-This is a font of music symbols. All MF sources are original. Most
-of the documentation is in comments in the MF code.
+This is a font of music symbols. All MF sources are original. Most of the
+documentation is in comments in the MF code.
Non-square pixels are not supported; with other words, the horizontal and
vertical resolution of the output device must be the same.
Currently, outline fonts are created by using `autotrace', but we are
-already in the process to convert the MF code directly to PostScript code
+already in the process of converting the MF code directly to PostScript code
with a tool called `mf2pt1', which in turn calls `FontForge' to postprocess
the output (mainly to remove outline overlaps and to add hints).
The recommended calling sequence of mf2pt1 is
- mf2pt1 --rounding=0.001 <font>
+ mf2pt1 --rounding=0.0001 <other options> <font>
You need mf2pt1 version 2.1 or newer.
+
Here some guidelines to assure a clean conversion.
. Never use `---'. Replace it with `--' together with explicit path
directions (if necessary).
-. Don't use self-intersecting outlines in general since it can confuse
+. Don't use self-intersecting outlines in general since they can confuse
mf2pt1's algorithm to get the orientation of a closed path. Note that
MetaPost's implementation of the `turningnumber' primitive (which would
immediately give the orientation of a path) is severely broken before
to work around this bug.
. If outlines intersect, avoid grazing intersections. In case two outlines
- intersect in an explicitly defined point, include this point into both
+ intersect in an explicitly defined point, include this point in both
intersecting paths to avoid problems due to rounding errors.
. Don't use `draw' with a polygonal pen but for straight lines (consisting
overlaps.
+Some glyph name rules:
+
+. Most glyph names have the form <group>.<name>, where <group> is defined
+ with the `fet_begingroup' command, and <name> is given with
+ `fet_beginchar' (within a `fet_begingroup' block). Example:
+ `clefs.vaticana.fa'.
+
+. Sometimes it would be sensible to use negative numbers in glyph names.
+ However, the `-' character shouldn't be used in a glyph name. Replace it
+ with `M'. For example, write `rests.M3mensural' instead of
+ `rests.-3mensural'.
+
+. Glyphs which exist in both an `up' and `down' version should start the
+ <name> part with either `u' or `d', respectively. Example: `flags.d3',
+ `flags.u3'. Glyphs which are neutral w.r.t. the direction, and where
+ members of the glyph group exist which have `up' and `down' versions,
+ should start with an `s'. Example: `noteheads.s0re'.
+
+
Some design rules:
. Always use smooth curve transitions. Since this is difficult to see in
. Use rounded corners.
-Finally, some rules to assure that rasterization at low resolutions give
+Hints for stem attachment:
+
+. Stem attachment of glyphs is controlled by two special variables called
+ `charwx' and `charwy'. Stems can be regarded as (very oblonged)
+ rectangles with slightly rounded corners. For stems pointing upwards the
+ lower right corner of this rectangle is attached to the glyph at position
+ (charwx, charwy). For stems pointing downwards it works analogously but
+ with the upper left corner, where the position of the attachment point is
+ additionally reflected horizontally about the center of the glyph -- this
+ ensures that in most cases charwx and charwy can be set to the same values
+ for up and down stems even though these are attached at the right/left end
+ of the note, respectively. To make this more precise, the upper left
+ corner of a down stem is attached at position (charwd/2 - charwx, charwy),
+ where `charwd' is an internal metafont variable representing the glyph
+ width as specified by the `set_char_box' command.
+
+. In case different stem attachments for upward and downward pointing stems
+ are needed, two separate glyphs must be defined in the Metafont file; of
+ course, this also applies if two entirely different shapes are needed.
+ These have the same name but are prefixed by `u' and `d', respectively
+ (for `up' and `down', obviously). In each of these glyphs the variables
+ charwx and charwy must be set accordingly. If, on the other hand, the
+ attachment point is the `same' for both directions (with the
+ abovementioned horizontal reflection taken into account), then the prefix
+ `s' (for `symmetric') should be used. See the existing files for
+ examples. The numbers in the glyph names refer to the duration of the
+ note; e.g., `s0cross' in feta-noteheads.mf defines the notehead for a
+ whole cross-shaped note (similarly, `s1cross' and `s2cross' are for half
+ and quarter notes, respectively).
+
+
+Finally, some rules to assure that rasterization at low resolutions gives
good results. Today, this is a minor issue, but in some cases it might show
design flaws.