1 #----------------------------------------------------------------------------
4 # make all = Make software.
6 # make clean = Clean out built project files.
8 # make coff = Convert ELF to AVR COFF.
10 # make extcoff = Convert ELF to AVR Extended COFF.
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
33 # make filename.s = Just compile filename.c into the assembler code only.
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
41 # Target file name (without extension).
44 # Directory common source filess exist
47 # Directory keyboard dependent files exist
50 # Default to PCB matrix
55 $(warning MATRIX: $(MATRIX))
57 # # project specific files
60 SRC = keymap_common.c \
66 SRC := common_keymaps/keymap_$(KEYMAP).c $(SRC)
68 SRC := common_keymaps/keymap_jack.c $(SRC)
73 SRC = extended_keymap_common.c \
79 SRC := extended_keymaps/extended_keymap_$(KEYMAP).c $(SRC)
81 SRC := extended_keymaps/extended_keymap_default.c $(SRC)
92 # Processor frequency.
93 # This will define a symbol, F_CPU, in all source code files equal to the
94 # processor frequency in Hz. You can then use this symbol in your source code to
95 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
96 # automatically to create a 32-bit value in your source code.
98 # This will be an integer division of F_USB below, as it is sourced by
99 # F_USB after it has run through any CPU prescalers. Note that this value
100 # does not *change* the processor frequency - it should merely be updated to
101 # reflect the processor speed set externally so that the code can use accurate
109 # Target architecture (see library "Board Types" documentation).
112 # Input clock frequency.
113 # This will define a symbol, F_USB, in all source code files equal to the
114 # input clock frequency (before any prescaling is performed) in Hz. This value may
115 # differ from F_CPU if prescaling is used on the latter, and is required as the
116 # raw input clock is fed directly to the PLL sections of the AVR for high speed
117 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
118 # at the end, this will be done automatically to create a 32-bit value in your
121 # If no clock division is performed on the input clock inside the AVR (via the
122 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
125 # Interrupt driven control endpoint task(+60)
126 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
129 # Boot Section Size in *bytes*
131 # Teensy++ halfKay 1024
132 # Atmel DFU loader 4096
133 # LUFA bootloader 4096
135 OPT_DEFS += -DBOOTLOADER_SIZE=4096
139 # comment out to disable the options.
141 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
142 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
143 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
144 CONSOLE_ENABLE = yes # Console for debug(+400)
145 COMMAND_ENABLE = yes # Commands for debug and configuration
146 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
147 #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
148 NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
149 BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
151 # Optimize size but this may cause error "relocation truncated to fit"
152 #EXTRALDFLAGS = -Wl,--relax
155 VPATH += $(TARGET_DIR)
158 include $(TOP_DIR)/protocol/lufa.mk
159 include $(TOP_DIR)/common.mk
160 include $(TOP_DIR)/rules.mk