From 00225b77e54fdc893f6c64768e1bffaa01df5849 Mon Sep 17 00:00:00 2001
From: MechMerlin <30334081+mechmerlin@users.noreply.github.com>
Date: Mon, 9 Sep 2019 21:57:45 -0700
Subject: [PATCH] [Keyboard] Waldo RGB Enable (#6711)

* enable rgb animations

* clean up code
---
 keyboards/waldo/config.h | 19 +++++++++++--------
 keyboards/waldo/rules.mk | 33 ---------------------------------
 2 files changed, 11 insertions(+), 41 deletions(-)

diff --git a/keyboards/waldo/config.h b/keyboards/waldo/config.h
index c913ae771..c3272bf1d 100644
--- a/keyboards/waldo/config.h
+++ b/keyboards/waldo/config.h
@@ -36,16 +36,12 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define UNUSED_PINS
 
 #define BACKLIGHT_PIN B7
+#define BACKLIGHT_BREATHING
+#define BACKLIGHT_LEVELS 3
 
 /* COL2ROW or ROW2COL */
 #define DIODE_DIRECTION COL2ROW
 
-/* define if matrix has ghost */
-//#define MATRIX_HAS_GHOST
-
-/* number of backlight levels */
-#define BACKLIGHT_LEVELS 3
-
 /* Set 0 if debouncing isn't needed */
 #define DEBOUNCE 5
 
@@ -73,5 +69,12 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 //#define NO_ACTION_FUNCTION
 
 // RGB LED
-#define RGB_DI_PIN B0     // The pin the LED strip is connected to
-#define RGBLED_NUM 10     // Number of LEDs in your strip
+#define RGB_DI_PIN B0
+#ifdef RGB_DI_PIN
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 10
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8
+#define RGBLIGHT_SLEEP
+#endif
\ No newline at end of file
diff --git a/keyboards/waldo/rules.mk b/keyboards/waldo/rules.mk
index 40ac48474..6b3a9b96c 100644
--- a/keyboards/waldo/rules.mk
+++ b/keyboards/waldo/rules.mk
@@ -1,45 +1,12 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
 # Bootloader
 #     This definition is optional, and if your keyboard supports multiple bootloaders of
 #     different sizes, comment this out, and the correct address will be loaded 
 #     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = atmel-dfu
 
-
 # Interrupt driven control endpoint task(+60)
 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 
-- 
2.39.5