Added bluefruit protocol and converter for 70% M

[tmk_firmware.git] / converter / terminal_bluefruit / config.h

diff --git a/converter/terminal_bluefruit/config.h b/converter/terminal_bluefruit/config.h
new file mode 100644 (file)
index 0000000..8bf139d
--- /dev/null
+++ b/converter/terminal_bluefruit/config.h
@@ -0,0 +1,112 @@
+/*
+Converter for 70% IBM Terminal Keyboard
+Author: Benjamin Gould, 2013
+Based on code Copyright 2011 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6535
+#define DEVICE_VER      0x0100
+#define MANUFACTURER    t.m.k.
+#define PRODUCT         70% IBM Terminal Keyboard Converter w/ Bluetooth
+#define DESCRIPTION     USB converter for IBM Terminal Keyboard w/ Bluetooth
+
+
+/* matrix size */
+#define MATRIX_ROWS 17  // keycode bit: 3-0
+#define MATRIX_COLS 8   // keycode bit: 6-4
+
+
+/* legacy keymap support */
+// #define USE_LEGACY_KEYMAP
+
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+    (keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT))) || \
+    (keyboard_report->mods == (MOD_BIT(KC_RALT) | MOD_BIT(KC_RCTL)))  \
+)
+
+/* USART configuration
+ *     asynchronous, 9600baud, 8-data bit, non parity, 1-stop bit, no flow control
+ */
+#ifdef __AVR_ATmega32U4__
+    #define SERIAL_UART_BAUD       9600
+    #define SERIAL_UART_DATA       UDR1
+    #define SERIAL_UART_UBRR       ((F_CPU/(16UL*SERIAL_UART_BAUD))-1)
+    #define SERIAL_UART_RXD_VECT   USART1_RX_vect
+    #define SERIAL_UART_TXD_READY  (UCSR1A&(1<<UDRE1))
+    #define SERIAL_UART_INIT()     do { \
+        UBRR1L = (uint8_t) SERIAL_UART_UBRR;       /* baud rate */ \
+        UBRR1H = (uint8_t) (SERIAL_UART_UBRR>>8);  /* baud rate */ \
+        UCSR1B = (1<<TXEN1);                /* TX: enable */ \
+        UCSR1C = (0<<UPM11) | (0<<UPM10) | /* parity: none(00), even(01), odd(11) */ \
+                 (0<<UCSZ12) | (1<<UCSZ11) | (1<<UCSZ10); /* data-8bit(011) */ \
+        sei(); \
+    } while(0)
+#else
+#   error "USART configuration is needed."
+#endif
+
+/*
+ * PS/2 Interrupt configuration
+ */
+#ifdef PS2_USE_INT
+/* uses INT1 for clock line(ATMega32U4) */
+#define PS2_CLOCK_PORT  PORTD
+#define PS2_CLOCK_PIN   PIND
+#define PS2_CLOCK_DDR   DDRD
+#define PS2_CLOCK_BIT   1
+
+#define PS2_DATA_PORT   PORTD
+#define PS2_DATA_PIN    PIND
+#define PS2_DATA_DDR    DDRD
+#define PS2_DATA_BIT    0
+
+#define PS2_INT_INIT()  do {    \
+    EICRA |= ((1<<ISC11) |      \
+              (0<<ISC10));      \
+} while (0)
+#define PS2_INT_ON()  do {      \
+    EIMSK |= (1<<INT1);         \
+} while (0)
+#define PS2_INT_OFF() do {      \
+    EIMSK &= ~(1<<INT1);        \
+} while (0)
+#define PS2_INT_VECT    INT1_vect
+#endif
+
+
+/*
+ * PS/2 Busywait configuration
+ */
+#ifdef PS2_USE_BUSYWAIT
+#define PS2_CLOCK_PORT  PORTD
+#define PS2_CLOCK_PIN   PIND
+#define PS2_CLOCK_DDR   DDRD
+#define PS2_CLOCK_BIT   1
+
+#define PS2_DATA_PORT   PORTD
+#define PS2_DATA_PIN    PIND
+#define PS2_DATA_DDR    DDRD
+#define PS2_DATA_BIT    0
+#endif
+
+#endif