cleans up folder structure

[qmk_firmware.git] / converter / ps2_usb / Makefile.tmk_rev1

diff --git a/converter/ps2_usb/Makefile.tmk_rev1 b/converter/ps2_usb/Makefile.tmk_rev1
deleted file mode 100644 (file)
index 6aaef49..0000000
--- a/converter/ps2_usb/Makefile.tmk_rev1
+++ /dev/null
@@ -1,98 +0,0 @@
-# 
-# Makefile for TMK keyboard converter rev2
-#     https://github.com/tmk/keyboard_converter#pcb-rev1
-#
-# Target file name (without extension).
-TARGET = ps2_usb_tmk_rev1
-
-# Directory common source filess exist
-TMK_DIR = ../../tmk_core
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# project specific files
-SRC =  keymap_common.c \
-       matrix.c \
-       led.c
-
-ifdef KEYMAP
-    SRC := keymap_$(KEYMAP).c $(SRC)
-else
-    SRC := keymap_plain.c $(SRC)
-endif
-
-CONFIG_H = config_tmk_rev1.h
-
-
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-#BOOTMAGIC_ENABLE = yes        # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes  # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes  # Audio control and System control(+450)
-CONSOLE_ENABLE = yes   # Console for debug(+400)
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-#NKRO_ENABLE = yes     # USB Nkey Rollover - not yet supported in LUFA
-
-
-# PS/2 Options
-#
-PS2_USE_USART = yes    # uses hardware USART engine for PS/2 signal receive(recomened)
-#PS2_USE_BUSYWAIT = yes        # uses primitive reference code
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TMK_DIR)
-
-include $(TMK_DIR)/protocol.mk
-include $(TMK_DIR)/protocol/lufa.mk
-include $(TMK_DIR)/common.mk
-include $(TMK_DIR)/rules.mk