Merge branch 'rhaberkorn-serial-mouse'

[tmk_firmware.git] / common / bootloader.c

diff --git a/common/bootloader.c b/common/bootloader.c
index cb971c7043771fbcbde4849c1e92bd5757387176..cda295b1811e92f90baea342084b37a07139bcc1 100644 (file)
--- a/common/bootloader.c
+++ b/common/bootloader.c
@@ -1,34 +1,107 @@
+#include <stdint.h>
+#include <stdbool.h>
 #include <avr/io.h>
 #include <avr/interrupt.h>
+#include <avr/wdt.h>
 #include <util/delay.h>
 #include "bootloader.h"
 
-/* Start Bootloader from Application
- * See 
- * http://www.pjrc.com/teensy/jump_to_bootloader.html
- * http://www.fourwalledcubicle.com/files/LUFA/Doc/120219/html/_page__software_bootloader_start.html
+#ifdef PROTOCOL_LUFA
+#include <LUFA/Drivers/USB/USB.h>
+#endif
+
+
+/* Boot Section Size in *BYTEs*
+ *   Teensy   halfKay    512
+ *   Teensy++ halfKay    1024
+ *   Atmel DFU loader    4096
+ *   LUFA bootloader     4096
+ *   USBaspLoader        2048
  */
+#ifndef BOOTLOADER_SIZE
+#warning To use bootloader_jump() you need to define BOOTLOADER_SIZE in config.h.
+#define BOOTLOADER_SIZE     4096
+#endif
 
-/* Boot Section Size in bytes
- * Teensy halfKay   512
- * Atmel DFU loader 4096
- * LUFA bootloader  4096
+#define FLASH_SIZE          (FLASHEND + 1L)
+#define BOOTLOADER_START    (FLASH_SIZE - BOOTLOADER_SIZE)
+
+
+/* 
+ * Entering the Bootloader via Software 
+ * http://www.fourwalledcubicle.com/files/LUFA/Doc/120730/html/_page__software_bootloader_start.html
  */
-#ifndef BOOT_SIZE
-#define BOOT_SIZE 512
+#define BOOTLOADER_RESET_KEY 0xB007B007
+uint32_t reset_key  __attribute__ ((section (".noinit")));
+
+/* initialize MCU status by watchdog reset */
+void bootloader_jump(void) {
+#ifdef PROTOCOL_LUFA
+    USB_Disable();
+    cli();
+    _delay_ms(2000);
 #endif
 
-#define FLASH_SIZE          (FLASHEND + 1)
-#define BOOTLOADER_START    (FLASHEND - BOOT_SIZE)
+#ifdef PROTOCOL_PJRC
+    cli();
+    UDCON = 1;
+    USBCON = (1<<FRZCLK);
+    UCSR1B = 0;
+    _delay_ms(5);
+#endif
+
+    // watchdog reset
+    reset_key = BOOTLOADER_RESET_KEY;
+    wdt_enable(WDTO_250MS);
+    for (;;);
+}
+
 
+/* this runs before main() */
+void bootloader_jump_after_watchdog_reset(void) __attribute__ ((used, naked, section (".init3")));
+void bootloader_jump_after_watchdog_reset(void)
+{
+    if ((MCUSR & (1<<WDRF)) && reset_key == BOOTLOADER_RESET_KEY) {
+        reset_key = 0;
+
+        // My custom USBasploader requires this to come up.
+        MCUSR = 0;
+
+        // Seems like Teensy halfkay loader requires clearing WDRF and disabling watchdog.
+        MCUSR &= ~(1<<WDRF);
+        wdt_disable();
+
+        // This is compled into 'icall', address should be in word unit, not byte.
+        ((void (*)(void))(BOOTLOADER_START/2))();
+    }
+}
+
+
+#if 0
+/* Jumping To The Bootloader
+ * http://www.pjrc.com/teensy/jump_to_bootloader.html
+ * 
+ * This method doen't work when using LUFA. idk why.
+ * - needs to initialize more regisers or interrupt setting?
+ */
 void bootloader_jump(void) {
+#ifdef PROTOCOL_LUFA
+    USB_Disable();
+    cli();
+    _delay_ms(2000);
+#endif
+
+#ifdef PROTOCOL_PJRC
     cli();
-    // disable watchdog, if enabled
-    // disable all peripherals
     UDCON = 1;
-    USBCON = (1<<FRZCLK);  // disable USB
+    USBCON = (1<<FRZCLK);
     UCSR1B = 0;
     _delay_ms(5);
+#endif
+
+    /*
+     * Initialize
+     */
 #if defined(__AVR_AT90USB162__)
     EIMSK = 0; PCICR = 0; SPCR = 0; ACSR = 0; EECR = 0;
     TIMSK0 = 0; TIMSK1 = 0; UCSR1B = 0;
@@ -51,6 +124,25 @@ void bootloader_jump(void) {
     PORTA = 0; PORTB = 0; PORTC = 0; PORTD = 0; PORTE = 0; PORTF = 0;
 #endif
 
-    // start Bootloader
-    ((void (*)(void))BOOTLOADER_START)();
+    /*
+     * USBaspLoader
+     */
+#if defined(__AVR_ATmega168__) || defined(__AVR_ATmega168P__) || defined(__AVR_ATmega328P__)
+    // This makes custom USBasploader come up.
+    MCUSR = 0;
+
+    // initialize ports
+    PORTB = 0; PORTC= 0; PORTD = 0;
+    DDRB = 0; DDRC= 0; DDRD = 0;
+
+    // disable interrupts
+    EIMSK = 0; EECR = 0; SPCR = 0;
+    ACSR = 0; SPMCSR = 0; WDTCSR = 0; PCICR = 0;
+    TIMSK0 = 0; TIMSK1 = 0; TIMSK2 = 0;
+    ADCSRA = 0; TWCR = 0; UCSR0B = 0;
+#endif
+
+    // This is compled into 'icall', address should be in word unit, not byte.
+    ((void (*)(void))(BOOTLOADER_START/2))();
 }
+#endif