2 # Makefile for PJRC Teensy
6 # Target file name (without extension).
9 # Directory common source filess exist
12 # Directory keyboard dependent files exist
15 # keyboard dependent files
20 # protocol/serial_uart.c
22 CONFIG_H = config_pjrc.h
25 # MCU name, you MUST set this to match the board you are using
26 # type "make clean" after changing this, so all files will be rebuilt
27 #MCU = at90usb162 # Teensy 1.0
28 MCU = atmega32u4 # Teensy 2.0
29 #MCU = at90usb646 # Teensy++ 1.0
30 #MCU = at90usb1286 # Teensy++ 2.0
33 # Processor frequency.
34 # Normally the first thing your program should do is set the clock prescaler,
35 # so your program will run at the correct speed. You should also set this
36 # variable to same clock speed. The _delay_ms() macro uses this, and many
37 # examples use this variable to calculate timings. Do not add a "UL" here.
41 # Boot Section Size in bytes
43 # Atmel DFU loader 4096
44 # LUFA bootloader 4096
45 OPT_DEFS += -DBOOTLOADER_SIZE=4096
49 # *Comment out* to disable the options.
51 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
52 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
53 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
54 CONSOLE_ENABLE = yes # Console for debug(+400)
55 COMMAND_ENABLE = yes # Commands for debug and configuration
56 #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
57 #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
61 #---------------- Programming Options --------------------------
63 # Type: avrdude -c ? to get a full listing.
64 AVRDUDE_PROGRAMMER = avr109
65 AVRDUDE_PORT = /dev/ttyACM0
66 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
67 #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
69 # Uncomment the following if you want avrdude's erase cycle counter.
70 # Note that this counter needs to be initialized first using -Yn,
72 #AVRDUDE_ERASE_COUNTER = -y
74 # Uncomment the following if you do /not/ wish a verification to be
75 # performed after programming the device.
76 #AVRDUDE_NO_VERIFY = -V
78 # Increase verbosity level. Please use this when submitting bug
79 # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
80 # to submit bug reports.
81 #AVRDUDE_VERBOSE = -v -v
83 AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
84 #AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
85 AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
86 AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
87 AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
89 #PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
90 #PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
91 PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex
95 VPATH += $(TARGET_DIR)
99 include $(TOP_DIR)/protocol/pjrc.mk
100 include $(TOP_DIR)/protocol.mk
101 include $(TOP_DIR)/common.mk
102 include $(TOP_DIR)/rules.mk