adds backlight levels to the satan keyboard (#431)

[qmk_firmware.git] / keyboard / hhkb / Makefile

diff --git a/keyboard/hhkb/Makefile b/keyboard/hhkb/Makefile
index 5cf02d194ec05c9a87d2324f3818dfce5491feef..53eece396905ae55247fedfac18da2aad6344c99 100644 (file)
--- a/keyboard/hhkb/Makefile
+++ b/keyboard/hhkb/Makefile
@@ -1,65 +1,10 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device.
-#                Please customize your programmer settings(PROGRAM_CMD)
-#
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-# make dfu = Download the hex file to the device, using dfu-programmer (must
-#            have dfu-programmer installed).
-#
-# make flip = Download the hex file to the device, using Atmel FLIP (must
-#             have Atmel FLIP installed).
-#
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
-#               (must have dfu-programmer installed).
-#
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
-#                (must have Atmel FLIP installed).
-#
-# make debug = Start either simulavr or avarice as specified for debugging, 
-#              with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-#                   bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
-# Target file name (without extension).
-TARGET = hhkb_lufa
-
-# Directory common source filess exist
-TOP_DIR = ../..
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
 
 
-# List C source files here. (C dependencies are automatically generated.)
-SRC += keymap_common.c \
-       matrix.c \
-       led.c
-
-CONFIG_H = config.h
-
+# project specific files
+SRC = matrix.c
 
 # MCU name
-# PJRC Teensy++ 2.0
-#MCU = at90usb1286
-# TMK Alt Controller or PJRC Teensy 2.0
+#MCU = at90usb1287
 MCU = atmega32u4
 
 # Processor frequency.
@@ -95,58 +40,43 @@ ARCH = AVR8
 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
 
-# Interrupt driven control endpoint task
-#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 
 
 # Boot Section Size in *bytes*
 #   Teensy halfKay   512
 #   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096      (TMK Alt Controller)
+#   Atmel DFU loader 4096
 #   LUFA bootloader  4096
 #   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+#OPT_DEFS += -DBOOTLOADER_SIZE=4096
 
+# as per original hasu settings
+OPT_DEFS += -DBOOTLOADER_SIZE=512
 
 # Build Options
 #   comment out to disable the options.
 #
-BOOTMAGIC_ENABLE = yes         # Virtual DIP switch configuration
-MOUSEKEY_ENABLE = yes          # Mouse keys
-EXTRAKEY_ENABLE = yes          # Audio control and System control
-CONSOLE_ENABLE = yes           # Console for debug
-COMMAND_ENABLE = yes           # Commands for debug and configuration
-NKRO_ENABLE = yes              # USB Nkey Rollover
-#KEYMAP_SECTION_ENABLE = yes   # fixed address keymap for keymap editor
-#HHKB_JP = yes                 # HHKB JP support
-
-
-ifdef HHKB_JP
-    OPT_DEFS += -DHHKB_JP
-endif
+BOOTMAGIC_ENABLE ?= yes        # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes  # Console for debug(+400)
+COMMAND_ENABLE ?= yes    # Commands for debug and configuration
+CUSTOM_MATRIX    ?= yes # Custom matrix file for the HHKB
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+# SLEEP_LED_ENABLE ?= yes  # Breathing sleep LED during USB suspend
+# NKRO_ENABLE ?= yes           # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+# BACKLIGHT_ENABLE ?= yes  # Enable keyboard backlight functionality
+# MIDI_ENABLE ?= YES           # MIDI controls
+# UNICODE_ENABLE ?= YES                # Unicode
+# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
 
 
-#
-# Keymap file
-#
-ifdef KEYMAP
-    SRC := keymap_$(KEYMAP).c $(SRC)
-else
-    ifdef HHKB_JP
-       SRC := keymap_jp.c $(SRC)
-    else 
-       SRC := keymap_hhkb.c $(SRC)
-    endif
-endif
 
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
-
-include $(TOP_DIR)/protocol/lufa.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
+ifndef QUANTUM_DIR
+       include ../../Makefile
+endif
 
 debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
 debug-on: all