Merge branch 'rhaberkorn-serial-mouse'

[tmk_firmware.git] / converter / x68k_usb / config_pjrc.h

diff --git a/converter/x68k_usb/config_pjrc.h b/converter/x68k_usb/config_pjrc.h
index 20758bf2496f4798a5df0fe8ab31209d2b96e01a..c49b4a73e1de9446ec38b59f4304ca3c0ff8714e 100644 (file)
--- a/converter/x68k_usb/config_pjrc.h
+++ b/converter/x68k_usb/config_pjrc.h
@@ -18,8 +18,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #ifndef CONFIG_H
 #define CONFIG_H
 
-/* controller configuration */
-#include "controller_teensy.h"
 
 #define VENDOR_ID       0xFEED
 #define PRODUCT_ID      0x6800
@@ -35,29 +33,32 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 /* key combination for command */
 #define IS_COMMAND() ( \
-    keyboard_report->mods == (MOD_BIT(KB_LALT) | MOD_BIT(KB_RALT)) || \
-    keyboard_report->mods == (MOD_BIT(KB_LCTRL) | MOD_BIT(KB_RSHIFT)) \
+    keyboard_report->mods == (MOD_BIT(KC_LALT) | MOD_BIT(KC_RALT)) || \
+    keyboard_report->mods == (MOD_BIT(KC_LGUI) | MOD_BIT(KC_RGUI)) || \
+    keyboard_report->mods == (MOD_BIT(KC_LCTL) | MOD_BIT(KC_RCTL)) \
 )
 
-
-/* mouse keys */
-#ifdef MOUSEKEY_ENABLE
-#   define MOUSEKEY_DELAY_TIME 255
-#endif
+/* legacy keymap support */
+#define USE_LEGACY_KEYMAP
 
 
 /* USART configuration
  *     asynchronous, 2400baud, 8-data bit, non parity, 1-stop bit, no flow control
  */
 #ifdef __AVR_ATmega32U4__
-#   define KBD_RX_VECT        USART1_RX_vect
-#   define KBD_RX_DATA        UDR1
-#   define KBD_RX_BAUD        2400
-#   define KBD_RX_UBBR        ((F_CPU/(16UL*KBD_RX_BAUD))-1)
-#   define KBD_RX_INIT()      do { \
-        UBRR1L = (uint8_t) KBD_RX_UBBR; \
-        UBRR1H = (uint8_t) (KBD_RX_UBBR>>8); \
-        UCSR1B |= (1<<RXCIE1) | (1<<RXEN1); \
+    #define SERIAL_UART_BAUD       2400
+    #define SERIAL_UART_DATA       UDR1
+    #define SERIAL_UART_UBRR       ((F_CPU/(16UL*SERIAL_UART_BAUD))-1)
+    #define SERIAL_UART_RXD_VECT   USART1_RX_vect
+    #define SERIAL_UART_TXD_READY  (UCSR1A&(1<<UDRE1))
+    #define SERIAL_UART_INIT()     do { \
+        UBRR1L = (uint8_t) SERIAL_UART_UBRR;       /* baud rate */ \
+        UBRR1H = (uint8_t) (SERIAL_UART_UBRR>>8);  /* baud rate */ \
+        UCSR1B = (1<<RXCIE1) | (1<<RXEN1) | /* RX: interrupt, RX: enable */ \
+                 (1<<TXEN1);                /* TX: enable */ \
+        UCSR1C = (0<<UPM11) | (0<<UPM10) | /* parity: none(00), even(01), odd(11) */ \
+                 (0<<UCSZ12) | (1<<UCSZ11) | (1<<UCSZ10); /* data-8bit(011) */ \
+        sei(); \
     } while(0)
 #else
 #   error "USART configuration is needed."