#ifdef HAPTIC_ENABLE
process_haptic(keycode, record) &&
#endif //HAPTIC_ENABLE
- #if defined(RGB_MATRIX_ENABLE) && defined(RGB_MATRIX_KEYREACTIVE_ENABLED)
+ #if defined(RGB_MATRIX_ENABLE)
process_rgb_matrix(keycode, record) &&
#endif
process_record_kb(keycode, record) &&
return false;
case DEBUG:
if (record->event.pressed) {
- debug_enable = true;
+ debug_enable ^= 1;
+ if (debug_enable) {
print("DEBUG: enabled.\n");
+ } else {
+ print("DEBUG: disabled.\n");
+ }
}
return false;
case EEPROM_RESET:
# define TCCRxB TCCR1B
# define COMxx1 COM1C1
# define OCRxx OCR1C
+# define TIMERx_OVF_vect TIMER1_OVF_vect
+# define TOIEx TOIE1
# define ICRx ICR1
+# define TIMSKx TIMSK1
#elif BACKLIGHT_PIN == B6
# define HARDWARE_PWM
# define TCCRxA TCCR1A
# define TCCRxB TCCR1B
# define COMxx1 COM1B1
# define OCRxx OCR1B
+# define TIMERx_OVF_vect TIMER1_OVF_vect
+# define TOIEx TOIE1
# define ICRx ICR1
+# define TIMSKx TIMSK1
#elif BACKLIGHT_PIN == B5
# define HARDWARE_PWM
# define TCCRxA TCCR1A
# define TCCRxB TCCR1B
# define COMxx1 COM1A1
# define OCRxx OCR1A
+# define TIMERx_OVF_vect TIMER1_OVF_vect
+# define TOIEx TOIE1
# define ICRx ICR1
+# define TIMSKx TIMSK1
#elif BACKLIGHT_PIN == C6
# define HARDWARE_PWM
# define TCCRxA TCCR3A
# define TCCRxB TCCR3B
-# define COMxx1 COM1A1
+# define COMxx1 COM3A1
# define OCRxx OCR3A
+# define TIMERx_OVF_vect TIMER3_OVF_vect
+# define TOIEx TOIE3
# define ICRx ICR3
+# define TIMSKx TIMSK3
#elif defined(__AVR_ATmega32A__) && BACKLIGHT_PIN == D4
# define TCCRxA TCCR1A
# define TCCRxB TCCR1B
# define COMxx1 COM1B1
# define OCRxx OCR1B
+# define TIMERx_OVF_vect TIMER1_OVF_vect
+# define TOIEx TOIE1
# define ICRx ICR1
-# define TIMSK1 TIMSK
+# define TIMSKx TIMSK1
#else
# if !defined(BACKLIGHT_CUSTOM_DRIVER)
# if !defined(B5_AUDIO) && !defined(B6_AUDIO) && !defined(B7_AUDIO)
# define TCCRxA TCCR1A
# define TCCRxB TCCR1B
# define OCRxx OCR1A
-# define OCRxAH OCR1AH
-# define OCRxAL OCR1AL
# define TIMERx_COMPA_vect TIMER1_COMPA_vect
# define TIMERx_OVF_vect TIMER1_OVF_vect
# define OCIExA OCIE1A
# define TOIEx TOIE1
# define ICRx ICR1
-# ifndef TIMSK
-# define TIMSK TIMSK1
+# if defined(__AVR_ATmega32A__) // This MCU has only one TIMSK register
+# define TIMSKx TIMSK
+# else
+# define TIMSKx TIMSK1
# endif
# elif !defined(C6_AUDIO) && !defined(C5_AUDIO) && !defined(C4_AUDIO)
#pragma message "Using hardware timer 3 with software PWM"
# define TCCRxA TCCR3A
# define TCCRxB TCCR3B
# define OCRxx OCR3A
-# define OCRxAH OCR3AH
-# define OCRxAL OCR3AL
# define TIMERx_COMPA_vect TIMER3_COMPA_vect
# define TIMERx_OVF_vect TIMER3_OVF_vect
# define OCIExA OCIE3A
# define TOIEx TOIE3
# define ICRx ICR1
-# ifndef TIMSK
-# define TIMSK TIMSK3
-# endif
+# define TIMSKx TIMSK3
# else
#pragma message "Audio in use - using pure software PWM"
#define NO_HARDWARE_PWM
if (level == 0) {
#ifdef BACKLIGHT_PWM_TIMER
if (OCRxx) {
- TIMSK &= ~(_BV(OCIExA));
- TIMSK &= ~(_BV(TOIEx));
+ TIMSKx &= ~(_BV(OCIExA));
+ TIMSKx &= ~(_BV(TOIEx));
FOR_EACH_LED(
backlight_off(backlight_pin);
)
} else {
#ifdef BACKLIGHT_PWM_TIMER
if (!OCRxx) {
- TIMSK |= _BV(OCIExA);
- TIMSK |= _BV(TOIEx);
+ TIMSKx |= _BV(OCIExA);
+ TIMSKx |= _BV(TOIEx);
}
#else
// Turn on PWM control of backlight pin
#else
bool is_breathing(void) {
- return !!(TIMSK1 & _BV(TOIE1));
+ return !!(TIMSKx & _BV(TOIEx));
}
-#define breathing_interrupt_enable() do {TIMSK1 |= _BV(TOIE1);} while (0)
-#define breathing_interrupt_disable() do {TIMSK1 &= ~_BV(TOIE1);} while (0)
+#define breathing_interrupt_enable() do {TIMSKx |= _BV(TOIEx);} while (0)
+#define breathing_interrupt_disable() do {TIMSKx &= ~_BV(TOIEx);} while (0)
#endif
#define breathing_min() do {breathing_counter = 0;} while (0)
/* Assuming a 16MHz CPU clock and a timer that resets at 64k (ICR1), the following interrupt handler will run
* about 244 times per second.
*/
-ISR(TIMER1_OVF_vect)
+ISR(TIMERx_OVF_vect)
#endif
{
uint16_t interval = (uint16_t) breathing_period * 244 / BREATHING_STEPS;