#### 2.3.2 Examples
***TODO: sample implementation***
-See `keyboard/hhkb/keymap.c` for sample.
+See `keyboards/hhkb/keymap.c` for sample.
} key_t;
***TODO: sample implementation***
-See `keyboard/hhkb/keymap.c` for sample.
+See `keyboards/hhkb/keymap.c` for sample.
+### 2.6 Swap-Hands Action
+The swap-hands action allows support for one-handed keyboards without requiring a separate layer. Set `ONEHAND_ENABLE` in the Makefile and define a `hand_swap_config` entry in your keymap. Now whenever the `ACTION_SWAP_HANDS` command key is pressed the keyboard is mirrored. For instance, to type "Hello, World" on QWERTY you would type `^Ge^s^s^w^c W^wr^sd`
+
+### 2.6.1 Configuration
+The configuration table is a simple 2-dimensional array to map from column/row to new column/row. Example `hand_swap_config` for Planck:
+
+```
+const keypos_t hand_swap_config[MATRIX_ROWS][MATRIX_COLS] = {
+ {{11, 0}, {10, 0}, {9, 0}, {8, 0}, {7, 0}, {6, 0}, {5, 0}, {4, 0}, {3, 0}, {2, 0}, {1, 0}, {0, 0}},
+ {{11, 1}, {10, 1}, {9, 1}, {8, 1}, {7, 1}, {6, 1}, {5, 1}, {4, 1}, {3, 1}, {2, 1}, {1, 1}, {0, 1}},
+ {{11, 2}, {10, 2}, {9, 2}, {8, 2}, {7, 2}, {6, 2}, {5, 2}, {4, 2}, {3, 2}, {2, 2}, {1, 2}, {0, 2}},
+ {{11, 3}, {10, 3}, {9, 3}, {8, 3}, {7, 3}, {6, 3}, {5, 3}, {4, 3}, {3, 3}, {2, 3}, {1, 3}, {0, 3}},
+};
+```
+
+Note that the array indices are reversed same as the matrix and the values are of type `keypos_t` which is `{col, row}` and all values are zero-based. In the example above, `hand_swap_config[2][4]` (third row, fifth column) would return {7, 2} (third row, eighth column).
+
+### 2.6.2 Advanced Swap Commands
+- **`ACTION_SWAP_HANDS()`** Swaps hands when pressed, returns to normal when released (momentary).
+- **`ACTION_SWAP_HANDS_TOGGLE()`** Toggles swap on and off with every keypress.
+- **`ACTION_SWAP_HANDS_TAP_TOGGLE()`** Toggles with a tap; momentary when held.
+- **`ACTION_SWAP_HANDS_TAP_KEY(key)`** Sends `key` with a tap; momentary swap when held.
+- **`ACTION_SWAP_HANDS_ON_OFF()`** Alias for `ACTION_SWAP_HANDS()`
+- **`ACTION_SWAP_HANDS_OFF_ON()`** Momentarily turns off swap.
+- **`ACTION_SWAP_HANDS_ON()`** Turns on swapping and leaves it on.
+- **`ACTION_SWAP_HANDS_OFF()`** Turn off swapping and leaves it off. Good for returning to a known state.
+
+
+
## 3. Layer switching Example
There are some ways to switch layer with 'Layer' actions.
### 4.3 Oneshot Modifier
-This runs onetime effects which modify only on just one following key. It works as normal modifier key when holding down while oneshot modifier when tapping.
+This runs onetime effects which modify only on just one following key. It works as normal modifier key when holding down while oneshot modifier when tapping. The behavior of oneshot modifiers is similar to the [sticky keys](https://en.wikipedia.org/wiki/StickyKeys) functionality found in most operating systems.
ACTION_MODS_ONESHOT(MOD_LSFT)
+Oneshot layer key:
+
+ ACTION_LAYER_ONESHOT(MY_LAYER)
+
Say you want to type 'The', you have to push and hold Shift key before type 't' then release it before type 'h' and 'e', otherwise you'll get 'THe' or 'the' unintentionally. With Oneshot Modifier you can tap Shift then type 't', 'h' and 'e' normally, you don't need to holding Shift key properly here. This mean you can release Shift before 't' is pressed down.
Oneshot effect is cancel unless following key is pressed down within `ONESHOT_TIMEOUT` of `config.h`. No timeout when it is `0` or not defined.
+Most implementations of sticky keys allow you to lock a modifier by double tapping the modifier. The layer then remains locked untill the modifier is tapped again. To enable this behaviour for oneshot modifiers set `ONESHOT_TAP_TOGGLE` to the number taps required. The feature is disabled if `ONESHOT_TAP_TOGGLE<2` or not defined.
+
### 4.4 Tap Toggle Mods
Similar to layer tap toggle, this works as a momentary modifier when holding, but toggles on with several taps. A single tap will 'unstick' the modifier again.