3 # project specific files
10 # This will define a symbol, F_CPU, in all source code files equal to the
11 # processor frequency in Hz. You can then use this symbol in your source code to
12 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
13 # automatically to create a 32-bit value in your source code.
15 # This will be an integer division of F_USB below, as it is sourced by
16 # F_USB after it has run through any CPU prescalers. Note that this value
17 # does not *change* the processor frequency - it should merely be updated to
18 # reflect the processor speed set externally so that the code can use accurate
26 # Target architecture (see library "Board Types" documentation).
29 # Input clock frequency.
30 # This will define a symbol, F_USB, in all source code files equal to the
31 # input clock frequency (before any prescaling is performed) in Hz. This value may
32 # differ from F_CPU if prescaling is used on the latter, and is required as the
33 # raw input clock is fed directly to the PLL sections of the AVR for high speed
34 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
35 # at the end, this will be done automatically to create a 32-bit value in your
38 # If no clock division is performed on the input clock inside the AVR (via the
39 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
42 # Interrupt driven control endpoint task(+60)
43 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
46 # Boot Section Size in *bytes*
48 # Teensy++ halfKay 1024
49 # Atmel DFU loader 4096
50 # LUFA bootloader 4096
52 #OPT_DEFS += -DBOOTLOADER_SIZE=4096
54 # as per original hasu settings
55 OPT_DEFS += -DBOOTLOADER_SIZE=4096
58 # comment out to disable the options.
60 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
61 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
62 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
63 CONSOLE_ENABLE = yes # Console for debug(+400)
64 COMMAND_ENABLE = yes # Commands for debug and configuration
65 CUSTOM_MATRIX = yes # Custom matrix file for the HHKB
66 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
67 # SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
68 # NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
69 # BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
70 # MIDI_ENABLE = yes # MIDI controls
71 # UNICODE_ENABLE = yes # Unicode
72 # BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
75 # HHKB_RN42_ENABLE = yes # Enable support for hasu's BT alt controller -- code borrowed from tmk source tree.
77 # Either uncomment the HHKB_RN42_ENABLE line above, or run make enabling the
78 # feature. Be sure to clean any existing build before trying to enable rn42
79 # support. For example:
81 # make hhkb-keymap-clean
82 # make hhkb-keymap-dfu HHKB_RN42_ENABLE=yes
84 ifeq ($(strip $(HHKB_RN42_ENABLE)), yes)
86 OPT_DEFS += -DHHKB_RN42_ENABLE
88 # Support for the RN42 Bluetooth module. This is the BT module in Hasu's BT
89 # HHKB Alt controller.
92 SRC += serial_uart.c \
104 # debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
107 # debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
108 # debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS))