2 ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
4 Licensed under the Apache License, Version 2.0 (the "License");
5 you may not use this file except in compliance with the License.
6 You may obtain a copy of the License at
8 http://www.apache.org/licenses/LICENSE-2.0
10 Unless required by applicable law or agreed to in writing, software
11 distributed under the License is distributed on an "AS IS" BASIS,
12 WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
13 See the License for the specific language governing permissions and
14 limitations under the License.
24 #define BOARD_NAME "JM60 keyboard"
29 #define STM32_LSECLK 32768
30 #define STM32_HSECLK 8000000
33 * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
35 * Only xB (128KB Flash) is defined, but it's identical to the
36 * x8 version (64KB Flash) except for the Flash region size in the
37 * linker script. For x8 parts use xB here and change to the x8 linker
38 * script in the project Makefile.
45 * numbering is sorted by onboard/connectors, as from the schematics in
46 * http://www.vcc-gnd.com/read.php?tid=369
50 #define GPIOA_USBDM 11 // pin 8
51 #define GPIOA_USBDP 12 // pin 9
53 #define GPIOC_OSC32_IN 14
54 #define GPIOC_OSC32_OUT 15
57 * I/O ports initial setup, this configuration is established soon after reset
58 * in the initialization code.
60 * The digits have the following meaning:
62 * 1 - Push Pull output 10MHz.
63 * 2 - Push Pull output 2MHz.
64 * 3 - Push Pull output 50MHz.
66 * 5 - Open Drain output 10MHz.
67 * 6 - Open Drain output 2MHz.
68 * 7 - Open Drain output 50MHz.
69 * 8 - Digital input with PullUp or PullDown resistor depending on ODR.
70 * 9 - Alternate Push Pull output 10MHz.
71 * A - Alternate Push Pull output 2MHz.
72 * B - Alternate Push Pull output 50MHz.
74 * D - Alternate Open Drain output 10MHz.
75 * E - Alternate Open Drain output 2MHz.
76 * F - Alternate Open Drain output 50MHz.
77 * Please refer to the STM32 Reference Manual for details.
82 * Everything input with pull-up except:
84 #define VAL_GPIOACRL 0x88888888 /* PA7...PA0 */
85 #define VAL_GPIOACRH 0x88888888 /* PA15...PA8 */
86 #define VAL_GPIOAODR 0xFFFFFFFF
90 * Everything input with pull-up except:
92 #define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */
93 #define VAL_GPIOBCRH 0x88888888 /* PB15...PB8 */
94 #define VAL_GPIOBODR 0xFFFFFFFF
98 * Everything input with pull-up except:
100 #define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
101 #define VAL_GPIOCCRH 0x88888888 /* PC15...PC8 */
102 #define VAL_GPIOCODR 0xFFFFFFFF
106 * Everything input with pull-up except:
107 * PD0 - Normal input (XTAL).
108 * PD1 - Normal input (XTAL).
110 #define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
111 #define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
112 #define VAL_GPIODODR 0xFFFFFFFF
116 * Everything input with pull-up except:
118 #define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
119 #define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
120 #define VAL_GPIOEODR 0xFFFFFFFF
123 * USB bus activation macro, required by the USB driver.
125 #define usb_lld_connect_bus(usbp) /* always connected */
128 * USB bus de-activation macro, required by the USB driver.
130 #define usb_lld_disconnect_bus(usbp) /* always connected */
132 #if !defined(_FROM_ASM_)
136 void boardInit(void);
140 #endif /* _FROM_ASM_ */
142 #endif /* _BOARD_H_ */