[Keyboard] E6V2 BMC OE (#5908)

[qmk_firmware.git] / keyboards / exclusive / e6v2 / bmc / rules.mk

diff --git a/keyboards/exclusive/e6v2/bmc/rules.mk b/keyboards/exclusive/e6v2/bmc/rules.mk
deleted file mode 100644 (file)
index 885bce2..0000000
--- a/keyboards/exclusive/e6v2/bmc/rules.mk
+++ /dev/null
@@ -1,90 +0,0 @@
-# MCU name
-#MCU = at90usb1286
-MCU = atmega32a
-PROTOCOL = VUSB
-
-NO_UART = yes
-NO_SUSPEND_POWER_DOWN = yes
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 12000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-# ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-# F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS = -DDEBUG_LEVEL=0
-
-
-# Bootloader selection
-#   Teensy       halfkay
-#   Pro Micro    caterina
-#   Atmel DFU    atmel-dfu
-#   LUFA DFU     lufa-dfu
-#   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
-BOOTLOADER = bootloadHID
-
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = yes        # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = no            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-RGBLIGHT_CUSTOM_DRIVER = yes
-RGBLIGHT_ENABLE = yes        # Enable keyboard RGB underglow
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-HD44780_ENABLE = no            # Enable support for HD44780 based LCDs (+400)
-
-SRC += i2c_master.c
-
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex