X-Git-Url: https://git.donarmstrong.com/?p=qmk_firmware.git;a=blobdiff_plain;f=keyboards%2Frgbkb%2Fsol%2Frules.mk;h=3be8f0b229147f5f4fc1273b92b3affd66b75bc5;hp=a3dcfc29030e7762b8735436b297bcc47e050a38;hb=40b0ddd425bf09ddbb15a414b5147e98256f10a8;hpb=17ff9cf554d64fd3e036f3d6e06cff952d8802bf

diff --git a/keyboards/rgbkb/sol/rules.mk b/keyboards/rgbkb/sol/rules.mk
index a3dcfc290..3be8f0b22 100644
--- a/keyboards/rgbkb/sol/rules.mk
+++ b/keyboards/rgbkb/sol/rules.mk
@@ -2,41 +2,15 @@
 MCU = atmega32u4
 
 # Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
 F_CPU = 16000000
 
-#
-# LUFA specific
-#
 # Target architecture (see library "Board Types" documentation).
 ARCH = AVR8
 
 # Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
 
 # Bootloader
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = qmk-dfu
 
 # Interrupt driven control endpoint task(+60)
@@ -48,18 +22,4 @@ OPT_DEFS += -DOLED_FONT_H=\"common/glcdfont.c\"
 SPLIT_KEYBOARD = yes
 ENCODER_ENABLE = yes
 
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in
-#   the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no         # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
-NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = yes       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-
-DEFAULT_FOLDER = rgbkb/sol/rev1
+DEFAULT_FOLDER = rgbkb/sol/rev2