--- /dev/null
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make = Make software.
+#
+# make clean = Clean out built project files.
+#
+# That's pretty much all you need. To compile, always go make clean,
+# followed by make.
+#
+# For advanced users only:
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+# (must have teensy_loader_cli installed).
+#
+#----------------------------------------------------------------------------
+
+# # project specific files
+SRC = \
+ twimaster.c \
+ matrix.c \
+ expander.c \
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+# Build Options
+# comment out to disable the options.
+#
+CUSTOM_MATRIX = yes # Custom matrix file for the ErgoDone
+UNICODE_ENABLE = yes # Unicode
+BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = no # Console for debug(+400)
+COMMAND_ENABLE = no # Commands for debug and configuration
+SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
+USB_6KRO_ENABLE = no # USB 6key Rollover
+BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
+KEYMAP_IN_EEPROM_ENABLE = no # External keymap in eeprom
+KEYMAP_SECTION_ENABLE = no # Fixed address keymap for keymap editor
+SOFTPWM_LED_ENABLE = no # Enable SoftPWM to drive backlight
+FADING_LED_ENABLE = no # Enable fading backlight
+BREATHING_LED_ENABLE = no # Enable breathing backlight
+LEDMAP_ENABLE = no # Enable LED mapping
+LEDMAP_IN_EEPROM_ENABLE = no # Read LED mapping from eeprom
+ONEHAND_ENABLE = no # Disable Onehand
+RGBLIGHT_ENABLE = no
+MIDI_ENABLE = no
+
+LAYOUTS = ergodox ergodox_80
\ No newline at end of file
projects / qmk_firmware.git / blobdiff