--- /dev/null
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x6060
+#define DEVICE_VER 0x0001
+#define MANUFACTURER OkKeebs LLC
+#define PRODUCT Puck
+#define DESCRIPTION 4x3 macropad
+
+/* key matrix size */
+#define MATRIX_ROWS 4
+#define MATRIX_COLS 3
+
+#define MATRIX_ROW_PINS { D2, D3, C6, C7 }
+#define MATRIX_COL_PINS { B4, D7, D6 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION ROW2COL
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* number of backlight levels */
+#define BACKLIGHT_LEVELS 3
+
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
--- /dev/null
+#include QMK_KEYBOARD_H
+
+#define _BL 0
+#define _HL 1
+#define _LL 2
+
+enum keycodes {
+ LOW,
+ HIGH
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ /*
+ * Base Layer (Numbers)
+ */
+ [_BL] = LAYOUT(
+ KC_KP_7, KC_KP_8, KC_KP_9,
+ KC_KP_4, KC_KP_5, KC_KP_6,
+ KC_KP_1, KC_KP_2, KC_KP_3,
+ LOW, KC_KP_0, HIGH
+ ),
+ /*
+ * High Layer (Work)
+ */
+ [_HL] = LAYOUT(
+ KC_NUMLOCK, KC_PAST, KC_NO,
+ KC_PMNS, KC_PENT, KC_PPLS,
+ KC_NO, KC_PSLS, KC_NO,
+ KC_NO, KC_PDOT, KC_NO
+ ),
+ /*
+ * Low Layer (Media)
+ */
+ [_LL] = LAYOUT(
+ KC_NO, KC_VOLU, KC_NO,
+ KC_MPRV, KC_MPLY, KC_MNXT,
+ KC_NO, KC_VOLD, KC_NO,
+ KC_NO, KC_NO, KC_NO
+ ),
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+ switch(keycode) {
+ case HIGH:
+ if (record->event.pressed) {
+ layer_on(_HL);
+ }else{
+ layer_off(_HL);
+ layer_off(_LL);
+ }
+ return false;
+ break;
+ case LOW:
+ if (record->event.pressed) {
+ layer_on(_LL);
+ }else{
+ layer_off(_LL);
+ layer_off(_HL);
+ }
+ return false;
+ break;
+ }
+ return true;
+}
--- /dev/null
+#include "puck.h"
--- /dev/null
+#ifndef PUCK_H
+#define PUCK_H
+
+#include "quantum.h"
+
+#define LAYOUT( \
+ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B \
+) { \
+ { K00, K01, K02 }, \
+ { K03, K04, K05 }, \
+ { K06, K07, K08 }, \
+ { K09, K0A, K0B }, \
+}
+
+#endif
--- /dev/null
+A 4 x 3 macropad.
+
+Keyboard Maintainer: [john-pettigrew](https://github.com/john-pettigrew)
+Hardware Supported: Puck PCB.
+Hardware Availability: [OkKeebs.com](https://okkeebs.com/products/puck-pcb)
+
+Make example for this keyboard (after setting up your build environment):
+
+ make puck:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
--- /dev/null
+
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+BOOTLOADER = halfkay
+
+# Build Options
+# change to "no" to disable the options, or define them in the Makefile in
+# the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = no # Console for debug(+400)
+COMMAND_ENABLE = no # Commands for debug and configuration
+NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
+MIDI_ENABLE = no # MIDI controls
+AUDIO_ENABLE = no # Audio output on port C6
+UNICODE_ENABLE = no # Unicode
+BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
projects / qmk_firmware.git / commitdiff