#MCU = at90usb1286
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
#
# LUFA specific
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
+# Bootloader
+# This definition is optional, and if your keyboard supports multiple bootloaders of
+# different sizes, comment this out, and the correct address will be loaded
+# automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = caterina
+
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# change yes to no to disable
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = yes # Console for debug(+400)
-COMMAND_ENABLE = yes # Commands for debug and configuration
+CONSOLE_ENABLE = no # Console for debug(+400)
+COMMAND_ENABLE = no # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE = no # USB Nkey Rollover
-BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
-RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
+RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
-
-ISSI_ENABLE = no # If the I2C pullup resistors aren't install this must be disabled
-#WATCHDOG_ENABLE = yes # Resets keyboard if matrix_scan isn't run every 250ms
+BACKLIGHT_CUSTOM_DRIVER = yes
+BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality, also set ISSI_ENABLE below for Miera
+ISSI_ENABLE = yes # If the I2C pullup resistors aren't install this must be disabled
CUSTOM_MATRIX = yes
-ifeq ($(strip $(ISSI_ENABLE)), yes)
- TMK_COMMON_DEFS += -DISSI_ENABLE
-endif
-
-ifeq ($(strip $(WATCHDOG_ENABLE)), yes)
- TMK_COMMON_DEFS += -DWATCHDOG_ENABLE
-endif
+#ifeq ($(strip $(ISSI_ENABLE)), yes)
+# TMK_COMMON_DEFS += -DISSI_ENABLE
+#endif
+#
+#ifeq ($(strip $(WATCHDOG_ENABLE)), yes)
+# TMK_COMMON_DEFS += -DWATCHDOG_ENABLE
+#endif
DEFAULT_FOLDER = meira/promicro
LAYOUTS = ortho_4x12