To generate a production-ready .hex file (containing the application and the bootloader), use the `production` target, eg `make planck/rev4:default:production`.
+### DFU commands
+
+There are a number of DFU commands that you can use to flash firmware to a DFU device:
+
+* `:dfu` - This is the normal option and waits until a DFU device is available, and then flashes the firmware. This will check every 5 seconds, to see if a DFU device has appeared.
+* `:dfu-ee` - This flashes an `eep` file instead of the normal hex. This is uncommon.
+* `:dfu-split-left` - This flashes the normal firmware, just like the default option (`:dfu`). However, this also flashes the "Left Side" EEPROM file for split keyboards. _This is ideal for Elite C based split keyboards._
+* `:dfu-split-right` - This flashes the normal firmware, just like the default option (`:dfu`). However, this also flashes the "Right Side" EEPROM file for split keyboards. _This is ideal for Elite C based split keyboards._
+
## Caterina
-Arduino boards and their clones use the [Caterina bootloader](https://github.com/arduino/Arduino/tree/master/hardware/arduino/avr/bootloaders/caterina) (any keyboard built with a Pro Micro, or clone), and uses the avr109 protocol to communicate through virtual serial. Bootloaders like [A-Star](https://www.pololu.com/docs/0J61/9) are based on Caterina.
+Arduino boards and their clones use the [Caterina bootloader](https://github.com/arduino/ArduinoCore-avr/tree/master/bootloaders/caterina) (any keyboard built with a Pro Micro, or clone), and uses the avr109 protocol to communicate through virtual serial. Bootloaders like [A-Star](https://www.pololu.com/docs/0J61/9) are based on Caterina.
To ensure compatibility with the Caterina bootloader, make sure this block is present your `rules.mk`:
When you're done flashing boards, you'll need to hit Ctrl + C or whatever the correct keystroke is for your operating system to break the loop.
+
## Halfkay
Halfkay is a super-slim protocol developed by PJRC that uses HID, and come on all Teensys (namely the 2.0).
3. Flash a .hex file
4. Reset the device into application mode (may be done automatically)
+## USBasploader
+
+USBasploader is a bootloader developed by matrixstorm. It is used in some non-USB AVR chips such as the ATmega328P, which run V-USB.
+
+To ensure compatibility with the USBasploader bootloader, make sure this block is present in your `rules.mk`:
+
+ # Bootloader
+ # This definition is optional, and if your keyboard supports multiple bootloaders of
+ # different sizes, comment this out, and the correct address will be loaded
+ # automatically (+60). See bootloader.mk for all options.
+ BOOTLOADER = USBasp
+
+Compatible flashers:
+
+* [QMK Toolbox](https://github.com/qmk/qmk_toolbox/releases) (recommended GUI)
+* [avrdude](http://www.nongnu.org/avrdude/) with the `usbasp` programmer
+* [AVRDUDESS](https://github.com/zkemble/AVRDUDESS)
+
+Flashing sequence:
+
+1. Press the `RESET` keycode, or keep the boot pin shorted to GND while quickly shorting RST to GND
+2. Wait for the OS to detect the device
+3. Flash a .hex file
+4. Reset the device into application mode (may be done automatically)
+
## STM32
All STM32 chips come preloaded with a factory bootloader that cannot be modified nor deleted. Some STM32 chips have bootloaders that do not come with USB programming (e.g. STM32F103) but the process is still the same.
* You will receive a warning about the DFU signature; Just ignore it
4. Reset the device into application mode (may be done automatically)
* If you are building from command line (e.g. `make planck/rev6:default:dfu-util`), make sure that `:leave` is passed to the `DFU_ARGS` variable inside your `rules.mk` (e.g. `DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave`) so that your device resets after flashing
+
+### STM32 Commands
+
+There are a number of DFU commands that you can use to flash firmware to a STM32 device:
+
+* `:dfu-util` - The default command for flashing to STM32 devices.
+* `:dfu-util-wait` - This works like the default command, but it gives you a (configurable) 10 second timeout before it attempts to flash the firmware. You can use `TIME_DELAY=20` from the command line to change the timeout.
+ * Eg: `make <keyboard>:<keymap>:dfu-util TIME_DELAY=5`
+* `:st-link-cli` - This allows you to flash the firmware via ST-LINK's CLI utility, rather than dfu-util.