]> git.donarmstrong.com Git - tmk_firmware.git/blob - ADB.txt
integrate V-USB support into ps2_usb
[tmk_firmware.git] / ADB.txt
1 ADB Protocol
2 ============
3
4 Resources
5 ---------
6 ADB - The Untold Story: Space Aliens Ate My Mouse
7     http://developer.apple.com/legacy/mac/library/#technotes/hw/hw_01.html
8 Apple IIgs Hardware Reference Second Edition [p80(Chapter6 p121)]
9     ftp://ftp.apple.asimov.net/pub/apple_II/documentation/Apple%20IIgs%20Hardware%20Reference.pdf
10 ADB Keycode
11     http://72.0.193.250/Documentation/macppc/adbkeycodes/
12     http://m0115.web.fc2.com/m0115.jpg
13     [Inside Macintosh volume V, pages 191-192]
14 ADB Signaling
15     http://kbdbabel.sourceforge.net/doc/kbd_signaling_pcxt_ps2_adb.pdf
16 ADB Overview & History
17     http://en.wikipedia.org/wiki/Apple_Desktop_Bus
18 Microchip Application Note: ADB device(with code for PIC16C)
19     http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1824&appnote=en011062
20 AVR ATtiny2131 ADB to PS/2 converter(Japanese)
21     http://hp.vector.co.jp/authors/VA000177/html/KeyBoardA5DEA5CBA5A2II.html
22
23
24 Pinouts
25 -------
26     ADB female socket from the front:
27     __________
28     |        | <--- top
29     | 4o  o3 |
30     |2o    o1|
31     |   ==   |
32     |________| <--- bottom
33       |    |   <--- 4pins
34
35
36     ADB female socket from bottom:
37
38     ========== <--- front
39     |        |
40     |        |
41     |2o    o1|
42     |4o    o3|
43     ---------- <--- back
44
45     1: Data
46     2: Power SW(low when press Power key)
47     3: Vcc(5V)
48     4: GND
49
50
51
52 Commands
53 --------
54     ADB command is 1byte and consists of 4bit-address, 2bit-command
55     type and 2bit-register. The commands are always sent by Host.
56
57     Command format:
58     7 6 5 4 3 2 1 0
59     | | | |------------ address
60             | |-------- command type
61                 | |---- register
62
63     bits                commands
64     ------------------------------------------------------
65     - - - - 0 0 0 0     Send Request(reset all devices)
66     A A A A 0 0 0 1     Flush(reset a device)
67     - - - - 0 0 1 0     Reserved
68     - - - - 0 0 1 1     Reserved
69     - - - - 0 1 - -     Reserved
70     A A A A 1 0 R R     Listen(write to a device)
71     A A A A 1 1 R R     Talk(read from a device)
72
73     The command to read keycodes from keyboard is 0x2C which
74     consist of keyboard address 2 and Talk against register 0. 
75
76     Address:
77     2:  keyboard
78     3:  mice
79
80     Registers:
81     0: application(keyobard uses this to store its data.)
82     1: application
83     2: application(keyboard uses this for LEDs and state of modifiers)
84     3: status and command
85
86
87 Communication
88 -------------
89     This is a minimum information for keyboard communication.
90     See "Resources" for detail.
91
92     Signaling:
93
94     ~~~~____________~~||||||||||||__~~~~~_~~|||||||||||||||__~~~~
95
96         |800us     |  |7 Command 0|  |   |  |15-64  Data  0|Stopbit(0)
97         +Attention |              |  |   +Startbit(1)
98                    +Startbit(1)   |  +Tlt(140-260us)
99                                   +stopbit(0)
100
101     Bit cells:
102
103     bit0: ______~~~
104           65    :35us
105
106     bit1: ___~~~~~~
107           35 :65us
108
109     bit0 low time: 60-70% of bit cell(42-91us)
110     bit1 low time: 30-40% of bit cell(21-52us)
111     bit cell time: 70-130us
112     [from Apple IIgs Hardware Reference Second Edition]
113
114     Criterion for bit0/1:
115     After 55us if line is low/high then bit is 0/1.
116
117     Attention & start bit:
118     Host asserts low in 560-1040us then places start bit(1).
119
120     Tlt(Stop to Start):
121     Bus stays high in 140-260us then device places start bit(1).
122
123     Global reset:
124     Host asserts low in 2.8-5.2ms. All devices are forced to reset.
125
126     Send request from device(Srq):
127     Device can request to send at commad(Global only?) stop bit.
128     keep low for 300us to request.
129
130
131 Keyboard Data(Register0)
132     This 16bit data can contains two keycodes and two released flags.
133     First keycode is palced in upper byte. When one keyocode is sent,
134     lower byte is 0xFF.
135     Release flag is 1 when key is released.
136
137     1514 . . . . . 8 7 6 . . . . . 0
138      | | | | | | | | | +-+-+-+-+-+-+-   Keycode2
139      | | | | | | | | +---------------   Released2(1 when the key is released)
140      | +-+-+-+-+-+-+-----------------   Keycode1
141      +-------------------------------   Released1(1 when the key is released)
142
143     Keycodes:
144     Scancode consists of 7bit keycode and 1bit release flag.
145     Device can send two keycodes at once. If just one keycode is sent
146     keycode1 contains it and keyocode2 is 0xFF.
147
148     Power switch:
149     You can read the state from PSW line(active low) however
150     the switch has a special scancode 0x7F7F, so you can
151     also read from Data line. It uses 0xFFFF for release scancode.
152
153 Keyboard LEDs & state of keys(Register2)
154     This register hold current state of three LEDs and nine keys.
155     The state of LEDs can be changed by sending Listen command.
156     
157     1514 . . . . . . 7 6 5 . 3 2 1 0
158      | | | | | | | | | | | | | | | +-   LED1(NumLock)
159      | | | | | | | | | | | | | | +---   LED2(CapsLock)
160      | | | | | | | | | | | | | +-----   LED3(ScrollLock)
161      | | | | | | | | | | +-+-+-------   Reserved
162      | | | | | | | | | +-------------   ScrollLock
163      | | | | | | | | +---------------   NumLock
164      | | | | | | | +-----------------   Apple/Command
165      | | | | | | +-------------------   Option
166      | | | | | +---------------------   Shift
167      | | | | +-----------------------   Control
168      | | | +-------------------------   Reset/Power
169      | | +---------------------------   CapsLock
170      | +-----------------------------   Delete
171      +-------------------------------   Reserved
172
173 END_OF_ADB