Keyboard: Add QWERTYYdox keyboard (#3636)

[qmk_firmware.git] / keyboards / qwertyydox / rules.mk

diff --git a/keyboards/qwertyydox/rules.mk b/keyboards/qwertyydox/rules.mk
new file mode 100644 (file)
index 0000000..d8a287b
--- /dev/null
+++ b/keyboards/qwertyydox/rules.mk
@@ -0,0 +1,69 @@
+# MCU name\r
+#MCU = at90usb1287\r
+MCU = atmega32u4\r
+\r
+# Processor frequency.\r
+#     This will define a symbol, F_CPU, in all source code files equal to the\r
+#     processor frequency in Hz. You can then use this symbol in your source code to\r
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done\r
+#     automatically to create a 32-bit value in your source code.\r
+#\r
+#     This will be an integer division of F_USB below, as it is sourced by\r
+#     F_USB after it has run through any CPU prescalers. Note that this value\r
+#     does not *change* the processor frequency - it should merely be updated to\r
+#     reflect the processor speed set externally so that the code can use accurate\r
+#     software delays.\r
+F_CPU = 16000000\r
+\r
+#\r
+# LUFA specific\r
+#\r
+# Target architecture (see library "Board Types" documentation).\r
+ARCH = AVR8\r
+\r
+# Input clock frequency.\r
+#     This will define a symbol, F_USB, in all source code files equal to the\r
+#     input clock frequency (before any prescaling is performed) in Hz. This value may\r
+#     differ from F_CPU if prescaling is used on the latter, and is required as the\r
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed\r
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'\r
+#     at the end, this will be done automatically to create a 32-bit value in your\r
+#     source code.\r
+#\r
+#     If no clock division is performed on the input clock inside the AVR (via the\r
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.\r
+F_USB = $(F_CPU)\r
+\r
+# Bootloader\r
+#     This definition is optional, and if your keyboard supports multiple bootloaders of\r
+#     different sizes, comment this out, and the correct address will be loaded \r
+#     automatically (+60). See bootloader.mk for all options.\r
+BOOTLOADER = caterina\r
+\r
+# Interrupt driven control endpoint task(+60)\r
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT\r
+\r
+# Build Options\r
+#   change to "no" to disable the options, or define them in the Makefile in\r
+#   the appropriate keymap folder that will get included automatically\r
+#\r
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)\r
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)\r
+EXTRAKEY_ENABLE = no       # Audio control and System control(+450)\r
+CONSOLE_ENABLE = no         # Console for debug(+400)\r
+COMMAND_ENABLE = no        # Commands for debug and configuration\r
+NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work\r
+BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality\r
+MIDI_ENABLE = no            # MIDI controls\r
+AUDIO_ENABLE = no           # Audio output on port C6\r
+UNICODE_ENABLE = no         # Unicode\r
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID\r
+RGBLIGHT_ENABLE = no       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.\r
+SUBPROJECT_rev1 = yes\r
+USE_I2C = yes               # I2C is used between the sides\r
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE\r
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend\r
+\r
+SPLIT_KEYBOARD = yes\r
+\r
+DEFAULT_FOLDER = qwertyydox/rev1\r