* `make COLOR=false` - turns off color output
* `make SILENT=true` - turns off output besides errors/warnings
* `make VERBOSE=true` - outputs all of the gcc stuff (not interesting, unless you need to debug)
+* `make EXTRAFLAGS=-E` - Preprocess the code without doing any compiling (useful if you are trying to debug #define commands)
The make command itself also has some additional options, type `make --help` for more information. The most useful is probably `-jx`, which specifies that you want to compile using more than one CPU, the `x` represents the number of CPUs that you want to use. Setting that can greatly reduce the compile times, especially if you are compiling many keyboards/keymaps. I usually set it to one less than the number of CPUs that I have, so that I have some left for doing other things while it's compiling. Note that not all operating systems and make versions supports that option.
`UNICODEMAP_ENABLE`
This allows sending unicode symbols using `X(<unicode>)` in your keymap. Codes
-up to 0xFFFFF are supported, including emojis. But you need to maintain a
-separate mapping table in your keymap file.
+up to 0xFFFFFFFF are supported, including emojis. You will need to maintain
+a separate mapping table in your keymap file.
+
+Known limitations:
+- Under Mac OS, only codes up to 0xFFFF are supported.
+- Under Linux ibus, only codes up to 0xFFFFF are supported (but anything important is still under this limit for now).
+
+Characters out of range supported by the OS will be ignored.
`BLUETOOTH_ENABLE`
This allows you output audio on the C6 pin (needs abstracting). See the [audio section](#driving-a-speaker---audio-support) for more information.
+`VARIABLE_TRACE`
+
+Use this to debug changes to variable values, see the [tracing variables](#tracing-variables) section for more information.
+
### Customizing Makefile options on a per-keymap basis
If your keymap directory has a file called `Makefile` (note the filename), any Makefile options you set in that file will take precedence over other Makefile options for your particular keyboard.
## Unicode support
-You can currently send 4 hex digits with your OS-specific modifier key (RALT for OSX with the "Unicode Hex Input" layout) - this is currently limited to supporting one OS at a time, and requires a recompile for switching. 8 digit hex codes are being worked on. The keycode function is `UC(n)`, where *n* is a 4 digit hexidecimal. Enable from the Makefile.
+There are three Unicode keymap definition method available in QMK:
+
+### UNICODE_ENABLE
+
+Supports Unicode input up to 0xFFFF. The keycode function is `UC(n)` in
+keymap file, where *n* is a 4 digit hexadecimal.
+
+### UNICODEMAP_ENABLE
+
+Supports Unicode up to 0xFFFFFFFF. You need to maintain a separate mapping
+table `const uint32_t PROGMEM unicode_map[] = {...}` in your keymap file.
+The keycode function is `X(n)` where *n* is the array index of the mapping
+table.
+
+### UCIS_ENABLE
+
+TBD
+
+Unicode input in QMK works by inputing a sequence of characters to the OS,
+sort of like macro. Unfortunately, each OS has different ideas on how Unicode is inputted.
+
+This is the current list of Unicode input method in QMK:
+
+* UC_OSX: MacOS Unicode Hex Input support. Works only up to 0xFFFF. Disabled by default. To enable: go to System Preferences -> Keyboard -> Input Sources, and enable Unicode Hex.
+* UC_LNX: Unicode input method under Linux. Works up to 0xFFFFF. Should work almost anywhere on ibus enabled distros. Without ibus, this works under GTK apps, but rarely anywhere else.
+* UC_WIN: (not recommended) Windows built-in Unicode input. To enable: create registry key under `HKEY_CURRENT_USER\Control Panel\Input Method\EnableHexNumpad` of type `REG_SZ` called `EnableHexNumpad`, set its value to 1, and reboot. This method is not recommended because of reliability and compatibility issue, use WinCompose method below instead.
+* UC_WINC: Windows Unicode input using WinCompose. Requires [WinCompose](https://github.com/samhocevar/wincompose). Works reliably under many (all?) variations of Windows.
## Backlight Breathing
RGBLIGHT_ENABLE = yes
-In order to use the underglow timer functions, you need to have `#define RGBLIGHT_TIMER` in your `config.h`, and have audio disabled (`AUDIO_ENABLE = no` in your Makefile).
+In order to use the underglow animation functions, you need to have `#define RGBLIGHT_ANIMATIONS` in your `config.h`.
Please add the following options into your config.h, and set them up according your hardware configuration. These settings are for the `F4` pin by default:
#define RGB_DI_PIN F4 // The pin your RGB strip is wired to
- #define RGBLIGHT_TIMER // Require for fancier stuff (not compatible with audio)
+ #define RGBLIGHT_ANIMATIONS // Require for fancier stuff (not compatible with audio)
#define RGBLED_NUM 14 // Number of LEDs
#define RGBLIGHT_HUE_STEP 10
#define RGBLIGHT_SAT_STEP 17
Please note the USB port can only supply a limited amount of power to the keyboard (500mA by standard, however, modern computer and most usb hubs can provide 700+mA.). According to the data of NeoPixel from Adafruit, 30 WS2812 LEDs require a 5V 1A power supply, LEDs used in this mod should not more than 20.
+## PS/2 Mouse Support
+
+Its possible to hook up a PS/2 mouse (for example touchpads or trackpoints) to your keyboard as a composite device.
+
+Then, decide whether to use USART (best), interrupts (better) or busywait (not recommended), and enable the relevant option.
+
+### Busywait version
+
+Note: This is not recommended, you may encounter jerky movement or unsent inputs. Please use interrupt or USART version if possible.
+
+In rules.mk:
+
+```
+PS2_MOUSE_ENABLE = yes
+PS2_USE_BUSYWAIT = yes
+```
+
+In your keyboard config.h:
+
+```
+#ifdef PS2_USE_BUSYWAIT
+# define PS2_CLOCK_PORT PORTD
+# define PS2_CLOCK_PIN PIND
+# define PS2_CLOCK_DDR DDRD
+# define PS2_CLOCK_BIT 1
+# define PS2_DATA_PORT PORTD
+# define PS2_DATA_PIN PIND
+# define PS2_DATA_DDR DDRD
+# define PS2_DATA_BIT 2
+#endif
+```
+
+### Interrupt version
+
+The following example uses D2 for clock and D5 for data. You can use any INT or PCINT pin for clock, and any pin for data.
+
+In rules.mk:
+
+```
+PS2_MOUSE_ENABLE = yes
+PS2_USE_INT = yes
+```
+
+In your keyboard config.h:
+
+```
+#ifdef PS2_USE_INT
+#define PS2_CLOCK_PORT PORTD
+#define PS2_CLOCK_PIN PIND
+#define PS2_CLOCK_DDR DDRD
+#define PS2_CLOCK_BIT 2
+#define PS2_DATA_PORT PORTD
+#define PS2_DATA_PIN PIND
+#define PS2_DATA_DDR DDRD
+#define PS2_DATA_BIT 5
+
+#define PS2_INT_INIT() do { \
+ EICRA |= ((1<<ISC21) | \
+ (0<<ISC20)); \
+} while (0)
+#define PS2_INT_ON() do { \
+ EIMSK |= (1<<INT2); \
+} while (0)
+#define PS2_INT_OFF() do { \
+ EIMSK &= ~(1<<INT2); \
+} while (0)
+#define PS2_INT_VECT INT2_vect
+#endif
+```
+
+### USART version
+
+To use USART on the ATMega32u4, you have to use PD5 for clock and PD2 for data. If one of those are unavailable, you need to use interrupt version.
+
+In rules.mk:
+
+```
+PS2_MOUSE_ENABLE = yes
+PS2_USE_USART = yes
+```
+
+In your keyboard config.h:
+
+```
+#ifdef PS2_USE_USART
+#define PS2_CLOCK_PORT PORTD
+#define PS2_CLOCK_PIN PIND
+#define PS2_CLOCK_DDR DDRD
+#define PS2_CLOCK_BIT 5
+#define PS2_DATA_PORT PORTD
+#define PS2_DATA_PIN PIND
+#define PS2_DATA_DDR DDRD
+#define PS2_DATA_BIT 2
+
+/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
+/* set DDR of CLOCK as input to be slave */
+#define PS2_USART_INIT() do { \
+ PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT); \
+ PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT); \
+ UCSR1C = ((1 << UMSEL10) | \
+ (3 << UPM10) | \
+ (0 << USBS1) | \
+ (3 << UCSZ10) | \
+ (0 << UCPOL1)); \
+ UCSR1A = 0; \
+ UBRR1H = 0; \
+ UBRR1L = 0; \
+} while (0)
+#define PS2_USART_RX_INT_ON() do { \
+ UCSR1B = ((1 << RXCIE1) | \
+ (1 << RXEN1)); \
+} while (0)
+#define PS2_USART_RX_POLL_ON() do { \
+ UCSR1B = (1 << RXEN1); \
+} while (0)
+#define PS2_USART_OFF() do { \
+ UCSR1C = 0; \
+ UCSR1B &= ~((1 << RXEN1) | \
+ (1 << TXEN1)); \
+} while (0)
+#define PS2_USART_RX_READY (UCSR1A & (1<<RXC1))
+#define PS2_USART_RX_DATA UDR1
+#define PS2_USART_ERROR (UCSR1A & ((1<<FE1) | (1<<DOR1) | (1<<UPE1)))
+#define PS2_USART_RX_VECT USART1_RX_vect
+#endif
+#endif
+#endif
+```
+
## Safety Considerations
You probably don't want to "brick" your keyboard, making it impossible
It's not yet possible to do a full integration test, where you would compile the whole firmware and define a keymap that you are going to test. However there are plans for doing that, because writing tests that way would probably be easier, at least for people that are not used to unit testing.
In that model you would emulate the input, and expect a certain output from the emulated keyboard.
+
+# Tracing variables
+
+Sometimes you might wonder why a variable gets changed and where, and this can be quite tricky to track down without having a debugger. It's of course possible to manually add print statements to track it, but you can also enable the variable trace feature. This works for both for variables that are changed by the code, and when the variable is changed by some memory corruption.
+
+To take the feature into use add `VARIABLE_TRACE=x` to the end of you make command. `x` represents the number of variables you want to trace, which is usually 1.
+
+Then at a suitable place in the code, call `ADD_TRACED_VARIABLE`, to begin the tracing. For example to trace all the layer changes, you can do this
+```c
+void matrix_init_user(void) {
+ ADD_TRACED_VARIABLE("layer", &layer_state, sizeof(layer_state));
+}
+```
+
+This will add a traced variable named "layer" (the name is just for your information), which tracks the memory location of `layer_state`. It tracks 4 bytes (the size of `layer_state`), so any modification to the variable will be reported. By default you can not specify a size bigger than 4, but you can change it by adding `MAX_VARIABLE_TRACE_SIZE=x` to the end of the make command line.
+
+In order to actually detect changes to the variables you should call `VERIFY_TRACED_VARIABLES` around the code that you think that modifies the variable. If a variable is modified it will tell you between which two `VERIFY_TRACED_VARIABLES` calls the modification happened. You can then add more calls to track it down further. I don't recommend spamming the codebase with calls. It's better to start with a few, and then keep adding them in a binary search fashion. You can also delete the ones you don't need, as each call need to store the file name and line number in the ROM, so you can run out of memory if you add too many calls.
+
+Also remember to delete all the tracing code ones you have found the bug, as you wouldn't want to create a pull request with tracing code.
\ No newline at end of file
projects / qmk_firmware.git / blobdiff