-\r
-\r
-# MCU name\r
-#MCU = at90usb1287\r
-MCU = atmega32u4\r
-\r
-# Processor frequency.\r
-# This will define a symbol, F_CPU, in all source code files equal to the\r
-# processor frequency in Hz. You can then use this symbol in your source code to\r
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done\r
-# automatically to create a 32-bit value in your source code.\r
-#\r
-# This will be an integer division of F_USB below, as it is sourced by\r
-# F_USB after it has run through any CPU prescalers. Note that this value\r
-# does not *change* the processor frequency - it should merely be updated to\r
-# reflect the processor speed set externally so that the code can use accurate\r
-# software delays.\r
-F_CPU = 16000000\r
-\r
-\r
-#\r
-# LUFA specific\r
-#\r
-# Target architecture (see library "Board Types" documentation).\r
-ARCH = AVR8\r
-\r
-# Input clock frequency.\r
-# This will define a symbol, F_USB, in all source code files equal to the\r
-# input clock frequency (before any prescaling is performed) in Hz. This value may\r
-# differ from F_CPU if prescaling is used on the latter, and is required as the\r
-# raw input clock is fed directly to the PLL sections of the AVR for high speed\r
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'\r
-# at the end, this will be done automatically to create a 32-bit value in your\r
-# source code.\r
-#\r
-# If no clock division is performed on the input clock inside the AVR (via the\r
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.\r
-F_USB = $(F_CPU)\r
-\r
-# Interrupt driven control endpoint task(+60)\r
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT\r
-\r
-\r
-# Boot Section Size in *bytes*\r
-# Teensy halfKay 512\r
-# Teensy++ halfKay 1024\r
-# Atmel DFU loader 4096\r
-# LUFA bootloader 4096\r
-# USBaspLoader 2048\r
-OPT_DEFS += -DBOOTLOADER_SIZE=4096\r
-\r
-\r
-# Build Options\r
-# comment out to disable the options.\r
-#\r
-BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)\r
-MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)\r
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)\r
-# CONSOLE_ENABLE ?= yes # Console for debug(+400)\r
-# COMMAND_ENABLE ?= yes # Commands for debug and configuration\r
-KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key\r
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE\r
-# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend\r
-NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work\r
-# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality\r
-# MIDI_ENABLE ?= YES # MIDI controls\r
-# UNICODE_ENABLE ?= YES # Unicode\r
-# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID\r
-\r
-\r
-ifndef QUANTUM_DIR\r
- include ../../Makefile\r
-endif\r
-\r
+ifndef MAKEFILE_INCLUDED
+ include ../../Makefile
+endif