]> git.donarmstrong.com Git - qmk_firmware.git/blob - keyboard/planck/Makefile
matrix
[qmk_firmware.git] / keyboard / planck / Makefile
1 #----------------------------------------------------------------------------
2 # On command line:
3 #
4 # make all = Make software.
5 #
6 # make clean = Clean out built project files.
7 #
8 # make coff = Convert ELF to AVR COFF.
9 #
10 # make extcoff = Convert ELF to AVR Extended COFF.
11 #
12 # make program = Download the hex file to the device.
13 #                Please customize your programmer settings(PROGRAM_CMD)
14 #
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 #               (must have teensy_loader_cli installed).
17 #
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 #            have dfu-programmer installed).
20 #
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 #             have Atmel FLIP installed).
23 #
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 #               (must have dfu-programmer installed).
26 #
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 #                (must have Atmel FLIP installed).
29 #
30 # make debug = Start either simulavr or avarice as specified for debugging, 
31 #              with avr-gdb or avr-insight as the front end for debugging.
32 #
33 # make filename.s = Just compile filename.c into the assembler code only.
34 #
35 # make filename.i = Create a preprocessed source file for use in submitting
36 #                   bug reports to the GCC project.
37 #
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
40
41 # Target file name (without extension).
42 TARGET = planck_lufa
43
44 # Directory common source filess exist
45 TOP_DIR = ../..
46
47 # Directory keyboard dependent files exist
48 TARGET_DIR = .
49
50 # Default to PCB matrix
51 ifndef MATRIX
52         MATRIX=matrix_pcb.c
53 endif
54
55 $(warning MATRIX: $(MATRIX))
56
57 # # project specific files
58 ifdef COMMON
59
60         SRC = keymap_common.c \
61         $(MATRIX) \
62         led.c \
63         backlight.c \
64         beeps.c 
65
66 ifdef KEYMAP
67     SRC := common_keymaps/keymap_$(KEYMAP).c $(SRC)
68 else
69     SRC := common_keymaps/keymap_jack.c $(SRC)
70 endif
71
72 else
73
74 SRC = extended_keymap_common.c \
75         $(MATRIX) \
76         led.c \
77         backlight.c \
78         beeps.c 
79
80 ifdef KEYMAP
81     SRC := extended_keymaps/extended_keymap_$(KEYMAP).c $(SRC)
82 else
83     SRC := extended_keymaps/extended_keymap_default.c $(SRC)
84 endif
85
86 endif
87
88 CONFIG_H = config.h
89
90 # MCU name
91 #MCU = at90usb1287
92 MCU = atmega32u4
93
94 # Processor frequency.
95 #     This will define a symbol, F_CPU, in all source code files equal to the
96 #     processor frequency in Hz. You can then use this symbol in your source code to
97 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
98 #     automatically to create a 32-bit value in your source code.
99 #
100 #     This will be an integer division of F_USB below, as it is sourced by
101 #     F_USB after it has run through any CPU prescalers. Note that this value
102 #     does not *change* the processor frequency - it should merely be updated to
103 #     reflect the processor speed set externally so that the code can use accurate
104 #     software delays.
105 F_CPU = 16000000
106
107
108 #
109 # LUFA specific
110 #
111 # Target architecture (see library "Board Types" documentation).
112 ARCH = AVR8
113
114 # Input clock frequency.
115 #     This will define a symbol, F_USB, in all source code files equal to the
116 #     input clock frequency (before any prescaling is performed) in Hz. This value may
117 #     differ from F_CPU if prescaling is used on the latter, and is required as the
118 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
119 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
120 #     at the end, this will be done automatically to create a 32-bit value in your
121 #     source code.
122 #
123 #     If no clock division is performed on the input clock inside the AVR (via the
124 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
125 F_USB = $(F_CPU)
126
127 # Interrupt driven control endpoint task(+60)
128 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
129
130
131 # Boot Section Size in *bytes*
132 #   Teensy halfKay   512
133 #   Teensy++ halfKay 1024
134 #   Atmel DFU loader 4096
135 #   LUFA bootloader  4096
136 #   USBaspLoader     2048
137 OPT_DEFS += -DBOOTLOADER_SIZE=4096
138
139
140 # Build Options
141 #   comment out to disable the options.
142 #
143 BOOTMAGIC_ENABLE = yes  # Virtual DIP switch configuration(+1000)
144 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
145 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
146 CONSOLE_ENABLE = yes    # Console for debug(+400)
147 COMMAND_ENABLE = yes    # Commands for debug and configuration
148 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
149 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
150 NKRO_ENABLE = yes       # USB Nkey Rollover - not yet supported in LUFA
151 BACKLIGHT_ENABLE = yes  # Enable keyboard backlight functionality
152
153 # Optimize size but this may cause error "relocation truncated to fit"
154 #EXTRALDFLAGS = -Wl,--relax
155
156 # Search Path
157 VPATH += $(TARGET_DIR)
158 VPATH += $(TOP_DIR)
159
160 include $(TOP_DIR)/protocol/lufa.mk
161 include $(TOP_DIR)/common.mk
162 include $(TOP_DIR)/rules.mk