIT(TimerIdx));
- assert_param(IS_HRTIM_CAPTUREUNIT(CaptureUnit));
-
- /* Read captured value */
- switch (CaptureUnit)
- {
- case HRTIM_CAPTUREUNIT_1:
- {
- captured_value = HRTIMx->HRTIM_TIMERx[TimerIdx].CPT1xR;
- }
- break;
- case HRTIM_CAPTUREUNIT_2:
- {
- captured_value = HRTIMx->HRTIM_TIMERx[TimerIdx].CPT2xR;
- }
- break;
- default:
- break;
- }
-
- return captured_value;
-}
-
-/**
- * @brief Returns actual level (active or inactive) of the designated output
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param Output: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @retval Output level
- * @note Returned output level is taken before the output stage (chopper,
- * polarity).
- */
-uint32_t HRTIM_WaveformGetOutputLevel(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t Output)
-{
- uint32_t output_level = HRTIM_OUTPUTLEVEL_INACTIVE;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, Output));
-
- /* Read the output level */
- switch (Output)
- {
- case HRTIM_OUTPUT_TA1:
- case HRTIM_OUTPUT_TB1:
- case HRTIM_OUTPUT_TC1:
- case HRTIM_OUTPUT_TD1:
- case HRTIM_OUTPUT_TE1:
- {
- if ((HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxISR & HRTIM_TIMISR_O1CPY) != RESET)
- {
- output_level = HRTIM_OUTPUTLEVEL_ACTIVE;
- }
- else
- {
- output_level = HRTIM_OUTPUTLEVEL_INACTIVE;
- }
- }
- break;
- case HRTIM_OUTPUT_TA2:
- case HRTIM_OUTPUT_TB2:
- case HRTIM_OUTPUT_TC2:
- case HRTIM_OUTPUT_TD2:
- case HRTIM_OUTPUT_TE2:
- {
- if ((HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxISR & HRTIM_TIMISR_O2CPY) != RESET)
- {
- output_level = HRTIM_OUTPUTLEVEL_ACTIVE;
- }
- else
- {
- output_level = HRTIM_OUTPUTLEVEL_INACTIVE;
- }
- }
- break;
- default:
- break;
- }
-
- return output_level;
-}
-
-/**
- * @brief Returns actual state (RUN, IDLE, FAULT) of the designated output
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param Output: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TE1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TE2: Timer E - Output 2
- * @retval Output state
- */
-uint32_t HRTIM_WaveformGetOutputState(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t Output)
-{
- uint32_t output_bit = 0;
- uint32_t output_state = HRTIM_OUTPUTSTATE_IDLE;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, Output));
-
- /* Set output state according to output control status and output disable status */
- switch (Output)
- {
- case HRTIM_OUTPUT_TA1:
- {
- output_bit = HRTIM_OENR_TA1OEN;
- }
- break;
- case HRTIM_OUTPUT_TA2:
- {
- output_bit = HRTIM_OENR_TA2OEN;
- }
- break;
- case HRTIM_OUTPUT_TB1:
- {
- output_bit = HRTIM_OENR_TB1OEN;
- }
- break;
- case HRTIM_OUTPUT_TB2:
- {
- output_bit = HRTIM_OENR_TB2OEN;
- }
- break;
- case HRTIM_OUTPUT_TC1:
- {
- output_bit = HRTIM_OENR_TC1OEN;
- }
- break;
- case HRTIM_OUTPUT_TC2:
- {
- output_bit = HRTIM_OENR_TC2OEN;
- }
- break;
- case HRTIM_OUTPUT_TD1:
- {
- output_bit = HRTIM_OENR_TD1OEN;
- }
- break;
- case HRTIM_OUTPUT_TD2:
- {
- output_bit = HRTIM_OENR_TD2OEN;
- }
- break;
- case HRTIM_OUTPUT_TE1:
- {
- output_bit = HRTIM_OENR_TE1OEN;
- }
- break;
- case HRTIM_OUTPUT_TE2:
- {
- output_bit = HRTIM_OENR_TE2OEN;
- }
- break;
- default:
- break;
- }
-
- if ((HRTIMx->HRTIM_COMMON.OENR & output_bit) != RESET)
- {
- /* Output is enabled: output in RUN state (whatever ouput disable status is)*/
- output_state = HRTIM_OUTPUTSTATE_RUN;
- }
- else
- {
- if ((HRTIMx->HRTIM_COMMON.ODSR & output_bit) != RESET)
- {
- /* Output is disabled: output in FAULT state */
- output_state = HRTIM_OUTPUTSTATE_FAULT;
- }
- else
- {
- /* Output is disabled: output in IDLE state */
- output_state = HRTIM_OUTPUTSTATE_IDLE;
- }
- }
-
- return(output_state);
-}
-
-/**
- * @brief Returns the level (active or inactive) of the designated output
- * when the delayed protection was triggered
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @param Output: Timer output
- * This parameter can be one of the following values:
- * @arg HRTIM_OUTPUT_TA1: Timer A - Output 1
- * @arg HRTIM_OUTPUT_TA2: Timer A - Output 2
- * @arg HRTIM_OUTPUT_TB1: Timer B - Output 1
- * @arg HRTIM_OUTPUT_TB2: Timer B - Output 2
- * @arg HRTIM_OUTPUT_TC1: Timer C - Output 1
- * @arg HRTIM_OUTPUT_TC2: Timer C - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer D - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer D - Output 2
- * @arg HRTIM_OUTPUT_TD1: Timer E - Output 1
- * @arg HRTIM_OUTPUT_TD2: Timer E - Output 2
- * @retval Delayed protection status
- */
-uint32_t HRTIM_GetDelayedProtectionStatus(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t Output)
-{
- uint32_t delayed_protection_status = HRTIM_OUTPUTLEVEL_INACTIVE;
-
- /* Check parameters */
- assert_param(IS_HRTIM_TIMER_OUTPUT(TimerIdx, Output));
-
- /* Read the delayed protection status */
- switch (Output)
- {
- case HRTIM_OUTPUT_TA1:
- case HRTIM_OUTPUT_TB1:
- case HRTIM_OUTPUT_TC1:
- case HRTIM_OUTPUT_TD1:
- case HRTIM_OUTPUT_TE1:
- {
- if ((HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxISR & HRTIM_TIMISR_O1STAT) != RESET)
- {
- /* Output 1 was active when the delayed idle protection was triggered */
- delayed_protection_status = HRTIM_OUTPUTLEVEL_ACTIVE;
- }
- else
- {
- /* Output 1 was inactive when the delayed idle protection was triggered */
- delayed_protection_status = HRTIM_OUTPUTLEVEL_INACTIVE;
- }
- }
- break;
- case HRTIM_OUTPUT_TA2:
- case HRTIM_OUTPUT_TB2:
- case HRTIM_OUTPUT_TC2:
- case HRTIM_OUTPUT_TD2:
- case HRTIM_OUTPUT_TE2:
- {
- if ((HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxISR & HRTIM_TIMISR_O2STAT) != RESET)
- {
- /* Output 2 was active when the delayed idle protection was triggered */
- delayed_protection_status = HRTIM_OUTPUTLEVEL_ACTIVE;
- }
- else
- {
- /* Output 2 was inactive when the delayed idle protection was triggered */
- delayed_protection_status = HRTIM_OUTPUTLEVEL_INACTIVE;
- }
- }
- break;
- default:
- break;
- }
-
- return delayed_protection_status;
-}
-
-/**
- * @brief Returns the actual status (active or inactive) of the burst mode controller
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @retval Burst mode controller status
- */
-uint32_t HRTIM_GetBurstStatus(HRTIM_TypeDef * HRTIMx)
-{
- uint32_t burst_mode_status;
-
- /* Read burst mode status */
- burst_mode_status = (HRTIMx->HRTIM_COMMON.BMCR & HRTIM_BMCR_BMSTAT);
-
- return burst_mode_status;
-}
-
-/**
- * @brief Indicates on which output the signal is currently active (when the
- * push pull mode is enabled)
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @retval Burst mode controller status
- */
-uint32_t HRTIM_GetCurrentPushPullStatus(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx)
-{
- uint32_t current_pushpull_status;
-
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMING_UNIT(TimerIdx));
-
- /* Read current push pull status */
- current_pushpull_status = (HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxISR & HRTIM_TIMISR_CPPSTAT);
-
- return current_pushpull_status;
-}
-
-
-/**
- * @brief Indicates on which output the signal was applied, in push-pull mode
- balanced fault mode or delayed idle mode, when the protection was triggered
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * This parameter can be one of the following values:
- * @arg 0x0 to 0x4 for timers A to E
- * @retval Idle Push Pull Status
- */
-uint32_t HRTIM_GetIdlePushPullStatus(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx)
-{
- uint32_t idle_pushpull_status;
-
- /* Check the parameters */
- assert_param(IS_HRTIM_TIMING_UNIT(TimerIdx));
-
- /* Read current push pull status */
- idle_pushpull_status = (HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxISR & HRTIM_TIMISR_IPPSTAT);
-
- return idle_pushpull_status;
-}
-
-/**
- * @brief Configures the master timer time base
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @retval None
- */
-void HRTIM_MasterBase_Config(HRTIM_TypeDef * HRTIMx, HRTIM_BaseInitTypeDef* HRTIM_BaseInitStruct)
-{
- /* Set the prescaler ratio */
- HRTIMx->HRTIM_MASTER.MCR &= (uint32_t) ~(HRTIM_MCR_CK_PSC);
- HRTIMx->HRTIM_MASTER.MCR |= (uint32_t)HRTIM_BaseInitStruct->PrescalerRatio;
-
- /* Set the operating mode */
- HRTIMx->HRTIM_MASTER.MCR &= (uint32_t) ~(HRTIM_MCR_CONT | HRTIM_MCR_RETRIG);
- HRTIMx->HRTIM_MASTER.MCR |= (uint32_t)HRTIM_BaseInitStruct->Mode;
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_MASTER.MPER = HRTIM_BaseInitStruct->Period;
- HRTIMx->HRTIM_MASTER.MREP = HRTIM_BaseInitStruct->RepetitionCounter;
-}
-
-/**
- * @brief Configures timing unit (timer A to timer E) time base
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * @retval None
- */
-void HRTIM_TimingUnitBase_Config(HRTIM_TypeDef * HRTIMx, uint32_t TimerIdx, HRTIM_BaseInitTypeDef* HRTIM_BaseInitStruct)
-{
- /* Set the prescaler ratio */
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxCR &= (uint32_t) ~(HRTIM_TIMCR_CK_PSC);
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxCR |= (uint32_t)HRTIM_BaseInitStruct->PrescalerRatio;
-
- /* Set the operating mode */
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxCR &= (uint32_t) ~(HRTIM_TIMCR_CONT | HRTIM_TIMCR_RETRIG);
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxCR |= (uint32_t)HRTIM_BaseInitStruct->Mode;
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_TIMERx[TimerIdx].PERxR = HRTIM_BaseInitStruct->Period;
- HRTIMx->HRTIM_TIMERx[TimerIdx].REPxR = HRTIM_BaseInitStruct->RepetitionCounter;
-}
-
-/**
- * @brief Configures the master timer in waveform mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * @param pTimerInit: pointer to the timer initialization data structure
- * @retval None
- */
-void HRTIM_MasterWaveform_Config(HRTIM_TypeDef * HRTIMx,
- HRTIM_TimerInitTypeDef * pTimerInit)
-{
- uint32_t HRTIM_mcr;
- uint32_t HRTIM_bmcr;
-
- /* Configure master timer */
- HRTIM_mcr = HRTIMx->HRTIM_MASTER.MCR;
- HRTIM_bmcr = HRTIMx->HRTIM_COMMON.BMCR;
-
- /* Enable/Disable the half mode */
- HRTIM_mcr &= ~(HRTIM_MCR_HALF);
- HRTIM_mcr |= pTimerInit->HalfModeEnable;
-
- /* Enable/Disable the timer start upon synchronization event reception */
- HRTIM_mcr &= ~(HRTIM_MCR_SYNCSTRTM);
- HRTIM_mcr |= pTimerInit->StartOnSync;
-
- /* Enable/Disable the timer reset upon synchronization event reception */
- HRTIM_mcr &= ~(HRTIM_MCR_SYNCRSTM);
- HRTIM_mcr |= pTimerInit->ResetOnSync;
-
- /* Enable/Disable the DAC synchronization event generation */
- HRTIM_mcr &= ~(HRTIM_MCR_DACSYNC);
- HRTIM_mcr |= pTimerInit->DACSynchro;
-
- /* Enable/Disable preload mechanism for timer registers */
- HRTIM_mcr &= ~(HRTIM_MCR_PREEN);
- HRTIM_mcr |= pTimerInit->PreloadEnable;
-
- /* Master timer registers update handling */
- HRTIM_mcr &= ~(HRTIM_MCR_BRSTDMA);
- HRTIM_mcr |= (pTimerInit->UpdateGating << 2);
-
- /* Enable/Disable registers update on repetition */
- HRTIM_mcr &= ~(HRTIM_MCR_MREPU);
- HRTIM_mcr |= pTimerInit->RepetitionUpdate;
-
- /* Set the timer burst mode */
- HRTIM_bmcr &= ~(HRTIM_BMCR_MTBM);
- HRTIM_bmcr |= pTimerInit->BurstMode;
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_MASTER.MCR = HRTIM_mcr;
- HRTIMx->HRTIM_COMMON.BMCR = HRTIM_bmcr;
-
-}
-
-/**
- * @brief Configures timing unit (timer A to timer E) in waveform mode
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * @param pTimerInit: pointer to the timer initialization data structure
- * @retval None
- */
-void HRTIM_TimingUnitWaveform_Config(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- HRTIM_TimerInitTypeDef * pTimerInit)
-{
- uint32_t HRTIM_timcr;
- uint32_t HRTIM_bmcr;
-
- /* Configure timing unit */
- HRTIM_timcr = HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxCR;
- HRTIM_bmcr = HRTIMx->HRTIM_COMMON.BMCR;
-
- /* Enable/Disable the half mode */
- HRTIM_timcr &= ~(HRTIM_TIMCR_HALF);
- HRTIM_timcr |= pTimerInit->HalfModeEnable;
-
- /* Enable/Disable the timer start upon synchronization event reception */
- HRTIM_timcr &= ~(HRTIM_TIMCR_SYNCSTRT);
- HRTIM_timcr |= pTimerInit->StartOnSync;
-
- /* Enable/Disable the timer reset upon synchronization event reception */
- HRTIM_timcr &= ~(HRTIM_TIMCR_SYNCRST);
- HRTIM_timcr |= pTimerInit->ResetOnSync;
-
- /* Enable/Disable the DAC synchronization event generation */
- HRTIM_timcr &= ~(HRTIM_TIMCR_DACSYNC);
- HRTIM_timcr |= pTimerInit->DACSynchro;
-
- /* Enable/Disable preload mechanism for timer registers */
- HRTIM_timcr &= ~(HRTIM_TIMCR_PREEN);
- HRTIM_timcr |= pTimerInit->PreloadEnable;
-
- /* Timing unit registers update handling */
- HRTIM_timcr &= ~(HRTIM_TIMCR_UPDGAT);
- HRTIM_timcr |= pTimerInit->UpdateGating;
-
- /* Enable/Disable registers update on repetition */
- HRTIM_timcr &= ~(HRTIM_TIMCR_TREPU);
- if (pTimerInit->RepetitionUpdate == HRTIM_UPDATEONREPETITION_ENABLED)
- {
- HRTIM_timcr |= HRTIM_TIMCR_TREPU;
- }
-
- /* Set the timer burst mode */
- switch (TimerIdx)
- {
- case HRTIM_TIMERINDEX_TIMER_A:
- {
- HRTIM_bmcr &= ~(HRTIM_BMCR_TABM);
- HRTIM_bmcr |= ( pTimerInit->BurstMode << 1);
- }
- break;
- case HRTIM_TIMERINDEX_TIMER_B:
- {
- HRTIM_bmcr &= ~(HRTIM_BMCR_TBBM);
- HRTIM_bmcr |= ( pTimerInit->BurstMode << 2);
- }
- break;
- case HRTIM_TIMERINDEX_TIMER_C:
- {
- HRTIM_bmcr &= ~(HRTIM_BMCR_TCBM);
- HRTIM_bmcr |= ( pTimerInit->BurstMode << 3);
- }
- break;
- case HRTIM_TIMERINDEX_TIMER_D:
- {
- HRTIM_bmcr &= ~(HRTIM_BMCR_TDBM);
- HRTIM_bmcr |= ( pTimerInit->BurstMode << 4);
- }
- break;
- case HRTIM_TIMERINDEX_TIMER_E:
- {
- HRTIM_bmcr &= ~(HRTIM_BMCR_TEBM);
- HRTIM_bmcr |= ( pTimerInit->BurstMode << 5);
- }
- break;
- default:
- break;
- }
-
- /* Update the HRTIMx registers */
- HRTIMx->HRTIM_TIMERx[TimerIdx].TIMxCR = HRTIM_timcr;
- HRTIMx->HRTIM_COMMON.BMCR = HRTIM_bmcr;
-}
-
-/**
- * @brief Configures a compare unit
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * @param CompareUnit: Compare unit identifier
- * @param pCompareCfg: pointer to the compare unit configuration data structure
- * @retval None
- */
-void HRTIM_CompareUnitConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t CompareUnit,
- HRTIM_CompareCfgTypeDef * pCompareCfg)
-{
- if (TimerIdx == HRTIM_TIMERINDEX_MASTER)
- {
- /* Configure the compare unit of the master timer */
- switch (CompareUnit)
- {
- case HRTIM_COMPAREUNIT_1:
- {
- HRTIMx->HRTIM_MASTER.MCMP1R = pCompareCfg->CompareValue;
- }
- break;
- case HRTIM_COMPAREUNIT_2:
- {
- HRTIMx->HRTIM_MASTER.MCMP2R = pCompareCfg->CompareValue;
- }
- break;
- case HRTIM_COMPAREUNIT_3:
- {
- HRTIMx->HRTIM_MASTER.MCMP3R = pCompareCfg->CompareValue;
- }
- break;
- case HRTIM_COMPAREUNIT_4:
- {
- HRTIMx->HRTIM_MASTER.MCMP4R = pCompareCfg->CompareValue;
- }
- break;
- default:
- break;
- }
- }
- else
- {
- /* Configure the compare unit of the timing unit */
- switch (CompareUnit)
- {
- case HRTIM_COMPAREUNIT_1:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CMP1xR = pCompareCfg->CompareValue;
- }
- break;
- case HRTIM_COMPAREUNIT_2:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CMP2xR = pCompareCfg->CompareValue;
- }
- break;
- case HRTIM_COMPAREUNIT_3:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CMP3xR = pCompareCfg->CompareValue;
- }
- break;
- case HRTIM_COMPAREUNIT_4:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CMP4xR = pCompareCfg->CompareValue;
- }
- break;
- default:
- break;
- }
- }
-}
-
-/**
- * @brief Configures a capture unit
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * @param CaptureUnit: Capture unit identifier
- * @param pCaptureCfg: pointer to the compare unit configuration data structure
- * @retval None
- */
-void HRTIM_CaptureUnitConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t CaptureUnit,
- uint32_t Event)
-{
- uint32_t CaptureTrigger = HRTIM_CAPTURETRIGGER_EEV_1;
-
- switch (Event)
- {
- case HRTIM_EVENT_1:
- {
- CaptureTrigger = HRTIM_CAPTURETRIGGER_EEV_1;
- }
- break;
- case HRTIM_EVENT_2:
- {
- CaptureTrigger = HRTIM_CAPTURETRIGGER_EEV_2;
- }
- break;
- case HRTIM_EVENT_3:
- {
- CaptureTrigger = HRTIM_CAPTURETRIGGER_EEV_3;
- }
- break;
- case HRTIM_EVENT_4:
- {
- CaptureTrigger = HRTIM_CAPTURETRIGGER_EEV_4;
- }
- break;
- case HRTIM_EVENT_5:
- {
- CaptureTrigger = HRTIM_CAPTURETRIGGER_EEV_5;
- }
- break;
- case HRTIM_EVENT_6:
- {
- CaptureTrigger = HRTIM_CAPTURETRIGGER_EEV_6;
- }
- break;
- case HRTIM_EVENT_7:
- {
- CaptureTrigger = HRTIM_CAPTURETRIGGER_EEV_7;
- }
- break;
- case HRTIM_EVENT_8:
- {
- CaptureTrigger = HRTIM_CAPTURETRIGGER_EEV_8;
- }
- break;
- case HRTIM_EVENT_9:
- {
- CaptureTrigger = HRTIM_CAPTURETRIGGER_EEV_9;
- }
- break;
- case HRTIM_EVENT_10:
- {
- CaptureTrigger = HRTIM_CAPTURETRIGGER_EEV_10;
- }
- break;
- default:
- break;
-
- }
- switch (CaptureUnit)
- {
- case HRTIM_CAPTUREUNIT_1:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CPT1xCR = CaptureTrigger;
- }
- break;
- case HRTIM_CAPTUREUNIT_2:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].CPT2xCR = CaptureTrigger;
- }
- break;
- default:
- break;
- }
-}
-
-/**
- * @brief Configures the output of a timing unit
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * @param Output: timing unit output identifier
- * @param pOutputCfg: pointer to the output configuration data structure
- * @retval None
- */
-void HRTIM_OutputConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t Output,
- HRTIM_OutputCfgTypeDef * pOutputCfg)
-{
- uint32_t HRTIM_outr;
- uint32_t shift = 0;
-
- HRTIM_outr = HRTIMx->HRTIM_TIMERx[TimerIdx].OUTxR;
-
- switch (Output)
- {
- case HRTIM_OUTPUT_TA1:
- case HRTIM_OUTPUT_TB1:
- case HRTIM_OUTPUT_TC1:
- case HRTIM_OUTPUT_TD1:
- case HRTIM_OUTPUT_TE1:
- {
- /* Set the output set/reset crossbar */
- HRTIMx->HRTIM_TIMERx[TimerIdx].SETx1R = pOutputCfg->SetSource;
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTx1R = pOutputCfg->ResetSource;
-
- shift = 0;
- }
- break;
- case HRTIM_OUTPUT_TA2:
- case HRTIM_OUTPUT_TB2:
- case HRTIM_OUTPUT_TC2:
- case HRTIM_OUTPUT_TD2:
- case HRTIM_OUTPUT_TE2:
- {
- /* Set the output set/reset crossbar */
- HRTIMx->HRTIM_TIMERx[TimerIdx].SETx2R = pOutputCfg->SetSource;
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTx2R = pOutputCfg->ResetSource;
-
- shift = 16;
- }
- break;
- default:
- break;
- }
-
- /* Clear output config */
- HRTIM_outr &= ~((HRTIM_OUTR_POL1 |
- HRTIM_OUTR_IDLM1 |
- HRTIM_OUTR_IDLES1|
- HRTIM_OUTR_FAULT1|
- HRTIM_OUTR_CHP1 |
- HRTIM_OUTR_DIDL1) << shift);
-
- /* Set the polarity */
- HRTIM_outr |= (pOutputCfg->Polarity << shift);
-
- /* Set the IDLE mode */
- HRTIM_outr |= (pOutputCfg->IdleMode << shift);
-
- /* Set the IDLE state */
- HRTIM_outr |= (pOutputCfg->IdleState << shift);
-
- /* Set the FAULT state */
- HRTIM_outr |= (pOutputCfg->FaultState << shift);
-
- /* Set the chopper mode */
- HRTIM_outr |= (pOutputCfg->ChopperModeEnable << shift);
-
- /* Set the burst mode entry mode */
- HRTIM_outr |= (pOutputCfg->BurstModeEntryDelayed << shift);
-
- /* Update HRTIMx register */
- HRTIMx->HRTIM_TIMERx[TimerIdx].OUTxR = HRTIM_outr;
-}
-
-/**
- * @brief Configures an external event channel
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param Event: Event channel identifier
- * @param pEventCfg: pointer to the event channel configuration data structure
- * @retval None
- */
-static void HRTIM_ExternalEventConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t Event,
- HRTIM_EventCfgTypeDef *pEventCfg)
-{
- uint32_t hrtim_eecr1;
- uint32_t hrtim_eecr2;
- uint32_t hrtim_eecr3;
-
- /* Configure external event channel */
- hrtim_eecr1 = HRTIMx->HRTIM_COMMON.EECR1;
- hrtim_eecr2 = HRTIMx->HRTIM_COMMON.EECR2;
- hrtim_eecr3 = HRTIMx->HRTIM_COMMON.EECR3;
-
- switch (Event)
- {
- case HRTIM_EVENT_1:
- {
- hrtim_eecr1 &= ~(HRTIM_EECR1_EE1SRC | HRTIM_EECR1_EE1POL | HRTIM_EECR1_EE1SNS | HRTIM_EECR1_EE1FAST);
- hrtim_eecr1 |= pEventCfg->Source;
- hrtim_eecr1 |= pEventCfg->Polarity;
- hrtim_eecr1 |= pEventCfg->Sensitivity;
- /* Update the HRTIM registers (all bit fields but EE1FAST bit) */
- HRTIMx->HRTIM_COMMON.EECR1 = hrtim_eecr1;
- /* Update the HRTIM registers (EE1FAST bit) */
- hrtim_eecr1 |= pEventCfg->FastMode;
- HRTIMx->HRTIM_COMMON.EECR1 = hrtim_eecr1;
- }
- break;
- case HRTIM_EVENT_2:
- {
- hrtim_eecr1 &= ~(HRTIM_EECR1_EE2SRC | HRTIM_EECR1_EE2POL | HRTIM_EECR1_EE2SNS | HRTIM_EECR1_EE2FAST);
- hrtim_eecr1 |= (pEventCfg->Source << 6);
- hrtim_eecr1 |= (pEventCfg->Polarity << 6);
- hrtim_eecr1 |= (pEventCfg->Sensitivity << 6);
- /* Update the HRTIM registers (all bit fields but EE2FAST bit) */
- HRTIMx->HRTIM_COMMON.EECR1 = hrtim_eecr1;
- /* Update the HRTIM registers (EE2FAST bit) */
- hrtim_eecr1 |= (pEventCfg->FastMode << 6);
- HRTIMx->HRTIM_COMMON.EECR1 = hrtim_eecr1;
- }
- break;
- case HRTIM_EVENT_3:
- {
- hrtim_eecr1 &= ~(HRTIM_EECR1_EE3SRC | HRTIM_EECR1_EE3POL | HRTIM_EECR1_EE3SNS | HRTIM_EECR1_EE3FAST);
- hrtim_eecr1 |= (pEventCfg->Source << 12);
- hrtim_eecr1 |= (pEventCfg->Polarity << 12);
- hrtim_eecr1 |= (pEventCfg->Sensitivity << 12);
- /* Update the HRTIM registers (all bit fields but EE3FAST bit) */
- HRTIMx->HRTIM_COMMON.EECR1 = hrtim_eecr1;
- /* Update the HRTIM registers (EE3FAST bit) */
- hrtim_eecr1 |= (pEventCfg->FastMode << 12);
- HRTIMx->HRTIM_COMMON.EECR1 = hrtim_eecr1;
- }
- break;
- case HRTIM_EVENT_4:
- {
- hrtim_eecr1 &= ~(HRTIM_EECR1_EE4SRC | HRTIM_EECR1_EE4POL | HRTIM_EECR1_EE4SNS | HRTIM_EECR1_EE4FAST);
- hrtim_eecr1 |= (pEventCfg->Source << 18);
- hrtim_eecr1 |= (pEventCfg->Polarity << 18);
- hrtim_eecr1 |= (pEventCfg->Sensitivity << 18);
- /* Update the HRTIM registers (all bit fields but EE4FAST bit) */
- HRTIMx->HRTIM_COMMON.EECR1 = hrtim_eecr1;
- /* Update the HRTIM registers (EE4FAST bit) */
- hrtim_eecr1 |= (pEventCfg->FastMode << 18);
- HRTIMx->HRTIM_COMMON.EECR1 = hrtim_eecr1;
- }
- break;
- case HRTIM_EVENT_5:
- {
- hrtim_eecr1 &= ~(HRTIM_EECR1_EE5SRC | HRTIM_EECR1_EE5POL | HRTIM_EECR1_EE5SNS | HRTIM_EECR1_EE5FAST);
- hrtim_eecr1 |= (pEventCfg->Source << 24);
- hrtim_eecr1 |= (pEventCfg->Polarity << 24);
- hrtim_eecr1 |= (pEventCfg->Sensitivity << 24);
- /* Update the HRTIM registers (all bit fields but EE5FAST bit) */
- HRTIMx->HRTIM_COMMON.EECR1 = hrtim_eecr1;
- /* Update the HRTIM registers (EE5FAST bit) */
- hrtim_eecr1 |= (pEventCfg->FastMode << 24);
- HRTIMx->HRTIM_COMMON.EECR1 = hrtim_eecr1;
- }
- break;
- case HRTIM_EVENT_6:
- {
- hrtim_eecr2 &= ~(HRTIM_EECR2_EE6SRC | HRTIM_EECR2_EE6POL | HRTIM_EECR2_EE6SNS);
- hrtim_eecr2 |= pEventCfg->Source;
- hrtim_eecr2 |= pEventCfg->Polarity;
- hrtim_eecr2 |= pEventCfg->Sensitivity;
- hrtim_eecr3 &= ~(HRTIM_EECR3_EE6F);
- hrtim_eecr3 |= pEventCfg->Filter;
- /* Update the HRTIM registers */
- HRTIMx->HRTIM_COMMON.EECR2 = hrtim_eecr2;
- HRTIMx->HRTIM_COMMON.EECR3 = hrtim_eecr3;
- }
- break;
- case HRTIM_EVENT_7:
- {
- hrtim_eecr2 &= ~(HRTIM_EECR2_EE7SRC | HRTIM_EECR2_EE7POL | HRTIM_EECR2_EE7SNS);
- hrtim_eecr2 |= (pEventCfg->Source << 6);
- hrtim_eecr2 |= (pEventCfg->Polarity << 6);
- hrtim_eecr2 |= (pEventCfg->Sensitivity << 6);
- hrtim_eecr3 &= ~(HRTIM_EECR3_EE7F);
- hrtim_eecr3 |= (pEventCfg->Filter << 6);
- /* Update the HRTIM registers */
- HRTIMx->HRTIM_COMMON.EECR2 = hrtim_eecr2;
- HRTIMx->HRTIM_COMMON.EECR3 = hrtim_eecr3;
- }
- break;
- case HRTIM_EVENT_8:
- {
- hrtim_eecr2 &= ~(HRTIM_EECR2_EE8SRC | HRTIM_EECR2_EE8POL | HRTIM_EECR2_EE8SNS);
- hrtim_eecr2 |= (pEventCfg->Source << 12);
- hrtim_eecr2 |= (pEventCfg->Polarity << 12);
- hrtim_eecr2 |= (pEventCfg->Sensitivity << 12);
- hrtim_eecr3 &= ~(HRTIM_EECR3_EE8F);
- hrtim_eecr3 |= (pEventCfg->Filter << 12);
- /* Update the HRTIM registers */
- HRTIMx->HRTIM_COMMON.EECR2 = hrtim_eecr2;
- HRTIMx->HRTIM_COMMON.EECR3 = hrtim_eecr3;
- }
- break;
- case HRTIM_EVENT_9:
- {
- hrtim_eecr2 &= ~(HRTIM_EECR2_EE9SRC | HRTIM_EECR2_EE9POL | HRTIM_EECR2_EE9SNS);
- hrtim_eecr2 |= (pEventCfg->Source << 18);
- hrtim_eecr2 |= (pEventCfg->Polarity << 18);
- hrtim_eecr2 |= (pEventCfg->Sensitivity << 18);
- hrtim_eecr3 &= ~(HRTIM_EECR3_EE9F);
- hrtim_eecr3 |= (pEventCfg->Filter << 18);
- /* Update the HRTIM registers */
- HRTIMx->HRTIM_COMMON.EECR2 = hrtim_eecr2;
- HRTIMx->HRTIM_COMMON.EECR3 = hrtim_eecr3;
- }
- break;
- case HRTIM_EVENT_10:
- {
- hrtim_eecr2 &= ~(HRTIM_EECR2_EE10SRC | HRTIM_EECR2_EE10POL | HRTIM_EECR2_EE10SNS);
- hrtim_eecr2 |= (pEventCfg->Source << 24);
- hrtim_eecr2 |= (pEventCfg->Polarity << 24);
- hrtim_eecr2 |= (pEventCfg->Sensitivity << 24);
- hrtim_eecr3 &= ~(HRTIM_EECR3_EE10F);
- hrtim_eecr3 |= (pEventCfg->Filter << 24);
- /* Update the HRTIM registers */
- HRTIMx->HRTIM_COMMON.EECR2 = hrtim_eecr2;
- HRTIMx->HRTIM_COMMON.EECR3 = hrtim_eecr3;
- }
- break;
- default:
- break;
- }
-}
-
-/**
- * @brief Configures the timer counter reset
- * @param HRTIMx: pointer to HRTIMx peripheral
- * @param TimerIdx: Timer index
- * @param Event: Event channel identifier
- * @retval None
- */
-void HRTIM_TIM_ResetConfig(HRTIM_TypeDef * HRTIMx,
- uint32_t TimerIdx,
- uint32_t Event)
-{
- switch (Event)
- {
- case HRTIM_EVENT_1:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTxR = HRTIM_TIMRESETTRIGGER_EEV_1;
- }
- break;
- case HRTIM_EVENT_2:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTxR = HRTIM_TIMRESETTRIGGER_EEV_2;
- }
- break;
- case HRTIM_EVENT_3:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTxR = HRTIM_TIMRESETTRIGGER_EEV_3;
- }
- break;
- case HRTIM_EVENT_4:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTxR = HRTIM_TIMRESETTRIGGER_EEV_4;
- }
- break;
- case HRTIM_EVENT_5:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTxR = HRTIM_TIMRESETTRIGGER_EEV_5;
- }
- break;
- case HRTIM_EVENT_6:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTxR = HRTIM_TIMRESETTRIGGER_EEV_6;
- }
- break;
- case HRTIM_EVENT_7:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTxR = HRTIM_TIMRESETTRIGGER_EEV_7;
- }
- break;
- case HRTIM_EVENT_8:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTxR = HRTIM_TIMRESETTRIGGER_EEV_8;
- }
- break;
- case HRTIM_EVENT_9:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTxR = HRTIM_TIMRESETTRIGGER_EEV_9;
- }
- break;
- case HRTIM_EVENT_10:
- {
- HRTIMx->HRTIM_TIMERx[TimerIdx].RSTxR = HRTIM_TIMRESETTRIGGER_EEV_10;
- }
- break;
- default:
- break;
- }
-}
-/**
- * @}
- */
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
-
-
-
projects / qmk_firmware.git / blobdiff