#include "preonic.h"
+#ifdef ONEHAND_ENABLE
__attribute__ ((weak))
-void matrix_init_user(void) {
-
-};
-
-__attribute__ ((weak))
-void matrix_scan_user(void) {
-
-};
-
-__attribute__ ((weak))
-bool process_action_user(keyrecord_t *record) {
- return true;
+const keypos_t hand_swap_config[MATRIX_ROWS][MATRIX_COLS] = {
+ {{11, 0}, {10, 0}, {9, 0}, {8, 0}, {7, 0}, {6, 0}, {5, 0}, {4, 0}, {3, 0}, {2, 0}, {1, 0}, {0, 0}},
+ {{11, 1}, {10, 1}, {9, 1}, {8, 1}, {7, 1}, {6, 1}, {5, 1}, {4, 1}, {3, 1}, {2, 1}, {1, 1}, {0, 1}},
+ {{11, 2}, {10, 2}, {9, 2}, {8, 2}, {7, 2}, {6, 2}, {5, 2}, {4, 2}, {3, 2}, {2, 2}, {1, 2}, {0, 2}},
+ {{11, 3}, {10, 3}, {9, 3}, {8, 3}, {7, 3}, {6, 3}, {5, 3}, {4, 3}, {3, 3}, {2, 3}, {1, 3}, {0, 3}},
+ {{11, 4}, {10, 4}, {9, 4}, {8, 4}, {7, 4}, {6, 4}, {5, 4}, {4, 4}, {3, 4}, {2, 4}, {1, 4}, {0, 4}},
};
+#endif
void matrix_init_kb(void) {
- #ifdef BACKLIGHT_ENABLE
- backlight_init_ports();
- #endif
// Turn status LED on
DDRE |= (1<<6);
PORTE |= (1<<6);
matrix_init_user();
-};
-
-void matrix_scan_kb(void) {
- matrix_scan_user();
-};
-
-bool process_action_kb(keyrecord_t *record) {
- return process_action_user(record);
-}
-
-#ifdef BACKLIGHT_ENABLE
-#define CHANNEL OCR1C
-
-void backlight_init_ports()
-{
-
- // Setup PB7 as output and output low.
- DDRB |= (1<<7);
- PORTB &= ~(1<<7);
-
- // Use full 16-bit resolution.
- ICR1 = 0xFFFF;
-
- // I could write a wall of text here to explain... but TL;DW
- // Go read the ATmega32u4 datasheet.
- // And this: http://blog.saikoled.com/post/43165849837/secret-konami-cheat-code-to-high-resolution-pwm-on
-
- // Pin PB7 = OCR1C (Timer 1, Channel C)
- // Compare Output Mode = Clear on compare match, Channel C = COM1C1=1 COM1C0=0
- // (i.e. start high, go low when counter matches.)
- // WGM Mode 14 (Fast PWM) = WGM13=1 WGM12=1 WGM11=1 WGM10=0
- // Clock Select = clk/1 (no prescaling) = CS12=0 CS11=0 CS10=1
-
- TCCR1A = _BV(COM1C1) | _BV(WGM11); // = 0b00001010;
- TCCR1B = _BV(WGM13) | _BV(WGM12) | _BV(CS10); // = 0b00011001;
-
- backlight_init();
-}
-
-void backlight_set(uint8_t level)
-{
- if ( level == 0 )
- {
- // Turn off PWM control on PB7, revert to output low.
- TCCR1A &= ~(_BV(COM1C1));
- CHANNEL = 0x0;
- // Prevent backlight blink on lowest level
- PORTB &= ~(_BV(PORTB7));
- }
- else if ( level == BACKLIGHT_LEVELS )
- {
- // Prevent backlight blink on lowest level
- PORTB &= ~(_BV(PORTB7));
- // Turn on PWM control of PB7
- TCCR1A |= _BV(COM1C1);
- // Set the brightness
- CHANNEL = 0xFFFF;
- }
- else
- {
- // Prevent backlight blink on lowest level
- PORTB &= ~(_BV(PORTB7));
- // Turn on PWM control of PB7
- TCCR1A |= _BV(COM1C1);
- // Set the brightness
- CHANNEL = 0xFFFF >> ((BACKLIGHT_LEVELS - level) * ((BACKLIGHT_LEVELS + 1) / 2));
- }
-}
-
-#endif
+};
\ No newline at end of file