-
-
-ifdef TEENSY2
- OPT_DEFS += -DATREUS_TEENSY2
- ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
-else
- OPT_DEFS += -DATREUS_ASTAR
- OPT_DEFS += -DCATERINA_BOOTLOADER
- ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
- avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
-endif
-
# MCU name
-#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# software delays.
F_CPU = 16000000
-
#
# LUFA specific
#
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# atmega32a bootloadHID
+ifdef TEENSY2
+ BOOTLOADER = halfkay
+ OPT_DEFS += -DATREUS_TEENSY2
+else
+ BOOTLOADER = caterina
+ OPT_DEFS += -DATREUS_ASTAR
+ ifdef PCBDOWN
+ OPT_DEFS += -DPCBDOWN
+ endif
+endif
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
-# comment out to disable the options.
+# change yes to no to disable
#
-#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = yes # Console for debug(+400)
-COMMAND_ENABLE = yes # Commands for debug and configuration
+BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = yes # Console for debug(+400)
+COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
-NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
-# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
-# MIDI_ENABLE = YES # MIDI controls
-UNICODE_ENABLE = YES # Unicode
-# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
-
-USB = /dev/cu.usbmodem1411
-
-upload: build
- $(ATREUS_UPLOAD_COMMAND)
+SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = yes # USB Nkey Rollover
+BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow
+MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = yes # Unicode
+BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no # Audio output on port C6
+FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)