+++ /dev/null
-/**
- ******************************************************************************
- * @file stm32f3xx_hal_smbus.c
- * @author MCD Application Team
- * @version V1.1.0
- * @date 12-Sept-2014
- * @brief SMBUS HAL module driver.
- *
- * This file provides firmware functions to manage the following
- * functionalities of the System Management Bus (SMBus) peripheral,
- * based on I2C principales of operation :
- * + Initialization and de-initialization functions
- * + IO operation functions
- * + Peripheral State and Errors functions
- *
- @verbatim
- ==============================================================================
- ##### How to use this driver #####
- ==============================================================================
- [..]
- The SMBUS HAL driver can be used as follows:
-
- (#) Declare a SMBUS_HandleTypeDef handle structure, for example:
- SMBUS_HandleTypeDef hsmbus;
-
- (#)Initialize the SMBUS low level resources by implement the HAL_SMBUS_MspInit ()API:
- (##) Enable the SMBUSx interface clock
- (##) SMBUS pins configuration
- (+++) Enable the clock for the SMBUS GPIOs
- (+++) Configure SMBUS pins as alternate function open-drain
- (##) NVIC configuration if you need to use interrupt process
- (+++) Configure the SMBUSx interrupt priority
- (+++) Enable the NVIC SMBUS IRQ Channel
-
- (#) Configure the Communication Clock Timing, Bus Timeout, Own Address1, Master Adressing Mode,
- Dual Addressing mode, Own Address2, Own Address2 Mask, General call, Nostretch mode,
- Peripheral mode and Packet Error Check mode in the hsmbus Init structure.
-
- (#) Initialize the SMBUS registers by calling the HAL_SMBUS_Init() API:
- (+) These API's configures also the low level Hardware GPIO, CLOCK, CORTEX...etc)
- by calling the customed HAL_SMBUS_MspInit(&hsmbus) API.
-
- (#) To check if target device is ready for communication, use the function HAL_SMBUS_IsDeviceReady()
-
- (#) For SMBUS IO operations, only one mode of operations is available within this driver :
-
- *** Interrupt mode IO operation ***
- ===================================
- [..]
- (+) Transmit in master/host SMBUS mode an amount of data in non blocking mode using HAL_SMBUS_Master_Transmit_IT()
- (++) At transmission end of transfer HAL_SMBUS_MasterTxCpltCallback is executed and user can
- add his own code by customization of function pointer HAL_SMBUS_MasterTxCpltCallback
- (+) Receive in master/host SMBUS mode an amount of data in non blocking mode using HAL_SMBUS_Master_Receive_IT()
- (++) At reception end of transfer HAL_SMBUS_MasterRxCpltCallback is executed and user can
- add his own code by customization of function pointer HAL_SMBUS_MasterRxCpltCallback
- (+) Abort a master/host SMBUS process commnunication with Interrupt using HAL_SMBUS_Master_Abort_IT()
- (++) The associated previous transfer callback is called at the end of abort process
- (++) mean HAL_SMBUS_MasterTxCpltCallback in case of previous state was master transmit
- (++) mean HAL_SMBUS_MasterRxCpltCallback in case of previous state was master receive
- (+) Enable/disable the Address listen mode in slave/device or host/slave SMBUS mode
- using HAL_SMBUS_Slave_Listen_IT() HAL_SMBUS_DisableListen_IT()
- (++) When address slave/device SMBUS match, HAL_SMBUS_SlaveAddrCallback is executed and user can
- add his own code to check the Address Match Code and the transmission direction request by master/host (Write/Read).
- (++) At Listen mode end HAL_SMBUS_SlaveListenCpltCallback is executed and user can
- add his own code by customization of function pointer HAL_SMBUS_SlaveListenCpltCallback
- (+) Transmit in slave/device SMBUS mode an amount of data in non blocking mode using HAL_SMBUS_Slave_Transmit_IT()
- (++) At transmission end of transfer HAL_SMBUS_SlaveTxCpltCallback is executed and user can
- add his own code by customization of function pointer HAL_SMBUS_SlaveTxCpltCallback
- (+) Receive in slave/device SMBUS mode an amount of data in non blocking mode using HAL_SMBUS_Slave_Receive_IT()
- (++) At reception end of transfer HAL_SMBUS_SlaveRxCpltCallback is executed and user can
- add his own code by customization of function pointer HAL_SMBUS_SlaveRxCpltCallback
- (+) Enable/Disable the SMBUS alert mode using HAL_SMBUS_EnableAlert_IT() HAL_SMBUS_DisableAlert_IT()
- (++) When SMBUS Alert is generated HAL_SMBUS_ErrorCallback() is executed and user can
- add his own code by customization of function pointer HAL_SMBUS_ErrorCallback
- to check the Alert Error Code using function HAL_SMBUS_GetError()
- (+) Get HAL state machine or error values using HAL_SMBUS_GetState() or HAL_SMBUS_GetError()
- (+) In case of transfer Error, HAL_SMBUS_ErrorCallback() function is executed and user can
- add his own code by customization of function pointer HAL_SMBUS_ErrorCallback
- to check the Error Code using function HAL_SMBUS_GetError()
-
- *** SMBUS HAL driver macros list ***
- ==================================
- [..]
- Below the list of most used macros in SMBUS HAL driver.
-
- (+) __HAL_SMBUS_ENABLE: Enable the SMBUS peripheral
- (+) __HAL_SMBUS_DISABLE: Disable the SMBUS peripheral
- (+) __HAL_SMBUS_GET_FLAG : Checks whether the specified SMBUS flag is set or not
- (+) __HAL_SMBUS_CLEAR_FLAG : Clears the specified SMBUS pending flag
- (+) __HAL_SMBUS_ENABLE_IT: Enables the specified SMBUS interrupt
- (+) __HAL_SMBUS_DISABLE_IT: Disables the specified SMBUS interrupt
-
- [..]
- (@) You can refer to the SMBUS HAL driver header file for more useful macros
-
-
- @endverbatim
- ******************************************************************************
- * @attention
- *
- * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/* Includes ------------------------------------------------------------------*/
-#include "stm32f3xx_hal.h"
-
-/** @addtogroup STM32F3xx_HAL_Driver
- * @{
- */
-
-/** @defgroup SMBUS SMBUS HAL module driver
- * @brief SMBUS HAL module driver
- * @{
- */
-
-#ifdef HAL_SMBUS_MODULE_ENABLED
-
-/* Private typedef -----------------------------------------------------------*/
-/* Private define ------------------------------------------------------------*/
-/** @defgroup SMBUS_Private_Define SMBUS Private Define
- * @{
- */
-#define TIMING_CLEAR_MASK ((uint32_t)0xF0FFFFFF) /*<! SMBUS TIMING clear register Mask */
-#define HAL_TIMEOUT_ADDR ((uint32_t)10000) /* 10 s */
-#define HAL_TIMEOUT_BUSY ((uint32_t)25) /* 25 ms */
-#define HAL_TIMEOUT_DIR ((uint32_t)25) /* 25 ms */
-#define HAL_TIMEOUT_RXNE ((uint32_t)25) /* 25 ms */
-#define HAL_TIMEOUT_STOPF ((uint32_t)25) /* 25 ms */
-#define HAL_TIMEOUT_TC ((uint32_t)25) /* 25 ms */
-#define HAL_TIMEOUT_TCR ((uint32_t)25) /* 25 ms */
-#define HAL_TIMEOUT_TXIS ((uint32_t)25) /* 25 ms */
-#define MAX_NBYTE_SIZE 255
-/**
- * @}
- */
-
-/* Private macro -------------------------------------------------------------*/
-/** @defgroup SMBUS_Private_Macro SMBUS Private Macro
- * @{
- */
-#define __SMBUS_GET_ISR_REG(__HANDLE__) ((__HANDLE__)->Instance->ISR)
-#define __SMBUS_CHECK_FLAG(__ISR__, __FLAG__) ((((__ISR__) & ((__FLAG__) & SMBUS_FLAG_MASK)) == ((__FLAG__) & SMBUS_FLAG_MASK)))
-/**
- * @}
- */
-
-/* Private variables ---------------------------------------------------------*/
-/* Private function prototypes -----------------------------------------------*/
-/** @defgroup SMBUS_Private_Functions SMBUS Private Functions
- * @{
- */
-static HAL_StatusTypeDef SMBUS_WaitOnFlagUntilTimeout(SMBUS_HandleTypeDef *hsmbus, uint32_t Flag, FlagStatus Status, uint32_t Timeout);
-
-static HAL_StatusTypeDef SMBUS_Enable_IRQ(SMBUS_HandleTypeDef *hsmbus, uint16_t InterruptRequest);
-static HAL_StatusTypeDef SMBUS_Disable_IRQ(SMBUS_HandleTypeDef *hsmbus, uint16_t InterruptRequest);
-static HAL_StatusTypeDef SMBUS_Master_ISR(SMBUS_HandleTypeDef *hsmbus);
-static HAL_StatusTypeDef SMBUS_Slave_ISR(SMBUS_HandleTypeDef *hsmbus);
-
-static void SMBUS_TransferConfig(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t Size, uint32_t Mode, uint32_t Request);
-/**
- * @}
- */
-
-/* Exported functions ---------------------------------------------------------*/
-
-/** @defgroup SMBUS_Exported_Functions SMBUS Exported Functions
- * @{
- */
-
-/** @defgroup SMBUS_Exported_Functions_Group1 Initialization and de-initialization functions
- * @brief Initialization and Configuration functions
- *
-@verbatim
- ===============================================================================
- ##### Initialization and de-initialization functions #####
- ===============================================================================
- [..] This subsection provides a set of functions allowing to initialize and
- de-initialiaze the SMBUSx peripheral:
-
- (+) User must Implement HAL_SMBUS_MspInit() function in which he configures
- all related peripherals resources (CLOCK, GPIO, IT and NVIC ).
-
- (+) Call the function HAL_SMBUS_Init() to configure the selected device with
- the selected configuration:
- (++) Clock Timing
- (++) Bus Timeout
- (++) Analog Filer mode
- (++) Own Address 1
- (++) Addressing mode (Master, Slave)
- (++) Dual Addressing mode
- (++) Own Address 2
- (++) Own Address 2 Mask
- (++) General call mode
- (++) Nostretch mode
- (++) Packet Error Check mode
- (++) Peripheral mode
-
-
- (+) Call the function HAL_SMBUS_DeInit() to restore the default configuration
- of the selected SMBUSx periperal.
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Initializes the SMBUS according to the specified parameters
- * in the SMBUS_InitTypeDef and create the associated handle.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Init(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Check the SMBUS handle allocation */
- if(hsmbus == HAL_NULL)
- {
- return HAL_ERROR;
- }
-
- /* Check the parameters */
- assert_param(IS_SMBUS_ALL_INSTANCE(hsmbus->Instance));
- assert_param(IS_SMBUS_ANALOG_FILTER(hsmbus->Init.AnalogFilter));
- assert_param(IS_SMBUS_OWN_ADDRESS1(hsmbus->Init.OwnAddress1));
- assert_param(IS_SMBUS_ADDRESSING_MODE(hsmbus->Init.AddressingMode));
- assert_param(IS_SMBUS_DUAL_ADDRESS(hsmbus->Init.DualAddressMode));
- assert_param(IS_SMBUS_OWN_ADDRESS2(hsmbus->Init.OwnAddress2));
- assert_param(IS_SMBUS_OWN_ADDRESS2_MASK(hsmbus->Init.OwnAddress2Masks));
- assert_param(IS_SMBUS_GENERAL_CALL(hsmbus->Init.GeneralCallMode));
- assert_param(IS_SMBUS_NO_STRETCH(hsmbus->Init.NoStretchMode));
- assert_param(IS_SMBUS_PEC(hsmbus->Init.PacketErrorCheckMode));
- assert_param(IS_SMBUS_PERIPHERAL_MODE(hsmbus->Init.PeripheralMode));
-
- if(hsmbus->State == HAL_SMBUS_STATE_RESET)
- {
- /* Init the low level hardware : GPIO, CLOCK, NVIC */
- HAL_SMBUS_MspInit(hsmbus);
- }
-
- hsmbus->State = HAL_SMBUS_STATE_BUSY;
-
- /* Disable the selected SMBUS peripheral */
- __HAL_SMBUS_DISABLE(hsmbus);
-
- /*---------------------------- SMBUSx TIMINGR Configuration ------------------------*/
- /* Configure SMBUSx: Frequency range */
- hsmbus->Instance->TIMINGR = hsmbus->Init.Timing & TIMING_CLEAR_MASK;
-
- /*---------------------------- SMBUSx TIMEOUTR Configuration ------------------------*/
- /* Configure SMBUSx: Bus Timeout */
- hsmbus->Instance->TIMEOUTR &= ~I2C_TIMEOUTR_TIMOUTEN;
- hsmbus->Instance->TIMEOUTR &= ~I2C_TIMEOUTR_TEXTEN;
- hsmbus->Instance->TIMEOUTR = hsmbus->Init.SMBusTimeout;
-
- /*---------------------------- SMBUSx OAR1 Configuration -----------------------*/
- /* Configure SMBUSx: Own Address1 and ack own address1 mode */
- hsmbus->Instance->OAR1 &= ~I2C_OAR1_OA1EN;
-
- if(hsmbus->Init.OwnAddress1 != 0)
- {
- if(hsmbus->Init.AddressingMode == SMBUS_ADDRESSINGMODE_7BIT)
- {
- hsmbus->Instance->OAR1 = (I2C_OAR1_OA1EN | hsmbus->Init.OwnAddress1);
- }
- else /* SMBUS_ADDRESSINGMODE_10BIT */
- {
- hsmbus->Instance->OAR1 = (I2C_OAR1_OA1EN | I2C_OAR1_OA1MODE | hsmbus->Init.OwnAddress1);
- }
- }
-
- /*---------------------------- SMBUSx CR2 Configuration ------------------------*/
- /* Configure SMBUSx: Addressing Master mode */
- if(hsmbus->Init.AddressingMode == SMBUS_ADDRESSINGMODE_10BIT)
- {
- hsmbus->Instance->CR2 = (I2C_CR2_ADD10);
- }
- /* Enable the AUTOEND by default, and enable NACK (should be disable only during Slave process) */
- /* AUTOEND and NACK bit will be manage during Transfer process */
- hsmbus->Instance->CR2 |= (I2C_CR2_AUTOEND | I2C_CR2_NACK);
-
- /*---------------------------- SMBUSx OAR2 Configuration -----------------------*/
- /* Configure SMBUSx: Dual mode and Own Address2 */
- hsmbus->Instance->OAR2 = (hsmbus->Init.DualAddressMode | hsmbus->Init.OwnAddress2 | (hsmbus->Init.OwnAddress2Masks << 8));
-
- /*---------------------------- SMBUSx CR1 Configuration ------------------------*/
- /* Configure SMBUSx: Generalcall and NoStretch mode */
- hsmbus->Instance->CR1 = (hsmbus->Init.GeneralCallMode | hsmbus->Init.NoStretchMode | hsmbus->Init.PacketErrorCheckMode | hsmbus->Init.PeripheralMode | hsmbus->Init.AnalogFilter);
-
- /* Enable Slave Byte Control only in case of Packet Error Check is enabled and SMBUS Peripheral is set in Slave mode */
- if( (hsmbus->Init.PacketErrorCheckMode == SMBUS_PEC_ENABLED)
- && ( (hsmbus->Init.PeripheralMode == SMBUS_PERIPHERAL_MODE_SMBUS_SLAVE) || (hsmbus->Init.PeripheralMode == SMBUS_PERIPHERAL_MODE_SMBUS_SLAVE_ARP) ) )
- {
- hsmbus->Instance->CR1 |= I2C_CR1_SBC;
- }
-
- /* Enable the selected SMBUS peripheral */
- __HAL_SMBUS_ENABLE(hsmbus);
-
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
- hsmbus->PreviousState = HAL_SMBUS_STATE_READY;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- return HAL_OK;
-}
-
-/**
- * @brief DeInitializes the SMBUS peripheral.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_DeInit(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Check the SMBUS handle allocation */
- if(hsmbus == HAL_NULL)
- {
- return HAL_ERROR;
- }
-
- /* Check the parameters */
- assert_param(IS_SMBUS_ALL_INSTANCE(hsmbus->Instance));
-
- hsmbus->State = HAL_SMBUS_STATE_BUSY;
-
- /* Disable the SMBUS Peripheral Clock */
- __HAL_SMBUS_DISABLE(hsmbus);
-
- /* DeInit the low level hardware: GPIO, CLOCK, NVIC */
- HAL_SMBUS_MspDeInit(hsmbus);
-
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
- hsmbus->PreviousState = HAL_SMBUS_STATE_RESET;
- hsmbus->State = HAL_SMBUS_STATE_RESET;
-
- /* Release Lock */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_OK;
-}
-
-/**
- * @brief SMBUS MSP Init.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
- __weak void HAL_SMBUS_MspInit(SMBUS_HandleTypeDef *hsmbus)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_SMBUS_MspInit could be implemented in the user file
- */
-}
-
-/**
- * @brief SMBUS MSP DeInit
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
- __weak void HAL_SMBUS_MspDeInit(SMBUS_HandleTypeDef *hsmbus)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_SMBUS_MspDeInit could be implemented in the user file
- */
-}
-
-/**
- * @}
- */
-
-/** @defgroup SMBUS_Exported_Functions_Group2 Input and Output operation functions
- * @brief Data transfers functions
- *
-@verbatim
- ===============================================================================
- ##### IO operation functions #####
- ===============================================================================
- [..]
- This subsection provides a set of functions allowing to manage the SMBUS data
- transfers.
-
- (#) Blocking mode function to check if device is ready for usage is :
- (++) HAL_SMBUS_IsDeviceReady()
-
- (#) There is only one mode of transfer:
- (++) No-Blocking mode : The communication is performed using Interrupts.
- These functions return the status of the transfer startup.
- The end of the data processing will be indicated through the
- dedicated SMBUS IRQ when using Interrupt mode.
-
- (#) No-Blocking mode functions with Interrupt are :
- (++) HAL_SMBUS_Master_Transmit_IT()
- (++) HAL_SMBUS_Master_Receive_IT()
- (++) HAL_SMBUS_Slave_Transmit_IT()
- (++) HAL_SMBUS_Slave_Receive_IT()
- (++) HAL_SMBUS_Slave_Listen_IT() or alias HAL_SMBUS_EnableListen_IT()
- (++) HAL_SMBUS_DisableListen_IT()
- (++) HAL_SMBUS_EnableAlert_IT()
- (++) HAL_SMBUS_DisableAlert_IT()
-
- (#) A set of Transfer Complete Callbacks are provided in No_Blocking mode:
- (++) HAL_SMBUS_MasterTxCpltCallback()
- (++) HAL_SMBUS_MasterRxCpltCallback()
- (++) HAL_SMBUS_SlaveTxCpltCallback()
- (++) HAL_SMBUS_SlaveRxCpltCallback()
- (++) HAL_SMBUS_SlaveAddrCallback() or alias HAL_SMBUS_AddrCallback()
- (++) HAL_SMBUS_SlaveListenCpltCallback() or alias HAL_SMBUS_ListenCpltCallback()
- (++) HAL_SMBUS_ErrorCallback()
-
-@endverbatim
- * @{
- */
-
-/** @defgroup Non-Blocking_mode_Interrupt Non-Blocking mode Interrupt
- * @{
- */
-
-/**
- * @brief Transmit in master/host SMBUS mode an amount of data in no-blocking mode with Interrupt
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param DevAddress: Target device address
- * @param pData: Pointer to data buffer
- * @param Size: Amount of data to be sent
- * @param XferOptions: Options of Transfer, value of @ref SMBUS_XferOptions_definition
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Master_Transmit_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t XferOptions)
-{
- /* Check the parameters */
- assert_param(IS_SMBUS_TRANSFER_OPTIONS_REQUEST(XferOptions));
-
- if(hsmbus->State == HAL_SMBUS_STATE_READY)
- {
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- hsmbus->State = HAL_SMBUS_STATE_MASTER_BUSY_TX;
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
- /* Prepare transfer parameters */
- hsmbus->pBuffPtr = pData;
- hsmbus->XferCount = Size;
- hsmbus->XferOptions = XferOptions;
-
- /* In case of Quick command, remove autoend mode */
- /* Manage the stop generation by software */
- if(hsmbus->pBuffPtr == HAL_NULL)
- {
- hsmbus->XferOptions &= ~SMBUS_AUTOEND_MODE;
- }
-
- if(Size > MAX_NBYTE_SIZE)
- {
- hsmbus->XferSize = MAX_NBYTE_SIZE;
- }
- else
- {
- hsmbus->XferSize = Size;
- }
-
- /* Send Slave Address */
- /* Set NBYTES to write and reload if size > MAX_NBYTE_SIZE and generate RESTART */
- if( (hsmbus->XferSize == MAX_NBYTE_SIZE) && (hsmbus->XferSize < hsmbus->XferCount) )
- {
- SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_GENERATE_START_WRITE);
- }
- else
- {
- /* If transfer direction not change, do not generate Restart Condition */
- /* Mean Previous state is same as current state */
- if(hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
- }
- /* Else transfer direction change, so generate Restart with new transfer direction */
- else
- {
- SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_GENERATE_START_WRITE);
- }
-
- /* If PEC mode is enable, size to transmit manage by SW part should be Size-1 byte, corresponding to PEC byte */
- /* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */
- if(__HAL_SMBUS_GET_PEC_MODE(hsmbus) != RESET)
- {
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- }
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Note : The SMBUS interrupts must be enabled after unlocking current process
- to avoid the risk of SMBUS interrupt handle execution before current
- process unlock */
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_TX);
-
- return HAL_OK;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-
-/**
- * @brief Receive in master/host SMBUS mode an amount of data in no-blocking mode with Interrupt
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param DevAddress: Target device address
- * @param pData: Pointer to data buffer
- * @param Size: Amount of data to be sent
- * @param XferOptions: Options of Transfer, value of @ref SMBUS_XferOptions_definition
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Master_Receive_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t XferOptions)
-{
- /* Check the parameters */
- assert_param(IS_SMBUS_TRANSFER_OPTIONS_REQUEST(XferOptions));
-
- if(hsmbus->State == HAL_SMBUS_STATE_READY)
- {
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- hsmbus->State = HAL_SMBUS_STATE_MASTER_BUSY_RX;
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
-
- /* Prepare transfer parameters */
- hsmbus->pBuffPtr = pData;
- hsmbus->XferCount = Size;
- hsmbus->XferOptions = XferOptions;
-
- /* In case of Quick command, remove autoend mode */
- /* Manage the stop generation by software */
- if(hsmbus->pBuffPtr == HAL_NULL)
- {
- hsmbus->XferOptions &= ~SMBUS_AUTOEND_MODE;
- }
-
- if(Size > MAX_NBYTE_SIZE)
- {
- hsmbus->XferSize = MAX_NBYTE_SIZE;
- }
- else
- {
- hsmbus->XferSize = Size;
- }
-
- /* Send Slave Address */
- /* Set NBYTES to write and reload if size > MAX_NBYTE_SIZE and generate RESTART */
- if( (hsmbus->XferSize == MAX_NBYTE_SIZE) && (hsmbus->XferSize < hsmbus->XferCount) )
- {
- SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_GENERATE_START_READ);
- }
- else
- {
- /* If transfer direction not change, do not generate Restart Condition */
- /* Mean Previous state is same as current state */
- if(hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
- }
- /* Else transfer direction change, so generate Restart with new transfer direction */
- else
- {
- SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_GENERATE_START_READ);
- }
- }
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Note : The SMBUS interrupts must be enabled after unlocking current process
- to avoid the risk of SMBUS interrupt handle execution before current
- process unlock */
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_RX);
-
- return HAL_OK;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-
-/**
- * @brief Abort a master/host SMBUS process commnunication with Interrupt
- * @note : This abort can be called only if state is ready
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param DevAddress: Target device address
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Master_Abort_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress)
-{
- if(hsmbus->State == HAL_SMBUS_STATE_READY)
- {
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- /* Keep the same state as previous */
- /* to perform as well the call of the corresponding end of transfer callback */
- if(hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- hsmbus->State = HAL_SMBUS_STATE_MASTER_BUSY_TX;
- }
- else if(hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- hsmbus->State = HAL_SMBUS_STATE_MASTER_BUSY_RX;
- }
- else
- {
- /* Wrong usage of abort function */
- /* This function should be used only in case of abort monitored by master device */
- return HAL_ERROR;
- }
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
-
- /* Set NBYTES to 1 to generate a dummy read on SMBUS peripheral */
- /* Set AUTOEND mode, this will generate a NACK then STOP condition to abort the current transfer */
- SMBUS_TransferConfig(hsmbus, DevAddress, 1, SMBUS_AUTOEND_MODE, SMBUS_NO_STARTSTOP);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Note : The SMBUS interrupts must be enabled after unlocking current process
- to avoid the risk of SMBUS interrupt handle execution before current
- process unlock */
- if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_TX);
- }
- else if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_RX);
- }
-
- return HAL_OK;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-
-/**
- * @brief Transmit in slave/device SMBUS mode an amount of data in no-blocking mode with Interrupt
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param pData: Pointer to data buffer
- * @param Size: Amount of data to be sent
- * @param XferOptions: Options of Transfer, value of @ref SMBUS_XferOptions_definition
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Slave_Transmit_IT(SMBUS_HandleTypeDef *hsmbus, uint8_t *pData, uint16_t Size, uint32_t XferOptions)
-{
- /* Check the parameters */
- assert_param(IS_SMBUS_TRANSFER_OPTIONS_REQUEST(XferOptions));
-
- if(hsmbus->State == HAL_SMBUS_STATE_LISTEN)
- {
- if((pData == HAL_NULL) || (Size == 0))
- {
- return HAL_ERROR;
- }
-
- /* Disable Interrupts, to prevent preemption during treatment in case of multicall */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ADDR | SMBUS_IT_TX);
-
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- hsmbus->State |= HAL_SMBUS_STATE_SLAVE_BUSY_TX;
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
-
- /* Set SBC bit to manage Acknowledge at each bit */
- hsmbus->Instance->CR1 |= I2C_CR1_SBC;
-
- /* Enable Address Acknowledge */
- hsmbus->Instance->CR2 &= ~I2C_CR2_NACK;
-
- /* Prepare transfer parameters */
- hsmbus->pBuffPtr = pData;
- hsmbus->XferSize = Size;
- hsmbus->XferCount = Size;
- hsmbus->XferOptions = XferOptions;
-
- if(Size > MAX_NBYTE_SIZE)
- {
- hsmbus->XferSize = MAX_NBYTE_SIZE;
- }
- else
- {
- hsmbus->XferSize = Size;
- }
-
- /* Set NBYTES to write and reload if size > MAX_NBYTE_SIZE and generate RESTART */
- if( (hsmbus->XferSize == MAX_NBYTE_SIZE) && (hsmbus->XferSize < hsmbus->XferCount) )
- {
- SMBUS_TransferConfig(hsmbus,0,hsmbus->XferSize, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_NO_STARTSTOP);
- }
- else
- {
- /* Set NBYTE to transmit */
- SMBUS_TransferConfig(hsmbus,0,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
-
- /* If PEC mode is enable, size to transmit should be Size-1 byte, corresponding to PEC byte */
- /* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */
- if(__HAL_SMBUS_GET_PEC_MODE(hsmbus) != RESET)
- {
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- }
-
- /* Clear ADDR flag after prepare the transfer parameters */
- /* This action will generate an acknowledge to the HOST */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus,SMBUS_FLAG_ADDR);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Note : The SMBUS interrupts must be enabled after unlocking current process
- to avoid the risk of SMBUS interrupt handle execution before current
- process unlock */
- /* REnable ADDR interrupt */
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_TX | SMBUS_IT_ADDR);
-
- return HAL_OK;
- }
- else
- {
- return HAL_ERROR;
- }
-}
-
-/**
- * @brief Receive in slave/device SMBUS mode an amount of data in no-blocking mode with Interrupt
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param pData: Pointer to data buffer
- * @param Size: Amount of data to be sent
- * @param XferOptions: Options of Transfer, value of @ref SMBUS_XferOptions_definition
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Slave_Receive_IT(SMBUS_HandleTypeDef *hsmbus, uint8_t *pData, uint16_t Size, uint32_t XferOptions)
-{
- /* Check the parameters */
- assert_param(IS_SMBUS_TRANSFER_OPTIONS_REQUEST(XferOptions));
-
- if(hsmbus->State == HAL_SMBUS_STATE_LISTEN)
- {
- if((pData == HAL_NULL) || (Size == 0))
- {
- return HAL_ERROR;
- }
-
- /* Disable Interrupts, to prevent preemption during treatment in case of multicall */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ADDR | SMBUS_IT_RX);
-
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- hsmbus->State |= HAL_SMBUS_STATE_SLAVE_BUSY_RX;
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
-
- /* Set SBC bit to manage Acknowledge at each bit */
- hsmbus->Instance->CR1 |= I2C_CR1_SBC;
-
- /* Enable Address Acknowledge */
- hsmbus->Instance->CR2 &= ~I2C_CR2_NACK;
-
- /* Prepare transfer parameters */
- hsmbus->pBuffPtr = pData;
- hsmbus->XferSize = Size;
- hsmbus->XferCount = Size;
- hsmbus->XferOptions = XferOptions;
-
- /* Set NBYTE to receive */
- /* If XferSize equal "1", or XferSize equal "2" with PEC requested (mean 1 data byte + 1 PEC byte */
- /* no need to set RELOAD bit mode, a ACK will be automatically generated in that case */
- /* else need to set RELOAD bit mode to generate an automatic ACK at each byte Received */
- /* This RELOAD bit will be reset for last BYTE to be receive in SMBUS_Slave_ISR */
- if((hsmbus->XferSize == 1) || ((hsmbus->XferSize == 2) && (__HAL_SMBUS_GET_PEC_MODE(hsmbus) != RESET)))
- {
- SMBUS_TransferConfig(hsmbus,0,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
- }
- else
- {
- SMBUS_TransferConfig(hsmbus,0, 1, hsmbus->XferOptions | SMBUS_RELOAD_MODE, SMBUS_NO_STARTSTOP);
- }
-
- /* Clear ADDR flag after prepare the transfer parameters */
- /* This action will generate an acknowledge to the HOST */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus,SMBUS_FLAG_ADDR);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Note : The SMBUS interrupts must be enabled after unlocking current process
- to avoid the risk of SMBUS interrupt handle execution before current
- process unlock */
- /* REnable ADDR interrupt */
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_RX | SMBUS_IT_ADDR);
-
- return HAL_OK;
- }
- else
- {
- return HAL_ERROR;
- }
-}
-
-/**
- * @brief This function enable the Address listen mode
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Slave_Listen_IT(SMBUS_HandleTypeDef *hsmbus)
-{
- hsmbus->State = HAL_SMBUS_STATE_LISTEN;
-
- /* Enable the Address Match interrupt */
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_ADDR);
-
- return HAL_OK;
-}
-
-/**
- * @brief This function disable the Address listen mode
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_DisableListen_IT(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Disable Address listen mode only if a transfer is not ongoing */
- if(hsmbus->State == HAL_SMBUS_STATE_LISTEN)
- {
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Disable the Address Match interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ADDR);
-
- return HAL_OK;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-
-/**
- * @brief This function enable the SMBUS alert mode.
- * @param hsmbus : pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUSx peripheral.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_EnableAlert_IT(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Enable SMBus alert */
- hsmbus->Instance->CR1 |= I2C_CR1_ALERTEN;
-
- /* Clear ALERT flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_ALERT);
-
- /* Enable Alert Interrupt */
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_ALERT);
-
- return HAL_OK;
-}
-/**
- * @brief This function disable the SMBUS alert mode.
- * @param hsmbus : pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUSx peripheral.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_DisableAlert_IT(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Enable SMBus alert */
- hsmbus->Instance->CR1 &= ~I2C_CR1_ALERTEN;
-
- /* Disable Alert Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ALERT);
-
- return HAL_OK;
-}
-
-/**
- * @}
- */
-
-/** @defgroup Blocking_mode_Polling Blocking mode Polling
- * @{
- */
-/**
- * @brief Checks if target device is ready for communication.
- * @note This function is used with Memory devices
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param DevAddress: Target device address
- * @param Trials: Number of trials
- * @param Timeout: Timeout duration
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_IsDeviceReady(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint32_t Trials, uint32_t Timeout)
-{
- uint32_t tickstart = 0;
-
- __IO uint32_t SMBUS_Trials = 0;
-
- if(hsmbus->State == HAL_SMBUS_STATE_READY)
- {
- if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_BUSY) != RESET)
- {
- return HAL_BUSY;
- }
-
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- hsmbus->State = HAL_SMBUS_STATE_BUSY;
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
-
- do
- {
- /* Generate Start */
- hsmbus->Instance->CR2 = __HAL_SMBUS_GENERATE_START(hsmbus->Init.AddressingMode,DevAddress);
-
- /* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */
- /* Wait until STOPF flag is set or a NACK flag is set*/
- tickstart = HAL_GetTick();
- while((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_STOPF) == RESET) && (__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_AF) == RESET) && (hsmbus->State != HAL_SMBUS_STATE_TIMEOUT))
- {
- if(Timeout != HAL_MAX_DELAY)
- {
- if((Timeout == 0) || ((HAL_GetTick()-tickstart) > Timeout))
- {
- /* Device is ready */
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
- return HAL_TIMEOUT;
- }
- }
- }
-
- /* Check if the NACKF flag has not been set */
- if (__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_AF) == RESET)
- {
- /* Wait until STOPF flag is reset */
- if(SMBUS_WaitOnFlagUntilTimeout(hsmbus, SMBUS_FLAG_STOPF, RESET, Timeout) != HAL_OK)
- {
- return HAL_TIMEOUT;
- }
-
- /* Clear STOP Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF);
-
- /* Device is ready */
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_OK;
- }
- else
- {
- /* Wait until STOPF flag is reset */
- if(SMBUS_WaitOnFlagUntilTimeout(hsmbus, SMBUS_FLAG_STOPF, RESET, Timeout) != HAL_OK)
- {
- return HAL_TIMEOUT;
- }
-
- /* Clear NACK Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_AF);
-
- /* Clear STOP Flag, auto generated with autoend*/
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF);
- }
-
- /* Check if the maximum allowed number of trials has been reached */
- if (SMBUS_Trials++ == Trials)
- {
- /* Generate Stop */
- hsmbus->Instance->CR2 |= I2C_CR2_STOP;
-
- /* Wait until STOPF flag is reset */
- if(SMBUS_WaitOnFlagUntilTimeout(hsmbus, SMBUS_FLAG_STOPF, RESET, Timeout) != HAL_OK)
- {
- return HAL_TIMEOUT;
- }
-
- /* Clear STOP Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF);
- }
- }while(SMBUS_Trials < Trials);
-
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_TIMEOUT;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-/**
- * @}
- */
-
-/** @defgroup IRQ_Handler_and_Callbacks IRQ Handler and Callbacks
- * @{
- */
-
-/**
- * @brief This function handles SMBUS event interrupt request.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-void HAL_SMBUS_EV_IRQHandler(SMBUS_HandleTypeDef *hsmbus)
-{
- uint32_t tmpisrvalue = 0;
-
- /* Use a local variable to store the current ISR flags */
- /* This action will avoid a wrong treatment due to ISR flags change during interrupt handler */
- tmpisrvalue = __SMBUS_GET_ISR_REG(hsmbus);
-
- /* SMBUS in mode Transmitter ---------------------------------------------------*/
- if (((__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TXIS) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TCR) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TC) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_STOPF) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_AF) != RESET)) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, (SMBUS_IT_TCI| SMBUS_IT_STOPI| SMBUS_IT_NACKI | SMBUS_IT_TXI)) != RESET))
- {
- /* Slave mode selected */
- if ((hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_TX) == HAL_SMBUS_STATE_SLAVE_BUSY_TX)
- {
- SMBUS_Slave_ISR(hsmbus);
- }
- /* Master mode selected */
- else if((hsmbus->State & HAL_SMBUS_STATE_MASTER_BUSY_TX) == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- SMBUS_Master_ISR(hsmbus);
- }
- }
-
- /* SMBUS in mode Receiver ----------------------------------------------------*/
- if (((__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_RXNE) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TCR) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TC) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_STOPF) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_AF) != RESET)) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, (SMBUS_IT_TCI| SMBUS_IT_STOPI| SMBUS_IT_NACKI | SMBUS_IT_RXI)) != RESET))
- {
- /* Slave mode selected */
- if ((hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_RX) == HAL_SMBUS_STATE_SLAVE_BUSY_RX)
- {
- SMBUS_Slave_ISR(hsmbus);
- }
- /* Master mode selected */
- else if((hsmbus->State & HAL_SMBUS_STATE_MASTER_BUSY_RX) == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- SMBUS_Master_ISR(hsmbus);
- }
- }
-
- /* SMBUS in mode Listener Only --------------------------------------------------*/
- if (((__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_ADDR) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_STOPF) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_AF) != RESET))
- && ((__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ADDRI) != RESET) || (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_STOPI) != RESET) || (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_NACKI) != RESET)))
- {
- if (hsmbus->State == HAL_SMBUS_STATE_LISTEN)
- {
- SMBUS_Slave_ISR(hsmbus);
- }
- }
-}
-
-/**
- * @brief This function handles SMBUS error interrupt request.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-void HAL_SMBUS_ER_IRQHandler(SMBUS_HandleTypeDef *hsmbus)
-{
- /* SMBUS Bus error interrupt occurred ------------------------------------*/
- if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_BERR) != RESET) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ERRI) != RESET))
- {
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_BERR;
-
- /* Clear BERR flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_BERR);
- }
-
- /* SMBUS Over-Run/Under-Run interrupt occurred ----------------------------------------*/
- if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_OVR) != RESET) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ERRI) != RESET))
- {
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_OVR;
-
- /* Clear OVR flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_OVR);
- }
-
- /* SMBUS Arbitration Loss error interrupt occurred ------------------------------------*/
- if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_ARLO) != RESET) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ERRI) != RESET))
- {
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ARLO;
-
- /* Clear ARLO flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_ARLO);
- }
-
- /* SMBUS Timeout error interrupt occurred ---------------------------------------------*/
- if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_TIMEOUT) != RESET) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ERRI) != RESET))
- {
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_BUSTIMEOUT;
-
- /* Clear TIMEOUT flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_TIMEOUT);
- }
-
- /* SMBUS Alert error interrupt occurred -----------------------------------------------*/
- if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_ALERT) != RESET) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ERRI) != RESET))
- {
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ALERT;
-
- /* Clear ALERT flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_ALERT);
- }
-
- /* SMBUS Packet Error Check error interrupt occurred ----------------------------------*/
- if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_PECERR) != RESET) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ERRI) != RESET))
- {
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_PECERR;
-
- /* Clear PEC error flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_PECERR);
- }
-
- /* Call the Error Callback in case of Error detected */
- if((hsmbus->ErrorCode != HAL_SMBUS_ERROR_NONE)&&(hsmbus->ErrorCode != HAL_SMBUS_ERROR_ACKF))
- {
- /* Do not Reset the the HAL state in case of ALERT error */
- if((hsmbus->ErrorCode & HAL_SMBUS_ERROR_ALERT) != HAL_SMBUS_ERROR_ALERT)
- {
- if(((hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_TX) == HAL_SMBUS_STATE_SLAVE_BUSY_TX)
- || ((hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_RX) == HAL_SMBUS_STATE_SLAVE_BUSY_RX))
- {
- /* Reset only HAL_SMBUS_STATE_SLAVE_BUSY_XX */
- /* keep HAL_SMBUS_STATE_LISTEN if set */
- hsmbus->PreviousState = HAL_SMBUS_STATE_READY;
- hsmbus->State = HAL_SMBUS_STATE_LISTEN;
- }
- }
-
- /* Call the Error callback to prevent upper layer */
- HAL_SMBUS_ErrorCallback(hsmbus);
- }
-}
-
-/**
- * @brief Master Tx Transfer completed callbacks.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
- __weak void HAL_SMBUS_MasterTxCpltCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_SMBUS_TxCpltCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Master Rx Transfer completed callbacks.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-__weak void HAL_SMBUS_MasterRxCpltCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_SMBUS_TxCpltCallback could be implemented in the user file
- */
-}
-
-/** @brief Slave Tx Transfer completed callbacks.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
- __weak void HAL_SMBUS_SlaveTxCpltCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_SMBUS_TxCpltCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Slave Rx Transfer completed callbacks.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-__weak void HAL_SMBUS_SlaveRxCpltCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_SMBUS_TxCpltCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Slave Address Match callbacks.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param TransferDirection: Master request Transfer Direction (Write/Read)
- * @param AddrMatchCode: Address Match Code
- * @retval None
- */
-__weak void HAL_SMBUS_SlaveAddrCallback(SMBUS_HandleTypeDef *hsmbus, uint8_t TransferDirection, uint16_t AddrMatchCode)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_SMBUS_SlaveAddrCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Listen Complete callbacks.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-__weak void HAL_SMBUS_SlaveListenCpltCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_SMBUS_SlaveListenCpltCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief SMBUS error callbacks.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
- __weak void HAL_SMBUS_ErrorCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_SMBUS_ErrorCallback could be implemented in the user file
- */
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/** @defgroup SMBUS_Exported_Functions_Group3 Peripheral State and Errors functions
- * @brief Peripheral State and Errors functions
- *
-@verbatim
- ===============================================================================
- ##### Peripheral State and Errors functions #####
- ===============================================================================
- [..]
- This subsection permit to get in run-time the status of the peripheral
- and the data flow.
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Returns the SMBUS state.
- * @param hsmbus : SMBUS handle
- * @retval HAL state
- */
-HAL_SMBUS_StateTypeDef HAL_SMBUS_GetState(SMBUS_HandleTypeDef *hsmbus)
-{
- return hsmbus->State;
-}
-
-/**
-* @brief Return the SMBUS error code
-* @param hsmbus : pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
-* @retval SMBUS Error Code
-*/
-uint32_t HAL_SMBUS_GetError(SMBUS_HandleTypeDef *hsmbus)
-{
- return hsmbus->ErrorCode;
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/** @addtogroup SMBUS_Private_Functions SMBUS Private Functions
- * @brief Data transfers Private functions
- * @{
- */
-
-/**
- * @brief Interrupt Sub-Routine which handle the Interrupt Flags Master Mode
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval HAL status
- */
-static HAL_StatusTypeDef SMBUS_Master_ISR(SMBUS_HandleTypeDef *hsmbus)
-{
- uint16_t DevAddress;
-
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_AF) != RESET)
- {
- /* Clear NACK Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_AF);
-
- /* Set corresponding Error Code */
- /* No need to generate STOP, it is automatically done */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ACKF;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the Error callback to prevent upper layer */
- HAL_SMBUS_ErrorCallback(hsmbus);
- }
- else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_STOPF) != RESET)
- {
-
- /* Call the corresponding callback to inform upper layer of End of Transfer */
- if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- /* Disable Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_TX);
-
- /* Clear STOP Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF);
-
- /* Clear Configuration Register 2 */
- __HAL_SMBUS_RESET_CR2(hsmbus);
-
- /* Flush remaining data in Fifo register in case of error occurs before TXEmpty */
- /* Disable the selected SMBUS peripheral */
- __HAL_SMBUS_DISABLE(hsmbus);
-
- hsmbus->PreviousState = HAL_SMBUS_STATE_READY;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* REenable the selected SMBUS peripheral */
- __HAL_SMBUS_ENABLE(hsmbus);
-
- HAL_SMBUS_MasterTxCpltCallback(hsmbus);
- }
- else if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- /* Disable Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX);
-
- /* Clear STOP Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF);
-
- /* Clear Configuration Register 2 */
- __HAL_SMBUS_RESET_CR2(hsmbus);
-
- hsmbus->PreviousState = HAL_SMBUS_STATE_READY;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- HAL_SMBUS_MasterRxCpltCallback(hsmbus);
- }
- }
- else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_RXNE) != RESET)
- {
- /* Read data from RXDR */
- (*hsmbus->pBuffPtr++) = hsmbus->Instance->RXDR;
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_TXIS) != RESET)
- {
- /* Write data to TXDR */
- hsmbus->Instance->TXDR = (*hsmbus->pBuffPtr++);
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_TCR) != RESET)
- {
- if((hsmbus->XferSize == 0)&&(hsmbus->XferCount!=0))
- {
- DevAddress = (hsmbus->Instance->CR2 & I2C_CR2_SADD);
-
- if(hsmbus->XferCount > MAX_NBYTE_SIZE)
- {
- SMBUS_TransferConfig(hsmbus, DevAddress, MAX_NBYTE_SIZE, (SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE)), SMBUS_NO_STARTSTOP);
- hsmbus->XferSize = MAX_NBYTE_SIZE;
- }
- else
- {
- hsmbus->XferSize = hsmbus->XferCount;
- SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
- /* If PEC mode is enable, size to transmit should be Size-1 byte, corresponding to PEC byte */
- /* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */
- if(__HAL_SMBUS_GET_PEC_MODE(hsmbus) != RESET)
- {
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- }
- }
- else if((hsmbus->XferSize == 0)&&(hsmbus->XferCount==0))
- {
- /* Call TxCpltCallback if no stop mode is set */
- if(__HAL_SMBUS_GET_STOP_MODE(hsmbus) != SMBUS_AUTOEND_MODE)
- {
- /* Call the corresponding callback to inform upper layer of End of Transfer */
- if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- /* Disable Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_TX);
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- HAL_SMBUS_MasterTxCpltCallback(hsmbus);
- }
- else if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX);
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- HAL_SMBUS_MasterRxCpltCallback(hsmbus);
- }
- }
- }
- }
- else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_TC) != RESET)
- {
- if(hsmbus->XferCount == 0)
- {
- /* Specific use case for Quick command */
- if(hsmbus->pBuffPtr == HAL_NULL)
- {
- /* Generate a Stop command */
- hsmbus->Instance->CR2 |= I2C_CR2_STOP;
- }
- /* Call TxCpltCallback if no stop mode is set */
- else if(__HAL_SMBUS_GET_STOP_MODE(hsmbus) != SMBUS_AUTOEND_MODE)
- {
- /* No Generate Stop, to permit restart mode */
- /* The stop will be done at the end of transfer, when SMBUS_AUTOEND_MODE enable */
-
- /* Call the corresponding callback to inform upper layer of End of Transfer */
- if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- /* Disable Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_TX);
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- HAL_SMBUS_MasterTxCpltCallback(hsmbus);
- }
- else if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX);
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- HAL_SMBUS_MasterRxCpltCallback(hsmbus);
- }
- }
- }
- }
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_OK;
-}
-/**
- * @brief Interrupt Sub-Routine which handle the Interrupt Flags Slave Mode
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval HAL status
- */
-static HAL_StatusTypeDef SMBUS_Slave_ISR(SMBUS_HandleTypeDef *hsmbus)
-{
- uint8_t TransferDirection = 0;
- uint16_t SlaveAddrCode = 0;
-
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_AF) != RESET)
- {
- /* Check that SMBUS transfer finished */
- /* if yes, normal usecase, a NACK is sent by the HOST when Transfer is finished */
- /* Mean XferCount == 0*/
- /* So clear Flag NACKF only */
- if(hsmbus->XferCount == 0)
- {
- /* Clear NACK Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_AF);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
- }
- else
- {
- /* if no, error usecase, a Non-Acknowledge of last Data is generated by the HOST*/
- /* Clear NACK Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_AF);
-
- /* Set HAL State to "Idle" State, mean to LISTEN state */
- /* So reset Slave Busy state */
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State &= ~((uint32_t)HAL_SMBUS_STATE_SLAVE_BUSY_TX);
- hsmbus->State &= ~((uint32_t)HAL_SMBUS_STATE_SLAVE_BUSY_RX);
-
- /* Disable RX/TX Interrupts, keep only ADDR Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX | SMBUS_IT_TX);
-
- /* Set ErrorCode corresponding to a Non-Acknowledge */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ACKF;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the Error callback to prevent upper layer */
- HAL_SMBUS_ErrorCallback(hsmbus);
- }
- }
- else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_ADDR) != RESET)
- {
- TransferDirection = __HAL_SMBUS_GET_DIR(hsmbus);
- SlaveAddrCode = __HAL_SMBUS_GET_ADDR_MATCH(hsmbus);
-
- /* Disable ADDR interrupt to prevent multiple ADDRInterrupt*/
- /* Other ADDRInterrupt will be treat in next Listen usecase */
- __HAL_SMBUS_DISABLE_IT(hsmbus, SMBUS_IT_ADDRI);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call Slave Addr callback */
- HAL_SMBUS_SlaveAddrCallback(hsmbus, TransferDirection, SlaveAddrCode);
- }
- else if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_RXNE) != RESET) || (__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_TCR) != RESET))
- {
- if( (hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_RX) == HAL_SMBUS_STATE_SLAVE_BUSY_RX)
- {
- /* Read data from RXDR */
- (*hsmbus->pBuffPtr++) = hsmbus->Instance->RXDR;
- hsmbus->XferSize--;
- hsmbus->XferCount--;
-
- if(hsmbus->XferCount == 1)
- {
- /* Receive last Byte, can be PEC byte in case of PEC BYTE enabled */
- /* or only the last Byte of Transfer */
- /* So reset the RELOAD bit mode */
- hsmbus->XferOptions &= ~SMBUS_RELOAD_MODE;
- SMBUS_TransferConfig(hsmbus,0 ,1 , hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
- }
- else if(hsmbus->XferCount == 0)
- {
- /* Last Byte is received, disable Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX);
-
- /* Remove HAL_SMBUS_STATE_SLAVE_BUSY_RX, keep only HAL_SMBUS_STATE_LISTEN */
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State &= ~((uint32_t)HAL_SMBUS_STATE_SLAVE_BUSY_RX);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the Rx complete callback to inform upper layer of the end of receive process */
- HAL_SMBUS_SlaveRxCpltCallback(hsmbus);
- }
- else
- {
- /* Set Reload for next Bytes */
- SMBUS_TransferConfig(hsmbus,0, 1, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_NO_STARTSTOP);
-
- /* Ack last Byte Read */
- hsmbus->Instance->CR2 &= ~I2C_CR2_NACK;
- }
- }
- else if( (hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_TX) == HAL_SMBUS_STATE_SLAVE_BUSY_TX)
- {
- if((hsmbus->XferSize == 0)&&(hsmbus->XferCount!=0))
- {
- if(hsmbus->XferCount > MAX_NBYTE_SIZE)
- {
- SMBUS_TransferConfig(hsmbus, 0, MAX_NBYTE_SIZE, (SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE)), SMBUS_NO_STARTSTOP);
- hsmbus->XferSize = MAX_NBYTE_SIZE;
- }
- else
- {
- hsmbus->XferSize = hsmbus->XferCount;
- SMBUS_TransferConfig(hsmbus, 0, hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
- /* If PEC mode is enable, size to transmit should be Size-1 byte, corresponding to PEC byte */
- /* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */
- if(__HAL_SMBUS_GET_PEC_MODE(hsmbus) != RESET)
- {
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- }
- }
- }
- }
- else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_TXIS) != RESET)
- {
- /* Write data to TXDR only if XferCount not reach "0" */
- /* A TXIS flag can be set, during STOP treatment */
- /* Check if all Datas have already been sent */
- /* If it is the case, this last write in TXDR is not sent, correspond to a dummy TXIS event */
- if(hsmbus->XferCount > 0)
- {
- /* Write data to TXDR */
- hsmbus->Instance->TXDR = (*hsmbus->pBuffPtr++);
- hsmbus->XferCount--;
- hsmbus->XferSize--;
- }
-
- if(hsmbus->XferCount == 0)
- {
- /* Last Byte is Transmitted */
- /* Remove HAL_SMBUS_STATE_SLAVE_BUSY_TX, keep only HAL_SMBUS_STATE_LISTEN */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_TX);
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State &= ~((uint32_t)HAL_SMBUS_STATE_SLAVE_BUSY_TX);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the Tx complete callback to inform upper layer of the end of transmit process */
- HAL_SMBUS_SlaveTxCpltCallback(hsmbus);
- }
- }
-
- /* Check if STOPF is set */
- if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_STOPF) != RESET)
- {
- if((hsmbus->State & HAL_SMBUS_STATE_LISTEN) == HAL_SMBUS_STATE_LISTEN)
- {
- /* Disable RX and TX Interrupts */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX | SMBUS_IT_TX);
-
- /* Disable ADDR Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ADDR);
-
- /* Disable Address Acknowledge */
- hsmbus->Instance->CR2 |= I2C_CR2_NACK;
-
- /* Clear Configuration Register 2 */
- __HAL_SMBUS_RESET_CR2(hsmbus);
-
- /* Clear STOP Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF);
-
- /* Clear ADDR flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus,SMBUS_FLAG_ADDR);
-
- hsmbus->XferOptions = 0;
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the Listen Complete callback, to prevent upper layer of the end of Listen usecase */
- HAL_SMBUS_SlaveListenCpltCallback(hsmbus);
- }
- }
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_OK;
-}
-/**
- * @brief Manage the enabling of Interrupts
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param InterruptRequest : Value of @ref SMBUS_Interrupt_configuration_definition.
- * @retval HAL status
- */
-static HAL_StatusTypeDef SMBUS_Enable_IRQ(SMBUS_HandleTypeDef *hsmbus, uint16_t InterruptRequest)
-{
- uint32_t tmpisr = 0;
-
- if((InterruptRequest & SMBUS_IT_ALERT) == SMBUS_IT_ALERT)
- {
- /* Enable ERR interrupt */
- tmpisr |= SMBUS_IT_ERRI;
- }
-
- if((InterruptRequest & SMBUS_IT_ADDR) == SMBUS_IT_ADDR)
- {
- /* Enable ADDR, STOP interrupt */
- tmpisr |= SMBUS_IT_ADDRI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_ERRI;
- }
-
- if((InterruptRequest & SMBUS_IT_TX) == SMBUS_IT_TX)
- {
- /* Enable ERR, TC, STOP, NACK, RXI interrupt */
- tmpisr |= SMBUS_IT_ERRI | SMBUS_IT_TCI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_TXI;
- }
-
- if((InterruptRequest & SMBUS_IT_RX) == SMBUS_IT_RX)
- {
- /* Enable ERR, TC, STOP, NACK, TXI interrupt */
- tmpisr |= SMBUS_IT_ERRI | SMBUS_IT_TCI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_RXI;
- }
-
- /* Enable interrupts only at the end */
- /* to avoid the risk of SMBUS interrupt handle execution before */
- /* all interrupts requested done */
- __HAL_SMBUS_ENABLE_IT(hsmbus, tmpisr);
-
- return HAL_OK;
-}
-/**
- * @brief Manage the disabling of Interrupts
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param InterruptRequest : Value of @ref SMBUS_Interrupt_configuration_definition.
- * @retval HAL status
- */
-static HAL_StatusTypeDef SMBUS_Disable_IRQ(SMBUS_HandleTypeDef *hsmbus, uint16_t InterruptRequest)
-{
- uint32_t tmpisr = 0;
-
- if( ((InterruptRequest & SMBUS_IT_ALERT) == SMBUS_IT_ALERT) && (hsmbus->State == HAL_SMBUS_STATE_READY) )
- {
- /* Disable ERR interrupt */
- tmpisr |= SMBUS_IT_ERRI;
- }
-
- if((InterruptRequest & SMBUS_IT_TX) == SMBUS_IT_TX)
- {
- /* Disable TC, STOP, NACK, TXI interrupt */
- tmpisr |= SMBUS_IT_TCI | SMBUS_IT_TXI;
-
- if((__HAL_SMBUS_GET_ALERT_ENABLED(hsmbus) == RESET)
- && ((hsmbus->State & HAL_SMBUS_STATE_LISTEN) != HAL_SMBUS_STATE_LISTEN))
- {
- /* Disable ERR interrupt */
- tmpisr |= SMBUS_IT_ERRI;
- }
-
- if((hsmbus->State & HAL_SMBUS_STATE_LISTEN) != HAL_SMBUS_STATE_LISTEN)
- {
- /* Disable STOPI, NACKI */
- tmpisr |= SMBUS_IT_STOPI | SMBUS_IT_NACKI;
- }
- }
-
- if((InterruptRequest & SMBUS_IT_RX) == SMBUS_IT_RX)
- {
- /* Disable TC, STOP, NACK, RXI interrupt */
- tmpisr |= SMBUS_IT_TCI | SMBUS_IT_RXI;
-
- if((__HAL_SMBUS_GET_ALERT_ENABLED(hsmbus) == RESET)
- && ((hsmbus->State & HAL_SMBUS_STATE_LISTEN) != HAL_SMBUS_STATE_LISTEN))
- {
- /* Disable ERR interrupt */
- tmpisr |= SMBUS_IT_ERRI;
- }
-
- if((hsmbus->State & HAL_SMBUS_STATE_LISTEN) != HAL_SMBUS_STATE_LISTEN)
- {
- /* Disable STOPI, NACKI */
- tmpisr |= SMBUS_IT_STOPI | SMBUS_IT_NACKI;
- }
- }
-
- if((InterruptRequest & SMBUS_IT_ADDR) == SMBUS_IT_ADDR)
- {
- /* Enable ADDR, STOP interrupt */
- tmpisr |= SMBUS_IT_ADDRI | SMBUS_IT_STOPI | SMBUS_IT_NACKI;
-
- if(__HAL_SMBUS_GET_ALERT_ENABLED(hsmbus) == RESET)
- {
- /* Disable ERR interrupt */
- tmpisr |= SMBUS_IT_ERRI;
- }
- }
-
- /* Disable interrupts only at the end */
- /* to avoid a breaking situation like at "t" time */
- /* all disable interrupts request are not done */
- __HAL_SMBUS_DISABLE_IT(hsmbus, tmpisr);
-
- return HAL_OK;
-}
-/**
- * @brief This function handles SMBUS Communication Timeout.
- * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param Flag: specifies the SMBUS flag to check.
- * @param Status: The new Flag status (SET or RESET).
- * @param Timeout: Timeout duration
- * @retval HAL status
- */
-static HAL_StatusTypeDef SMBUS_WaitOnFlagUntilTimeout(SMBUS_HandleTypeDef *hsmbus, uint32_t Flag, FlagStatus Status, uint32_t Timeout)
-{
- uint32_t tickstart = HAL_GetTick();
-
- /* Wait until flag is set */
- if(Status == RESET)
- {
- while(__HAL_SMBUS_GET_FLAG(hsmbus, Flag) == RESET)
- {
- /* Check for the Timeout */
- if(Timeout != HAL_MAX_DELAY)
- {
- if((Timeout == 0) || ((HAL_GetTick()-tickstart) > Timeout))
- {
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State= HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_TIMEOUT;
- }
- }
- }
- }
- else
- {
- while(__HAL_SMBUS_GET_FLAG(hsmbus, Flag) != RESET)
- {
- /* Check for the Timeout */
- if(Timeout != HAL_MAX_DELAY)
- {
- if((Timeout == 0) || ((HAL_GetTick()-tickstart) > Timeout))
- {
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State= HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_TIMEOUT;
- }
- }
- }
- }
- return HAL_OK;
-}
-
-/**
- * @brief Handles SMBUSx communication when starting transfer or during transfer (TC or TCR flag are set).
- * @param hsmbus: SMBUS handle.
- * @param DevAddress: specifies the slave address to be programmed.
- * @param Size: specifies the number of bytes to be programmed.
- * This parameter must be a value between 0 and 255.
- * @param Mode: new state of the SMBUS START condition generation.
- * This parameter can be one or a combination of the following values:
- * @arg SMBUS_NO_MODE: No specific mode enabled.
- * @arg SMBUS_RELOAD_MODE: Enable Reload mode.
- * @arg SMBUS_AUTOEND_MODE: Enable Automatic end mode.
- * @arg SMBUS_SOFTEND_MODE: Enable Software end mode and Reload mode.
- * @param Request: new state of the SMBUS START condition generation.
- * This parameter can be one of the following values:
- * @arg SMBUS_NO_STARTSTOP: Don't Generate stop and start condition.
- * @arg SMBUS_GENERATE_STOP: Generate stop condition (Size should be set to 0).
- * @arg SMBUS_GENERATE_START_READ: Generate Restart for read request.
- * @arg SMBUS_GENERATE_START_WRITE: Generate Restart for write request.
- * @retval None
- */
-static void SMBUS_TransferConfig(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t Size, uint32_t Mode, uint32_t Request)
-{
- uint32_t tmpreg = 0;
-
- /* Check the parameters */
- assert_param(IS_SMBUS_ALL_INSTANCE(hsmbus->Instance));
- assert_param(IS_SMBUS_TRANSFER_MODE(Mode));
- assert_param(IS_SMBUS_TRANSFER_REQUEST(Request));
-
- /* Get the CR2 register value */
- tmpreg = hsmbus->Instance->CR2;
-
- /* clear tmpreg specific bits */
- tmpreg &= (uint32_t)~((uint32_t)(I2C_CR2_SADD | I2C_CR2_NBYTES | I2C_CR2_RELOAD | I2C_CR2_AUTOEND | I2C_CR2_RD_WRN | I2C_CR2_START | I2C_CR2_STOP | I2C_CR2_PECBYTE));
-
- /* update tmpreg */
- tmpreg |= (uint32_t)(((uint32_t)DevAddress & I2C_CR2_SADD) | (((uint32_t)Size << 16 ) & I2C_CR2_NBYTES) | \
- (uint32_t)Mode | (uint32_t)Request);
-
- /* update CR2 register */
- hsmbus->Instance->CR2 = tmpreg;
-}
-/**
- * @}
- */
-
-#endif /* HAL_SMBUS_MODULE_ENABLED */
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/