#define BREATHE_LED_ADDRESS CAPS_LOCK_LED_ADDRESS
#endif
-#define DEBUG_ENABLED 0
+#define DEBUG_ENABLED 1
/* =================
* ChibiOS I2C setup
//TODO: lighting key led on keypress
break;
- //TODO: custom page that is written using keypresses
//TODO: BLINK_ON/OFF_LED
+ break;
case OFF_LED:
//on/off/toggle single led, msg_led = row/col of led
- xprintf("OFF_LED\n");
+ xprintf("OFF_LED: %d\n", msg_led);
chThdSleepMilliseconds(10);
set_led_bit(7, control_register_word, msg_led, 0);
is31_write_data (7, control_register_word, 0x02);
break;
-
case ON_LED:
- xprintf("ON_LED\n");
+ xprintf("ON_LED: %d\n", msg_led);
chThdSleepMilliseconds(10);
set_led_bit(7, control_register_word, msg_led, 1);
is31_write_data (7, control_register_word, 0x02);
break;
-
case TOGGLE_LED:
- xprintf("TOGGLE_LED\n");
+ xprintf("TOGGLE_LED: %d\n", msg_led);
chThdSleepMilliseconds(10);
set_led_bit(7, control_register_word, msg_led, 2);
is31_write_data (7, control_register_word, 0x02);
break;
+ case BLINK_OFF_LED:
+ //on/off/toggle single led, msg_led = row/col of led
+ xprintf("BLINK_ON: %d\n", msg_led);
+ chThdSleepMilliseconds(10);
+ set_led_bit(7, control_register_word, msg_led, 4);
+ is31_write_data (7, control_register_word, 0x02);
+ break;
+ case BLINK_ON_LED:
+ xprintf("BLINK_OFF: %d\n", msg_led);
+ chThdSleepMilliseconds(10);
+ set_led_bit(7, control_register_word, msg_led, 5);
+ is31_write_data (7, control_register_word, 0x02);
+ break;
+ case BLINK_TOGGLE_LED:
+ xprintf("BLINK_TOGGLE: %d\n", msg_led);
+ chThdSleepMilliseconds(10);
+ set_led_bit(7, control_register_word, msg_led, 6);
+ is31_write_data (7, control_register_word, 0x02);
+
case TOGGLE_ALL:
- xprintf("TOGGLE_ALL\n");
+ xprintf("TOGGLE_ALL: %d\n", msg_led);
chThdSleepMilliseconds(10);
//msg_led = unused
is31_read_register(0, 0x00, &temp);//if first byte is on, then toggle frame 0 off
led_control_reg[0] = 0;
+
if (temp==0 || page_status > 0) {
- xprintf("all leds on");
- chThdSleepMilliseconds(10);
__builtin_memcpy(led_control_reg+1, all_on_leds_mask, 0x12);
} else {
- xprintf("all leds off");
- chThdSleepMilliseconds(10);
__builtin_memset(led_control_reg+1, 0, 0x12);
}
is31_write_data(0, led_control_reg, 0x13);
case DISPLAY_PAGE://show single layer indicator or full map of layer
//msg_led = page to toggle on
- xprintf("DISPLAY_PAGE\n");
+ xprintf("DISPLAY_PAGE");
chThdSleepMilliseconds(10);
if (page_status != msg_led) {
+ xprintf(" - new page\n");
+ chThdSleepMilliseconds(10);
is31_write_register(IS31_FUNCTIONREG, IS31_REG_PICTDISP, msg_led);
}
page_status = msg_led;
break;
case RESET_PAGE:
+ xprintf("RESET_PAGE\n");
+ chThdSleepMilliseconds(10);
//led_msg = page to reset
led_control_reg[0] = 0;
__builtin_memset(led_control_reg+1, 0, 0x12);
case TOGGLE_NUM_LOCK:
//msg_led = 0 or 1, off/on
- set_lock_leds(USB_LED_NUM_LOCK, msg_led);
+ xprintf("NUMLOCK: %d\n", msg_led);
+ chThdSleepMilliseconds(10);
+ set_lock_leds(NUM_LOCK_LED_ADDRESS, msg_led);
break;
case TOGGLE_CAPS_LOCK:
+ xprintf("CAPSLOCK: %d\n", msg_led);
+ chThdSleepMilliseconds(10);
//msg_led = 0 or 1, off/on
- set_lock_leds(USB_LED_CAPS_LOCK, msg_led);
+ set_lock_leds(CAPS_LOCK_LED_ADDRESS, msg_led);
break;
//TODO: MODE_BREATH
case MODE_BREATH:
break;
case STEP_BRIGHTNESS:
- xprintf("TOGGLE_BACKLIGHT\n");
+ xprintf("STEP_BACKLIGHT\n");
chThdSleepMilliseconds(10);
//led_msg = step pwm up or down
switch (msg_led) {
chThdSleepMilliseconds(10);
}
#if DEBUG_ENABLED
- uint8_t j, page;
+ uint8_t j;
+ uint8_t pages[3]={0x00, 0x07};
//debugging code - print full led/blink/pwm registers on each frame
xprintf("----layer state----: %X\n", layer_state);
- for(i=0;i<8;i++) {
- xprintf("page: %d", i);
- chThdSleepMilliseconds(2);
- for(j=0;j<0xB4;j++){
- is31_read_register(i,j,&temp);
+ for(i=0;i<2;i++) {
+ xprintf("page: %d\n", pages[i]);
chThdSleepMilliseconds(2);
- xprintf("%02X, ", temp);
- if(j % 9 == 0){
+ for(j=0;j<0x24;j++){
+ if(j > 0 && j % 9 == 0){
xprintf("\n");
- if(j % 18 ==0){
- xprintf("register");
- xprintf("\n");
- }
+ }
+ switch (j) {
+ case 0:
+ xprintf("\n--on-off--\n");
+ chThdSleepMilliseconds(2);
+ break;
+ case 0x12:
+ xprintf("\n--blink--\n");
+ chThdSleepMilliseconds(2);
+ break;
}
- chThdSleepMilliseconds(1);
+ is31_read_register(pages[i],j,&temp);
+ xprintf("%02X, ", temp);
+ chThdSleepMilliseconds(2);
}
+
+ xprintf("\n--pwm--\n");
+ chThdSleepMilliseconds(2);
+ for(j=0x24;j<0xB4;j++) {
+ is31_read_register(pages[i],j,&temp);
+ xprintf("%02X, ", temp);
+ chThdSleepMilliseconds(2);
+ if(j > 0x24 && (j-4) % 8 == 0){
xprintf("\n");
+ }
+ }
+ xprintf("\n");
+ }
+
+ //Function Register
+ xprintf("\n--FUNCTION--\n");
+ chThdSleepMilliseconds(2);
+ for(j=0;j<0x0D;j++) {
+ is31_read_register(0x0B,j,&temp);
+ switch(j) {
+ case 0:
+ xprintf("Config %02X", temp);
+ chThdSleepMilliseconds(2);
+ break;
+ case 1:
+ xprintf(" - Pict %02X\n", temp);
+ chThdSleepMilliseconds(2);
+ break;
+ case 2:
+ xprintf("Auto1 %02X", temp);
+ chThdSleepMilliseconds(2);
+ break;
+ case 3:
+ xprintf(" - Auto2 %02X\n", temp);
+ chThdSleepMilliseconds(2);
+ break;
+ case 5:
+ xprintf("Disp %02X", temp);
+ chThdSleepMilliseconds(2);
+ break;
+ case 6:
+ xprintf(" - Audio %02X\n", temp);
+ chThdSleepMilliseconds(2);
+ break;
+ case 7:
+ xprintf("Frame %02X", temp);
+ chThdSleepMilliseconds(2);
+ break;
+ case 8:
+ xprintf(" - Breath1 %02X\n", temp);
+ chThdSleepMilliseconds(2);
+ break;
+ case 9:
+ xprintf("Breath2 %02X - ", temp);
+ chThdSleepMilliseconds(2);
+ break;
+ case 10:
+ xprintf(" - Shut %02X\n", temp);
+ chThdSleepMilliseconds(2);
+ break;
+ case 11:
+ xprintf("AGC %02X", temp);
+ chThdSleepMilliseconds(2);
+ break;
+ case 12:
+ xprintf(" - ADC %02X\n", temp);
+ chThdSleepMilliseconds(2);
+ break;
}
+ }
#endif
}
}
void set_led_bit (uint8_t page, uint8_t *led_control_reg, uint8_t led_addr, uint8_t action) {
//returns 2 bytes led control register address and byte to write
+ //0 - bit off, 1 - bit on, 2 - toggle bit
+
+ uint8_t control_reg_addr, column_bit, column_byte, temp, blink_on;
- uint8_t control_reg_addr, column_bit, column_byte, temp;
//check for valid led address
- if (led_addr < 0 || led_addr > 90 || led_addr % 10 > 8) {
+ if (led_addr < 0 || led_addr > 87 || led_addr % 10 > 8) {
xprintf("Invalid address: %d\n", led_addr);
return;
}
+ xprintf("set_led_bit: %d\n", led_addr);
+ xprintf("action: %d\n", action);
+ chThdSleepMilliseconds(10);
+ //check blink bit
+ blink_on = action>>2;
+ action &= ~(1<<2); //strip blink bit
+
//first byte is led control register address 0x00
//msg_led tens column is pin#, ones column is bit position in 8-bit mask
control_reg_addr = ((led_addr / 10) % 10 - 1 ) * 0x02;// A-register is every other byte
+ xprintf("pre-reg_addr: %X\n", control_reg_addr);
+ chThdSleepMilliseconds(10);
+ control_reg_addr += blink_on == 1 ? 0x12 : 0x00;//shift 12 bytes to blink register
+ xprintf("blink-reg_addr: %X\n", control_reg_addr);
+ chThdSleepMilliseconds(10);
+
column_bit = 1<<(led_addr % 10 - 1);
is31_read_register(page, control_reg_addr, &temp);//maintain status of leds on this byte
column_byte = temp;
+ xprintf("column_byte read: %X\n", column_byte);
+ chThdSleepMilliseconds(10);
switch(action) {
case 0:
column_byte &= ~column_bit;
column_byte ^= column_bit;
break;
}
+ xprintf("column_byte write: %X\n", column_byte);
+ chThdSleepMilliseconds(10);
//return word to be written in register
led_control_reg[0] = control_reg_addr;
led_control_reg[1] = column_byte;
}
-void set_lock_leds(uint8_t lock_type, uint8_t led_on) {
- uint8_t page, led_addr, start, temp;
- uint8_t led_control_word[2] = {0};
- //TODO: this function call could send led address vs lock_type.
- //however, the switch/case allows for additional steps, like audio, depending on type
+void write_led_byte (uint8_t page, uint8_t row, uint8_t led_byte) {
+ uint8_t led_control_word[2] = {0};//register address and led on/off mask
- led_addr = 0;
- switch(lock_type) {
- case USB_LED_NUM_LOCK:
- led_addr = NUM_LOCK_LED_ADDRESS;
- break;
- case USB_LED_CAPS_LOCK:
- led_addr = CAPS_LOCK_LED_ADDRESS;
- break;
- #ifdef SCROLL_LOCK_LED_ADDRESS
- case USB_LED_SCROLL_LOCK:
- led_addr = SCROLL_LOCK_LED_ADDRESS;
- break;
- #endif
- #ifdef COMPOSE_LED_ADDRESS
- case USB_LED_COMPOSE:
- led_addr = COMPOSE_LED_ADDRESS;
- break;
- #endif
- #ifdef SCROLL_LOCK_LED_ADDRESS
- case USB_LED_KANA:
- led_addr = KANA_LED_ADDRESS;
- break;
- #endif
- }
-
- //ignore frame0 if all leds are on or if option set in led_controller.h
- //TODO: blink of all leds are on, clear blink register if not
- is31_read_register(0, 0x00, &temp);
- led_addr += temp == 0 ? 0 : 0x12;//send bit to blink register instead
- start = BACKLIGHT_OFF_LOCK_LED_OFF ? 1 : 0;
-
- for(page=start; page<8; page++) {
- set_led_bit(page,led_control_word,led_addr,led_on);
- is31_write_data(page, led_control_word, 0x02);
- }
+ led_control_word[0] = (row - 1 ) * 0x02;// A-register is every other byte
+ led_control_word[1] = led_byte;// A-register is every other byte
+ is31_write_data(page, led_control_word, 0x13);
}
void write_led_page (uint8_t page, uint8_t *user_led_array, uint8_t led_count) {
uint8_t i;
- uint8_t row, col;
+ uint8_t pin, col;
uint8_t led_control_register[0x13] = {0};//led control register start address + 0x12 bytes
__builtin_memset(led_control_register,0,13);
for(i=0;i<led_count;i++){
- row = ((user_led_array[i] / 10) % 10 - 1 ) * 2 + 1;// 1 byte shift for led register 0x00 address
+ pin = ((user_led_array[i] / 10) % 10 - 1 ) * 2 + 1;// 1 byte shift for led register 0x00 address
col = user_led_array[i] % 10 - 1;
- led_control_register[row] |= 1<<(col);
+ led_control_register[pin] |= 1<<(col);
}
is31_write_data(page, led_control_register, 0x13);
}
+void set_lock_leds(uint8_t led_addr, uint8_t led_action) {
+ uint8_t page, temp;
+ uint8_t led_control_word[2] = {0};
+
+ //blink if all leds are on
+ //is31_read_register(0, 0x00, &temp);
+ //if (temp != 0x00) {
+ // set_led_bit(0,led_control_word,led_addr,(led_action | (1<<2))); //set blink bit
+ //} else {
+ // set_led_bit(0,led_control_word,led_addr,led_action);
+ //}
+ //is31_write_data(0, led_control_word, 0x02);
+
+ for(page=1; page<8; page++) {
+ set_led_bit(page,led_control_word,led_addr,led_action);
+ is31_write_data(page, led_control_word, 0x02);
+ }
+}
+
/* =====================
* hook into user keymap
* ===================== */
is31_init();
//set Display Option Register so all pwm intensity is controlled from Frame 0
- is31_write_register(IS31_FUNCTIONREG, IS31_REG_DISPLAYOPT, IS31_REG_DISPLAYOPT_INTENSITY_SAME);
+ //enable blink and set blink period to 0.27s x rate
+ is31_write_register(IS31_FUNCTIONREG, IS31_REG_DISPLAYOPT, IS31_REG_DISPLAYOPT_INTENSITY_SAME + S31_REG_DISPLAYOPT_BLINK_ENABLE + 5);
/* set full pwm on Frame 1 */
pwm_register_array[0] = 0;
is31_write_register(IS31_FUNCTIONREG, IS31_REG_BREATHCTRL1, (3<<4)|3);
is31_write_register(IS31_FUNCTIONREG, IS31_REG_BREATHCTRL2, IS31_REG_BREATHCTRL2_ENABLE|3);
- // clean up the lock LEDs
- set_lock_leds(USB_LED_NUM_LOCK, 0);
- set_lock_leds(USB_LED_CAPS_LOCK, 0);
-
/* more time consuming LED processing should be offloaded into
* a thread, with asynchronous messaging. */
chMBObjectInit(&led_mailbox, led_mailbox_queue, LED_MAILBOX_NUM_MSGS);
projects / qmk_firmware.git / commitdiff