SRC += matrix.c \ i2c.c \ split_util.c \ serial.c # MCU name #MCU = at90usb1287 MCU = atmega32u4 # Processor frequency. # This will define a symbol, F_CPU, in all source code files equal to the # processor frequency in Hz. You can then use this symbol in your source code to # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # # This will be an integer division of F_USB below, as it is sourced by # F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. F_CPU = 16000000 # # LUFA specific # # Target architecture (see library "Board Types" documentation). ARCH = AVR8 # Input clock frequency. # This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' # at the end, this will be done automatically to create a 32-bit value in your # source code. # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. F_USB = $(F_CPU) # Interrupt driven control endpoint task(+60) OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Boot Section Size in *bytes* # Teensy halfKay 512 # Teensy++ halfKay 1024 # Atmel DFU loader 4096 # LUFA bootloader 4096 # USBaspLoader 2048 OPT_DEFS += -DBOOTLOADER_SIZE=4096 # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically # BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) CONSOLE_ENABLE ?= no # Console for debug(+400) COMMAND_ENABLE ?= yes # Commands for debug and configuration NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality MIDI_ENABLE ?= no # MIDI controls AUDIO_ENABLE ?= no # Audio output on port C6 UNICODE_ENABLE ?= no # Unicode BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. SUBPROJECT_rev1 ?= yes USE_I2C ?= yes # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend CUSTOM_MATRIX = yes avrdude: build ls /dev/tty* > /tmp/1; \ echo "Reset your Pro Micro then hit any key to continue..."; \ read -n 1 -s; \ ls /dev/tty* > /tmp/2; \ USB=`diff /tmp/1 /tmp/2 | grep '>' | sed -e 's/> //'`; \ avrdude -p $(MCU) -c avr109 -P $$USB -U flash:w:$(BUILD_DIR)/$(TARGET).hex .PHONY: avrdude