[Keyboard] fixed pins for numpad_5x4 layout (#6311)

[qmk_firmware.git] / keyboards / ergodash / rules.mk

diff --git a/keyboards/ergodash/rules.mk b/keyboards/ergodash/rules.mk
index fc06d60e288662959e72a4bf27685550897505cc..8be059d969ff2b874c67367047bd2c9e4cc8b6a6 100644 (file)
--- a/keyboards/ergodash/rules.mk
+++ b/keyboards/ergodash/rules.mk
@@ -1,52 +1,21 @@
-SRC += matrix.c \
-          i2c.c \
-          split_util.c \
-          serial.c \
-          ssd1306.c
-
 # MCU name
-#MCU = at90usb1287
 MCU = atmega32u4
 
 # Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
 F_CPU = 16000000
 
-#
 # LUFA specific
 #
 # Target architecture (see library "Board Types" documentation).
 ARCH = AVR8
 
 # Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
 
 # Interrupt driven control endpoint task(+60)
 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 
 # Bootloader
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = caterina
 
 # Build Options
@@ -57,19 +26,17 @@ BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
 MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
 EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
 CONSOLE_ENABLE = no         # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
+COMMAND_ENABLE = no        # Commands for debug and configuration
 NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
 BACKLIGHT_ENABLE = no      # Enable keyboard backlight functionality
 MIDI_ENABLE = no            # MIDI controls
 AUDIO_ENABLE = no           # Audio output on port C6
 UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = yes       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-SUBPROJECT_rev1 = yes
-USE_I2C = yes
+RGBLIGHT_ENABLE = no       # Enable WS2812 RGB underlight.
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
 SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
 
-CUSTOM_MATRIX = yes
+SPLIT_KEYBOARD = yes       # Enables split keyboard support
 
-DEFAULT_FOLDER = ergodash/rev2
+DEFAULT_FOLDER = ergodash/rev1