Add RGB support for Let’s Split v1

[qmk_firmware.git] / quantum / config_common.h

diff --git a/quantum/config_common.h b/quantum/config_common.h
index da53fce89b5b8ddaeabb40469433b20bf21dd32f..28f68b9c7001739770068c7348fc67fe4b1a5bcf 100644 (file)
--- a/quantum/config_common.h
+++ b/quantum/config_common.h
@@ -1,116 +1,87 @@
 #ifndef CONFIG_DEFINITIONS_H
 #define CONFIG_DEFINITIONS_H
 
-#define B0 0x20
-#define B1 0x21
-#define B2 0x22
-#define B3 0x23
-#define B4 0x24
-#define B5 0x25
-#define B6 0x26
-#define B7 0x27
-#define C0 0x30
-#define C1 0x31
-#define C2 0x32
-#define C3 0x33
-#define C4 0x34
-#define C5 0x35
-#define C6 0x36
-#define C7 0x37
-#define D0 0x40
-#define D1 0x41
-#define D2 0x42
-#define D3 0x43
-#define D4 0x44
-#define D5 0x45
-#define D6 0x46
-#define D7 0x47
-#define E0 0x50
-#define E1 0x51
-#define E2 0x52
-#define E3 0x53
-#define E4 0x54
-#define E5 0x55
-#define E6 0x56
-#define E7 0x57
-#define F0 0x60
-#define F1 0x61
-#define F2 0x62
-#define F3 0x63
-#define F4 0x64
-#define F5 0x65
-#define F6 0x66
-#define F7 0x67
+/* diode directions */
+#define COL2ROW       0
+#define ROW2COL       1
+#define CUSTOM_MATRIX 2 /* Disables built-in matrix scanning code */
 
-#define COL2ROW 0x0
-#define ROW2COL 0x1
-
-#ifdef BLUETOOTH_ENABLE
-#ifdef __AVR_ATmega32U4__
-    #define SERIAL_UART_BAUD       9600
-    #define SERIAL_UART_DATA       UDR1
-    #define SERIAL_UART_UBRR       ((F_CPU/(16UL*SERIAL_UART_BAUD))-1)
-    #define SERIAL_UART_RXD_VECT   USART1_RX_vect
-    #define SERIAL_UART_TXD_READY  (UCSR1A&(1<<UDRE1))
-    #define SERIAL_UART_INIT()     do { \
-        UBRR1L = (uint8_t) SERIAL_UART_UBRR;       /* baud rate */ \
-        UBRR1H = (uint8_t) (SERIAL_UART_UBRR>>8);  /* baud rate */ \
-        UCSR1B = (1<<TXEN1);                /* TX: enable */ \
-        UCSR1C = (0<<UPM11) | (0<<UPM10) | /* parity: none(00), even(01), odd(11) */ \
-                 (0<<UCSZ12) | (1<<UCSZ11) | (1<<UCSZ10); /* data-8bit(011) */ \
-               sei(); \
-    } while(0)
-#else
-#   error "USART configuration is needed."
-#endif
-
-
-// I'm fairly sure these aren't needed, but oh well - Jack
-
-/*
- * PS/2 Interrupt configuration
- */
-#ifdef PS2_USE_INT
-/* uses INT1 for clock line(ATMega32U4) */
-#define PS2_CLOCK_PORT  PORTD
-#define PS2_CLOCK_PIN   PIND
-#define PS2_CLOCK_DDR   DDRD
-#define PS2_CLOCK_BIT   1
-
-#define PS2_DATA_PORT   PORTD
-#define PS2_DATA_PIN    PIND
-#define PS2_DATA_DDR    DDRD
-#define PS2_DATA_BIT    0
-
-#define PS2_INT_INIT()  do {    \
-    EICRA |= ((1<<ISC11) |      \
-              (0<<ISC10));      \
-} while (0)
-#define PS2_INT_ON()  do {      \
-    EIMSK |= (1<<INT1);         \
-} while (0)
-#define PS2_INT_OFF() do {      \
-    EIMSK &= ~(1<<INT1);        \
-} while (0)
-#define PS2_INT_VECT    INT1_vect
+/* I/O pins */
+#ifndef F0
+    #define B0 0x30
+    #define B1 0x31
+    #define B2 0x32
+    #define B3 0x33
+    #define B4 0x34
+    #define B5 0x35
+    #define B6 0x36
+    #define B7 0x37
+    #define C0 0x60
+    #define C1 0x61
+    #define C2 0x62
+    #define C3 0x63
+    #define C4 0x64
+    #define C5 0x65
+    #define C6 0x66
+    #define C7 0x67
+    #define D0 0x90
+    #define D1 0x91
+    #define D2 0x92
+    #define D3 0x93
+    #define D4 0x94
+    #define D5 0x95
+    #define D6 0x96
+    #define D7 0x97
+    #define E0 0xC0
+    #define E1 0xC1
+    #define E2 0xC2
+    #define E3 0xC3
+    #define E4 0xC4
+    #define E5 0xC5
+    #define E6 0xC6
+    #define E7 0xC7
+    #define F0 0xF0
+    #define F1 0xF1
+    #define F2 0xF2
+    #define F3 0xF3
+    #define F4 0xF4
+    #define F5 0xF5
+    #define F6 0xF6
+    #define F7 0xF7
+    #define A0 0x00
+    #define A1 0x01
+    #define A2 0x02
+    #define A3 0x03
+    #define A4 0x04
+    #define A5 0x05
+    #define A6 0x06
+    #define A7 0x07
 #endif
 
-/*
- * PS/2 Busywait configuration
- */
-#ifdef PS2_USE_BUSYWAIT
-#define PS2_CLOCK_PORT  PORTD
-#define PS2_CLOCK_PIN   PIND
-#define PS2_CLOCK_DDR   DDRD
-#define PS2_CLOCK_BIT   1
-
-#define PS2_DATA_PORT   PORTD
-#define PS2_DATA_PIN    PIND
-#define PS2_DATA_DDR    DDRD
-#define PS2_DATA_BIT    0
+/* USART configuration */
+#ifdef BLUETOOTH_ENABLE
+#   ifdef __AVR_ATmega32U4__
+#      define SERIAL_UART_BAUD 9600
+#      define SERIAL_UART_DATA UDR1
+#      define SERIAL_UART_UBRR (F_CPU / (16UL * SERIAL_UART_BAUD) - 1)
+#      define SERIAL_UART_RXD_VECT USART1_RX_vect
+#      define SERIAL_UART_TXD_READY (UCSR1A & _BV(UDRE1))
+#      define SERIAL_UART_INIT() do { \
+            /* baud rate */ \
+            UBRR1L = SERIAL_UART_UBRR; \
+            /* baud rate */ \
+            UBRR1H = SERIAL_UART_UBRR >> 8; \
+            /* enable TX */ \
+            UCSR1B = _BV(TXEN1); \
+            /* 8-bit data */ \
+            UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); \
+            sei(); \
+        } while(0)
+#   else
+#       error "USART configuration is needed."
+#   endif
 #endif
 
-#endif
+#define API_SYSEX_MAX_SIZE 32
 
 #endif
-