rgblight.[ch] more configurable (#3582)

[qmk_firmware.git] / drivers / arm / i2c_master.c

diff --git a/drivers/arm/i2c_master.c b/drivers/arm/i2c_master.c
index 2fdd9f65e1cacf5f5f8affe2ba37314b9ea016f4..2a7badd351f29a8834410a0dd3385d260f297d68 100644 (file)
--- a/drivers/arm/i2c_master.c
+++ b/drivers/arm/i2c_master.c
@@ -15,12 +15,14 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
-/* This library follows the convention of the AVR i2c_master library.
+/* This library is only valid for STM32 processors.
+ * This library follows the convention of the AVR i2c_master library.
  * As a result addresses are expected to be already shifted (addr << 1).
  * I2CD1 is the default driver which corresponds to pins B6 and B7. This
  * can be changed.
  * Please ensure that HAL_USE_I2C is TRUE in the halconf.h file and that
- * STM32_I2C_USE_I2C1 is TRUE in the mcuconf.h file.
+ * STM32_I2C_USE_I2C1 is TRUE in the mcuconf.h file. Pins B6 and B7 are used
+ * but using any other I2C pins should be trivial.
  */
 
 #include "i2c_master.h"
@@ -41,7 +43,7 @@ static const I2CConfig i2cconfig = {
 
 void i2c_init(void)
 {
-  palSetGroupMode(GPIOB,6,7, PAL_MODE_INPUT);       // Try releasing special pins for a short time
+  palSetGroupMode(GPIOB, GPIOB_PIN6 | GPIOB_PIN7, 0, PAL_MODE_INPUT); // Try releasing special pins for a short time
   chThdSleepMilliseconds(10);
 
   palSetPadMode(GPIOB, 6, PAL_MODE_ALTERNATE(4) | PAL_STM32_OTYPE_OPENDRAIN | PAL_STM32_PUPDR_PULLUP);
@@ -82,12 +84,12 @@ uint8_t i2c_writeReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t l
   {
     complete_packet[i+1] = data[i];
   }
-  complete_packet[0] = regaddr
+  complete_packet[0] = regaddr;
 
   return i2cMasterTransmitTimeout(&I2C_DRIVER, (i2c_address >> 1), complete_packet, length + 1, 0, 0, MS2ST(timeout));
 }
 
-uint8_t i2c_readReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout)
+uint8_t i2c_readReg(uint8_t devaddr, uint8_t* regaddr, uint8_t* data, uint16_t length, uint16_t timeout)
 {
   i2c_address = devaddr;
   i2cStart(&I2C_DRIVER, &i2cconfig);
@@ -97,7 +99,6 @@ uint8_t i2c_readReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t le
 // This is usually not needed. It releases the driver to allow pins to become GPIO again.
 uint8_t i2c_stop(uint16_t timeout)
 {
-  i2c_address = address;
   i2cStop(&I2C_DRIVER);
   return 0;
 }