1 #----------------------------------------------------------------------------
4 # make all = Make software.
6 # make clean = Clean out built project files.
8 # make coff = Convert ELF to AVR COFF.
10 # make extcoff = Convert ELF to AVR Extended COFF.
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
33 # make filename.s = Just compile filename.c into the assembler code only.
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
41 # Target file name (without extension).
45 # Directory common source filess exist
47 TMK_DIR = ../../tmk_core
49 # Directory keyboard dependent files exist
52 # # project specific files
56 SRC := keymaps/$(KEYMAP).c $(SRC)
58 SRC := keymaps/default.c $(SRC)
62 OPT_DEFS += -DATREUS_TEENSY2
63 ATRUES_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
65 OPT_DEFS += -DATREUS_ASTAR
66 ATRUES_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
67 avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
76 # Processor frequency.
77 # This will define a symbol, F_CPU, in all source code files equal to the
78 # processor frequency in Hz. You can then use this symbol in your source code to
79 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
80 # automatically to create a 32-bit value in your source code.
82 # This will be an integer division of F_USB below, as it is sourced by
83 # F_USB after it has run through any CPU prescalers. Note that this value
84 # does not *change* the processor frequency - it should merely be updated to
85 # reflect the processor speed set externally so that the code can use accurate
93 # Target architecture (see library "Board Types" documentation).
96 # Input clock frequency.
97 # This will define a symbol, F_USB, in all source code files equal to the
98 # input clock frequency (before any prescaling is performed) in Hz. This value may
99 # differ from F_CPU if prescaling is used on the latter, and is required as the
100 # raw input clock is fed directly to the PLL sections of the AVR for high speed
101 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
102 # at the end, this will be done automatically to create a 32-bit value in your
105 # If no clock division is performed on the input clock inside the AVR (via the
106 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
109 # Interrupt driven control endpoint task(+60)
110 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
113 # Boot Section Size in *bytes*
115 # Teensy++ halfKay 1024
116 # Atmel DFU loader 4096
117 # LUFA bootloader 4096
119 OPT_DEFS += -DBOOTLOADER_SIZE=4096
123 # comment out to disable the options.
125 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
126 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
127 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
128 CONSOLE_ENABLE = yes # Console for debug(+400)
129 COMMAND_ENABLE = yes # Commands for debug and configuration
130 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
131 # SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
132 NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
133 # BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
134 # MIDI_ENABLE = YES # MIDI controls
135 UNICODE_ENABLE = YES # Unicode
136 # BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
139 # Optimize size but this may cause error "relocation truncated to fit"
140 #EXTRALDFLAGS = -Wl,--relax
143 VPATH += $(TARGET_DIR)
147 include $(TOP_DIR)/quantum/quantum.mk
149 USB ?= /dev/cu.usbmodem1411
152 $(ATRUES_UPLOAD_COMMAND)