]> git.donarmstrong.com Git - qmk_firmware.git/blobdiff - keyboards/maxipad/rules.mk
[Keyboard] Initial refactor of maxipad to conform to current standards (#5233)
[qmk_firmware.git] / keyboards / maxipad / rules.mk
index 56b2042efa087c5d07a738f56eaae4f041d29595..735c7af26d694d6de313b45217e36e2ef755480b 100644 (file)
@@ -1,67 +1,22 @@
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
-
 # Build Options
 #   change yes to no to disable
 #
-BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes        # Console for debug(+400)
-COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = no         # Commands for debug and configuration
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
 # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE ?= no            # USB Nkey Rollover
-BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE ?= no            # MIDI controls
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE ?= no           # Audio output on port C6
\ No newline at end of file
+NKRO_ENABLE = yes           # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no            # Enable support for HD44780 based LCDs (+400)
+
+DEFAULT_FOLDER = maxipad/promicro