ifdef TEENSY2
OPT_DEFS += -DATREUS_TEENSY2
- ATRUES_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
+ ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
else
OPT_DEFS += -DATREUS_ASTAR
OPT_DEFS += -DCATERINA_BOOTLOADER
- ATRUES_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
+ ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
endif
USB ?= /dev/cu.usbmodem1411
upload: build
- $(ATRUES_UPLOAD_COMMAND)
-
\ No newline at end of file
+ $(ATREUS_UPLOAD_COMMAND)
+
[_L1] = { /* LAYER 1 */
{KC_1, KC_2, KC_3, KC_4, KC_5, KC_NO, KC_6, KC_7, KC_8, KC_9, KC_0 },
{KC_TAB, KC_INS, KC_UP, KC_DEL, KC_HOME, KC_NO, KC_PGUP, KC_MUTE, KC_VOLD, KC_VOLU, KC_EQL },
- {KC_CAPS, KC_LEFT, KC_DOWN, KC_RGHT, KC_END, KC_LCTL, KC_PGDN, KC_MPRV, KC_MPLY, KC_MNXT, KC_BSLS},
+ {KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_END, KC_LCTL, KC_PGDN, KC_MPRV, KC_MPLY, KC_MNXT, KC_BSLS},
{KC_TRNS, KC_GRV, KC_LGUI, KC_TRNS, KC_DEL, KC_LALT, KC_SPC, KC_TRNS, KC_LBRC, KC_RBRC, KC_ENT }
},
[_L2] = { /* LAYER 2 */
{KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_NO, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN},
- {KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_NO, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10 },
- {KC_TRNS, KC_TRNS, DVORAK, QWERTY, COLEMAK, KC_LCTL, KC_TRNS, KC_TRNS, KC_TRNS, KC_F11, KC_F12 },
- {KC_TRNS, KC_TRNS, KC_LGUI, KC_TRNS, KC_BSPC, KC_LALT, KC_SPC, KC_TRNS, KC_TRNS, KC_TRNS, RESET }
+ {KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_NO, KC_TRNS, KC_F6, KC_F7, KC_F8, KC_PLUS},
+ {KC_TRNS, KC_TRNS, DVORAK, QWERTY, COLEMAK, KC_LCTL, KC_TRNS, KC_F9, KC_F10, KC_F11, KC_F12 },
+ {KC_TRNS, KC_TRNS, KC_LGUI, KC_TRNS, KC_BSPC, KC_LALT, KC_SPC, KC_TRNS, LSFT(KC_LBRC), LSFT(KC_RBRC), RESET}
}
};
--- /dev/null
+/*
+ * The Dvorak layout shown herestems from my early Kinesis years, using the Contour PS/2 with a Dvorak
+ * software layout. Because of this, the RBRC and LBRC were on opposite sides of the board in the corner
+ * keys. I've decided to continue using this layout with my ErgoDox.
+ *
+ * The QWERTY layout shown here is based entirely on the Kinesis Advantage layout, with the additional
+ * keys as shown in the diagrams. The Colemak layout is merely an adaptation of that.
+ *
+ * I've enabled persistent keymaps for Qwerty, Dvorak and Colemak layers, similar to the default Planck
+ * layouts.
+ *
+ * For a better explanation of the layout matrices shown below, take a look at ../../ez/ez.h where the
+ * keymap is defined, beginning on line 81.
+ *
+ */
+
+#include "ergodox.h"
+#include "debug.h"
+#include "action_layer.h"
+#include "eeconfig.h"
+
+extern keymap_config_t keymap_config;
+
+#define _DV 0 // Dvorak layer
+#define _QW 1 // Qwerty layer
+#define _CM 2 // Colemak layer
+#define _MD 3 // Media Layer
+#define _KP 4 // Keypad Layer
+
+// Macro name shortcuts
+#define DVORAK M(_DV)
+#define QWERTY M(_QW)
+#define COLEMAK M(_CM)
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+/* Keymap 0: Dvorak layer
+ *
+ * ,--------------------------------------------------. ,--------------------------------------------------.
+ * | ] | 1 | 2 | 3 | 4 | 5 | ESC | | ESC | 6 | 7 | 8 | 9 | 0 | [ |
+ * |--------+------+------+------+------+-------------| |------+------+------+------+------+------+--------|
+ * | Tab | ' | , | . | Y | Y | | | | F | G | C | R | L | \ |
+ * |--------+------+------+------+------+------| | | |------+------+------+------+------+--------|
+ * | CapsLk | A | O | E | U | I |------| |------| D | H | T | N | S | - |
+ * |--------+------+------+------+------+------| _MD | | _KP |------+------+------+------+------+--------|
+ * | LShift | Z | X | C | V | X | | | | B | M | W | V | Z | RShift |
+ * `--------+------+------+------+------+-------------' `-------------+------+------+------+------+--------'
+ * | LGUI | ` | INS | Left | Rght | | Up | Dn | / | = | RGUI |
+ * `----------------------------------' `----------------------------------'
+ * ,-------------. ,-------------.
+ * | LCtr | LAlt | | Ralt | RCtr |
+ * ,------|------|------| |------+------+------.
+ * | | | Home | | PgUp | | |
+ * | BkSp | Del |------| |------| Enter| Space|
+ * | | | End | | PgDn | | |
+ * `--------------------' `--------------------'
+ *
+ */
+// If it accepts an argument (i.e, is a function), it doesn't need KC_.
+// Otherwise, it needs KC_*
+[_DV] = { // layer 0 : Dvorak
+ // left hand
+ {KC_RBRC, KC_TAB, KC_CAPS, KC_LSFT, KC_LGUI, KC_NO },
+ {KC_1, KC_QUOT, KC_A, KC_SCLN, KC_GRV, KC_END },
+ {KC_2, KC_COMM, KC_O, KC_Q, KC_INS, KC_DEL },
+ {KC_3, KC_DOT, KC_E, KC_J, KC_LEFT, KC_BSPC},
+ {KC_4, KC_P, KC_U, KC_K, KC_RGHT, KC_HOME},
+ {KC_5, KC_Y, KC_I, KC_X, KC_NO, KC_LCTL},
+ {KC_ESC, KC_NO, KC_NO, MO(_MD), KC_NO, KC_LALT},
+
+ // right hand
+ {KC_ESC, KC_NO, KC_NO, MO(_KP), KC_NO, KC_RALT},
+ {KC_6, KC_F, KC_D, KC_B, KC_NO, KC_RCTL},
+ {KC_7, KC_G, KC_H, KC_M, KC_UP, KC_PGUP},
+ {KC_8, KC_C, KC_T, KC_W, KC_DOWN, KC_SPC },
+ {KC_9, KC_R, KC_N, KC_V, KC_SLSH, KC_ENT },
+ {KC_0, KC_L, KC_S, KC_Z, KC_EQL, KC_PGDN},
+ {KC_LBRC, KC_BSLS, KC_MINS, KC_RSFT, KC_RGUI, KC_NO }
+},
+
+/* Keymap 1: QWERTY layer
+ *
+ * ,--------------------------------------------------. ,--------------------------------------------------.
+ * | = | 1 | 2 | 3 | 4 | 5 | ESC | | ESC | 6 | 7 | 8 | 9 | 0 | - |
+ * |--------+------+------+------+------+-------------| |------+------+------+------+------+------+--------|
+ * | Tab | Q | W | E | R | T | | | | Y | U | I | O | P | \ |
+ * |--------+------+------+------+------+------| | | |------+------+------+------+------+--------|
+ * | CapsLk | A | S | D | F | G |------| |------| H | J | K | L | ; | ' |
+ * |--------+------+------+------+------+------| _MD | | _KP |------+------+------+------+------+--------|
+ * | LShift | Z | X | C | V | B | | | | N | M | , | . | / | RShift |
+ * `--------+------+------+------+------+-------------' `-------------+------+------+------+------+--------'
+ * | LGUI | ` | INS | Left | Rght | | Up | Dn | [ | ] | RGUI |
+ * `----------------------------------' `----------------------------------'
+ * ,-------------. ,-------------.
+ * | LCtr | LAlt | | Ralt | RCtr |
+ * ,------|------|------| |------+------+------.
+ * | | | Home | | PgUp | | |
+ * | BkSp | Del |------| |------| Enter| Space|
+ * | | | End | | PgDn | | |
+ * `--------------------' `--------------------'
+ */
+// If it accepts an argument (i.e, is a function), it doesn't need KC_.
+// Otherwise, it needs KC_*
+[_QW] = { // layer 1 : QWERTY
+ // left hand
+ {KC_EQL, KC_TAB, KC_CAPS, KC_LSFT, KC_LGUI, KC_NO },
+ {KC_1, KC_Q, KC_A, KC_Z, KC_GRV, KC_END },
+ {KC_2, KC_W, KC_S, KC_X, KC_INS, KC_DEL },
+ {KC_3, KC_E, KC_D, KC_C, KC_LEFT, KC_BSPC},
+ {KC_4, KC_R, KC_F, KC_V, KC_RGHT, KC_HOME},
+ {KC_5, KC_T, KC_G, KC_B, KC_NO, KC_LCTL},
+ {KC_ESC, KC_NO, KC_NO, MO(_MD), KC_NO, KC_LALT},
+
+ // right hand
+ {KC_ESC, KC_NO, KC_NO, MO(_KP), KC_NO, KC_RALT},
+ {KC_6, KC_Y, KC_H, KC_N, KC_NO, KC_RCTL},
+ {KC_7, KC_U, KC_J, KC_M, KC_UP, KC_PGUP},
+ {KC_8, KC_I, KC_K, KC_COMM, KC_DOWN, KC_SPC },
+ {KC_9, KC_O, KC_L, KC_DOT, KC_LBRC, KC_ENT },
+ {KC_0, KC_P, KC_SCLN, KC_SLSH, KC_RBRC, KC_PGDN},
+ {KC_MINS, KC_BSLS, KC_QUOT, KC_RSFT, KC_RGUI, KC_NO }
+ },
+
+/* Keymap 2: Colemak layer
+ *
+ * ,--------------------------------------------------. ,--------------------------------------------------.
+ * | = | 1 | 2 | 3 | 4 | 5 | ESC | | ESC | 6 | 7 | 8 | 9 | 0 | - |
+ * |--------+------+------+------+------+-------------| |------+------+------+------+------+------+--------|
+ * | Tab | Q | W | F | P | G | | | | J | L | U | Y | ; | \ |
+ * |--------+------+------+------+------+------| | | |------+------+------+------+------+--------|
+ * | BkSpc | A | R | S | T | D |------| |------| H | N | E | I | O | ' |
+ * |--------+------+------+------+------+------| _MD | | _KP |------+------+------+------+------+--------|
+ * | LShift | Z | X | C | V | B | | | | K | M | , | . | / | RShift |
+ * `--------+------+------+------+------+-------------' `-------------+------+------+------+------+--------'
+ * | LGUI | ` | INS | Left | Rght | | Up | Dn | [ | ] | RGUI |
+ * `----------------------------------' `----------------------------------'
+ * ,-------------. ,-------------.
+ * | LCtr | LAlt | | Ralt | RCtr |
+ * ,------|------|------| |------+------+------.
+ * | | | Home | | PgUp | | |
+ * | BkSp | Del |------| |------| Enter| Space|
+ * | | | End | | PgDn | | |
+ * `--------------------' `--------------------'
+ */
+// If it accepts an argument (i.e, is a function), it doesn't need KC_.
+// Otherwise, it needs KC_*
+[_CM] = { // layer 2 : Colemak
+ // left hand
+ {KC_EQL, KC_TAB, KC_BSPC, KC_LSFT, KC_LGUI, KC_NO },
+ {KC_1, KC_Q, KC_A, KC_Z, KC_GRV, KC_END },
+ {KC_2, KC_W, KC_R, KC_X, KC_INS, KC_DEL },
+ {KC_3, KC_F, KC_S, KC_C, KC_LEFT, KC_BSPC},
+ {KC_4, KC_P, KC_T, KC_V, KC_RGHT, KC_HOME},
+ {KC_5, KC_G, KC_D, KC_B, KC_NO, KC_LCTL},
+ {KC_ESC, KC_NO, KC_NO, MO(_MD), KC_NO, KC_LALT},
+
+ // right hand
+ {KC_ESC, KC_NO, KC_NO, MO(_KP), KC_NO, KC_RALT},
+ {KC_6, KC_J, KC_H, KC_K, KC_NO, KC_RCTL},
+ {KC_7, KC_L, KC_N, KC_M, KC_UP, KC_PGUP},
+ {KC_8, KC_U, KC_E, KC_COMM, KC_DOWN, KC_SPC },
+ {KC_9, KC_Y, KC_I, KC_DOT, KC_LBRC, KC_ENT },
+ {KC_0, KC_SCLN, KC_O, KC_SLSH, KC_RBRC, KC_PGDN},
+ {KC_MINS, KC_BSLS, KC_QUOT, KC_RSFT, KC_RGUI, KC_NO }
+ },
+
+/* Keymap 3: Symbol Layer
+ *
+ * ,--------------------------------------------------. ,--------------------------------------------------.
+ * | TEENSY | F1 | F2 | F3 | F4 | F5 | F11 | | F12 | F6 | F7 | F8 | F9 | F10 | |
+ * |--------+------+------+------+------+-------------| |------+------+------+------+------+------+--------|
+ * | | | PrSc | ScLk | Paus | | FN4 | | FN5 | | Mute | Vol- | Vol+ | | |
+ * |--------+------+------+------+------+------| | | |------+------+------+------+------+--------|
+ * | | | | | | |------| |------| Stop | Prev | Play | Next | Sel | |
+ * |--------+------+------+------+------+------| FN4 | | FN5 |------+------+------+------+------+--------|
+ * | | |Dvorak|Qwerty|Colemk| | | | | | | | | | |
+ * `--------+------+------+------+------+-------------' `-------------+------+------+------+------+--------'
+ * | | | | | | | | | | | |
+ * `----------------------------------' `----------------------------------'
+ * ,-------------. ,-------------.
+ * | | | | | |
+ * ,------|------|------| |------+------+------.
+ * | | | | | | | |
+ * | | |------| |------| | |
+ * | | | | | | | |
+ * `--------------------' `--------------------'
+ */
+// Media Layer
+[_MD] = { // layer 3 : Media layer
+ // left hand
+ {RESET, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO },
+ {KC_F1, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS},
+ {KC_F2, KC_PSCR, KC_TRNS, DVORAK, KC_TRNS, KC_TRNS},
+ {KC_F3, KC_SLCK, KC_TRNS, QWERTY, KC_TRNS, KC_TRNS},
+ {KC_F4, KC_PAUS, KC_TRNS, COLEMAK, KC_TRNS, KC_TRNS},
+ {KC_F5, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_TRNS},
+ {KC_F11, KC_NO, KC_NO, KC_TRNS, KC_NO, KC_TRNS},
+
+ // right hand
+ {KC_F12, KC_NO, KC_NO, KC_TRNS, KC_NO, KC_TRNS},
+ {KC_F6, KC_TRNS, KC_MSTP, KC_TRNS, KC_NO, KC_TRNS},
+ {KC_F7, KC_MUTE, KC_MPRV, KC_TRNS, KC_TRNS, KC_TRNS},
+ {KC_F8, KC_VOLD, KC_MPLY, KC_TRNS, KC_TRNS, KC_TRNS},
+ {KC_F9, KC_VOLU, KC_MNXT, KC_TRNS, KC_TRNS, KC_TRNS},
+ {KC_F10, KC_TRNS, KC_MSEL, KC_TRNS, KC_TRNS, KC_TRNS},
+ {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO }
+ },
+
+/* Keymap 4: Keypad layer
+ *
+ * ,--------------------------------------------------. ,--------------------------------------------------.
+ * | Power | | | | | | | | | | NmLk | KP / | KP * | KP - | |
+ * |--------+------+------+------+------+-------------| |------+------+------+------+------+------+--------|
+ * | Sleep | | | | | | FN5 | | FN4 | | KP 7 | KP 8 | KP 9 | KP + | |
+ * |--------+------+------+------+------+------| | | |------+------+------+------+------+--------|
+ * | Wake | | | | | |------| |------| | KP 4 | KP 5 | KP 6 | KP + | |
+ * |--------+------+------+------+------+------| FN5 | | FN4 |------+------+------+------+------+--------|
+ * | | | | | | | | | | | KP 1 | KP 2 | KP 3 |KP Ent| |
+ * `--------+------+------+------+------+-------------' `-------------+------+------+------+------+--------'
+ * | | | | | | | KP 0 | | KP . |KP Ent| |
+ * `----------------------------------' `----------------------------------'
+ * ,-------------. ,-------------.
+ * | | | | | |
+ * ,------|------|------| |------+------+------.
+ * | | | | | | | |
+ * | | |------| |------| | |
+ * | | | | | | | |
+ * `--------------------' `--------------------'
+ */
+// Keypad Layer
+[_KP] = { // layer 4 : Keypad layer
+ // left hand
+ {KC_PWR, KC_SLEP, KC_WAKE, KC_TRNS, KC_TRNS, KC_NO },
+ {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS},
+ {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS},
+ {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS},
+ {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS},
+ {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_TRNS},
+ {KC_TRNS, KC_NO, KC_NO, KC_TRNS, KC_NO, KC_TRNS},
+
+ // right hand
+ {KC_TRNS, KC_NO, KC_NO, KC_TRNS, KC_NO, KC_TRNS},
+ {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_TRNS},
+ {KC_NLCK, KC_P7, KC_P4, KC_P1, KC_P0, KC_TRNS},
+ {KC_PSLS, KC_P8, KC_P5, KC_P2, KC_NO, KC_TRNS},
+ {KC_PAST, KC_P9, KC_P6, KC_P3, KC_PDOT, KC_TRNS},
+ {KC_PMNS, KC_PPLS, KC_PPLS, KC_PENT, KC_PENT, KC_TRNS},
+ {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_NO }
+ },
+
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+void persistant_default_layer_set(uint16_t default_layer) {
+ eeconfig_update_default_layer(default_layer);
+ default_layer_set(default_layer);
+}
+
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+ switch(id) {
+ case _DV:
+ if (record->event.pressed) {
+ persistant_default_layer_set(1UL<<_DV);
+ }
+ break;
+ case _QW:
+ if (record->event.pressed) {
+ persistant_default_layer_set(1UL<<_QW);
+ }
+ break;
+ case _CM:
+ if (record->event.pressed) {
+ persistant_default_layer_set(1UL<<_CM);
+ }
+ break;
+ }
+ return MACRO_NONE;
+};
+
+// Runs just one time when the keyboard initializes.
+void matrix_init_user(void) {
+
+};
+
+// Runs constantly in the background, in a loop.
+void matrix_scan_user(void) {
+
+ uint8_t layer = biton32(layer_state);
+
+ ergodox_board_led_off();
+ ergodox_right_led_1_off();
+ ergodox_right_led_2_off();
+ ergodox_right_led_3_off();
+ switch (layer) {
+ // TODO: Make this relevant to the ErgoDox EZ.
+ case 1:
+ ergodox_right_led_1_on();
+ break;
+ case 2:
+ ergodox_right_led_2_on();
+ break;
+ default:
+ // none
+ break;
+ }
+
+};
--- /dev/null
+#include "phantom.h"
+#include "action_layer.h"
+#include "eeconfig.h"
+
+extern keymap_config_t keymap_config;
+
+
+// Used for SHIFT_ESC
+#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT))
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _QW 0
+#define _DV 1
+#define _CM 2
+#define _FL 3
+
+// Macro name shortcuts
+#define QWERTY M(_QW)
+#define DVORAK M(_DV)
+#define COLEMAK M(_CM)
+
+// Fillers to make layering more clear
+#define _______ KC_TRNS
+#define XXXXXXX KC_NO
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+[_QW] = { /* Layer 0: Qwerty */
+ {KC_ESC, KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_SLCK, KC_PAUS},
+ {KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, XXXXXXX, KC_BSPC, KC_INS, KC_HOME, KC_PGUP},
+ {KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_DEL, KC_END, KC_PGDN},
+ {KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, XXXXXXX, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX},
+ {KC_LSFT, XXXXXXX, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, XXXXXXX, KC_RSFT, XXXXXXX, KC_UP, XXXXXXX},
+ {KC_LCTL, KC_LGUI, KC_LALT, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, XXXXXXX, XXXXXXX, KC_RALT, KC_RGUI, MO(_FL), KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT}
+ },
+
+[_DV] = { /* Layer 1: Dvorak */
+ {KC_ESC, KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_SLCK, KC_PAUS},
+ {KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_LBRC, KC_RBRC, XXXXXXX, KC_BSPC, KC_INS, KC_HOME, KC_PGUP},
+ {KC_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_SLSH, KC_EQL, KC_BSLS, KC_DEL, KC_END, KC_PGDN},
+ {KC_CAPS, KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_MINS, XXXXXXX, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX},
+ {KC_LSFT, XXXXXXX, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, XXXXXXX, KC_RSFT, XXXXXXX, KC_UP, XXXXXXX},
+ {KC_LCTL, KC_LGUI, KC_LALT, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, XXXXXXX, XXXXXXX, KC_RALT, KC_RGUI, MO(_FL), KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT}
+ },
+
+[_CM] = { /* Layer 2: Colemak */
+ {KC_ESC, KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_SLCK, KC_PAUS},
+ {KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, XXXXXXX, KC_BSPC, KC_INS, KC_HOME, KC_PGUP},
+ {KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_LBRC, KC_RBRC, KC_BSLS, KC_DEL, KC_END, KC_PGDN},
+ {KC_BSPC, KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT, XXXXXXX, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX},
+ {KC_LSFT, XXXXXXX, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, XXXXXXX, KC_RSFT, XXXXXXX, KC_UP, XXXXXXX},
+ {KC_LCTL, KC_LGUI, KC_LALT, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, XXXXXXX, XXXXXXX, KC_RALT, KC_RGUI, MO(_FL), KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT}
+ },
+
+[_FL] = { /* Layer 3: Functions */
+ {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______},
+ {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, XXXXXXX, RESET, KC_MPRV, KC_MPLY, KC_MNXT},
+ {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MUTE, KC_VOLD, KC_VOLU},
+ {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, XXXXXXX, _______, XXXXXXX, XXXXXXX, XXXXXXX},
+ {_______, XXXXXXX, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, XXXXXXX, _______, XXXXXXX, _______, XXXXXXX},
+ {QWERTY, DVORAK, COLEMAK, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______, _______, _______},
+ },
+
+
+};
+
+enum function_id {
+ SHIFT_ESC,
+};
+
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+void persistant_default_layer_set(uint16_t default_layer) {
+ eeconfig_update_default_layer(default_layer);
+ default_layer_set(default_layer);
+}
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+ switch(id) {
+ case _DV:
+ if (record->event.pressed) {
+ persistant_default_layer_set(1UL<<_DV);
+ }
+ break;
+ case _QW:
+ if (record->event.pressed) {
+ persistant_default_layer_set(1UL<<_QW);
+ }
+ break;
+ case _CM:
+ if (record->event.pressed) {
+ persistant_default_layer_set(1UL<<_CM);
+ }
+ break;
+ }
+ return MACRO_NONE;
+};
--- /dev/null
+
+
+BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = no # Console for debug(+400)
+COMMAND_ENABLE = yes # Commands for debug and configuration
+NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
+MIDI_ENABLE = no # MIDI controls
+AUDIO_ENABLE = yes # Audio output on port C6
+UNICODE_ENABLE = no # Unicode
+BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
+
+SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+ include ../../../../Makefile
+endif
--- /dev/null
+#ifndef CONFIG_USER_H
+#define CONFIG_USER_H
+
+#include "../../config.h"
+
+#define FORCE_NKRO 1
+
+#endif
--- /dev/null
+#include "preonic.h"
+#include "action_layer.h"
+#include "eeconfig.h"
+#include "keymap_nordic.h"
+#ifdef AUDIO_ENABLE
+ #include "audio.h"
+#endif
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _QWERTY 0
+#define _LOWER 3
+#define _RAISE 4
+#define _ADJUST 16
+
+enum preonic_keycodes {
+ QWERTY = SAFE_RANGE,
+ LOWER,
+ RAISE,
+ BACKLIT
+};
+
+// Fillers to make layering more clear
+#define _______ KC_TRNS
+#define XXXXXXX KC_NO
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+/* Qwerty
+ * ,-----------------------------------------------------------------------------------.
+ * | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | + | Bksp |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | Esc | Q | W | E | R | T | Y | U | I | O | P | Å |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | Tab | A | S | D | F | G | H | J | K | L | Ö | Ä |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * | Shift| < | Z | X | C | V | B | N | M | . | , | - |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | Ctrl | GUI | Alt |AltGr |Lower | Space| Enter|Raise | Left | Down | Up |Right |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_QWERTY] = {
+ {KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, NO_PLUS, KC_BSPC},
+ {KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, NO_AM },
+ {KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, NO_AE, NO_OSLH},
+ {KC_LSFT, NO_LESS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_DOT, KC_COMM, NO_MINS},
+ {KC_LCTL, KC_LGUI, KC_LALT, NO_ALGR, LOWER, KC_SPC, KC_ENT, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT}
+},
+
+/* Lower
+ * ,-----------------------------------------------------------------------------------.
+ * | | @ | £ | $ | | | { | [ | ] | } | \ | Del |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | | | | | | | | |VolUp | | | ~ |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | | | | | | | |LastS |PauseP|NextS | | * |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * | | | | | | | | | |VolDwn| | | |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | |Bspc | | | | | |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_LOWER] = {
+ {_______, NO_AT, NO_PND, NO_DLR, _______, _______, NO_LCBR, NO_LBRC, NO_RBRC, NO_RCBR, NO_BSLS, KC_DEL},
+ {_______, _______, _______, _______, _______, _______, _______, _______, KC_VOLU, _______, _______, NO_TILD},
+ {_______, _______, _______, _______, _______, _______, _______, KC_MPRV, KC_MPLY, KC_MNXT, _______, LSFT(KC_BSLS)},
+ {_______, NO_PIPE, _______, _______, _______, _______, _______, _______, KC_VOLD, _______, _______, _______},
+ {_______, _______, _______, _______, _______, _______, KC_BSPC, _______, _______, _______, _______, _______}
+},
+
+/* Raise
+ * ,-----------------------------------------------------------------------------------.
+ * | ! | " | # | ¤ | % | & | / | ( | ) | = | ? | Ins |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | |Mouse^| | | | |ScrlUp| | | ^ |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | | |Mouse<|MouseV|Mouse>| | |MLC |MMC |MRC | ' | " |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * | | > | | | | | | |ScrlDown| : | ; | _ |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | |Bspc | | | | | | |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_RAISE] = {
+ {LSFT(KC_1),NO_QUO2,LSFT(KC_3), NO_BULT,LSFT(KC_5), NO_AMPR, NO_SLSH, NO_LPRN, NO_RPRN, NO_EQL, NO_QUES, KC_INS},
+ {_______, _______, _______, KC_MS_U, _______, _______, _______, _______, KC_WH_U, _______, _______, NO_CIRC},
+ {_______, _______, KC_MS_L, KC_MS_D, KC_MS_R, _______, _______, KC_BTN1, KC_BTN3, KC_BTN2, NO_APOS, NO_QUOT},
+ {_______, NO_GRTR, _______, _______, _______, _______, _______, _______, KC_WH_D, NO_COLN, NO_SCLN, NO_UNDS},
+ {_______, _______, _______, _______, _______, KC_BSPC, _______, _______, _______, _______, _______, _______}
+},
+
+/* Adjust (Lower + Raise)
+ * ,-----------------------------------------------------------------------------------.
+ * | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | Reset| | | | | | | | |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | | | | | | | | | | | |Rsft |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * | |MusOn |MusOff| | | | | | | | | Reset|
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | | | | | |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_ADJUST] = {
+ {KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12},
+ {_______, _______, _______, RESET, _______, _______, _______, _______, _______, _______, _______, _______},
+ {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_RSFT},
+ {_______, MU_ON, MU_OFF, _______, _______, _______, _______, _______, _______, _______, _______, RESET },
+ {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______}
+}
+
+
+};
+
+#ifdef AUDIO_ENABLE
+float tone_startup[][2] = {
+ {NOTE_B5, 20},
+ {NOTE_B6, 8},
+ {NOTE_DS6, 20},
+ {NOTE_B6, 8}
+};
+
+float tone_qwerty[][2] = SONG(QWERTY_SOUND);
+
+float tone_goodbye[][2] = SONG(GOODBYE_SOUND);
+
+float music_scale[][2] = SONG(MUSIC_SCALE_SOUND);
+#endif
+
+void persistant_default_layer_set(uint16_t default_layer) {
+ eeconfig_update_default_layer(default_layer);
+ default_layer_set(default_layer);
+}
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+ switch (keycode) {
+ case QWERTY:
+ if (record->event.pressed) {
+ #ifdef AUDIO_ENABLE
+ PLAY_NOTE_ARRAY(tone_qwerty, false, 0);
+ #endif
+ persistant_default_layer_set(1UL<<_QWERTY);
+ }
+ return false;
+ break;
+ case LOWER:
+ if (record->event.pressed) {
+ layer_on(_LOWER);
+ update_tri_layer(_LOWER, _RAISE, _ADJUST);
+ } else {
+ layer_off(_LOWER);
+ update_tri_layer(_LOWER, _RAISE, _ADJUST);
+ }
+ return false;
+ break;
+ case RAISE:
+ if (record->event.pressed) {
+ layer_on(_RAISE);
+ update_tri_layer(_LOWER, _RAISE, _ADJUST);
+ } else {
+ layer_off(_RAISE);
+ update_tri_layer(_LOWER, _RAISE, _ADJUST);
+ }
+ return false;
+ break;
+ case BACKLIT:
+ if (record->event.pressed) {
+ register_code(KC_RSFT);
+ #ifdef BACKLIGHT_ENABLE
+ backlight_step();
+ #endif
+ } else {
+ unregister_code(KC_RSFT);
+ }
+ return false;
+ break;
+ }
+ return true;
+};
+
+void matrix_init_user(void) {
+ #ifdef AUDIO_ENABLE
+ startup_user();
+ #endif
+}
+
+#ifdef AUDIO_ENABLE
+
+void startup_user()
+{
+ _delay_ms(20); // gets rid of tick
+ PLAY_NOTE_ARRAY(tone_startup, false, 0);
+}
+
+void shutdown_user()
+{
+ PLAY_NOTE_ARRAY(tone_goodbye, false, 0);
+ _delay_ms(150);
+ stop_all_notes();
+}
+
+void music_on_user(void)
+{
+ music_scale_user();
+}
+
+void music_scale_user(void)
+{
+ PLAY_NOTE_ARRAY(music_scale, false, 0);
+}
+
+#endif
--- /dev/null
+# Jacwib's preonic keymap.
+
+Designed for use with a swedish language.
--- /dev/null
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+# change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes # Console for debug(+400)
+COMMAND_ENABLE ?= yes # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= yes # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE ?= no # MIDI controls
+UNICODE_ENABLE ?= no # Unicode
+BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no # Audio output on port C6
+
+ifndef QUANTUM_DIR
+ include ../../Makefile
+endif
+
+
--- /dev/null
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0xFEAE
+#define PRODUCT_ID 0x8844
+#define DEVICE_VER 0x0002
+#define MANUFACTURER Evan Sailer
+#define PRODUCT TheVan 44
+#define DESCRIPTION keyboard firmware for TV44
+
+/* key matrix size */
+#define MATRIX_ROWS 4
+#define MATRIX_COLS 12
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D7, B5, F7, D4 }
+#define MATRIX_COL_PINS { D2, D3, D5, D6, B4, B6, F6, F5, F4, F1, F0, B3 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1 H
+//#define MAGIC_KEY_HELP2 SLASH
+//#define MAGIC_KEY_DEBUG D
+//#define MAGIC_KEY_DEBUG_MATRIX X
+//#define MAGIC_KEY_DEBUG_KBD K
+//#define MAGIC_KEY_DEBUG_MOUSE M
+//#define MAGIC_KEY_VERSION V
+//#define MAGIC_KEY_STATUS S
+//#define MAGIC_KEY_CONSOLE C
+//#define MAGIC_KEY_LAYER0_ALT1 ESC
+//#define MAGIC_KEY_LAYER0_ALT2 GRAVE
+//#define MAGIC_KEY_LAYER0 0
+//#define MAGIC_KEY_LAYER1 1
+//#define MAGIC_KEY_LAYER2 2
+//#define MAGIC_KEY_LAYER3 3
+//#define MAGIC_KEY_LAYER4 4
+//#define MAGIC_KEY_LAYER5 5
+//#define MAGIC_KEY_LAYER6 6
+//#define MAGIC_KEY_LAYER7 7
+//#define MAGIC_KEY_LAYER8 8
+//#define MAGIC_KEY_LAYER9 9
+//#define MAGIC_KEY_BOOTLOADER PAUSE
+//#define MAGIC_KEY_LOCK CAPS
+//#define MAGIC_KEY_EEPROM E
+//#define MAGIC_KEY_NKRO N
+//#define MAGIC_KEY_SLEEP_LED Z
+
+/*
+ * Feature disable options
+ * These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
--- /dev/null
+# Build Options
+# change to "no" to disable the options, or define them in the Makefile in
+# the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = no # Console for debug(+400)
+COMMAND_ENABLE = yes # Commands for debug and configuration
+NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
+MIDI_ENABLE = no # MIDI controls
+AUDIO_ENABLE = no # Audio output on port C6
+UNICODE_ENABLE = no # Unicode
+BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
+SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+ include ../../../../Makefile
+endif
\ No newline at end of file
--- /dev/null
+#ifndef CONFIG_USER_H
+#define CONFIG_USER_H
+
+#include "../../config.h"
+
+// place overrides here
+
+#endif
\ No newline at end of file
--- /dev/null
+#include "tv44.h"
+#include "action_layer.h"
+#include "eeconfig.h"
+
+extern keymap_config_t keymap_config;
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+
+#define _QW 0
+#define _DV 1
+#define _CM 2
+#define _L1 3
+#define _L2 4
+#define _L3 5
+
+// Macro name shortcuts
+#define QWERTY M(_QW)
+#define DVORAK M(_DV)
+#define COLEMAK M(_CM)
+
+// Fillers to make layering more clear
+#define _______ KC_TRNS
+#define XXXXXXX KC_NO
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ [_QW] = { /* Qwerty */
+ {KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC },
+ {MO(_L1), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, MO(_L1) },
+ {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_F, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, MO(_L2) },
+ {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_RALT, KC_ESC, XXXXXXX, TG(_L3) }
+ },
+ [_DV] = { /* Dvorak */
+ {KC_TAB, KC_COMM, KC_DOT, KC_SLSH, KC_Q, KC_Q, KC_Q, KC_Q, KC_Q, KC_Q, KC_Q, KC_BSPC },
+ {MO(_L1), KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, MO(_L1) },
+ {KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, MO(_L2) },
+ {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_RALT, KC_ESC, XXXXXXX, TG(_L3) }
+ },
+ [_CM] = { /* Colemak */
+ {KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC },
+ {MO(_L1), KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, MO(_L1) },
+ {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, MO(_L2) },
+ {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_RALT, KC_ESC, XXXXXXX, TG(_L3) }
+ },
+ [_L1] = { /* LAYER 1 */
+ {KC_GRV, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL },
+ {_______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_DOWN, KC_UP, KC_LEFT, KC_RGHT, _______ },
+ {_______, KC_ESC, _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT },
+ {_______, KC_LGUI, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, XXXXXXX, _______ }
+ },
+ [_L2] = { /* LAYER 2 */
+ {_______, QWERTY, DVORAK, COLEMAK, _______, _______, _______, KC_7, KC_8, KC_9, KC_0, _______ },
+ {KC_ESC, KC_PIPE, KC_DQUO, KC_UNDS, KC_PLUS, LSFT(KC_LBRC), LSFT(KC_RBRC), KC_4, KC_5, KC_6, KC_VOLU, KC_ENT },
+ {_______, _______, _______, _______, _______, _______, KC_0, KC_1, KC_2, KC_3, KC_VOLD, _______ },
+ {_______, _______, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, XXXXXXX, _______ }
+ },
+ [_L3] = { /* LAYER 3 */
+ {_______, _______, _______, _______, _______, _______, _______, KC_F1, KC_F2, KC_F3, KC_F4, _______ },
+ {KC_ESC, _______, _______, _______, _______, _______, _______, KC_F5, KC_F6, KC_F7, KC_F8, _______ },
+ {KC_LSFT, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_F9, KC_F10, KC_F11, KC_F12, _______ },
+ {_______, KC_LSFT, KC_B, KC_SPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_C, _______, _______, XXXXXXX, _______ }
+ }
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+void persistant_default_layer_set(uint16_t default_layer) {
+ eeconfig_update_default_layer(default_layer);
+ default_layer_set(default_layer);
+}
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+ switch(id) {
+ case _DV:
+ if (record->event.pressed) {
+ persistant_default_layer_set(1UL<<_DV);
+ }
+ break;
+ case _QW:
+ if (record->event.pressed) {
+ persistant_default_layer_set(1UL<<_QW);
+ }
+ break;
+ case _CM:
+ if (record->event.pressed) {
+ persistant_default_layer_set(1UL<<_CM);
+ }
+ break;
+ }
+ return MACRO_NONE;
+};
--- /dev/null
+# The default keymap for tv44
\ No newline at end of file
--- /dev/null
+# Build Options
+# change to "no" to disable the options, or define them in the Makefile in
+# the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = no # Console for debug(+400)
+COMMAND_ENABLE = yes # Commands for debug and configuration
+NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
+MIDI_ENABLE = no # MIDI controls
+AUDIO_ENABLE = no # Audio output on port C6
+UNICODE_ENABLE = no # Unicode
+BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
+SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+ include ../../../../Makefile
+endif
\ No newline at end of file
--- /dev/null
+#ifndef CONFIG_USER_H
+#define CONFIG_USER_H
+
+#include "../../config.h"
+
+// place overrides here
+
+#endif
\ No newline at end of file
--- /dev/null
+#include "tv44.h"
+#include "action_layer.h"
+#include "eeconfig.h"
+
+extern keymap_config_t keymap_config;
+
+#define _DV 0
+#define _QW 1
+#define _CM 2
+#define _L1 3
+#define _L2 4
+
+// Macro name shortcuts
+#define DVORAK M(_DV)
+#define QWERTY M(_QW)
+#define COLEMAK M(_CM)
+
+// Fillers to make layering more clear
+#define _______ KC_TRNS
+#define XXXXXXX KC_NO
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ [_DV] = { /* 0: Dvorak */
+ {KC_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_BSPC },
+ {MO(_L1), KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_ENT },
+ {KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, KC_RSFT },
+ {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) }
+ },
+
+ [_QW] = { /* 1: Qwerty */
+ {KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC },
+ {MO(_L1), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_ENT },
+ {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT },
+ {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) }
+ },
+
+ [_CM] = { /* 2: Colemak */
+ {KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC },
+ {MO(_L1), KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_ENT },
+ {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT },
+ {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) }
+ },
+
+ [_L1] = {/* 1: FN 1 */
+ {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL },
+ {_______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_DOWN, KC_UP, KC_LEFT, KC_RGHT, _______ },
+ {_______, _______, _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT },
+ {KC_ESC, KC_LGUI, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, KC_SLSH, _______, _______ }
+ },
+
+ [_L2] = { /* 2: FN 2 */
+ {KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_ESC },
+ {_______, KC_F11, KC_F12, _______, _______, _______, _______, _______, KC_HOME, KC_PGUP, KC_VOLU, KC_ENT },
+ {_______, _______, _______, _______, _______, _______, _______, _______, KC_END, KC_PGDN, KC_VOLD, _______ },
+ {QWERTY, DVORAK, COLEMAK, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______ }
+ }
+
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+void persistant_default_layer_set(uint16_t default_layer) {
+ eeconfig_update_default_layer(default_layer);
+ default_layer_set(default_layer);
+}
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+ switch(id) {
+ case _DV:
+ if (record->event.pressed) {
+ persistant_default_layer_set(1UL<<_DV);
+ }
+ break;
+ case _QW:
+ if (record->event.pressed) {
+ persistant_default_layer_set(1UL<<_QW);
+ }
+ break;
+ case _CM:
+ if (record->event.pressed) {
+ persistant_default_layer_set(1UL<<_CM);
+ }
+ break;
+ }
+ return MACRO_NONE;
+};
+
+
--- /dev/null
+# The default keymap for tv44
\ No newline at end of file
--- /dev/null
+tv44 keyboard firmware
+======================
+
+## Quantum MK Firmware
+
+For the full Quantum feature list, see [the parent readme.md](/doc/readme.md).
+
+## Building
+
+Download or clone the whole firmware and navigate to the keyboards/tv44 folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file.
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+
+To build with the default keymap, simply run `make`.
+
+### Other Keymaps
+
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files.
+
+To build the firmware binary hex file with a keymap just do `make` with `keymap` option like:
+
+```
+$ make keymap=[default|jack|<name>]
+```
+
+Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/`
\ No newline at end of file
--- /dev/null
+#include "tv44.h"
+
+void matrix_init_kb(void) {
+ // put your keyboard start-up code here
+ // runs once when the firmware starts up
+
+ matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+ // put your looping keyboard code here
+ // runs every cycle (a lot)
+
+ matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+ // put your per-action keyboard code here
+ // runs for every action, just before processing by the firmware
+
+ return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+ // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+ led_set_user(usb_led);
+}
--- /dev/null
+#ifndef TV44_H
+#define TV44_H
+
+#include "quantum.h"
+
+// This a shortcut to help you visually see your layout.
+// The following is an example using the Planck MIT layout
+// The first section contains all of the arguements
+// The second converts the arguments into a two-dimensional array
+#define KEYMAP( \
+ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \
+ K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \
+ K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \
+ K30, K31, K32, K33, K37, K38, K39, K3B \
+) \
+{ \
+ { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B }, \
+ { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B }, \
+ { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B }, \
+ { K30, K31, K32, K33, KC_NO, KC_NO, KC_NO, K37, K38, K39, K3A, K3B } \
+
+#endif
}
}
-void set_unicode_mode(uint8_t os_target)
+void set_unicode_input_mode(uint8_t os_target)
{
input_mode = os_target;
}
projects / qmk_firmware.git / commitdiff