# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
-BOOTLOADER = lufa-ms
+BOOTLOADER = atmel-dfu # actually lufa-ms
# Build Options
# change yes to no to disable
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
-BOOTLOADER = atmel_dfu
+BOOTLOADER = atmel-dfu
# Build Options
# change yes to no to disable
+++ /dev/null
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = no # Console for debug(+400)
-COMMAND_ENABLE = yes # Commands for debug and configuration
-NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
-MIDI_ENABLE = no # MIDI controls
-AUDIO_ENABLE = no # Audio output on port C6
-UNICODE_ENABLE = no # Unicode
-BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
-SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = atmel-dfu # actually lufa-ms
# Mass storage bootloader on the tada68 uses bin files
-FIRMWARE_FORMAT=bin
+FIRMWARE_FORMAT = bin
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no # Mouse keys(+4700)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = yes # Console for debug(+400)
+CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality (+4870)
-
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-BOOTLOADER=caterina
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = caterina
# Build Options
# comment out to disable the options.
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
TAP_DANCE_ENABLE = no
-
-
-OPT_DEFS += -DMITOSIS_PROMICRO
-MITOSIS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
- avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
-
-# # project specific files
-SRC = matrix.c
-
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = caterina
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Build Options
# comment out to disable the options.
#
# upload: build
# $(MITOSIS_UPLOAD_COMMAND)
+
+OPT_DEFS += -DMITOSIS_PROMICRO
+MITOSIS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
+ avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
+
+# # project specific files
+SRC = matrix.c
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-BOOTLOADER =qmk-dfu
-
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = qmk-dfu
# Build Options
# comment out to disable the options.
# MCU name
MCU = atmega32u4
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = atmel-dfu
# Build Options
# change yes to no to disable
+++ /dev/null
-# Copyright 2017 Balz Guenat
-#
-# This program is free software: you can redistribute it and/or modify
-# it under the terms of the GNU General Public License as published by
-# the Free Software Foundation, either version 2 of the License, or
-# (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program. If not, see <http://www.gnu.org/licenses/>.
-
-
-# QMK Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-# BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-# MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-# EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-# CONSOLE_ENABLE = no # Console for debug(+400)
-# COMMAND_ENABLE = yes # Commands for debug and configuration
-# NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-# BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
-# MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
-# AUDIO_ENABLE = no # Audio output on port C6
-# UNICODE_ENABLE = no # Unicode
-# BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
-# RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
-# SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = atmel-dfu
# Build Options
# comment out to disable the options.
NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
BACKLIGHT_ENABLE = yes
-
# Optimize size but this may cause error "relocation truncated to fit"
#EXTRALDFLAGS = -Wl,--relax
# MCU name
MCU = atmega32u4
-
# Bootloader selection
-# Teensy halfkay
-# Pro Micro caterina
-# Atmel DFU atmel-dfu
-# LUFA DFU lufa-dfu
-# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
+++ /dev/null
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = no # Console for debug(+400)
-COMMAND_ENABLE = yes # Commands for debug and configuration
-NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
-MIDI_ENABLE = no # MIDI controls
-AUDIO_ENABLE = no # Audio output on port C6
-UNICODE_ENABLE = no # Unicode
-BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
-SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = atmel-dfu
# Build Options
# change yes to no to disable
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = yes # Console for debug(+400)
+CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
+++ /dev/null
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = no # Console for debug(+400)
-COMMAND_ENABLE = yes # Commands for debug and configuration
-NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
-MIDI_ENABLE = no # MIDI controls
-AUDIO_ENABLE = no # Audio output on port C6
-UNICODE_ENABLE = no # Unicode
-BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
-SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = atmel-dfu
# Build Options
# change yes to no to disable
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = yes # Console for debug(+400)
+CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
# Build Options
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = atmel-dfu
# Build Options
# comment out to disable the options.
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality
AUDIO_ENABLE ?= no
-RGBLIGHT_ENABLE ?= no
\ No newline at end of file
+RGBLIGHT_ENABLE ?= no
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
# Build Options
# MCU name
MCU = atmega32u4
-SRC = matrix.c i2c_master.c
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = caterina
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
+
+SRC += matrix.c i2c_master.c
-
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
#
-TAP_DANCE_ENABLE = no
-
# If your custom treadstone32 pcb, you can rewrite to yes.
RGBLIGHT_ENABLE = yes # LED underglow (Enable WS2812 RGB underlight.)
LED_ANIMATIONS = yes # LED animations
ifeq ($(strip $(IOS_DEVICE_ENABLE)), yes)
OPT_DEFS += -DIOS_DEVICE_ENABLE
endif
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Build Options
# change yes to no to disable
#
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
LEADER_ENABLE = no
-
-
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no # Mouse keys(+4700)
-EXTRAKEY_ENABLE = no # Audio control and System control(+450)
-CONSOLE_ENABLE = no # Console for debug(+400)
-COMMAND_ENABLE = no # Commands for debug and configuration
-NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
-MIDI_ENABLE = no # MIDI controls
-AUDIO_ENABLE = no # Audio output on port C6
-UNICODE_ENABLE = no # Unicode
-BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
-SWAP_HANDS_ENABLE = no # Enable one-hand typing
TAP_DANCE_ENABLE = yes
# If your custom treadstone48 pcb, you can rewrite to yes.
-SRC += i2c.c
-SRC += serial.c
-SRC += ssd1306.c
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = caterina
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
CUSTOM_MATRIX = yes
DEFAULT_FOLDER = treadstone48/rev1
+
+SRC += i2c.c
+SRC += serial.c
+SRC += ssd1306.c
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no # Mouse keys(+4700)
-EXTRAKEY_ENABLE = no # Audio control and System control(+450)
-CONSOLE_ENABLE = no # Console for debug(+400)
-COMMAND_ENABLE = no # Commands for debug and configuration
-NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
-MIDI_ENABLE = no # MIDI controls
-AUDIO_ENABLE = no # Audio output on port C6
-UNICODE_ENABLE = no # Unicode
-BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight.
-SWAP_HANDS_ENABLE = no # Enable one-hand typing
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
+RGBLIGHT_ENABLE = yes
-# if firmware size over limit, try this option
-# CFLAGS += -flto
-
# MCU name
MCU = atmega32u4
# ATmega328P USBasp
BOOTLOADER = caterina
-# Use split_common libraries
-SPLIT_KEYBOARD = yes
-
-DEFAULT_FOLDER = uzu42/rev1
-
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
OLED_DRIVER_ENABLE = no # OLED display
+SPLIT_KEYBOARD = yes
+
+DEFAULT_FOLDER = uzu42/rev1
+++ /dev/null
-BACKLIGHT_ENABLE = no
-RGBLIGHT_ENABLE = no
+++ /dev/null
-BACKLIGHT_ENABLE = no
-RGBLIGHT_ENABLE = no
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = yes # Console for debug(+400)
-COMMAND_ENABLE = yes # Commands for debug and configuration
-NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
-MIDI_ENABLE = no # MIDI controls
-AUDIO_ENABLE = yes # Audio output on port C6
-UNICODE_ENABLE = no # Unicode
-BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
-SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
-
+AUDIO_ENABLE = yes
-SPLIT_KEYBOARD = yes
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = caterina
+
+SPLIT_KEYBOARD = yes
-SPLIT_KEYBOARD = yes # Rev2 uses split_common
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = qmk-dfu
+
+SPLIT_KEYBOARD = yes
DEFAULT_FOLDER = vitamins_included/rev2
-LINK_TIME_OPTIMIZATION_ENABLE = yes
\ No newline at end of file
+LINK_TIME_OPTIMIZATION_ENABLE = yes
# MCU name
MCU = atmega32u4
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
# MCU name
MCU = atmega32u4
-# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
# Build Options
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
-HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
\ No newline at end of file
+HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
-# project specific files
-SRC = keyboards/wilba_tech/wt_main.c \
- keyboards/wilba_tech/wt_rgb_backlight.c \
- quantum/color.c \
- drivers/issi/is31fl3731.c \
- drivers/avr/i2c_master.c
-
# MCU name
MCU = atmega32u4
DYNAMIC_KEYMAP_ENABLE = yes
CIE1931_CURVE = yes
-#LAYOUTS = ???
+# project specific files
+SRC = keyboards/wilba_tech/wt_main.c \
+ keyboards/wilba_tech/wt_rgb_backlight.c \
+ quantum/color.c \
+ drivers/issi/is31fl3731.c \
+ drivers/avr/i2c_master.c
-# project specific files
-SRC = keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
RAW_ENABLE = yes
DYNAMIC_KEYMAP_ENABLE = yes
+
+# project specific files
+SRC = keyboards/wilba_tech/wt_main.c
-
-
-# project specific files
-SRC = keyboards/wilba_tech/wt_main.c \
- keyboards/wilba_tech/wt_rgb_backlight.c \
- quantum/color.c \
- drivers/issi/is31fl3731.c \
- drivers/avr/i2c_master.c
-
# MCU name
MCU = atmega32u4
CIE1931_CURVE = yes
LAYOUTS = 60_hhkb
+
+# project specific files
+SRC = keyboards/wilba_tech/wt_main.c \
+ keyboards/wilba_tech/wt_rgb_backlight.c \
+ quantum/color.c \
+ drivers/issi/is31fl3731.c \
+ drivers/avr/i2c_master.c
-# project specific files
-SRC = keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
# backlight effects.
OPT_DEFS += -DNO_SUSPEND_POWER_DOWN
-
# Build Options
# change yes to no to disable
#
DYNAMIC_KEYMAP_ENABLE = yes
CIE1931_CURVE = no
+# project specific files
+SRC = keyboards/wilba_tech/wt_main.c
-# project specific files
-SRC = keyboards/wilba_tech/wt_main.c \
- keyboards/wilba_tech/wt_rgb_backlight.c \
- quantum/color.c \
- drivers/issi/is31fl3218.c \
- drivers/avr/i2c_master.c
-
# MCU name
MCU = atmega32u4
# backlight effects.
OPT_DEFS += -DNO_SUSPEND_POWER_DOWN
-
# Build Options
# change yes to no to disable
#
DYNAMIC_KEYMAP_ENABLE = yes
CIE1931_CURVE = yes
+# project specific files
+SRC = keyboards/wilba_tech/wt_main.c \
+ keyboards/wilba_tech/wt_rgb_backlight.c \
+ quantum/color.c \
+ drivers/issi/is31fl3218.c \
+ drivers/avr/i2c_master.c
-# project specific files
-SRC = keyboards/wilba_tech/wt_main.c \
- keyboards/wilba_tech/wt_rgb_backlight.c \
- quantum/color.c \
- drivers/issi/is31fl3731.c \
- drivers/avr/i2c_master.c
-
# MCU name
MCU = atmega32u4
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
RAW_ENABLE = yes
DYNAMIC_KEYMAP_ENABLE = yes
CIE1931_CURVE = yes
+
+# project specific files
+SRC = keyboards/wilba_tech/wt_main.c \
+ keyboards/wilba_tech/wt_rgb_backlight.c \
+ quantum/color.c \
+ drivers/issi/is31fl3731.c \
+ drivers/avr/i2c_master.c
RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file
+DYNAMIC_KEYMAP_ENABLE = yes
-# project specific files
-SRC = drivers/issi/is31fl3736.c \
- drivers/avr/i2c_master.c \
- quantum/color.c \
- keyboards/wilba_tech/wt_mono_backlight.c \
- keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC = drivers/issi/is31fl3736.c \
+ drivers/avr/i2c_master.c \
+ quantum/color.c \
+ keyboards/wilba_tech/wt_mono_backlight.c \
+ keyboards/wilba_tech/wt_main.c
RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file
+DYNAMIC_KEYMAP_ENABLE = yes
-# project specific files
-SRC = keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file
+DYNAMIC_KEYMAP_ENABLE = yes
+
+# project specific files
+SRC = keyboards/wilba_tech/wt_main.c
RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file
+DYNAMIC_KEYMAP_ENABLE = yes
-# project specific files
-SRC = drivers/issi/is31fl3736.c \
- drivers/avr/i2c_master.c \
- quantum/color.c \
- keyboards/wilba_tech/wt_mono_backlight.c \
- keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC = drivers/issi/is31fl3736.c \
+ drivers/avr/i2c_master.c \
+ quantum/color.c \
+ keyboards/wilba_tech/wt_mono_backlight.c \
+ keyboards/wilba_tech/wt_main.c
RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file
+DYNAMIC_KEYMAP_ENABLE = yes
-# project specific files
-SRC = drivers/issi/is31fl3736.c \
- drivers/avr/i2c_master.c \
- quantum/color.c \
- keyboards/wilba_tech/wt_mono_backlight.c \
- keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC = drivers/issi/is31fl3736.c \
+ drivers/avr/i2c_master.c \
+ quantum/color.c \
+ keyboards/wilba_tech/wt_mono_backlight.c \
+ keyboards/wilba_tech/wt_main.c
RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file
+DYNAMIC_KEYMAP_ENABLE = yes
-# project specific files
-SRC = keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC = keyboards/wilba_tech/wt_main.c
RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file
+DYNAMIC_KEYMAP_ENABLE = yes
-# project specific files
-SRC = drivers/issi/is31fl3736.c \
- drivers/avr/i2c_master.c \
- quantum/color.c \
- keyboards/wilba_tech/wt_mono_backlight.c \
- keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC = drivers/issi/is31fl3736.c \
+ drivers/avr/i2c_master.c \
+ quantum/color.c \
+ keyboards/wilba_tech/wt_mono_backlight.c \
+ keyboards/wilba_tech/wt_main.c
RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file
+DYNAMIC_KEYMAP_ENABLE = yes
-# project specific files
-SRC = drivers/issi/is31fl3736.c \
- drivers/avr/i2c_master.c \
- quantum/color.c \
- keyboards/wilba_tech/wt_mono_backlight.c \
- keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC = drivers/issi/is31fl3736.c \
+ drivers/avr/i2c_master.c \
+ quantum/color.c \
+ keyboards/wilba_tech/wt_mono_backlight.c \
+ keyboards/wilba_tech/wt_main.c
RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file
+DYNAMIC_KEYMAP_ENABLE = yes
-# project specific files
-SRC = drivers/issi/is31fl3736.c \
- drivers/avr/i2c_master.c \
- quantum/color.c \
- keyboards/wilba_tech/wt_mono_backlight.c \
- keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC = drivers/issi/is31fl3736.c \
+ drivers/avr/i2c_master.c \
+ quantum/color.c \
+ keyboards/wilba_tech/wt_mono_backlight.c \
+ keyboards/wilba_tech/wt_main.c
RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file
+DYNAMIC_KEYMAP_ENABLE = yes
-# project specific files
-SRC = drivers/issi/is31fl3736.c \
- drivers/avr/i2c_master.c \
- quantum/color.c \
- keyboards/wilba_tech/wt_mono_backlight.c \
- keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC = drivers/issi/is31fl3736.c \
+ drivers/avr/i2c_master.c \
+ quantum/color.c \
+ keyboards/wilba_tech/wt_mono_backlight.c \
+ keyboards/wilba_tech/wt_main.c
-# project specific files
-SRC = keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC = keyboards/wilba_tech/wt_main.c
-# project specific files
-SRC = keyboards/wilba_tech/wt_main.c \
- keyboards/wilba_tech/wt_rgb_backlight.c \
- quantum/color.c \
- drivers/issi/is31fl3731.c \
- drivers/avr/i2c_master.c
-
# MCU name
MCU = atmega32u4
CIE1931_CURVE = yes
LAYOUTS = 60_ansi 60_iso 60_hhkb 60_ansi_split_bs_rshift
+
+# project specific files
+SRC = keyboards/wilba_tech/wt_main.c \
+ keyboards/wilba_tech/wt_rgb_backlight.c \
+ quantum/color.c \
+ drivers/issi/is31fl3731.c \
+ drivers/avr/i2c_master.c
-# project specific files
-SRC = keyboards/wilba_tech/wt_main.c \
- keyboards/wilba_tech/wt_rgb_backlight.c \
- quantum/color.c \
- drivers/issi/is31fl3731.c \
- drivers/avr/i2c_master.c
-
# MCU name
MCU = atmega32u4
RAW_ENABLE = yes
DYNAMIC_KEYMAP_ENABLE = yes
CIE1931_CURVE = yes
+
+# project specific files
+SRC = keyboards/wilba_tech/wt_main.c \
+ keyboards/wilba_tech/wt_rgb_backlight.c \
+ quantum/color.c \
+ drivers/issi/is31fl3731.c \
+ drivers/avr/i2c_master.c
# MCU name
MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-# LUFA specific
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = atmel-dfu
# Build Options
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
# MCU name
MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-# LUFA specific
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+++ /dev/null
-# Copyright 2013 Jun Wako <wakojun@gmail.com>
-#
-# This program is free software: you can redistribute it and/or modify
-# it under the terms of the GNU General Public License as published by
-# the Free Software Foundation, either version 2 of the License, or
-# (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program. If not, see <http://www.gnu.org/licenses/>.
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = atmel-dfu
# QMK Build Options
# change to "no" to disable the options, or define them in the Makefile in
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE = lite
COMMAND_ENABLE = no
-RGBLIGHT_ENABLE = yes
\ No newline at end of file
+RGBLIGHT_ENABLE = yes
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = atmel-dfu
# Build Options
# comment out to disable the options.
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality
AUDIO_ENABLE ?= no
-RGBLIGHT_ENABLE ?= no
\ No newline at end of file
+RGBLIGHT_ENABLE ?= no
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
# Build Options
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# comment out to disable the options.
#
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = no # Console for debug(+400)
-COMMAND_ENABLE = no # Commands for debug and configuration
-NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
-MIDI_ENABLE = no # MIDI controls
-AUDIO_ENABLE = no # Audio output on port C6
-UNICODE_ENABLE = no # Unicode
-BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight.
-SWAP_HANDS_ENABLE = no # Enable one-hand typing
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
+EXTRAKEY_ENABLE = yes
+RGBLIGHT_ENABLE = yes
# If you want to change the display of OLED, you need to change here
SRC += ./lib/glcdfont.c \
-SRC += i2c.c
-SRC += serial.c
-SRC += ssd1306.c
-
-# if firmware size over limit, try this option
-# CFLAGS += -flto
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = caterina
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
CUSTOM_MATRIX = yes
DEFAULT_FOLDER = yosino58/rev1
+
+SRC += i2c.c
+SRC += serial.c
+SRC += ssd1306.c
-
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
-#SRC += i2c.c
-SRC += serial.c
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = caterina
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
CUSTOM_MATRIX = yes
DEFAULT_FOLDER = zinc/rev1
+
+#SRC += i2c.c
+SRC += serial.c
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
# Build Options
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = atmel-dfu
# Build Options
# comment out to disable the options.
projects / qmk_firmware.git / commitdiff